CS135H31 - Sewing machine Union Special - Free user manual and instructions

USER MANUAL CS135H31 Union Special

ILLUSTRATED PARTS MANUAL

CS100 SERIES, DIFFERENTIAL FEED, HIGH SPEED CYLINDER BED MACHINES

MANUAL NO. PT9801

FOR STYLES

CS122E11 CS122H01 CS122H21 CS122K01

CS132E11 CS132H01 CS132H21 CS132K01

CS125E61 CS125H11 CS125H31 CS122K02

CS125E62 CS135H11 CS135H31 CS132K02

CS135E61 CS125H12 CS125H32

CS135E62 CS135H12 CS135H32

USE IN CONJUNCTION WITH MACHINE SERIAL NUMBER PREFIX (BG) AND LATER

REV 6-14-00

SecondEdition Copyright 2000

By

Union Special Corporation Rights Reserved In All Countries

Printed in U.S.A. April 2000

PREFACE

This parts manual has been prepared to assist you in locating individual parts or assemblies on CS100 Series machines.

IDENTIFICATION OF MACHINES

Each UNION SPECIAL machine is identified by a style number, which is stamped into the style plate affixed to the middle of the machine under the tension assembly. The serial number is stamped into the serial number plate affixed to the right rear base of the machine.

CONTENTS

PREFACE 2

IDENTIFICATION OF MACHINES 2

STYLES OF MACHINES 4

STYLES OF MACHINES (CONT.) 5

ILLUSTRATIONS 5

IDENTIFYING PARTS 5

NEEDLES 5

SAFETY RULES 6

BUSHINGS 9

NEEDLE BAR....11

UPPER MAIN SHAFT 13

SPREADER 15

THREAD GUIDE 17

PRESSER FOOT LIFT 21

COVERS, UPPER ARM 23

LOWER MAIN SHAFT 25

LUBRICATION, OIL TUBING & OIL PUMP 27

LOOPER DRIVE 29

LOOPER THREAD TAKE -UP & NEEDLE GUARD 31

FEED DRIVE MECHANISM 33

FEED DRIVE MECHANISM 35

COVERS FOR CS122E11, CS132E11, CS125E61, CS125E62, CS135E61, CS135E62.... 37

COVERS LOWER BED- FRONT 39

COVERS LOWER BED- MIDDLE 41

COVERS LOWER BED - REAR 43

SEWING PARTS FOR CS122E11, CS125E61, CS125E62, CS132E11, CS135E61, CS135E62....45

SEWING PARTS FOR CS122H01, CS132H01 47

SEWING PARTS FOR CS125H11, CS125H12, CS135H11, CS135H12....49

SEWING CHART FOR CS125H11, CS135H11 50

SEWING CHART FOR CS125H12, CS135H12 51

SEWING PARTS FOR CS122H21, CS132H21 53

SEWING PARTS FOR CS122K01, CS122K02, CS132K01, CS132K02 55

ACCESSORIES 57

TAPE GUIDE, HOLD DOWN DEVICE FOR CS122E11, CS125E61, CS125E62, CS132E11, CS135E61, CS135E62....59

UNDER TRIMMER ASSEMBLY FOR CS122E11, CS125E61, CS125E62, CS132E11, CS135E61, CS135E62....61

PULLER LIFTER ASSEMBLY FOR CS125E61, CS125E62, CS125H11, CS125H12, CS135E61, CS13562, CS135H11, CS135H12 .... 63

PULLER DRIVE ASSEMBLY FOR CS125E61, CS125E62, CS125H11, CS125H12, CS135E61, CS13562, CS135H11, CS135H12 .... 65

LOWER ROLLER ASSEMBLY FOR CS125E61, CS125E62, CS125H11, CS125H12, CS135E61, CS135E62, CS135H11, CS135H12 .... 67

UPPER ROLLER ASSEMBLY FOR CS125E61, CS125E62, CS125H11, CS125H12, CS135E61, CS135E62, CS135H11, CS135H12 .... 69

FABRIC TRIMMER ASSEMBLY FOR CS122H21, CS132H21 71

NEEDLE DIPPER (EXTRA SEND CHARGE) 73

NUMERICAL INDEX OF PARTS 74

NUMERICAL INDEX OF PARTS 75

NUMERICAL INDEX OF PARTS 76

NUMERICAL INDEX OF PARTS 77

NOTES 78

NOTES 79

STYLES OF MACHINES

Precision two or three needle cylinder bed machines, with top and bottom coverstitch or bottom coverstitch only. Rotary mainshafts for smoother, quieter and faster operations. Equipped with quick change for main and differential feed. Independently driven rear needle guard, no adjustment necessary when changing stitch length. Adjustable looper avoid eccentric to adapt the looper avoid motion and the elliptic path of looper to the required needle size and type of sewing threads. Recommended needle 121GJS, needle range sizes 055/022 - 090/036.

CS122E11	ELASTIC. Two or three needle, bottom coverstitch, right hand fabric undertrimmer. - Typical Application - For attaching preclosed elastic while trimming the edge of the fabric. Seam Specification for two needle 406 LSA-1, for three needle 407 LSA-1. Standard gauge for two needle 40, (5/32", 4.0mm), 48, (3/16", 4.8mm), for three needle 56, (7/32", 5.6mm), 64, (1/4", 6.4mm). Maximum recommended speed, depending on application is up to 5500 R.P.M..
CS132E11	ELASTIC. Same as Style CS122E11 except top coverstitch, Seam Specification for two needle 602 LSA-1, for three needle 605 LSA-1.
CS125E61	ELASTIC. Same as CS122E11 except equipped with rear roller.
CS125E62	ELASTIC. Same as CS122E11 except equipped with rear roller.
CS135E61	ELASTIC. Same as CS132E11 except equipped with rear roller.
CS135E62	ELASTIC. Same as CS132E11 except equipped with rear roller.
CS122H01	HEMMING. Two or three needle, bottom coverstitch. - Typical Application - For circular hemming operations on light, medium and heavy weight knit fabrics. Seam Specifications for two needle 406 EFa-1(inv.), for three needle 407 EFa-1 (inv.). Standard gauges for two needle 40, (5/32", 4.0mm), 48, (3/16", 4.8mm), for three needle 56, (7/32", 5.6mm), 64, (1/4", 6.4mm). Recommended speed, depending on application is up to 6500 R.P.M..
CS132H01	HEMMING. Same as Style CS122H01 except, top and bottom coverstitch. Seam Specification for two needle 602 EFa-1 (inv.), for three needle 605EFa-1 (inv.).
CS125H11	HEMMING. Two or three needle, rear puller. - Typical Application - For hemming applications. Seam Specifications for two needle 406 EFa-1 (inv.), for three needle 407 EFa-1 (inv.). Standard gauges for two needle 40, (5/32", 4.0mm), 48, (3/16", 4.8mm), for three needle 56, (7/32", 5.6mm), 64, (1/4", 6.4mm). Maximum recommended speed, depending on application is up to 6000 R.P.M..
CS135H11	HEMMING. Same as Style CS125H11 except top and bottom coverstitch. Seam Specification for two needle 602 EFa-1 (inv.), for three needle 605 EFa-1 (inv.).
CS125H12	HEMMING. Same as CS125H11 except equipped with rubber roller on rear puller.
CS135H12	HEMMING. Same as CS135H11 except equipped with rubber roller on rear puller.
CS122H21	HEMMING. Two or three needle, left hand fabric undertrimmer, bottom coverstitch. - Typical Application - For general hemming of circular openings while trimming the edge of the hem. Seam Specifications for two needle 406 EFa-1 (inv.), for three needle 407 EFa-1 (inv.). Standard gauges for two needle 40, (5/32", 4.0mm), 48, (3/16", 4.8mm), for three needle 56, (7/32", 5.6mm), 64, (1/4", 6,4mm). Maximum recommended speed, depending on application is up to 5500 R.P.M..
CS132H21	HEMMING. Same as Style CS122H21 except top and bottom coverstitch. Seam Specification for two needle 602 EFa-1 (inv.), for three needle 605 EFa-1 (inv.).
CS122K01	COVERSEAM. Two needle, bottom coverstitch. - Typical Application - for the second operation to bottom coverstitch overedge seams of circular openings such as shoulder, neck, and waist of light weight knit garments. Seam Specification 406 SSh-2. Standard gauges 48, (3/16", 4.8mm), 56, (7/32", 5.6mm), 64, (1/4", 6.4mm). Recommended speed, depending on application is up to 6500 R.P.M..
CS122K02	COVERSEAM. Same as Style CS122K01 except Adjustable, split seam guide, for medium to heavy weight knit garments. Standard gauges 56, (7/32", 5.6mm), 64, (1/4", 6.4mm).

STYLES OF MACHINES (CONT.)

CS132K01 COVERSEAM. Same as Style CS122K01 except top and bottom coverstitch. Seam Specifications 602 SSh-2. - Typical Application - for light to medium fabrics.

CS132K02 COVERSEAM. Same as Style CS122K02 except Seam Specification 602 SSh-2.

ILLUSTRATIONS

This manual has been arranged to simplify ordering repair parts. Exploded views of various sections of the mechanism are shown so that the parts may be seen in their actual position in the machine. On the page opposite the illustration will be found a listing of the parts with their part numbers, description and the number of pieces required in the particular view being shown.

Numbers in the first column are reference numbers only, and merely indicate the position of the part in the illustration. The reference number should never be used in ordering parts. Always use the part number listed in the second column.

Component parts of sub-assemblies which can be furnished for repairs are indicated by indenting their descriptions under the description of the main sub-assembly. As an example refer to the following text.

1. 50366B Needle Thread Strike-Off Assembly ....1
2. 50358V Needle Thread Strike-Off 1
3. 50370F Thread Strike-Off Component 1
4. SS7060310SP Screw, for plate strike-off 1

When a part is common to all machines covered in this manual, no specific usage will be mentioned in the description. However, when the parts for the various machines are not the same, the specific usage will be mentioned in the description and, if necessary, the difference will be shown in the illustration.

*NOTE: Ref. No. showing no Part No. is for location only. Part is not for sale separately.

A numerical index of all the parts shown in this manual is located at the back. This will facilitate locating the illustration and description when only a part number is known.

IDENTIFYING PARTS

Where construction permits, each part is stamped with its part number. On some of the smaller parts and on those where construction does not permit, an identification letter is stamped in to distinguish the part from similar ones.

PLEASE NOTE: Part numbers represent the same part, regardless of which manual they appear. On all orders please include part number, name and style of machine for which the part was ordered.

For optimum performance use only genuine Union Special replacement parts.

NEEDLES

Each needle has both a type and size number. The type number denotes the kind of shank, point, length, groove, finish and other details. The size number, stamped on the needle shank, denotes the largest diameter of the blade measured between the shank and the eye. Collectively, the type number and size number represent the complete symbol which is given on the label of all needles packed and sold by Union Special.

TYPE

DESCRIPTION

121 GJS Short, double groove, struck groove, ball eye, spotted, ball point, chromium plated- Sizes available 055/022, 065/025, 070/027, 075/029, 080/032, 090/036.

When changing the needle, make sure it is fully inserted in the holder before the screw is tightened.

When ordering needles, please use the complete type and size numbers as printed on the package to ensure prompt and accurate processing of your order. A complete order should read as follows: "100 needles, type 121 GJS, size 075/029".

SAFETY RULES

1. Before putting the machines described in this manual into service, carefully read the instructions. The starting of each machine is only permitted after taking notice of the instructions and by qualified operators.

IMPORTANT! Before putting the machine into service, also read the safety rules and instruction from the motor supplier.

1. Observe the national safety rules valid for your country.

2. The sewing machines described in this instruction manual are prohibited from being put into service until it has been ascertained that the sewing units which these sewing machines will be built into, have conformed with the EC Council Directives (89/392/EEC, Annex II B).

Each machine is only allowed to be used as foreseen. The foreseen use of the particular machine is described in paragraph "STYLES OF MACHINES" of this instruction manual. Another use, going beyond the description, is not as foreseen.

1. All safety devices must be in position when the machine is ready for work or in operation. Operation of the machine without the appertaining safety devices is prohibited.

2. Wear safety glasses.

3. In case of machine conversions and changes all valid safety rules must be considered. Conversions and changes are made at your own risk.

4. The warning hints in the instructions are marked with one of these two symbols:

1. When doing the following the machine has to be disconnected from the power supply by turning off the main switch or by pulling out the main plug:

8.1 When threading needle(s), looper, spreader etc.
8.2 When replacing any parts such as needle(s), presser foot, throat plate, looper, spreader, feed dog, needle guard, folder, fabric guide etc.
8.3 When leaving the workplace and when the workplace is unattended.
8.4 When doing maintenance work.
8.5 When using clutch motors without actuation lock, wait until the motor is stopped totally.

1. Maintenance, repair and conversion work (see item 8) must be done only by trained technicians or special skilled personnel under consideration of the instructions.

2. Any work on the electrical equipment must be done by an electrician or under direction and supervision of special skilled personnel.

3. Work on parts and equipment under electrical power is not permitted. Permissible exceptions are described in the applicable sections of standard sheet DIN VDE 0105.

4. Before doing maintenance and repair work on the pneumatic equipment, the machine has to be disconnected from the compressed air supply. In case of existing residual air pressure after disconnecting from compressed air supply (i.e. pneumatic equipment with air tank), the pressure has to be removed by bleeding.

CS100 SERIES

BUILDING BLOCK STYLE

DESIGNATION SYSTEM

graph TD
    A["SUB-CLASS (DESCRIBES TYPICAL APPLICATION)<br>C:=COLLARETTE<br>E:=ELASTIC<br>H:=HEMMING<br>K:=COVERSEAM<br>L:=LAP SEAM<br>U:=UNIVERSAL<br>•00-99=VARIETY OF SUBCLASS"] --> B["STITCH TYPE<br>2=BOTTOM COVERSTITCH<br>3=TOP & BOTTOM COVERSTITCH"]
    A --> C["NEDLE SPACING<br>32=3.2mm<br>40=4.0mm<br>48=4.8mm<br>56=5.6mm<br>60=6.0mm<br>64=6.4mm"]
    B --> D["BASIC FRAME STYLE<br>CS=CYLINDER BED<br>FS=FLAT BED"]
    D --> E["CS132E11-3B56/____/____/____/____"]
    B --> F["NUMBER OF NEEDLES<br>2=TWO NEEDLE MACHINE<br>3=THREE NEEDLE MACHINE"]
    F --> G["DEVICES<br>CC:=CHAIN CUTTER<br>MD:=METERING DEVICE<br>TC:=TAPE CUTTER<br>TF:=BINDING FEED DEVICE<br>UT:=THREAD TRIMMER<br>•1-9=VARIETY OF DEVICES"]
    E --> H["GENERATION<br>1=FIRST<br>2=SECOND<br>3=THIRD"]
    E --> I["FEED TYPE<br>2=DIFFERENTIAL<br>5=DIFFERENTIAL&PULLER"]
    I --> J["STITCH TONGUE<br>REPRESENTS THE SHAPE OF THE<br>THROAT PLATE STITCH TONGUE.<br>A:FOR SHORT STITCH LENGTH A □<br>B:FOR MEDIUM STITCH LENGTH B □<br>C:FOR LONG STITCH LENGTH C □<br>D:FOR ALL STITCH LENGTHS, D □<br>COLLARETTE, COVERSEAM & ELASTIC APPLICATIONS"]

Loctite Union Special No. CE27

BUSHINGS

Ref.

No. Part No.

Description

Amt.

Req.

1. 50347E Bushing, for spreader, rear .... 1
2. 50347F Bushing, for spreader, front 1
3. 50354J Bushing, for needle bar, upper 1
4. 50344BU Bushing, for upper main shaft, front 1
5. 50332U Pin 1
6. 50347L Bushing, for spreader drive 1
7. 50354H Bushing, for needle bar, lower 1
8. 50330CZ Bushing, for presser bar 1
9. 99352 Stop Screw 2
   Stop 1
10. 22894BD Screw, for cast-off plate stud 1
11. 96841 Pin.... 1
12. 34390 Bushing, for main shaft, left 1
13. 50393EZ Oil Seal 1
14. 34336C Bushing, for feed rocker, left 1
15. 34336D Bushing, for feed lifter shaft, left 1
16. 34336B Bushing, for feed rocker shaft, right.... 1
17. 34336E Bushing, for feed lifter shaft, right 1
18. 22565C Set Screw 1
19. 50344BP Bushing, for main shaft, middle 1
20. 34394A Oil Tube 1
21. 50393KW Oil Tube 1
22. 22894AD Screw 1
23. 999-211B "O" Ring 1
24. 50344BL Bushing, for cast-off plate bracket 1
25. PS0400142KH Pin 1
26. 50381E Bushing, for lifter lever, back 1
27. 50392AB Bushing, for tension release 1
28. 22571F Plug Screw 2
29. 34394B Oil Tube 1
30. 50393GF Oil Sight Gauge 1
31. 34342G Bushing, for looper drive shaft, front 1
32. 50344BN Differential Feed Adjusting Assembly 1
    Differential Feed Adjusting Shaft 1
    "O"Ring 1
    Differential Adjusting Bushing 1
33. 34342F Bushing, for looper drive shaft rear 1
34. 22829 Screw 1
35. 50344AV Bushing 1
36. SS8660612TP Screw 1
37. 999-211 "O" Ring 1

TORQUE: 12in.1bs. (2.0-2.3Nm) TORQUE: 18-20in.1bs. (2.0-2.3Nm) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Loctite: Union Special No. CE59 Loctite: Union Special No. CE27

NEEDLE BAR

Ref.

No. Part No.

Description

Amt.

Req.

1. SS4080620TP Screw 1
2. 50323P Needle Bar Eyelet 1
3. 50317B Needle Bar 1
4. 50345W Connecting Rod Assembly 1
5. 50355AM Needle Bar Clamp 1
6. SS7111120TP Screw 1
7. 50352 Pivot Pin 1
8. 661-259B Needle Bearing Cage 1
9. 50355AN Connecting Rod 1
10. 50351A Washer 1
11. 50393JP Eyelet Seal 1
12. 50358X Needle Thread Eyelet 1
13. SS7080520SP Screw 1
14. CE27 Loctite Adhesive, (not shown), for screw
15. 50354F Slide Block 1
16. CE63 Three Bond Adhesive, (not shown), for slide block ....
17. SS8110422TP Screw 1
18. 29476TC Oil Tube Assembly 1
19. CQ25220000 Wick 1
20. 50393JY Oil Tube 1
21. 50393JZ Oil Tube 1
22. 50393JW Hose Clamp 1
23. SS6090440SP Screw, for support bracket 1
24. SS6121010SP Screw 2
25. 29476TH Slide Block Guide Assembly 1
26. 50354G Slide Block Guide 1
27. 50393HS Sponge 1
28. CE59 Loctite Adhesive, (not shown), for sponge
29. 50394AF Slide Block Guide Cover 1
30. SS6090620SP Screw 1
31. 666-329 Felt 1

TORQUE: 32-34in.1bs. (3.8-3.9Nm) TORQUE: 46-48in.1bs. (5.2-5.4Nm) TORQUE: 10 11 12 13 14 15 16 17 18 TORQUE: 46-48in.1bs. (5.2-5.4Nm) TORQUE: 46-48in.1bs. (5.2-5.4Nm) TORQUE: 54-58in.1bs. (8.0-6.3Nm) TORQUE: 54-58in.1bs. (6.0-6.3Nm) Lactite: Union Special No. CE28 1 2 3 4 5 6 7 TORQUE: 32-34in.1bs. (3.6-3.9Nm)

UPPER MAIN SHAFT

Ref.

No. Part No.

Description

Amt.

Req.

1. 50322BB Upper Main Shaft Assembly 1

2. 50391 Counter Weight 1

3. SS7111120TP Screw, for counter weight 1

4. SS7681410TP Screw, for counter weight 1

5. SS8681412TP Screw, for counter weight 1

6. 50322AF Upper Main Shaft 1

7. 50335BD Bearing Adapter Assembly 1

8. SS8660612TP Screw, for bearing adapter 2

9. 661-262 Retaining Ring 1

10. 50342AY Sprocket, for upper main shaft 1

11. SS8661012TP Set Screw, for sprocket 2

12. 50391A Counterweight 1

13. SS8660612TP Screw 2

14. 50321M Handwheel.... 1

15. SS8681412TP Set Screw, for handwheel 2

16. 660-1043 Tack Pin, for hand wheel 1

17. 661-261 Load Ring, for lower main shaft 2

18. SS7660520SP Screw, for handwheel preload 1

TORQUE: 14-16in.1bs. (1.8-1.8Nm) TORQUE: 32-34in.1bs. (3.6-3.9Nm) TORQUE: 46-48in.1bs. (15.2-5.4Nm) TORQUE: 32-34in.1bs. (3.6-3.9Nm) TORQUE: 18-20in.1bs. (2.0-2.3Nm) TORQUE: 14-16in.1bs. (1.6-1.8Nm)

SPREADER

Ref.

No. Part No.

Description

Amt.

Req.

1. 50335AW Collar, for spreader shaft 1
2. SS8660512TP SetScrew 1
3. 96162B Washer 1
4. 50360B Crankshaft, for spreader assembly 1
5. 50347J Pin, for spreader rocker....1
6. 50347C Lever, for spreader holder shaft 1
   Screw 2
7. 61351C Washer 2
8. 660-739 Oil Seal 1
9. 50347G Shaft, for spreader, vertical 1
10. 50346A Spreader Holder 1
    Screw 2
    Screw 1
11. 53678N Washer....1
12. SS9090640SP Hex Screw, for vertical shaft 1
13. 50360H Spreader 1
14. 29126FW Spreader Crank Rod Assembly 1
15. 50360G Spreader Shaft Driving Arm 1
    Screw 1
16. NS6680410SP Hex Nut, for spreader drive 1
17. 50360F Connecting Rod, for spreader drive 1
18. WP0742016SP Collar, for spreader driving arm 2
    Stud 1
19. 50360 Eccentric, for spreader drive 1
20. SS8660612TP Screw 2

Technical diagram of a mechanical assembly with numbered components and labeled parts in Chinese

THREAD GUIDE

Ref.			Amt.
No.	Part No.	Description	Req.

