99-3527 - Kit voiture Metra - Free user manual and instructions

USER MANUAL 99-3527 Metra

Installation instructions for part 99-3527

• DIN radio provision with pocket
• ISO DIN radio provision with pocket

KIT COMPONENTS

• A) Radio housing • B) Trim plate • C) ISO brackets

A

B

C

Interior view of a car air conditioning unit with three rotary controls (no visible text or labels)

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • GMOS-01 • GMOS-04

Antenna Adapter: • 40-GM10

TOOLS REQUIRED

- Phillips screwdriver • Panel removal tool • 9/32" socket wrench

Table of Contents

Dash Disassembly 2

Kit Assembly

• DIN radio provision with pocket 3
• ISO DIN radio provision with pocket 3

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

METRA. The World's best kits. ^TM

metraonline.com

© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION

99-3527

Dash Disassembly

1. Remove the bezel from around the key cylinder. (Figure A)
2. Unclip and remove the entire panel surrounding the radio, including the message center and the vents. (Figure B)
3. To remove the radio, start at bottom of the stack and remove (8) 9/32" screws from the pocket, climate control, and the radio. (Figure C)

Line drawing of a car dashboard with control panel and buttons (no text or symbols)

(Figure A)

Diagram showing car dashboard and infotainment device with labeled buttons and gauges

(Figure B)

Diagram of a vehicle's front-mounted air intake system with directional arrows indicating airflow or movement (no text or labels)

(Figure C)

Continue to kit assembly

99-3527

Kit Assembly

DIN radio provision with pocket

1. Remove the metal DIN sleeve from the aftermarket radio.
2. Slide the sleeve into the radio housing and secure by bending the metal locking tabs down. (Figure A)
3. Slide the radio back into the sleeve until it clicks in. (Figure B)
4. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio and climate controls. Metra recommends using the proper mating adapter from Metra or AXXESS. Test the radio for proper operation.
5. Reassemble the dash in reverse order of disassembly.

Illustration of a hand using a tool to adjust or install a device into a rack (no text or symbols visible)

(Figure A) (Figure A)

Technical line drawing of an electronic device chassis with ports and connectors (no text or symbols)

(Figure B) (Figure B)

ISO DIN radio provision with pocket

1. Remove the metal DIN sleeve and trim ring from the aftermarket radio
2. Secure the ISO brackets to the radio with the screws supplied with the radio. (Figure A)
3. Slide the radio into the radio housing until the side clips engage. (Figure B)
4. Snap the trim plate into the radio housing. (Figure B)
5. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio and climate controls. Metra recommends using the proper mating adapter from Metra or AXXESS. Test the radio for proper operation.
6. Reassemble the dash in reverse order of disassembly.

Line drawing of a hand inserting a screwdriver into a computer drive (no text or symbols)

RIGHT SIDE CLIP

Installation instructions for part 99-3527

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected

enrolling in the most recognized and respected mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certified technicians