99-8910S - Kit voiture Metra - Free user manual and instructions

USER MANUAL 99-8910S Metra

Interior view of a car dashboard with a digital display showing the powertrain (no visible text or symbols on screen)

Nissan Sentra 2020-Up

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications

KIT FEATURES

• ISO DDIN radio provision †
- Pioneer modular DDIN radio provision †
- Painted with a gloss black face, silver trim, and a textured housing.

This kit can only be used with an ISO DDIN radio with an "L" shaped chassis design, with the radio chassis at the bottom of the screen. As of this writing, only the Alpine INE-W967HD (discontinued, replaced by INE-W977HD), iLX-107, and iLX-207 have this design. Also, The Pioneer modular radios, DMH-C2550NEX and DMH-C2500NEX, can also be used with the included adapter brackets.

KIT COMPONENTS

• A) Radio housing (front) • B) Radio housing (rear) • C) Radio trim panel • D) Radio brackets • E) Pioneer adapter brackets
• F) #4 x 3/8" Phillips screws (4) • G) #6 x 3/8" Phillips screws (4) • H) Panel clips (3)

TABLE OF CONTENTS

Dash Disassembly 2

Kit Assembly

- ISO DDIN radio provision 3-4

- Pioneer modular DDIN radio provision......5-6

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: 70-7552

Antenna Adapter: 40-N112

TOOLS REQUIRED

• Panel removal tool
• Phillips screwdriver
• 10mm socket wrench

Attention! Let the vehicle sit with the key out of the ignition for a few minutes before removing the factory radio. When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition.

DASH DISASSEMBLY

1. Unclip and remove the trim panel behind the radio. There are (4) clips securing this panel to the dash. Use caution as the front of the trim panel can easily be damaged. (Figure A)

Note: Dash vents may vary depending on Nissan model.

1. Remove (4) 10mm screws securing the radio. Take note that the lower radio brackets are angled inward, hiding the bottom (2) screws from being easily seen. Slide the radio out, then unplug and remove the radio. (Figure B)

Continue to Kit Assembly

Diagram of a car interior showing the steering wheel, dashboard, and seatbelt mechanism (no text or labels)

(Figure A) (Figure B)

Interior view of a car dashboard with a monitor and keyboard, showing directional arrows indicating movement or assembly (no text or symbols present)

KIT ASSEMBLY

ISO DDIN radio provision

1. Attach (3) panel clips provided onto the radio housing (front). (Figure A)
2. Snap the radio housing (front) to the radio housing (rear), then secure using (4) #4 x 3/8" Phillips screws provided (Figure B)
3. Secure the radio brackets to the radio housing using (4) #6 x 3/8" Phillips screws provided. (Figure C)

Technical line drawing of a rectangular frame with dashed lines indicating alignment or projection (no text or symbols)

(Figure A) (Figure B) (Figure C)

Technical line drawing of two mechanical components with directional arrows indicating movement or force (no text or symbols)

Technical line drawing of a mechanical component with two views and alignment arrows (no text or symbols)

Continued on the next page

KIT ASSEMBLY (CONT.)

1. Slide the radio into the radio housing assembly through the front, then secure it to the assembly using screws supplied with the radio. (Figure D)
2. Clip the radio trim panel onto the radio housing assembly. (Figure E)
3. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.
4. Secure the radio assembly to the dash using the factory screws.
5. Snap the factory trim panel to the dash to complete the installation.

Technical line drawing of an automotive air conditioner unit with mounting holes and internal panel (no text or symbols)

(Figure D) (Figure E)

Technical line drawing of a device housing with a panel and mounting bracket (no text or symbols)

KIT ASSEMBLY

Pioneer Modular DDIN radio provision

Note: For steps 4 and 5, reference the installation manual provided with the radio for which hardware to use. The display screen and radio chassis use two different types of screws.

1. Attach (3) panel clips provided onto the radio housing (front). (Figure A)
2. Snap the radio housing (front) to the radio housing (rear), then secure using (4) #4 x 3/8" Phillips screws provided (Figure B)

Isometric line drawing of a rectangular frame with dashed lines indicating hidden edges (no text or symbols)

1. Secure the radio brackets to the radio housing using (4) #6 x 3/8" Phillips screws provided. (Figure C)
2. Secure the radio display to the Pioneer adapter brackets using (6) screws supplied with the radio. (Figure D)

Continued on the next page

Technical illustration of a mechanical component with two views and a directional arrow (no text or symbols)

(Figure C)(Figure A)

Technical line drawing of two mechanical components with arrows indicating motion or assembly (no text or symbols)

Technical line drawing of a mechanical assembly with two vertical supports and dashed alignment lines (no text or symbols)

(Figure D)(Figure B)

KIT ASSEMBLY (CONT.)

1. Secure the display and bracket assembly to the radio chassis using (4) screws supplied with the radio. (Figure E)
2. Slide the radio assembly into the radio housing assembly through the front, then secure it to the assembly using screws supplied with the radio. (Figure F)
3. Clip the radio trim panel onto the radio housing assembly. (Figure G)

3D technical illustration of a mechanical or electronic component with mounting holes and a central housing (no text or symbols visible)

(Figure E)

1. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.
2. Secure the radio assembly to the dash using the factory screws.
3. Snap the factory trim panel to the dash to complete the installation.

Technical line drawing of two electronic components with a close-up view of their internal structure (no text or symbols)

(Figure G)

Technical line drawing of a mechanical component with no visible text or symbols

(Figure F)

If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 386-257-1187, or email at [e-mail]. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

Pioneer Sun Integrated DVD 6

Exterior view of a black plastic automotive enclosure with side brackets and mounting feet (no text or symbols)

HARDWARE INCLUDED

Illustration of screw and nut components with various thread configurations (no text or symbols)

Nissan Sentra 2020-Up

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications.

ISO DDIN radio provision ^+

Pioneer modular DDIN radio provision

Painted with a gloss black face, silver trim, and a textured housing.

^ This kit can only be used with an ISO DDIN radio with an "L" shaped chassis design, with the radio chassis at the bottom of the screen. As of this writing, only the Alpine INE-W967HD (discontinued, replaced by INE-W977HD), iLX-107, and iLX-207 have this design. Also, The Pioneer modular radios, DMH-C2550NEX and DMH-C2500NEX, can also be used with the included adapter brackets.

KIT COMPONENTS

• Radio housing (front)
• Radio housing (rear)
• Radio trim panel
• Radio brackets
• Pioneer adapter brackets

• 4 x 3/8" Phillips screws (4)

• 6 x 3/8" Phillips screws (4)

• Panel clips (3)

WIRING & ANTENNA CONNECTIONS

(sold separately)

• Wiring Harness: 70-7552
- Antenna Adapter: 40-NI12

SALES 800-221-0932