99-7815B - Kit voiture Metra - Free user manual and instructions

USER MANUAL 99-7815B Metra

INSTALLATION INSTRUCTIONS FOR PART 99-78158

Acura TL 2004-2008 99-7815B

KIT FEATURES

• ISO DIN radio provision with pocket
- Painted matte black

Interior view of a vehicle showing a mounted touchscreen device with no visible text or symbols

KIT COMPONENTS

- A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8" Phillips screws

A

B

C

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: 70-1721 Antenna Adapter: 04-06 not required • 07-08 40-HD10

Steering wheel control interface: ASWC-1

Table of Contents

Dash Disassembly 2-5

Kit Preparation....6

Kit Assembly 7

TOOLS REQUIRED

- Panel removal tool - Phillips screwdriver

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

99-78158

Dash Disassembly

1. Unclip the trim panels along the sides of the dash, down to the console. (Figure A)
2. Remove (9) Phillips screws along the top of the console, and (2) Phillips screws inside the console's rear storage compartment. (Figure B)
3. Slide the console back. Continued on next page

Interior view of a car dashboard and infotainment system (no text or symbols visible)

(Figure A)

Screws to be removed inside console storage compartment

(Figure B)

99-78158

Dash Disassembly (cont.)

1. Drop the glove box door, remove (2) Phillips screws, and (2) push pins to drop the glove box assembly. (Figure C)
2. Remove (1) push pin and remove the driver's knee panel. (Figure D)
3. Remove (1) Phillips screw from each side console panel, and unclip to remove the panels. (Figure E)

Continued on the next page

Technical diagram of a car air vent with labeled components and directional arrows indicating airflow or movement.

(Figure C)

Mechanical component diagram showing a lever mechanism with directional arrow (no text or symbols)

(Figure D)

Diagram of a vehicle interior showing dashboard, seats, and control panels (no text or labels)

(Figure E)

99-78158

Dash Disassembly (cont.)

1. Unclip and remove the shift lever trim panels, then remove (2) Phillips screws to remove the lower console storage pocket. (Figure F)
2. Unclip, unplug, and remove the vent assembly from above the radio. (Figure G)

Continued on the next page

Interior view of a car dashboard and infotainment system showing the intake compartment, dashboard, and steering wheel (no text or symbols visible)

(Figure F) (Figure G)

Interior view of a car dashboard with air vent and fan (no text or symbols visible)

99-78158

Dash Disassembly (cont.)

1. Remove (4) Phillips screws to remove the factory radio assembly. (Figures H, I)

Continue to Kit Preparation

Upper screws

(Figure H) (Figure I)

Lower screws

99-78158

Kit Preparation

1. Remove the factory radio brackets to release the factory climate controls/screen for kit assembly. (Figure A)
2. Remove the (2) factory speed clips from the bottom mounting tabs of the radio, and slide them onto the bottom mounting tabs of the 99-7815B radio trim panel. (Figure B)

Continue to Kit Assembly

Technical diagram of a mechanical component with mounting holes and a directional arrow (no text or symbols)

(Figure A) (Figure B)

Technical line drawing of a mechanical housing component with mounting brackets and a side panel (no text or symbols)

99-7815B

Kit Assembly

ISO DIN radio provision with pocket

1. Attach the radio brackets to the factory climate controls using the factory hardware. (Figure A)
2. Attach the radio trim panel to the bottom of the factory climate controls using the factory hardware. (Figure B)
3. Attach the pocket to the bracket/radio trim panel assembly using the (4) supplied #8 x 3/8" Phillips screws. (Figure C)
4. Remove the metal DIN sleeve and trim ring from the aftermarket radio.
5. Slide the radio into the bracket/ panel assembly and secure it using the screws supplied with the radio. (Figure D)

Technical line drawing of a mechanical housing component with mounting holes and internal cavities (no text or symbols)

Technical line drawing of a car air vent system with mounting holes and control panel (no text or symbols)

1. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio and climate controls. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Test the radio and climate controls for proper operation.
2. Reassemble the dash in reverse order of disassembly.
3. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio and climate controls. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Test the radio and climate controls for proper operation.
4. Reassemble the dash in reverse order of disassembly.

Technical line drawing of a car air vent system with labeled components (no text or symbols)

(Figure C)(Figure A)

Technical diagram of a car air conditioner unit with labeled components and directional arrows indicating airflow or movement.

(Figure D)(Figure B)

INSTALLATION INSTRUCTIONS FOR PART 99-7815B

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerInstitute.com or call 800-354-6762 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

04-06 Acura TL Navigation Screen Activation

If the factory navigation screen does not power back on after replacing the factory radio, you can follow the steps below to get it on again.

Steps

1.) Locate the gray 26-pin connector that came out of the factory radio.

2.) Place a 100ohm resistor across the red wire (pin 26) and blue wire (pin 13)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

07-08 Acura TL Navigation Screen Activation

If the factory navigation screen does not power back on after replacing the factory radio, you can follow the steps below to get it working again.

Steps

1.) Locate the gray 40-pin connector that came out of the factory radio.
2.) Place a 110ohm resistor across the pink wire (pin 29) and light blue wire (pin 9)

1 2 / / 8 9 10 11 12 13 14 15 16 / / / / 21 22 / / 25 26 27 2 29 30 31 32 33 34 35 36 37 38 39 40