99-5812 - Kit voiture Metra - Free user manual and instructions

USER MANUAL 99-5812 Metra

INSTALLATION INSTRUCTIONS FOR PART 99-5812

APPLICATIONS

FORD

Edge 2007 / Expedition 2007

F-150 2004-07 / FreeStar 2004-07

Mustang 2005-07 / Five-Hundred 2005-07

Freestyle 2005-07 / Focus 2005-07 / Super Duty 2008

F Series 2005-07 / Fusion 2006-07 / Explorer 2006-07

Ford Explorer Sport Trac 2006-07

Ford Taurus 2008, Ford Taurus X 2008

MERCURY

Monterey 2004-07 / Milan 2006-07

Montego 2005-07 / Mountaineer 2006-07

Sable 2008

LINCOLN

Mark LT 2005-07

Factory Navigation Only: MKX 2007 / MKZ 2007 / Navigator 2007

Zephyr 2006

99-5812

KIT FEATURES

• DIN Head Unit Provision with Pocket
• ISO DIN Head Unit Provision with Pocket

KIT COMPONENTS

Interior view of a car dashboard with air vent and control knobs (no visible text or symbols)

Technical line drawing of a mechanical component with labeled section A (no text or symbols on the diagram itself)

D

E

F

TOOLS REQUIRED:

Cutting Tool • Phillips Screwdriver • Socket Wrench

1-800-221-0932

www.metraonline.com

© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION

TABLE OF CONTENTS

Dash Disassembly

Lincoln MKX 2007 ....11

Lincoln MKZ 2007....12,13

Lincoln Zephyr 2006....12.13

Lincoln Navigator 2007....14

Kit Assembly

DIN Head Unit Provision 15

ISO DIN Head Unit Provision....16

Final Assembly 17

*Note: Refer also to the instructions included with the aftermarket radio.

FORD F-150 2004-2007 LINCOLN MARK LT 2005-07 FORD EXPEDITION 2007 FORD EDGE 2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unsnap and remove entire panel surrounding the radio and climate controls. (Figure A)
3 Remove (4) 9/32" screws to remove the factory radio. (Figure B)

Continue to kit assembly

Line drawing of hands operating a car air conditioner panel with control buttons and dials (no text or symbols)

B

Top-down line drawing of a car air vent with labeled buttons and airflow indicators (no text or symbols)

FORD MUSTANG 2005-2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Remove the small rectangular shifter lever trim panel if equipped. (Figure A)
3 Remove (2) Phillips screws from under the center armrest at the back of the shifter trim panel (including cup holders). (Figure B)
4 Unclip and remove panel. (Figure B)
5 Unclip and remove the (2) center stack trim panels from the left and right side of the radio and climate controls. (Figure C)
6 Remove (6) 9/32" screws from center trim panel surrounding the radio and climate controls then unclip and remove panel. (Figure D)
7 Remove (4) 9/32" screws from the radio to remove. (Figure E)

Continue to kit assembly

E

Line drawing of a car interior showing hand operating controls and a vehicle chassis (no text or symbols)

A

Line drawing of a person using a tool on a mechanical device (no text or symbols)

B

Line drawing of a car interior showing steering wheel, dashboard, and fan (no text or symbols)

C

Line drawing of hands operating a mechanical device with arrows indicating motion (no text or symbols)

D

Line drawing of a car interior showing hand positioning and control panel (no text or symbols)

FORD FIVE-HUNDRED 2005-2007, FORD TAURUS 2008 MERCURY MONTEGO 2005-2007, MERCURY SABLE 2008

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove the small rectangular trim around shift lever. (Figure A)
3 Unclip and remove the entire panel (including cup holders) surrounding the shift lever. (Figure B)
4 Remove (2) 9/32" screws at the bottom of the center radio/ climate control panel. (Figure C)
5 Unclip and remove the center panel. (Figure D)
6 Remove (4) 9/32" screws from the radio to remove. (Figure E)

Continue to kit assembly

E

Illustration of a hand holding a device with arrows indicating assembly or connection (no text or symbols present)

A

Illustration of a hand using a tool to adjust or install a device (no text or symbols visible)

B

Line drawing of a car interior compartment with hand holding lid (no text or symbols)