1. SS7120640SP Screw, for lead-in eyelet 2

2. 50392AU Thread Eyelet Assembly 1

3. SS7090910TP Screw, for tube bracket 1

4. WS0510002KP Washer 1

5. 50366 Thread Eyelet Tube 2

6. 50366A Thread Eyelet Tube Bracket 1

7. 50392S Lead-in Tension Eyelet 1

8. SS4120615SP Screw, for spreader thread guide 2

9. 50363CK Needle Thread Guide & Lubricator Assembly 1

10. 50358U Thread Guide, for spreader 1

11. SS7110410SP Screw, for needle thread guide 1

12. 50393HH Silicone Thread Lubricator 1

13. WS0371026SD Washer 2

14. 50366J Needle Thread Guide 1

15. SS7080510TP Screw, for holder eyelet 1

16. SS4090815SP Screw, for silicone tank 2

17. 50358W Holder, for needle thread eyelet 1

18. SS8080410TP Screw 3

19. 36271A Adjusting Needle Thread Eyelet 3

20. SS7120710SP Screw, for strike-off 1

21. 50366B Needle Thread Strike-Off Assembly 1

22. SS7060310SP Screw, for plate strike-off 1

23. 50370F Thread Strike-Off Component 1

24. 50358V Needle Thread Strike-Off 1

25. 98A Screw 1

26. 12124202 Looper Frame Eyelet 1

27. 87U Screw 1

28. 34358F Looper Thread Guide 1

29. SS4120915SP Screw, for thread take-up cover 1

30. 50392T Eyelet 1

31. 605A Screw, for needle thread guide 2

32. C50044E Needle Thread Guide 1

33. 29475CG Spreader Thread Tension Assembly 1

34. 50392AZ Tension Nut 1

35. 50392AY Tension Spring 1

36. 50392AX Tension Disc 2

37. 50392AW Tension Post 1

38. 57844 Eyelet 1

39. 652C16 Star Washer 1

40. SS1121010SP Screw, for thread guide 1

41. 50357AR Nipper Plate Assembly 1

42. SD0380551SL Shoulder Screw 1

43. 50357AS Nipper Spring 1

44. 50357Y Nipper Spring Plate 1

45. 50357V Nipper Plate 1

46. 50366G Thread Guide 1

47. 18C1471 Screw 2

48. 29480AYJ Looper Thread Nipper 1

49. 50366L Eyelet 1

50. 50357AV Spring, Nipper 1

51. 50357AT Nipper Plate 1

52. 50357AX Nipper Plate 1

53. 50357AW Screw, Tension Post 1

54. SS7090610SP Screw, for spreader thread guide 2

55. 50346 Thread Guide Spreader 1

TORQUE: 14-16in.1bs. (1.6-1.8Nm) 20 21 22 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 19 18 19 RED BLUE PLAIN NOTE: ON THIS POST ONLY DET'S #7 AND #9 ARE REVERSED. RED AND BLUE TENSION POSTS REQUIRE THE USE OF 666-330. THE PLAIN TENSION POST REQUIRES THE USE OF B3120352000.

TENSION RELEASE & THREAD TENSION

Ref.			Amt.
No.	Part No.	Description	Req.

1. 50392Z Tension Needle Lever Assembly 1
2. 660-283A Retainer Washer 1
3. SS4120915SP Screw, for tension assembly 2
4. 50392Y 5 Thread Tension Assembly 1
5. 57892K Thread Tension Eyelet 5
6. 56392G Tension Post 5
7. B3120352000 Tension Disc Felt 1
8. 666-330 Disc Felt 4
9. B3126012000 Tension Disc 10
10. B3120704000 Tension Disc Felt 5
11. 56392H Spring Shield 5
12. 11550209 Spring, needle (green) 3
13. B3103804000 Spring, spreader (blue) 1
14. B3121804000 Spring, looper (plain) 1
15. B3112704000 Ferrule, tension spring 5
16. 50692G Knob, needle (green) 3
17. 56392M Knob, spreader (blue) 1
18. 56392R Knob, looper (plain) 1
19. 50392W Tension Disc Separator 1
20. 50392AV Guide, for tension disc separator 2
21. SS7090520SP Screw, for guide 2
22. 50392X Tension Bracket 1
23. 57865 Lead-In Thread Guide 5
24. NS6110420SP Nut 5
25. 50392BC Tension Release Lever Shaft Connection....1
26. 22875N Base Spring Screw 1
27. SS7121410TP Binder Screw 1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Loctite: Union Special No. CE66 (2 screws) Loctite: Union Special No. CE66 23 24 27 25 24 26 20 21 19 18 15 14 22 30

PRESSER FOOT LIFT

Ref.

No. Part No.

Description

Amt.

Req.

1. 11071602 Adjusting Screw, for spring 1
2. 11071701 Locking Nut 1
3. 660-1014 "O" Ring 1
4. C50056B Spring Rod 1
5. 50357AP Spring, for presser bar 1
6. 50335AF Presser Bar 1
7. SS6110610TP Screw, for guide plate 2
8. 50335AG Guide Plate, for presser bar 1
9. 50335AH Presser Bar Guide 1
10. SS8110422TP SetScrew 2
11. 660-739 Oil Seal 1
12. 50333P Collar 1
13. 22562 Screw 2
14. RE0500000K0 E Ring, for pin 1
15. 50381F Lever, for lifter, front 1
16. SD0790303SP Screw, for wire connector 1
17. CE66 Loctite Adhesive, (not shown), for screw
18. 29476TK Rear Lifter Lever Assembly 1
19. SD0790303SP Screw 1
20. 50355AR Wire Connector 1
21. 50381G Lifter Lever, rear 1
22. SS9151740CP Hex Screw 1
23. 29476TT Stop Assembly 1
24. SS6151920SP Screw, for stopper 1
25. NS6150310SP Hex Nut 2
26. 50332V Stopper, for lifter lever 1
27. SS6153040SP Screw, for adjusting stopper 1
28. SS6121010SP Screw, for adjusting stopper 2
29. CE66 Loctite Adhesive, (not shown), for screw
30. 50381 Spring, for lifter lever 1
31. RO068190100 "O" Ring 1
32. 50381B Lifter Lever Assembly 1

Technical diagram of a mechanical assembly with numbered components and labeled parts including Union Special No. CE59 and CE27.

COVERS, UPPER ARM

Ref.

No. Part No.

Description

Amt.

Req.

