95-2001C - Kit voiture Metra - Free user manual and instructions

USER MANUAL 95-2001C Metra

Close-up of a car dashboard with control knobs and a digital display (no visible text or symbols)

GM Multi Kit 1990-2012

KIT FEATURES

95-2001

• ISO DDIN radio provision
99-2001
• ISO DIN radio provision with pocket

KIT COMPONENTS

95-2001: • A1) Radio trim plate • B1) Radio brackets • C1) Spacers
99-2001: • A2) Radio trim plate • B2) Radio brackets • C2) Spacers • D2) Pocket • E2) (4) #8 x 3/8" Phillips screws

A1

E

C1

A2

• 

• 

• 

• 

APPLICATIONS

See Page 2

TABLE OF CONTENTS

See Page 3

WIRING & ANTENNA CONNECTIONS(sold separately)

Wiring Harness: Please visit metraonline.com for more information

Antenna Adapter: 40-GM10 • 40-CR10

TOOLS REQUIRED

• Phillips screwdriver • Socket set
  • Utility knife (95-2001)

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

APPLICATIONS (95-2001 OR 99-2001)

BUICK

Century 1997-2005

Le Sabre ....1995-2005

Park Avenue 1995-2005

Rainier 2004-2007

Regal....1995-2004

Rendezvous....2002-2007

Riviera....1996-1999

Roadmaster....1995-1996

Skylark 1996-1998

CADILLAC

Escalade, Escalade ESV & EXT 2003-2006

CHEVROLET

Avalanche....2003-2006

Blazer 2002-2005

Cavalier 2000-2005

Colorado 2004-2012

Express Van (full size) ......2001-2007

CHEVROLET (CONT)

Impala....2000-2005

Kodiak....2003-2009

Malibu 2001-2003

Malibu Classic 2004-2005

Monte Carlo 2000-2005

S-10

(with ISO DDIN radio) .....2002-2004

Silverado....2003-2006

Silverado Classic 2007

Suburban....2003-2006

Tahoe 2003-2006

Trailblazer 2002-2009

Venture 2000-2005

GMC

Canyon 2004-2012

Envoy 2002-2009

Savanna....2001-2007

GMC (CONT)

Sierra....2003-2006

Sierra Classic 2007

Sonoma

(with ISO DDIN radio) .....2002-2004

TopKick....2005-2009

Yukon....2003-2006

HUMMER

H2....2003-2007

ISUZU

Ascender....2003-2008

H-Series 2003-2008

1-290/1370 2007-2008

1-280/1350....2006

OLDSMOBILE

Achieva 1996-1998

Alero....1999-2004

OLDSMOBILE (CONT)

Aurora....1995-2003

Bravada....1998-2004

Cutlass....1997-1999

Cutlass Supreme 1995-1997

Eighty-Eight 1994-1999

Intrigue....1998-2002

LSS....1996-1999

Ninety-Eight....1994-1996

Regency 1997-1998

Silhouette 2000-2004

PONTIAC

Aztec 2001-2005

Bonneville.... 2000-2005

Grand Am 2001-2005

Montana....2000-2005

Sunfire 2000-2005

TABLE OF CONTENTS

Dash Disassembly

• Buick Century 1997-2005 ....4
• Buick Le Sabre 1995-2005 ....4
• Buick Park Avenue 1995-2005 4
• Buick Rainier 2004-2007 ....13
• Buick Regal 1995-2004....4
• Buick Rendezvous 2002-2007 ....5
• Buick Riviera 1996-1999 ....5
• Buick Roadmaster 1995-1996 ....6
• Buick Skylark 1996-1998 6
• Cadillac Escalade, Escalade ESV & EXT 2003-2006 ....7
• Chevrolet Avalanche 2003-2006 ....7
• Chevrolet Blazer 2002-2005 7
• Chevrolet Cavalier 2000-2005 8
• Chevrolet Colorado 2004-2008 ....8
• Chevrolet Express Van (full size) 2001-2002 ....9
• Chevrolet Express Van (full size) 2003-2007 ....9
• Chevrolet Impala 2000-2005 ....10
• Chevrolet Kodiak 2003-2009 7
• Chevrolet Malibu 2001-2003 ....10
• Chevrolet Malibu Classic 2004-2005 ....10

• Chevrolet Monte Carlo 2000-2005 ....10

• Chevrolet S-10 (with ISO DDIN radio) 2002-2004 ....7

• Chevrolet Silverado/Classic 2003-2007 7
• Chevrolet Suburban 2003-2006 7
• Chevrolet Tahoe 2003-2006 7
• Chevrolet Trailblazer 2002-2009 ....11
• Chevrolet Venture 2000 ....11
• Chevrolet Venture 2001-2005 ....12
• GMC Canyon 2004-2008 ....8
• GMC Envoy 2002-2007....13
• GMC Savanna 2001-2002 ....8
• GMC Savanna 2003-2007 9
• GMC Sierra/Classic 2003-2007 7
• GMC Sonoma (with ISO DDIN radio) 2002-2004 ....7
• GMC TopKick 2005-2009 7
• GMC Yukon/Denali/XL 2003-2006 ....7
• Hummer H2 2003-2007 ....14
• Isuzu Ascender 2003-2005 ....13
• Isuzu H-Series 2003-2008 7
• Isuzu I-290/1370 2007-2008 8
• Isuzu I-280/I350 2006....8

• Oldsmobile Achieva 1996-1998 ....15

• Oldsmobile Alero 1999-2004 ....15

• Oldsmobile Aurora 1995-2003 ....15
• Oldsmobile Bravada 1998-2001 7
• Oldsmobile Bravada 2002-2004 ....13
• Oldsmobile Cutlass 1997-1999 ....16
• Oldsmobile Cutlass Supreme 1995-1997 ....13
• Oldsmobile Eighty-Eight 1994-1999 ....16
• Oldsmobile Intrigue 1998-2002....16
• Oldsmobile LSS 1996-1999 ....17
• Oldsmobile Ninety-Eight 1994-1996 ....16
• Oldsmobile Regency 1997-1998 ....17
• Oldsmobile Silhouette 2000....11
• Oldsmobile Silhouette 2001-2004 ....12
• Pontiac Aztec 2001-2005 ....17
• Pontiac Bonneville 2000-2005....17
• Pontiac Grand Am 2001-2005 ....18
• Pontiac Montana 2000 (Except SV6)....11
• Pontiac Montana 2001-2005 (Except SV6)....12
• Pontiac Sunfire 2000-2005 ....18

Kit Assembly....19

DASH DISASSEMBLY 95-2001 OR 99-2001

Buick Century 1997-2005

Buick Regal 1995-2004

1. Remove the plastic trim piece to the left of the glove box and (1) Phillips screw exposed.
2. Unsnap the top edge of the knee bolster panel.
3. Remove (1) Phillips screw from the panel.
4. Remove the ashtray cluster and (2) Phillips screws from each side.
5. Unclip the entire dash trim bezel and remove.
6. Open doors and unsnap end caps from each side of dash.
7. Unsnap and remove radio/instrument cluster panel.
8. Remove (3) screws in order to remove radio.

Buick Le Sabre/Buick Park Avenue 1995-1999

1. Unsnap the climate control trim panel (from door to door) and remove (4) Phillips screws exposed. (Figure A)
2. Pop out the a/c vents and remove (1) Phillips screw exposed in each vent cavity. (Figure A)
3. Unclip the radio trim bezel and remove.
4. Remove the screws securing the factory radio and disconnect the wiring.

Continue to Kit Assembly

Buick Le Sabre/Buick Park Avenue 2000-2005

1. Open drivers door and unsnap and remove dash end cap.
2. Unsnap and remove trim along center of dash (one piece on right and one on left of wheel).
3. Unsnap and remove radio/instrument bezel.
4. Remove (2) screws in order to remove radio.

Note: For the Buick LeSabre, (3) speed clips and screws will need to be supplied to attach the kit into the sub-dash where the screw holes line up with the kit.

Continue to Kit Assembly

Continue to Kit Assembly

Line drawing of a mechanical component with no visible text or symbols

(Figure A)

Technical diagram of a device with numbered components, likely an electronic or mechanical assembly.

(Figure A)

Technical line drawing of two mechanical components with no visible text or symbols

(Figure A)

DASH DISASSEMBLY 95-2001 OR 99-2001

Buick Rendezvous 2002-2007

1. Open center console and remove (2) screws at front of console opening. (Figure A)
2. Remove liners from cup holders and storage pocket next to cup holders, then remove screws. Unsnap and remove panel. (Figure B)
3. Remove (2) screws from bottom of radio/climate control bezel, unclip and remove. (Figure C)
4. Remove (3) 9/32" hex-head screws to remove radio. (Figure D)

Continue to Kit Assembly

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figure A)

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figure B)

Simple line drawing of a car's side panel with arrows indicating movement (no text or symbols)

(Figure C)

Simple line drawing of a person standing beside a computer monitor with a screen (no text or symbols)

(Figure D)

Buick Riviera 1996-1999

1. Unsnap left side panel exposing (1) Phillips screw to remove.
2. Remove (1) Phillips screw and unsnap right side panel to expose (1) Phillips screw beneath panel and remove.
3. Unsnap underside of overhanging dash to unsnap (6) plastic rivets and remove panel.

4. Remove (5) hex-head screws now exposed under overhang.

5. Unsnap bottom edge of trim bezel, then while holding overhang up, unsnap and remove trim bezel by removing any necessary harnesses.

6. Remove (3) Phillips screw to remove climate control.
7. Remove (2) Phillips screws to remove rear support and (3) 9/32"
   Continue to Kit Assembly

Step 1 Step 2 Step 3 Step 4

(Figure A)

DASH DISASSEMBLY 95-2001 OR 99-2001

Buick Roadmaster 1995-1996

1. Unclip dash panel sides and remove.
2. Unclip panel below steering column and remove.
3. Remove (2) 7mm screws above instrument cluster.
4. Set parking brake, turn car on, and move shifter to the lowest gear. Tilt steering wheel down then unsnap entire instrument cluster/radio panel and remove.
5. Remove (3) 7mm screws to remove radio.

Continue to Kit Assembly

Step 1 Step 2 Step 3 Step 5

(Figure A)

Buick Skylark 1996-1998

1. Remove (6) 9/32" screws inside glove box.
2. Under glove box and drivers knee bolster, remove (2) plastic panels by turning (2) 1/4 turn fasteners per side.
3. Remove (4) 9/32" screws revealed (2 per side).
4. Unsnap panel from driver's side to passenger's side.
5. Remove (3) 9/32" screws.

Continue to Kit Assembly

Step 1 Step 1 Step 3 Step 3 Step 1 Step 3 Step 1 Step 5

(Figure A)

DASH DISASSEMBLY 95-2001 OR 99-2001

Cadillac Escalade, Escalade ESV & EXT 2003-2006, Chevrolet Avalanche/Suburban/Tahoe 2003-2006, Chevrolet Kodiak 2003-2009, Chevrolet Silverado/Classic 2003-2007, GMC Sierra/Classic 2003-2007, GMC TopKick 2003-2009, GMC Yukon/Denali/XL 2003-2006, Isuzu H-Series 2003-2008

1. Unsnap and remove dash bezel.
2. Remove (3) 9/32" screws and remove radio.

Continue to Kit Assembly

Chevrolet Blazer 2002-2005, S-10/GMC Sonoma (with ISO DDIN radio) 2002-2004, Oldsmobile Bravada 1998-2001

1. Remove (2) 9/32" hex-head screws from the knee bolster panel.
2. Pull down on the panel and remove the 9/32" hex-head screws exposed on the bottom of the dash trim bezel.
3. Remove (1) Phillips screw above the instrument cluster.
4. Unclip the dash trim bezel and remove.
5. Remove (2) 9/32" hex-head screws securing the factory head unit and disconnect the wiring.

Continue to Kit Assembly

Technical line drawing of a vehicle chassis with two views (front and side), showing internal components without any text or symbols.

(Figure A)

Technical line drawing of a vehicle air intake manifold assembly (no text or symbols)

(Figure A)

DASH DISASSEMBLY 95-2001 OR 99-2001

Chevrolet Cavalier 2000-2005

1. Open drivers door and remove fuse panel on end of dash.
2. Open passenger door and remove panel on end of dash.
3. Remove (1) Phillips screw from each side exposed.
4. Remove (3) screws from top of glove box liner.

5. Remove (2) screws from the top-left corner of the glove box cavity.

6. Remove (1) Phillips screw from the defroster duct.

7. Remove the ductwork and (1) Phillips screw exposed.
8. Remove the dash pad and (3) Phillips screws exposed at the top of the radio trim bezel.

Continue to Kit Assembly

Chevrolet Colorado 2004-2008, GMC Canyon 2004-2008, Isuzu I-290/I-370 2007-2008, Isuzu I-280/I-350 2006

1. Unsnap and remove the entire panel surrounding the radio and A/C controls. (Figure A)
2. Remove (3) 9/32" screws securing the radio to remove. (Figure B)

Continue to Kit Assembly

Interior view of a car dashboard with hand operating controls (no visible text or symbols)

(Figure A) (Figure B)

Line drawing of a car interior showing the dashboard and air vent (no text or symbols)

DASH DISASSEMBLY 95-2001 OR 99-2001

Chevrolet Express Van 2001-2002, GMC Savanna 2001-2002

1. Unsnap and remove small trim panel below steering column. (Figure A)
2. Unsnap radio/climate/instrument panel. (Figure B)
3. Move shift lever to first gear position.
4. Rotate panel counterclockwise to lift over steering column and remove.
5. Remove (3) 9/32" hex-head screws to remove radio.

Continue to Kit Assembly

Line drawing of a car interior showing steering wheel, dashboard, and steering wheel (no text or symbols)

(Figure A)

Diagram of a car dashboard with steering wheel and air vent (no text or labels)

(Figure B)

Chevrolet Express Van 2003-2007, GMC Savanna 2003-2007

1. Remove (2) 10mm bolts from below knee bolster under steering column and remove panel. (Figure A)
2. Remove (2) 10mm bolts from panel below passenger dash airbag and remove panel. (Figure B)
3. Remove (2) 10mm nuts from inside center pocket between power outlets. (Figure C)
4. Unsnap and remove radio and instrument cluster panel. (May not be necessary to completely remove radio and instrument cluster panel to access radio.)
5. Remove (3) 9/32" bolts to remove radio.

Continue to Kit Assembly

Front view of a car dashboard with steering wheel and control panel (no text or symbols visible)

(Figure A)

Line drawing of a car front panel and side door (no text or symbols)

(Figure B)

Line drawing of a car dashboard with front panel, backrest, and control buttons (no text or symbols)

(Figure C)

DASH DISASSEMBLY 95-2001 OR 99-2001

Chevrolet Impala 2000-2005

1. Unclip each side of the dash trim bezel (fuse access) and remove (1) Phillips screw exposed on each side.
2. Remove (2) Phillips screws under the instrument cluster.
3. Unclip the trim panel above the pedals. (It is not necessary to remove the panel it can be left hanging).
4. Remove (2) Phillips screws from the knee panel.
5. Unclip the knee panel and remove (1) Phillips screw exposed on the right side of the steering column.
6. Unclip and remove the entire dash trim bezel.

Continue to Kit Assembly

Technical line drawing of two mechanical components with ventilation grilles (no text or symbols)

(Figure A)

Chevrolet Malibu 2001-2003, Chevrolet Malibu Classic 2004-2005

1. Unsnap and remove radio bezel.
2. Remove (3) bolts and remove radio.

Continue to Kit Assembly

Technical diagram of a car dashboard with labeled parts including front panel, rear panel, and control panel

(Figure A)

Chevrolet Monte Carlo 2000-2005

1. Unclip the trim panel above the pedals. (It is NOT necessary to remove the panel it may be left hanging.)
2. Remove (2) 9/32" screws from the knee panel and unclip the panel.
3. Unsnap the driver's side fuse panel cover and remove (1) 9/32" screw.
4. Open the glove box and remove (1) 9/32" screw from the upper left corner.
5. Remove (3) 9/32" screws securing the factory radio and disconnect the wiring.

Continue to Kit Assembly

Technical line drawing of two mechanical component parts (no text or symbols)

(Figure A)

DASH DISASSEMBLY 95-2001 OR 99-2001

Chevrolet Trailblazer 2002-2009

1. Remove (2) Phillips screws inside instrument cluster.
2. Remove (1) Phillips screw under climate controls to the left of the power outlet.
3. Remove (2) 7mm hex-heads from under steering column and lower the panel. Remove (3) Phillips screws around steering wheel.
4. Unsnap and remove bezel. (Use caution pulling over hazard switch.) Remove (3) 7mm hexhead screws to remove radio.

Continue to Kit Assembly

Step 1 Step 2 Step 3 Step 1 Step 2 Step 3

(Figure A)

Chevrolet Venture 2000, Oldsmobile Silhouette 2000, Pontiac Montana 2000 (Except SV6)

1. Remove the ashtray and (1) Phillips screw exposed in the ashtray cavity.
2. Remove (1) Phillips screw from the cigarette lighter compartment.
3. Remove (2) Phillips screws securing the factory radio and disconnect the wiring.

Continue to Kit Assembly

Technical line drawing of two mechanical components with mounting holes and housing (no text or symbols)

(Figure A)

DASH DISASSEMBLY 95-2001 OR 99-2001

Chevrolet Venture 2001-2005, Oldsmobile Silhouette 2001-2004 Pontiac Montana 2001-2005 (Except SV6)

1. Open cup holders and remove (2) Phillips 7mm screws. (Figure A)
2. Unsnap and remove dual power outlet assembly from lower storage.
3. Open lower storage door and remove (2) 7mm screws inside.
4. Models with DVD - Remove DVD player and remove (2) 7mm screws from behind and (2) 7mm screws near the floor.
5. Remove lower storage compartment. (Figure B)
6. Remove (2) 7mm screws (facing up) from under cup holder. (Figure C)
7. Remove (3) 7mm hex-head screws and remove radio.

Continue to Kit Assembly

Line drawing of a hand inserting a device into a rack (no text or symbols)

(Figure A) (Figure B)

Pure mechanical component outline without any text, numbers, or symbols

Line drawing of a vehicle air conditioner unit with no text or symbols

Technical line drawing of a mechanical component or bracket (no text or symbols)

(Figure C) (Figure D)

DASH DISASSEMBLY 95-2001 OR 99-2001

GMC Envoy 2002-2007, Isuzu Ascender 2003-2005, Oldsmobile Bravada 2002-2004, Buick Ranier 2004-2007

1. Remove (4) Phillips screws, (2) from left and (2) from right of carpeted panel. (Figure A)
2. Slide carpeted panel down and backwards to reveal (2) Phillips screws and remove. (Figure B)
3. Unsnap radio bezel and unplug cigarette lighter and accessories. (Figure C)
4. Remove (3) screws and remove radio. (Figure C)

Continue to Kit Assembly

Diagram of a car air intake console with directional arrows indicating airflow or movement (no text or symbols)

(Figure A) (Figure B) (Figure C)

Line drawing of a car air intake console with buttons and dials (no text or symbols)

Line drawing of a car air intake console with buttons and dials (no text or symbols)

Diagram of a car air intake system showing two components with directional arrows indicating flow or movement (no text or labels present)

DASH DISASSEMBLY 95-2001 OR 99-2001

Hummer H2 2003-2007

1. Open center console and remove (4) 9/32" screws from console box and remove box. (Figure A)
2. Remove (4) Phillips screws from hinge on console door inside console and remove door. (Figure B)
3. Loosen (1) T-15 torx on forward facing side of shift lever and pull up to remove. (Figure C)

4. Unclip cup holder/shifter trim assembly and remove. (Figure D)

5. Remove (6) Phillips screws from top of center console. (Figure F)

6. Remove (2) Phillips screws from inside pocket on back of center console, then unclip and remove.
7. Remove (1) 10mm bolt to right of shift lever. (Figure E)

8. Remove (2) Phillips screws from under console box on drivers side and (2) Phillips screws from under console trimtop on passenger side. (Figure F)

9. Slide control assembly rearwards. (Figure F)

10. Remove (2) T-30 torx bolts from top of rado/climate control trim and unclip and remove. (Figure G)
11. Remove (3) 9/32" screws that hold the radio in. (Figure G)

Continue to Kit Assembly

Pure mechanical component diagram without any text, numbers, or symbols

(Figure E) (Figure F)

Step 8 Step 9 Step 5

Step 1

(Figure A) (Figure B) (Figure C) (Figure D)

Step 2 0 0 0 0 0 0

Step 3

Step 4

Technical line drawing of a car air intake system with no visible text or symbols

(Figure G)

DASH DISASSEMBLY 95-2001 OR 99-2001

Oldsmobile Achieva 1996-1998

1. Open the glove box, press inward on the walls of the glove box liner and remove the liner.
2. Remove (10) torx-head screws from the glove box location.
3. Remove (2) 9/32" hex-head screws under the steering column.
4. Unclip the dash trim bezel. (Figure A)
5. Remove the screws securing the factory radio and disconnect the wiring.

Continue to Kit Assembly

Technical line drawing of a mechanical component with two views (no text or symbols)

(Figure A)

Oldsmobile Alero 1999-2004

1. Remove shift knob by using a small screwdriver to remove U-clip from front of shifter and pull upward.
2. Unclip and remove shifter trim panel.
3. Unclip and remove radio and climate control panel by pulling from bottom. (Figure A)
4. Remove (3) 9/32" screws from radio and remove.

Continue to Kit Assembly

Line drawing of hands operating a control panel with display screens (no text or symbols)

(Figure A)

Oldsmobile Aurora 1995-2003

1. Unclip the radio trim bezel and remove the bezel. (Figure A)
2. Remove (2) 7mm screws securing the factory radio and disconnect the wiring.

Note: For the 2001-2003 models,(3) speed clips and screws will need to be supplied to attach the kit into the sub-dash where the screw holes line up with the kit.

Continue to Kit Assembly

Line drawing of a car interior compartment showing fan, door, and vent (no text or symbols)

(Figure A)

DASH DISASSEMBLY 95-2001 OR 99-2001

Oldsmobile Cutlass 1997-1999, Oldsmobile Cutlass Supreme 1995-1997

1. Unclip the radio trim bezel and remove. (Figure A)
2. Remove (2) 9/32" hex-head screws securing the factory radio and disconnect the wiring.

Continue to Kit Assembly

Technical line drawing of two mechanical components with no visible text or symbols

(Figure A)

Oldsmobile Eighty-Eight 1994-1999

1. Unclip the radio trim bezel and remove.
2. Remove (2) 9/32" hex-head screws securing the factory radio and disconnect the wiring.

Continue to Kit Assembly

Oldsmobile Ninety-Eight 1994-1996

1. Open the glove box and remove (2) hex-head screws securing the wood trim.
2. Unsnap the wood trim and remove.
3. Remove (2) hex-head screws below the radio trim bezel.
4. Lift up on the bezel and remove.
5. Remove (3) Phillips hex-head screws securing the factory radio and disconnect the wiring.

Continue to Kit Assembly

Technical line drawing of two mechanical components with no visible text or symbols

(Figure A)

Oldsmobile Intrigue 1998-2002

1. Open the center console storage compartment and remove (2) 9/32" hex-head screws exposed.
2. Remove the center console.
3. Unclip the radio trim bezel and remove.
4. Remove (2) 9/32" hex-head screws securing the factory radio and disconnect the wiring.

Continue to Kit Assembly

Line drawing of a chair and a mechanical device (no text or symbols)

(Figure A)

DASH DISASSEMBLY 95-2001 OR 99-2001

Oldsmobile LSS 1996-1999 / Regency 1997-1998

1. Open glove box and remove two-center trim bezels attached by screws. (Figure A)
2. Unsnap and remove radio trim bezel. (Figure A)
3. Remove (3) 9/32" hex-head screws and remove radio. (Figure B)

Continue to Kit Assembly

Step 1 Step 2 Step 1

(Figure A)

Step 3

(Figure B)

Pontiac Aztec 2001-2005

1. Pull out cup holder inserts.
2. Remove (1) Phillips screw exposed inside bottom cup holder.
3. Unsnap and remove shifter trim with cup holders.
4. Remove (2) #15 torx at bottom of radio/climate bezel.

Continue to Kit Assembly

Technical line drawing of two mechanical components (no text or symbols)

(Figure A)

Pontiac Bonneville 2000-2005

1. Remove (2) Phillips screws from the instrument cluster. (Figure A)
2. Unclip the ignition trim and remove. (Figure B)
3. Unclip the climate control/radio trim bezel and remove.

Pontiac Bonneville 2000-2005 (CONT)

1. Depress the spring clips on each side of the factory head unit and remove. (Figure C)

Note: (3) speed clips and screws will need to be supplied to attach the kit into the sub-dash where the screw holes line up with the kit.

Continue to Kit Assembly

Line drawing of a car dashboard with two directional arrows indicating movement or force (no text or symbols)

Interior view of a car dashboard with steering wheel and dashboard (no text or symbols visible)

(Figure A) (Figure B)

Diagram of a device panel with directional arrows indicating orientation (no text or symbols)

(Figure C)

DASH DISASSEMBLY 95-2001 OR 99-2001

Pontiac Grand Am 2001-2005

1. Unsnap and remove radio trim bezel. (Figure A)
2. Remove (3) 9/32" screws from radio brackets and remove radio. (Figure A) Continue to Kit Assembly

Technical line drawing of a car dashboard and its internal components (no text or symbols)

(Figure A)

Pontiac Sunfire 2000-2005

1. Open the glove box and remove (2) Phillips screws exposed on the right edge of the radio trim bezel.
2. Unclip the bezel and remove.
3. Remove (2) 7mm hex-head screws securing the factory head unit and disconnect the wiring.

Continue to Kit Assembly

Technical line drawing of a mechanical housing component (no text or symbols)

(Figure A)

KIT ASSEMBLY

ISO DDIN radio provision (95-2001):

1. Attach the radio brackets to the inside edge of the radio trim plate. (Figure A)
2. Slide the radio into the completed assembly, and then secure the radio to the assembly using the screws supplied with the radio. (Figure B)
3. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.
4. Reassemble the dash in reverse order of disassembly.

Note: The spacers included in the kit may be necessary to adapt to the slight differences from one vehicle to another. If the kit/radio assembly does not meet the backside of the factory radio opening, use the spacers to eliminate that space.

Isometric line drawing of a two-framed rectangular frame with directional arrows indicating movement or force (no text or symbols)

(Figure A) (Figure A)

Technical line drawing of an electronic device with internal components and directional arrows indicating flow or movement (no text or symbols present)

(Figure B) (Figure B)

ISO DIN radio provision with pocket (99-2001):

1. Attach the radio brackets to the inside edge of the radio trim plate. (Figure A)
2. Slide the pocket into the assembly, and then secure using the (4) #8 x 3/8" Phillips screws provided. (Figure B)
3. Remove the metal DIN sleeve and trim ring from the aftermarket radio.
4. Slide the radio into the bracket/pocket assembly, and then secure using the screws supplied with the radio. (Figure B)
5. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.
6. Reassemble the dash in reverse order of disassembly.

Note: The spacers included in the kit may be necessary to adapt to the slight differences from one vehicle to another. If the kit/radio assembly does not meet the backside of the factory radio opening, use the spacers to eliminate that space.

Diagram of a rectangular device with internal components and directional arrows indicating flow or movement (no text or symbols)

Technical line drawing of a device casing with labeled ports and components (no text or symbols)

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.

Log onto WWW.installentInstitute.com or Call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

INST-2001 Addendum

For the Buick LeSabre, Oldsmobile Aurora, and Pontiac Bonneville, the (3) speed clips and screws provided will attach the kit into the sub-dash where the screw holes line up with the kit.