99-7381 - Kit voiture Metra - Free user manual and instructions

USER MANUAL 99-7381 Metra

Interior view of a car dashboard with air filters and a digital display (no visible text or symbols)

Hyundai Santa Fe (with factory NAV) 2008-2009

KIT FEATURES

• ISO DIN radio provision with pocket
  • ISO DDIN radio provision

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8" Phillips screws • E) (4) #6 x 3/8" Phillips screws

Isometric line drawing of a rectangular frame with rounded corners and a small side label 'A' (no text or symbols on the frame itself)

Technical line drawing of two metal bracket components with mounting holes (no text or symbols)

Isometric line drawing of a rectangular electronic enclosure or housing with mounting holes (no text or symbols)

TABLE OF CONTENTS

Dash Disassembly 2

Kit Assembly

-ISO DIN radio provision with pocket ....3

-ISO DDIN radio provision ....3

WIRING & ANTENNA CONNECTIONS(sold separately)

Wiring Harness: 70-1004

Antenna Adapter: Not required

Steering Wheel Control Interface: ASWC-1

TOOLS REQUIRED

- Panel removal tool • Phillips screwdriver

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

DASH DISASSEMBLY

1. Remove (1) Phillips screw from the right side of the panel below the steering column then unclip and let right side of panel hang. (Figure A)
2. Unclip and remove the cover above the clock on top of panel surrounding the radio. (Figure B)
3. Unclip and remove the panel extending across the dash below the a/c control and above the glove box including the ash tray. (Figure C)
4. Remove (2) Phillips screws then unclip and remove the panel surrounding the radio including the A/C vents. (Figure D)
5. Remove (4) Phillips screws securing the radio. Unplug and remove radio.

Note: Illustrations shown are not actual representation of the vehicle.

Continue to Kit Assembly

Technical line drawing of a mechanical device with directional arrows indicating motion or force (no text or symbols)

(Figure A) (Figure B)

Diagram of a car interior showing airflow direction and component placement (no text or symbols)

Diagram of car air conditioning control panel with directional arrows indicating airflow or movement

Line drawing of a car dashboard and air vent system with directional arrows indicating movement (no text or symbols)

(Figure C) (Figure D)

KIT ASSEMBLY

ISO DIN radio provision with pocket

1. Attach thedio brackets to the radio trim panel using the (4) #6 x 3/8" Phillips screws provided. (Figure A)
2. Attach the pocket to the radio brackets using the (4) #8 x 3/8" Phillips screws provided. (Figure B)
3. Remove the metal DIN sleeve and trim ring from the aftermarket radio.
4. Slide the radio into the bracket/pocket assembly and then secure it using the screws supplied with the radio. (Figure C)
5. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.
6. Reassemble the dash in reverse order of disassembly.

Technical line drawing of a mechanical bracket assembly (no text or symbols)

(Figure A)

Technical line drawing of a mechanical housing or enclosure with mounting brackets and internal components (no text or symbols)

(Figure B)

Technical line drawing of a mechanical housing or enclosure with no visible text or symbols

(Figure C)

ISO DDIN radio provision

1. Attach thedio brackets to the radio trim panel using the (4) #6 x 3/8" Phillips screws provided. (Figure A)
2. Slide the radio into the bracket assembly and then secure it using the screws supplied with the radio. (Figure B)
3. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.
4. Reassemble the dash in reverse order of disassembly.

Technical line drawing of a mechanical housing or enclosure with mounting holes and structural ribs (no text or symbols)

(Figure A)

Technical diagram of an electronic device with labeled components and internal structure

(Figure B)

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.

Log onto www.installenstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians