99-3300 - Kit voiture Metra - Free user manual and instructions

USER MANUAL 99-3300 Metra

INSTALLATION INSTRUCTIONS FOR PART 99-3300

APPLICATIONS

GM

MULTI KIT

(see models list inside)

99-3300

KIT FEATURES

• DIN Mount Radio Provision
• Shaft Mount Radio Provision

Interior view of a car dashboard with air conditioners and a digital display (no visible text or symbols)

KIT COMPONENTS

A) Radio Housing • Spacer

Isometric line drawing of a rectangular mechanical housing or enclosure with mounting holes and a side panel (no text or symbols)

Simple line drawing of a rectangular frame with label B (no text or symbols on the frame itself)

TOOLS REQUIRED:

Small Flat Blade Screwdriver/ Panel Removal Tool

- Phillips Screwdriver • Cutting Tool • Socket Set

Line drawings of five different types of screwdrivers and tools (no text or symbols)

TABLE OF CONTENTS

Dash Disassembly

Chevrolet

-Blazer 1998-2002 ....1

-Camaro 1997-2002....2

- Caprice 1994-1996....3

-Cavalier 1995-1999 ....4

-Corvette 1997-2004 ....5

- Impala 1994-1996.... 3

-Lumina 1995-2001 .... 6

- Malibu 1997-2000 ..... 7

-Monte Carlo 1995-1999....6

- S-10 Pickup 1998-2002....1

-Venture 1997-1999 8

GMC

Refer also to the instructions included with the aftermarket radio.

Chevrolet Blazer/5-10 Pickup,

GMC Jimmy/Sonoma 1998-2002, GMC Envoy, Isuzu Hombre, Oldsmobile Bravada 1998-2001

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Remove (2) 9/32" hex head screws from the lower dash trim panel below steering column.
3 Remove (2) 9/32" hex head screws from bottom edge of instrument cluster trim panel.
4 Remove (1) Phillips head screw from above the instrument cluster.

5 Unclip and remove instrument cluster trim panel.
6 Remove (2) 9/32" hex head screws securing radio. Unplug and remove radio.

Continue to kit assembly.

Technical line drawing of a mechanical component with internal parts and mounting holes (no text or symbols)

Chevrolet Camaro 1997-2002

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove the radio trim panel. (Figure A)
3 Remove (2) 9/32" hex head screws securing radio. Unplug and remove radio. (Figure A)
4 Cut and remove the rear support from the back of radio cavity. (Figure B)

Continue to kit assembly.

B

Dash cavity

A

Technical line drawing of a car air vent assembly, showing front and side views (no text or symbols)

Chevrolet Caprice, Impala 1994-1996

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Remove (5) 9/32" hex head screws from the ashtray cavity.
3 Remove (4) 9/32" hex head screws from bottom edge of dash trim panel.
4 Unclip fuse box cover and remove (1) 9/32" hex head screw from fuse box cavity.
5 Remove (2) 9/32" hex head screws from above instrument cluster.
6 Engage parking brake and place gear selector in "D1".

7 Unclip and remove instrument cluster trim panel.
8 Remove (1) 9/32" hex head screw from the left edge of dash trim panel.
9 Unclip and remove dash trim panel.
10 Remove (2) 9/32" hex head screws securing radio. Unplug and remove radio.
11 Cut and remove the rear support from the back of radio cavity. (Figure A)

Continue to kit assembly.

A

Dash cavity

Technical line drawing of a vehicle chassis with internal components and mounting holes (no text or labels)

Chevrolet Cavalier 1995-1999

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Remove (3) 9/32" hex head screws from along top edge inside of glove box.
3 Remove (2) 9/32" hex head screws from behind glove box. (Access these screws thru cutout in rear of glove box at top left corner.)
4 Remove (1) Phillips head screw from defroster vent and remove the vent.
5 Remove (1) Phillips head screw from inside defroster.
6 Unclip and remove the trim panel at each of dash and remove (1) Phillips head screw from behind panel.