C

Illustration of hands using a tool to adjust or install electronic components (no text or symbols visible)

D

Illustration of hands holding a tablet device with arrows indicating motion (no text or symbols)

FORD FUSION 2006-2007 MERCURY MILAN 2006-2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unsnap and remove entire panel surrounding the radio and climate controls. (Figure A)
3 Remove (4) 9/32" screws to remove the factory radio. (Figure B)

Continue to kit assembly

A

B

Diagram of a car air conditioner unit with arrows indicating airflow or movement (no text or symbols)

FORD FREESTYLE 2005-2007 FORD TAURUS X 2008

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove entire panel surrounding the radio and a/c controls. (Figure A)
3 Remove (4) 9/32" screws from radio to remove. (Figure B)

Continue to kit assembly

Line drawing of a car dashboard with hands installing or adjusting the controls (no text or symbols visible)

B

FORD FREESTAR 2004-2007 MERCURY MONTEREY 2004-2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unsnap and remove entire panel surrounding the radio and climate controls. (Figure A)
3 Remove (4) 9/32" screws to remove the factory radio. (Figure B)

Continue to kit assembly

A

Diagram of a device front panel with labeled ports and connectors (no text or symbols)

FORD FOCUS 2005-2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unsnap and remove entire panel surrounding the radio and climate controls. (Figure A)
3 Remove (4) 9/32" screws to remove the factory radio. (Figure B)

Continue to kit assembly

Line drawing of a car dashboard with control panel and directional arrow (no text or symbols)

B

Diagram of a car's rear panel showing internal components and cable routing (no text or labels)

FORD EXPLORER 2006-2007

FORD SPORT TRAC 2006-2007

MERCURY MOUNTAINEER 2006-2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Open center console and remove (2) Phillips screws then unclip and remove entire panel surrounding shifter. (Figure A)

Diagram of a mechanical device with directional arrows indicating movement or force (no text or symbols present)

Diagram of a car interior showing airflow or traffic flow from the steering wheel to the dashboard (no text or labels)

3 Remove dash panel surrounding radio to access the factory radio screws. (Figure B)

4 Remove (4) 9/32" screws to remove the factory radio. (Figure C)

Continue to kit assembly

C

FORD F SERIES SUPER DUTY 2005-2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unsnap and remove entire panel surrounding the radio and climate controls. (Figure A)

A

3 Remove (4) 9/32" screws to remove the factory radio. (Figure B)

Continue to kit assembly

B

FORD SUPER DUTY 2008

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove the power outlet panel and the blank panel on the left and right side of the radio trim panel. (Figure A)

A

Diagram of an airplane cockpit with labeled controls and directional arrows indicating flight path or movement.

3 Remove the (2) 9/32" screws exposed behind the two panels remove in step 2.
4 Unclip and remove the entire radio trim panel including the a/c control and vents.
5 Remove (4) 9/32" screws securing the radio.

Continue to kit assembly

LINCOLN MKX 2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Open center console lid and unclip and remove the center console trim panel surrounding the shifter. (Figure A)
3 Remove (2) Phillips screws from the storage bin then unclip and remove the bin. (Figure B)
4 Unclip and remove the upper and lower center trim panel as one assembly. (Figure C)
5 Remove (4) 9/32" screws securing the radio. Unplug and remove the Radio.

Continue to kit assembly

A

Line drawing of a car intake console with directional arrow indicating top view (no text or symbols)

B

Diagram of a car interior showing hand positioning and control panel (no text or symbols)

C

Line drawing of a car air conditioner unit with airflow indicators (no text or symbols)

LINCOLN MKZ 2007 / LINCOLN ZEPHYR 2006

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Open and remove the top of the center console. (Figure A)
3 Open ashtray door and remove ashtray then remove (1) Phillips screw from inside ashtray cavity. Close ashtray door.
4 Unclip and remove the climate control and trim panel assembly starting at the bottom edge. (Figure B)
5 Open the climate control vents and pull straight outward to remove. (Figure C)

Continue on next page

A

Diagram of a vehicle chassis with directional arrows indicating movement or force (no text or symbols)

B

Line drawing of an airplane cabin interior showing controls, seats, and directional arrows (no text or symbols)