1. SS4121615SP Screw, for top cover 6
2. 50393EU Plug, for top cover 1
3. B3530555000 Oil Sight Gauge, top 1
4. 660-212 "O" Ring, for oil sight gauge 1
5. 50382FW Top Cover 1
6. 50382FZ Quad Ring, for top cover 1
7. SS4120915SP Screw, for puller drive cover 4
8. 50382GB Puller Drive Cover 1
9. 50384L Gasket, for puller drive cover 1
10. 50317C Needle Bar Guard 1
11. SS7120640SP Screw, for needle bar guard 2
12. 50393HB Plug 2
13. TA1050504R0 Plug, for arm 1
14. 50382FX Head Cover 1
15. 50382FY Quad Ring, for head cover 1
16. SS4121215SP Screw, for head cover 4
17. TA1100604R0 Plug 1
18. 99682XCB Sewing Guard Assembly 1
19. NS6620320SP Nut 1
20. 50383AE Bracket Holder 1
21. 50383AD Bracket 1
22. 99682XC Protection Shield 1
23. SS1110640SL Counter Sunk Head Screw 2
24. WZ0641510KP Spring Washer 1
25. SD0640323TP Shoulder Screw 1
26. 50337AW Plug....1
27. 50393EW Rubber Gasket, for needle lever 1
28. 50382JL Thread Take-Up Bracket 1
29. SS7090530SP Screw 1
30. SS4120615SP Screw, for thread cover 1
31. SS4120915SP Screw, for thread take-up cover 1
32. 50382JN Thread Take-Up Cover 1
33. 666-334 Felt Wick 1
34. 50382GM Thread Cover 1
35. SS4120615SP Screw, for thread cover 1
36. LA451 Label, in direction of rotation 1

TORQUE: 46-48 in.-lbs. (5.2-5.4 Nm) TORQUE: 46-48 in.-lbs. (5.2-5.4 Nm)

LOWER MAIN SHAFT

Ref.

No. Part No.

Description

Amt.

Req.

1. 34321CC Flange, synchronizer.... 1
2. 95205 Screw 1
3. 50321J Pulley 1
4. SS8660612TP SetScrew 2
5. 50335AP Adapter 1
6. SS8660612TP Screw, for adapter 2
7. 661-348 Retainer Ring.... 1
8. 50344AR Bearing Adaptor Assembly 1
9. SS8660612TP Screw 2
10. 50335AP Adaptor 1
11. 50311C Ball Bearing, for lower main shaft, right 1
12. 50322AN Retainer, for sprocket 1
13. 661-261 Load Ring 2
14. 22569B Screw, for housing 3
15. 50390L Rear Bearing Housing 1
16. 99658 Housing Pin 1
17. 56390E Housing Gasket 1
18. 50342BD Timing Belt 1
19. 50342BH Sprocket, for lower main shaft 1
20. SS8660612TP SetScrew 2
21. 50335BC Bearing Adapter Assembly 1
22. SS8660612TP Screw 2
23. 50322AH Lower Main Shaft, right 1
24. 96162A Washer 1
25. 50322BG Mainshaft, left 1

TO: OIL CONNECTOR 34394A (MAIN SHAFT BUSHING, OIL TUBE) TO: LOWER LEFT. REAR ON SIDE OF CASTING TO: CONNECTOR (A) IN OIL PUMP 50393HN TO: OIL CONNECTOR 34394 (ROCKER CROSS SHAFT, OIL TUBE) TO: CONNECTOR (B) IN OIL PUMP 50393HN TO: OIL CONNECTOR 34394B (RIGHT BOTTOM CAVITY OF CASTING)

LUBRICATION, OIL TUBING & OIL PUMP

Ref.

No. Part No.

Description

Amt.

Req.

1. 50393HN Oil Pump Assembly, 2 stage 1
2. 50393GD Oil Pump Housing, 2 Stage 1
3. 18-1470 Screw 2
4. 50332S Spring, for plunger 2
5. 34393D Plunger 2
6. 50393GB Oil Pump Housing, 2 Stage 1
7. 50393EX Collar 1
8. SS8660612TP Screw 2

Screw 2

1. 29476TR Oil Supply Trough Assembly 1
2. 258A Nut 1
3. 50393FH Oil Supply Trough 1
4. 41350X Washer 2
5. C50094B Connector Dual Feed 1
6. 50393GT Oil Tube Cover 2
7. 50393HE Plug Screw 1
8. 50393FK Tube 1
9. 29476TS Oil Supply Trough Assembly for CS122 and CS132 1
10. 29476VL Oil Supply Trough Assembly for CS125 and CS135 1
11. 50393FF Oil Tube 1
    9A. 50393KV Oil Tube 1
12. 50393FG Oil Tube 1
13. 50393GU "T" Connector 1
14. 50393FD Oil Tube 1
15. 50393FE Oil Tube 1
16. 50393LA Oil Screen 1
17. 29476TJ Oil Filter Assembly 1
18. 99349 Stud 1
19. 660-212 "O" Ring 1
20. 34393M Oil Screen Felt 1
21. 34393L Oil Screen 1
22. 96276 Retaining Ring 1
23. 50393HV Oil Tube 1
24. 34682C Gasket 1
25. 999-254J Oil Filter 1
26. 50382GS Base Plate 1
27. 22571E Magnet Plug 6
28. 95953 Washer 6
29. 95406 Screw 1

TORQUE: 24-26 in.-Ibs. (2.7-2.9 Nm) 3 2 1 6 Three Bond: Union Special No. CE62 TORQUE: 22-24 in.-Ibs. (2.5-2.7 Nm) TORQUE: 19-21 in.-Ibs. (2.1-2.3 Nm) 13 12 11 18 15 16 19 17 25 24 TORQUE: 108 in.-Ibs. (12 Nm) TORQUE: 14-16 in.-Ibs. (1.6-1.8 Nm) TORQUE: 132.5 in.-Ibs. (14.7 Nm)

LOOPER DRIVE

Ref.			Amt.
No.	Part No.	Description	Req.

1. 34709D Looper.... 1
2. 50348 Holder, for looper 1
3. SS6091022TP Screw 1
4. SS6090560TP Screw 1
5. 50313T Washer 1
6. 22894C Screw 2
7. 50344AG Bushing....1
8. 99652A Washer 2
9. 9937 Nut 1
10. 29476VK Looper Drive Assembly 1
11. 50343RC Bushing, for looper bar, right 1
12. 34344A Cam Guide 1
13. 34344E Cam Follower 1
14. 50344BM Bushing, for loopershaft 1
15. 22894W Screw 1
16. 39543E Locking Clamp 1
17. 34344D Cam Guide Holder 1
18. 22541B Screw 1
19. 51235G Washer 1
20. 34343C Washer 1
21. 34642A Looper Rocker Lever 1
22. HA20B Washer 1
23. 22811B Screw 1
24. 50343B Shaft, for looper 1
25. CO67D Cork 1
26. 34893 Oil Seal Plug, front 1
27. 661-253 "O" Ring 1
28. 50343C Looper Rocker Shaft 1
29. 34342J Binder Collar 1
30. 22652A12 Screw 1
31. 56390H Thrust Washer 2
32. 661-252 Snap Ring 1
33. 29105BK Looper Eccentric Assembly 1
34. G29105F Drive Lever Crank 1
35. 22894X Screw 4
36. 99346 SetScrew 1
37. 50335BE Looper Avoid Link 1
38. 50314G Looper Avoid Eccentric 1
39. SS8660512TP Screw 1
40. 99343 Screw 1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Three Bond: Union Special No. CE62

LOOPER THREAD TAKE -UP & NEEDLE GUARD

Ref.

No. Part No.

Description

Amt.

Req.

1. 29476UA Cast-Off Plate Assembly 1
2. SS7060310SP Screw 2
3. 34358BA Thread Guide, left 1
4. SS4080620TP Screw 2
5. WP0320501SC Washer 2
6. 34358CA Thread Guide, right 1
7. 50357AK Cast-Off Plate 1
8. RE0900000K0 Retaining Ring 1
9. 50357AH Spring 1
10. 50357AG Holder 1
11. 50304M Finger.... 1
12. SS7080520SP Screw 2
13. 50357AJ Shaft, for cast-off 1
14. 50325AL Needle Guard, front 1
15. 50325AB Holder, for needle guard, front 1
16. SS8090540SP Screw 1
17. 50325AM Holder, for needle guard, rear 1
18. SS6090440SP Screw 1
19. 50325AN Needle Guard, rear 1
20. 22580 Screw 1
21. 6042A Washer 1
22. 50333H Spacer 1
23. 77A Screw 1
24. 34368 Fork 1
25. 22894AD Screw 1
26. 34366 Collar 1
27. 22743 Screw 1
28. 50323S Take Up 1
29. 22894T Screw 2

FEED DRIVE MECHANISM

Ref.

No. Part No.

Description

Amt.

Req.

1. G29476BV Feed Bar Assembly 1

2. 9937 Nut 1

3. 34336N Drive Connection.... 1

4. 39536C Bushing 1

5. J87J Screw 4

6. 50386L Thrust Plate, differential 1

7. 34353A Differential Feed Dog Holder 1

8. 50386M Thrust Plate, main 1

9. 34353 Main Feed Dog Holder 1

10. 34336U Stud 1

11. 29476SH Feed Bar Assembly 1

12. 34334S Main and Differential Feed Bar 1

13. 34338 Feed Lift Slide Block 1

14. 34338B Sliding Block 1

15. GA29477AP Eccentric Assembly 1

16. 34336S Spacing Stop 1

17. 90 Screw 1

18. 96663 Roll Pin 1

19. 22738B Screw 2

20. 34336RA Washer 1

21. 97137 Disc Spring 2

22. 34336V Cam Disc 1

23. 96667 Roll Pin 1

24. 22562A Screw 1

25. 34336Q Guide, foreccentric 1

26. 22738B Screw 1

27. 34340A Eccentric 1

28. 22503F Screw 2

29. 50322BF Feed Lift Shaft 1

30. 34335J Collar 2

31. 22894X SetScrew 2

32. 34336A Differential Feed Drive Link 1

33. 34337F Eccentric Bushing 1

34. 22874C Screw 1

35. 93 Screw 2

36. 34335G Feed Bar Guide 1

37. 34382H Gasket 1

TORQUE: 46-48 in.-Ibs. (5.2-5.4 Nm) TORQUE: 30-32 in.-Ibs. (3.4-3.6 Nm) TORQUE: 37-40 in.-Ibs. (4.2-4.5 Nm)

FEED DRIVE MECHANISM

Ref.

No. Part No.

Description

Amt.

Req.

1. 29476XT Feed Drive Assembly 1

2. 50367S Feed Lifter Lever 1

3. SS8660612TP Set Screw 2

4. G51054 Link Pin 1

5. 666-149 Felt Wick 1

6. 29476SJ Feed Bar Subassembly 1

7. 999-215 Snap Ring 2

8. 34306D Double Eccentric 1

9. 22894AD Screw 2

10. 34335 Connecting Rod Link, for feed link 1

11. 34335A Connecting Rod, for differential feed 1

12. 34337 Link Pin.... 1

13. 34337A Pitman Rod 1

14. 34337B Connecting Rod 1

15. 50347T Link Pin.... 1

16. 34337CA Differential Feed Drive Lever 1

17. SS6121010SP Screw 1

18. RC0980615K0 Shim Ring 1

19. 34335D Guide Stud 1

20. 96719 Spring 1

21. 50383Y Bracket 1

22. SS8110422TP SetScrew 1

23. 96865 Dowel Pin, Grooved 1

24. 34337 Link Pin.... 1

25. SS8150822TP SetScrew 1

26. PH0400104U0 Hinge Pin 1

27. 50367T Lever 1

28. 50337AP Knob 1

29. SS8110422TP SetScrew 3

30. B3215470000 Pin 1

31. 50395T Stud 1

32. 999-211E "O" Ring 1

33. 29476TP Cast-off Plate Release Assembly 1

34. 34363C Stop 1

35. 34363B Pawl 1

36. 34363 Pawl Support 1

37. 34363A Spring 1

38. 22894W Screw 1

39. 28B Screw 1

40. 22894BD Set Screw 2

41. 34335H Feed Bar Guide 1

42. 22569G Screw 2

43. 34335D Guide Stud 1

44. 34335J Collar 1

45. 22894X Screw 1

46. 34334A Feed Drive Shaft 1

47. 34336P Link Pin 1

48. 666-149 Felt Wick 1

Technical diagram of a mechanical assembly with numbered components and exploded views

COVERS

FOR

CS122E11, CS132E11, CS125E61, CS125E62,

CS135E61, CS135E62

Ref.