7 Remove dash pad.
8 Remove (3) Phillips head screws from top edge of instrument cluster/radio trim panel. Unclip and remove dash trim panel.
9 Remove (2) 9/32" hex head screws securing radio. Unplug and remove radio.
10 Cut and remove the rear support from the back of radio cavity. (Figure A)

Continue to kit assembly.

A

Dash cavity

Technical line drawing of a mechanical component with two views (front and side), no text or symbols present.

Chevrolet Corvette 1997-1999

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Using a panel removal tool pry out on the "Ride Control" switch, unplug and remove switch.
3 Unclip and remove switch trim panel.
4 Remove (2) 10 MM hex head bolts from behind panel.
5 Open center console door and remove (4) screws from hinge to remove door.
6 Open ashtray and remove (1) screw securing ashtray.

7 Remove ashtray and remove (1) screw from ashtray cavity.
8 Unclip and remove small grill to the left of the ignition switch.
9 Remove one (1) screw from behind grill. Unclip and remove dash trim panel.
10 Remove (2) 9/32" hex head screws securing radio. Unplug and remove radio.

Continue to kit assembly.

Line drawing of a computer monitor with an open screen, shown in two different angles (no text or symbols)

Chevrolet Lumina/Monte Carlo 1995-2001

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove dash trim panel. (It may be necessary to loosen the lower dash trim panel below steering column.)
3 Remove (2) 9/32" hex head screws securing radio. Unplug and remove radio.
4 Cut and remove the rear support from the back of radio cavity. (Figure A)

Continue to kit assembly.

A Dash cavity

Technical line drawing of two views of a vehicle dashboard showing internal compartments and structural elements (no text or symbols)

Chevrolet Malibu 1997-2000

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove the radio trim panel.
3 Remove (2) 9/32" hex head screws securing radio. Unplug and remove radio.

Continue to kit assembly.

Technical line drawing of two mechanical components with mounting holes and internal compartments (no text or symbols)

Chevrolet Venture, Pontiac TransSport 1997-1999, Oldsmobile Silhouette 1997-2000, Pontiac Montana 1999

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Remove ashtray and remove (1) Phillips head screw from ashtray cavity.
3 Remove (1) Phillips head screw from cigarette lighter cavity.

4 Unclip and remove the radio trim panel.
5 Remove (2) 9/32" hex head screws securing radio. Unplug and remove radio.
6 Cut and remove the rear support from the back of radio cavity. (Figure A)
Continue to kit assembly.

A Dash cavity

Technical line drawing of a device housing with internal compartments and screw fasteners (no text or symbols)

DIN MOUNT RADIO PROVISION

*Note: Refer also to the instructions included with the aftermarket radio.

1 Cut and remove the shaft supports from the radio housing. (Figure A)
2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure B) NOTE: The spacer included with this kit can be used between the radio and the DIN cage for vehicles with shallow radio cavities if necessary. (Figure D)
3 Slide the aftermarket radio into the cage until it snaps into place. (Figure C) Continue to final assembly.

Illustration of a hand using a tool to adjust or install a mechanical component (no text or symbols visible)

Illustration of a hand using a screwdriver to adjust or install an electronic device component (no text or symbols visible)

D OPTIONAL

Technical line drawing of a mechanical device with no visible text or symbols

SHAFT MOUNT RADIO PROVISION

*Note: Refer also to the instructions included with the aftermarket radio.

1 Slide the aftermarket radio into the radio housing from the back and secure using shaft nuts supplied with the radio. (Figure A)

Continue to final assembly.

A

FINAL ASSEMBLY

A B C D

(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape

1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
3 Reassemble radio and dash assemblies in reverse order of disassembly.

FINAL WIRING CONNECTIONS

Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE

12V Ignition / Acc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	Right Front (+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12V Batt / Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	Left Front (+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Amp Turn-On. . . . . . . . . . . . . . . . . Blue / White Amp Ground. . . . . . . . . . . . . . . Black / White Illumination. . . . . . . . . . . Orange Dimmer. . . . . . . . . . . . . . Orange / White	Left Front (-). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Right Rear (+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Right Rear (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Left Rear (+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Left Rear (-) . . . . . . . . . . . . Green / Black

*NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer's specifications.

NOTES

NOTES

99-3300 INSTRUCTIONS