C

Front view line drawing of a car dashboard with no visible text or symbols

LINCOLN MKZ 2007 / LINCOLN ZEPHYR 2006

6 Remove (2) 9/32" from the bottom of the radio trim panel assembly and (2) 9/32" screws from inside the vents. (Figure D)
7 Unclip the radio trim panel/radio assembly. Unplug and remove assembly. (Figure D)
8 Remove (4) 9/32" screws securing the radio to the trim panel and remove the radio. (Figure E)

Continue to kit assembly

D

Top-down line drawing of a car dashboard with control knobs and display (no text or symbols)

E

Technical line drawing of an electrical enclosure with internal components and directional arrows (no text or symbols)

LINCOLN NAVIGATOR 2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove the panel surrounding the shifter. (Figure A)
3 Remove (2) 9/32" screws from the bottom of the radio/climate control trim panel. (Figure B)
4 Unclip and remove the entire panel surrounding the radio and including the climate controls. (Figure B)
5 Remove (4) 9/32" screws securing the radio. Unplug and remove the Radio.

Continue to kit assembly

A

Interior view of a car dashboard with air intake control panel and directional arrow (no text or symbols)

B

Interior view of a car dashboard with instrument panel and control panel (no text or symbols visible)

DIN HEAD UNIT PROVISION

NOTE: Refer also to the instructions included with the aftermarket radio.

1 (a) For the Ford Edge/Expedition 2007, Explorer 2006-07, Fusion 2006-07, Mustang 2007 and the Super Duty 2008 attach the included spacers to the back of the radio housing mounting tabs. (Figure 1A) NOTE: Use the screws supplied with this kit to mount the radio housing in the vehicles that require the spacers.

(b) For the Ford Freestar 2004-07, Monterey 2004-07, Focus 2005-07, and the F Series Super Duty 2005-07, slide the included brackets onto the sides of the radio housings pocket from the back of the housing forward. (Figure 1B)

If your vehicle is not listed above move to step 2.

2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A)

3 Slide the aftermarket radio into the cage until it snaps in place. (Figure B)

Continue to final assembly

Technical line drawing of a mechanical component with arrows indicating assembly or movement (no text or symbols)

1B

Technical line drawing of a mechanical assembly with mounting brackets and structural supports (no text or symbols)

A

Technical diagram showing a hand using a tool to adjust or install electronic components with labeled parts and directional arrows.

B

Technical line drawing of an electronic device with mounting bracket and control panel (no text or symbols)

ISO DIN HEAD UNIT PROVISION

NOTE: Refer also to the instructions included with the aftermarket radio.

1 (a) For the Ford/Edge Expedition 2007, Explorer 2006-07, Fusion 2006-07, Mustang 2007 and the Super Duty 2008 attach the included spacers to the back of the radio housing mounting tabs. (Figure 1A) NOTE: Use the screws supplied with this kit to mount the radio housing in the vehicles that require the spacers.

(b) For the Ford Freestar 2004-07, Monterey 2004-07, Focus 2005-07, and the F Series Super Duty 2005-07, slide the included brackets onto the sides of the radio housings pocket from the back of the housing forward. (Figure 1B)

If your vehicle is not listed above move to step 2.

2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A)

3 Slide the head unit into the radio opening until the side clips engage (Figure B)

4 Snap the Trim plate into the Radio Housing. (Figure B)

1A

Technical line drawing of a mechanical housing or enclosure with mounting brackets and internal components (no text or symbols)

1B

Technical line drawing of a mechanical assembly with brackets and mounting features (no text or symbols)

A

Line drawing of a hand inserting a component into a device (no text or symbols)

B

Technical line drawing of a device chassis with labeled components (no text or symbols)

FINAL ASSEMBLY

1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recommends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
3 Reassemble radio and dash assemblies in reverse order of disassembly.

NOTE: Use the screws supplied with this kit to mount the radio housing in the vehicles that require the spacers.

FINAL WIRING CONNECTIONS

Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.

A B C D

Right Rear (+).....Violet

Right Rear (-) ..... Violet / Black

Left Rear (+).... Green

Left Rear (-) ..... Green / Black

*NOTE: When Black a wire is not present, ground radio to vehicle chassis.

All colors may not be present on all leads due to manufacturer's specifications.

99-5812 INSTRUCTIONS