95-7811B - Kit voiture Metra - Free user manual and instructions

USER MANUAL 95-7811B Metra

INSTALLATION INSTRUCTIONS FOR PART 95-7811

Honda Pilot 2016-up 95-7811

KIT FEATURES

• ISO DDIN radio provision
• 95-7811B - Painted matte black
• 95-7811HG - Painted gloss black

Interior view of a car dashboard with air vent grilles and a digital display (no visible text or symbols)

KIT COMPONENTS

- A) Radio trim panel • B) Radio brackets • C) (4) #8 x 3/8" Phillips screws

A

Technical line drawing of a car dashboard frame (no text or symbols)

B

C

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-1729

Antenna Adapter: • 40-HD11 • 40-HD12 (EX and higher)

Table of Contents

Dash Disassembly 2-4

Kit Assembly 5

TOOLS REQUIRED

• Panel removal tool
• Phillips screwdriver
• 10mm socket wrench with extension
  • E-12 reverse (external) Torx socket

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

95-7811

Dash Disassembly

1. Open the passenger door and remove the dash trim on the side of the dash. (Figure A)
2. Open the glove box and remove the dash trim above the opening. (Figure B)
3. Open the driver's door and remove the dash trim on the side of the dash. (Figure C)

Continued on the next page

Technical illustration of a mechanical component with an inset showing a curved blade and a lightning bolt (no text or symbols)

(Figure A) (Figure B) (Figure C)

Diagram of a car interior showing the side profile and exhaust pipe (no text or symbols)

Diagram showing light rays interacting with a curved mirror and mechanical components (no text or symbols)

95-7811

Dash Disassembly

1. Unsnap and remove the panel under the steering wheel. (Figure D)
2. Unclip and remove the hazard/airbag switch panel. (Figure E)
3. Remove (3) Phillips screws securing the climate control trim panel and then remove. (Figure F)

Continued on the next page

Technical line drawing of a mechanical component with no visible text or symbols

(Figure D) (Figure E) (Figure F

Line drawing of a car dashboard and infotainment system (no text or symbols)

Interior view of a car dashboard and steering wheel (no text or symbols visible)

95-7811

Dash Disassembly

1. Remove (2) Phillips screws securing the storage pocket and then remove. If equipped with a rear DVD player instead, remove (2) Phillips screws from the sides, and (2) E-12 reverse (external) Torx screws from the top, and then remove. (Figure G)
2. Remove the (2) upward facing 10mm bolts from the brackets on the bottom of the radio. (Figure H)
3. Unclip and remove the radio/vent assembly. (Figure I)
4. Remove the clips from the radio/vent panel (note the orientation and location of the clips, they must be installed in the same position on the new radio/vent panel).
5. Remove the (1) Phillips screw from each vent to remove, and then set aside for kit assembly.

Technical line drawing of a mechanical component with mounting holes and internal structure (no text or symbols)

(Figure G) (Figure H) (Figure I)

Top-down line drawing of a car dashboard and air vent system (no text or symbols)

Diagram of a car interior showing a mounted device with a screen and control panel (no text or symbols)

Continue to kit assembly

95-7811

Kit Assembly

1. Attach the clips removed in step 10 of dash disassembly to the same locations on the radio trim panel.
2. Attach the radio brackets to the radio trim panel using the (4) #8 x 3/8" Phillips screws provided. (Figure A)
3. Slide the radio into the completed assembly from the back, and then secure it using the screws supplied with the radio. (Figure B)
4. Attach the factory vents to the radio trim panel using the screws removed in step 11 of dash disassembly.

Technical line drawing of a car dashboard frame with mounting brackets and structural components (no text or symbols)

(Figure A)

1. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio and climate controls. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Test the radio for proper operation.
2. Reassemble the dash in reverse order of disassembly.

Technical diagram of a car air intake manifold with labeled components and directional arrows

(Figure B)

INSTALLATION INSTRUCTIONS FOR PART 95-7811

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerInstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians