95-7419 - Kit voiture Metra - Free user manual and instructions

USER MANUAL 95-7419 Metra

INSTALLATION INSTRUCTIONS FOR PART 95-7419

APPLICATIONS

Nissan Altima

2005-2006

(Without factory navigation)

95-7419

KIT FEATURES

• Double DIN Head Unit Provision
- Stacked ISO DIN Head Unit Provision

KIT COMPONENTS

Interior view of a car dashboard with a mounted touchscreen display (no visible text or symbols)

A

TOOLS REQUIRED:

Phillips Screwdriver • Small Flat Blade Screwdriver

1-800-221-0932

www.metraonline.com

© COPYRIGHT 2004-08 METRA ELECTRONICS CORPORATION

TABLE OF CONTENTS

Dash Disassembly 1

Kit Assembly 2,3

Final Assembly 4

2005-06 NISSAN ALTIMA

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove the trim panel surrounding the climate controls. (Figure A)
3 Remove (4) Phillips screws securing climate control and remove. (Figure B)
4 Unclip and remove the panel surrounding radio including A/C vents. (Figure C)
5 Remove (4) Phillips screws securing radio to remove. (Figure D)

D

Illustration of a hand inserting cable into a device panel with arrows indicating motion (no text or symbols)

A

1 2 3 AU/DO CLOCK 4 5 6 SCN CJ-IPPT

B

1 2 3 AUDIO CLOCK 4 5 6 SCAN CAT-RPT AUTO OFF AUTO A/C AUTO

C

Line drawing of a car air conditioner unit with hand holding tool (no text or symbols)

2005-06 NISSAN ALTIMA

DOUBLE DIN HEAD UNIT PROVISION

1 Snap the 95-7419 trim plate into the radio trim panel. (Figure A)
2 Slide the DDIN radio unit into the factory brackets and secure the unit to the brackets using the screws supplied with the head unit. (Figure B)

A

Install the 95-7419 Trim Plate from Rear

B

Illustration of a hand using a tool to adjust or install a mechanical component (no text or symbols visible)

2005-06 NISSAN ALTIMA

STACKED ISO DIN HEAD UNIT PROVISION

1 Snap the 95-7419 trim plate into the radio trim panel. (Figure A)
2 Slide the stacked ISO DIN units into the factory brackets and secure the units to the brackets using the screws supplied with the head units. (Figure B)

A

Install the 95-7419 Trim Plate from Rear

B

Illustration of a hand using a screwdriver to adjust or install a device from a computer case (no text or symbols visible)

FINAL ASSEMBLY

A B C D

1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown.

(Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)

2 Re-connect the negative battery terminal and test the unit for proper operation.
3 Reassemble radio and dash assemblies in reverse order of disassembly.

FINAL WIRING CONNECTIONS

Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE

12V Ignition / Acc ... Red

Right Front (+) ..... Gray

12V Batt / Memory .. Yellow

Right Front (-)..... Gray / Black

Ground .... Black*

Left Front (+) ..... White

Power Antenna ..... Blue

Left Front (-) ..... White / Black

Amp Turn-On ..... Blue / White

Right Rear (+).....Violet

Amp Ground ..... Black / White

Right Rear (-) ..... Violet / Black

Illumination.....Orange

Left Rear (+).... Green

Dimmer ..... Orange / White

Left Rear (-) ..... Green / Black

*NOTE: When Black a wire is not present, ground radio to vehicle chassis.

All colors may not be present on all leads due to manufacturer's specifications.

NOTES

95-7419