99-8266 - Kit voiture Metra - Free user manual and instructions

USER MANUAL 99-8266 Metra

Interior view of a modern car dashboard with visible steering wheel, dashboard display, and control panel (no text or symbols)

Toyota Camry (w/ separate climate bezel) 2018-2020

Visit NetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications

KIT FEATURES

• ISO DIN radio provision with pocket
• ISO DDIN radio provision
- Tinted metallic finish

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8" Phillips screws

Line drawing of a mechanical component or bracket with no visible text or symbols

Two abstract line drawings of folded paper or paper sheets with geometric shapes and dot patterns, no text or symbols present.

TABLE OF CONTENTS

Dash Disassembly 2-3

Kit Preparation 4

Kit Assembly

-ISO DIN radio provision with pocket ....5
-ISO DDIN radio provision ....5

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: Visit metraonline.com for audio/video and steering wheel control interface options. Antenna Adapter: 40-LX11

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver
• 10mm Socket wrench

Attention! With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections are secure before cycling the ignition to test this product.

DASH DISASSEMBLY

1. Unclip and remove the dashboard trim panel below the climate controls. (Figure A)
2. For models with a push button start: Unclip the Start/Stop button trim panel and set it to the side. (Figure B)

For models without a push button start: Unclip and remove the trim panel to the left of the radio/climate control panel. (Figure C)

Interior view of a car dashboard and steering wheel (no text or symbols visible)

1. Unclip and remove the lower dashboard trim panel directly above the glovebox. (Figure D)

Continued on the next page

Line drawing of a car interior showing a hand valve and dashboard (no text or symbols)

(Figure B) (Figure D)

Interior view of a car dashboard with steering wheel, dashboard panel, and control buttons (no visible text or symbols)

(Figure C)(Figure A)

Diagram of a car interior showing steering wheel, dashboard, and seat area (no text or labels)

DASH DISASSEMBLY (CONT.)

1. Unclip and remove the upper dashboard trim panel with a/c vent. (Figure E)
2. Unclip the climate control panel and set it to the side. (Figure F)

Technical line drawing of a car interior showing a handle and seat assembly (no text or symbols)

(Figure E) (Figure G)

1. Remove (4) 10mm screws securing the radio panel, then unplug and remove the panel. (Figures G, H)

Continue to Kit Preparation

Interior view of a car dashboard and infotainment system (no visible text or symbols)

(Figure F) (Figure H)

Technical line drawing of a car dashboard with control panel and directional arrows (no text or symbols)

Mechanical assembly diagram showing a bracket with mounting holes and a valve (no text or labels)

KIT PREPARATION

1. Unclip and remove the passenger airbag light assembly from the factory radio panel, then attach the assembly to the radio trim panel. (Figure A)

2. Remove the panel clips from the factory radio panel, then attach them onto the radio trim panel. (Figure B).

Continue to Kit Assembly

Technical line drawing of a mechanical device interior showing internal components and directional arrows (no text or symbols)

(Figure A)

3D model of a mechanical component with dashed alignment lines (no text or symbols)

(Figure B)

KIT ASSEMBLY

ISO DIN radio provision with pocket

1. Attach the radio brackets to the pocket using the (4) #8 x 3/8" Phillips screws provided. (Figure A)
2. Remove the metal DIN sleeve and trim ring from the aftermarket radio.
3. Slide the radio into the bracket/pocket assembly, then secure it using the screws supplied with the radio. (Figure B)
4. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.
5. Connect the passenger airbag assembly, then secure the completed assembly to the dash using the factory screws.
6. Reassemble the dash in reverse order of disassembly to complete the installation.

Technical line drawing of a mechanical device with mounting brackets and wiring (no text or symbols)

(Figure A)

Technical line drawing of a device casing with internal components and mounting brackets (no text or symbols)

(Figure B)

ISO DDIN radio provision

1. Attach the radio brackets to the radio using the screws supplied with the radio. (Figure A)
2. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.
3. Connect the passenger airbag assembly, then secure the completed assembly to the dash using the factory screws.
4. Reassemble the dash in reverse order of disassembly to complete the installation.

Technical diagram of an electronic device with labeled ports and internal components

(Figure A)

Having difficulties? We're here to help.

our Tech Support line at:

386-257-1187

Or via email at:

[e-mail]

Tech Support Hours (Eastern Standard Time)

Monday - Friday: 9:00 AM - 7:00 PM

Saturday: 10:00 AM - 7:00 PM

Sunday: 10:00 AM - 4:00 PM

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills b enselling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.edu or call

366-672-5171 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians