99-7330 - Kit voiture Metra - Free user manual and instructions
Find the device manual for free 99-7330 Metra in PDF.
User questions about 99-7330 Metra
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Kit voiture in PDF format for free! Find your manual 99-7330 - Metra and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 99-7330 by Metra.
USER MANUAL 99-7330 Metra
INSTALLATION INSTRUCTIONS FOR PART 99-7330
APPLICATIONS
KIA Spectra/Spectra 5 2007-2009
99-7330
KIT FEATURES
• Recessed DIN Mount Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
natural_image
Interior view of a car dashboard with air conditioners and gauges (no visible text or symbols)KIT COMPONENTS
natural_image
Isometric technical drawing of a mechanical bracket assembly (no text or symbols)
natural_image
Technical line drawing of two mechanical bracket components labeled B (no text or symbols on the brackets)
WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness:
• 70-1004 - Hyundai 2006-up/KIA harness 2004-up
Antenna Adapter:
- Not required
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2007-2009
www.metraonline.com
METRA ELECTRONICS CORPORATION
TABLE OF CONTENTS
Dash Disassembly
- KIA Spectra/Spectra 5 2007-2009 ....1
Kit Assembly
- DIN Mount Radio Provision with Pocket 2
- ISO Mount Radio Provision with Pocket .... 3
Final Assembly 4
*Note:
Refer also to the instructions included with the aftermarket radio.
text_image
INSTALLER INSTITUTEKNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.
Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
KIA SPECTRA/SPECTRA 5 2007-2009
1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove the trim panel surrounding the radio and including the a/c vents. (Figure A)
3 Remove (4) Phillips screws securing the radio. Unplug and remove radio. (Figure B)
Continue to kit assembly.
natural_image
Interior view of a car showing the dashboard and air vent (no text or symbols visible)
text_image
BRECESSED DIN MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A)
2 Slide the aftermarket radio into the DIN cage/housing assembly until it snaps into place. (Figure B)
Continue to final assembly.
natural_image
Line drawing of a hand using a screwdriver to adjust or install a mechanical component (no text or symbols visible)
natural_image
Technical line drawing of a mechanical device with no visible text or symbolsISO MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
1 Align the holes from the ISO snap in brackets with the holes in the side of the radio and mount the brackets to the radio using screws supplied with the radio. (Figure A)
2 Slide the radio/bracket assembly into the radio housing until the assembly snaps into place. (Figure B)
3 Snap the ISO trim plate onto the radio and housing assembly. (Figure B)
Continue to final assembly.
natural_image
Line drawing of a hand inserting a screw into a device labeled A (no text or symbols on the device itself)
text_image
B RIGHT SIDE CLIPFINAL ASSEMBLY
text_image
A B C D(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
3 Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
| 12V Ignition / Acc. .... . Red | Right Front (+) .... . Gray |
| 12V Batt / Memory. .... . Yellow | Right Front (-).... Gray/ Black |
| Ground. .... . Black* | Left Front (+) .... . White |
| Power Antenna. .... . Blue | Left Front (-). ... White / Black |
| Amp Turn-On. .... . Blue / White | Right Rear (+) .... . Violet |
| Amp Ground. .... . Black / White | Right Rear (-) .... . Violet / Black |
| Illumination. .... . Orange | Left Rear (+) .... . Green |
| Dimmer. .... . Orange / White | Left Rear (-) .... . Green / Black |
*NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer's specifications.
99-7330 INSTRUCTIONS