Amt.

No. Part No.

Description

Req.

1. 25S Screw 2

2. 50389 Guide Roller Assembly 1

3. 22561 Screw 8

4. 34786D Guide Roller 2

5. 34786C Bracket, right 2

6. 34786B Bracket, left 2

7. 50389A Mounting Bracket 1

8. 50302 Slide Cover 1

9. 29476UN Throat Plate Support Assembly 1

10. 34367 Rest Bolt 1

11. 97014 Spring.... 1

12. 95685 Screw 1

13. 34367B Safety Latch 1

14. 34780 Throat Plate Support 1

15. 96277 "E" Ring 1

16. 99364L Shank Screw 1

17. 69H Washer 1

18. 50396G Splash Guard 1

19. 22562B Screw 1

20. 99697J Latch Spring 1

21. 22746 Screw, for handle 1

22. 2165D-0.2 Washer 1

23. 50384F Gasket 1

24. 34382W Handle 1

25. C50063N Washer 1

26. 50382HU Cylinder Cover 1

27. 22894AY Set Screw 1

28. 50382JA Hinge, for cylinder cover 1

29. 34382V Pin, for hinge 1

30. 34382UA Gasket, for hinge 1

31. 22541B Screw, for hinge 2

32. 376 Screw 2

33. 34778GD Suction Tube Assembly 1

34. 90 Screw 2

35. 80265 Washer 1

36. 34778GF Bracket 1

37. G50-748D Cover 1

38. 99675QA-400 Spiral Hose 1

39. 671C23 Hose Clamp 1

40. 50301BW Cloth Plate, front 1

41. 50364X Swing Out Cloth Plate Support 1

42. 99301A Screw 1

43. 9937 Nut 1

44. 50364Y Folder Support 1

45. 99356 Stop Screw 2

46. 99350 Screw 1

47. 97127 Cup Spring 2

48. 95 Screw 1

49. 99351 Screw 1

50. 50364S Hinge Plate 1

51. 99392 Screw 1

52. 660-212 Oil Ring 1

53. 29480ARN Treadle Assembly 1

Technical diagram of mechanical assembly with numbered components and exploded views, likely from an engineering or manufacturing context.

COVERS LOWER BED- FRONT

Ref.			Amt.
No.	Part No.	Description	Req.

1. 29476TU Cylinder Cover Assembly 1

2. 22562B Screw 1

3. 99697J Latch Spring 1

4. 22746 Screw, for handle 1

5. 2165D-0.2 Spring Washer, for handle 1

6. 34382W Handle 1

7. 50384F Gasket 1

8. C50063N Washer 1

9. 50382FV Cylinder Cover 1

10. 22894AY Screw 1

11. 50382FU Hinge, for cylinder cover 1

12. 34382V Pin, for hinge 1

13. 22541B Screw, for hinge 2

14. 34382UA Gasket, for hinge 1

*15. 29476TV Throat Plate Support Assembly, for styles CS122H01, CS132H01,

CS125H11, CS125H12, CS135H11, CS135H12 1

*16. 99364L Shank Screw 1

1. 96277 Retaining Ring 1

2. 34380 Throat Plate Support, for styles CS122H01, CS132H01, CS125H11,

CS125H12, CS135H11, CS135H12 1

18A. 34780CA Throat Plate Support, for styles CS122K01, CS132K01 1

18B. 34780CB Throat Plate Support, for styles CS122K02, CS132K02 1

18C. 34380T Throat Plate Support, for styles CS122H21, CS132H21 1

*19. 34367B Safety Latch 1

*20. 95685 Screw 1

*21. 97014 Spring.... 1

1. 34367 Stop Bolt 1

2. 50393EU Plug, for top 1

3. 50382GV Plate Cover 1

4. SS6090420SP Screw, for plate cover 2

5. J79J Screw 2

6. 34381A Support for Slide 1

7. 91 Screw, for support for slide 1

8. 34367A Cover, for throat plate support 1

9. 90 Screw 2

10. 34381B Rest for Slide 1

11. 79 Screw, for rest for slide 1

12. 605C Screw, for material guide, for styles CS122K01, CS132K01 1

13. 34703CA Material Guide, for styles CS122K01, CS132K01 1

14. 605D Screw, for material guides, for styles CS122K02, CS132K02 .... 1

15. 34703B Material Guie, right, for styles CS122K02, CS132K02 .... 1

16. 34703A Material Guide, left, for styles CS122K02, CS132K02 .... 1

17. 50396G Splash Guard, for styles CS122H21, CS132H21 1

18. 69H Washer, for splash guard, for styles CS122H21, CS132H21....1

*NOTE: For the throat plate support numbers 18A., 18B., 18C., asteric items must be ordered separately to make a complete throat plate support assembly.

12B 12A Three Bond: Union Special No. CE65 11 10 7 8 9 3 5 4 6 6 6 6 6 3 2 1

COVERS LOWER BED- MIDDLE

Ref.			Amt.
No.	Part No.	Description	Req.

1. SS4120615SP Screw 4
2. 35082E Plate 1
3. 35082F Gasket 1
4. 34382EA Gasket, for oil reservoir cover 1
5. 34382J Oil Reservoir Cover 1
6. 87 Screw, for oil reservoir cover 12
7. 22548 Screw, for chamber cover 4
8. 56382D Chamber Cover 1
9. 34782C Chamber Cover Gasket 1
10. 50301CP Cloth Plate Assembly 1
11. 22569AH Screw, for cloth plate 3
12. 50382HX Slide Cover, for styles CS122H01, CS122K01 CS122K02, CS132H01, CS132K01, CS132K02.... 1
    12A. 50302D Slide Cover, for styles CS125H11, CS125H12, CS135H11, CS135H12.... 1
    12B. 50302A Slide Cover, for styles CS122H21, CS132H21 1

Three Bonds Union Special No.CEB2 7 8 5 4 3 1 2 3 9 10 11 12 13 14 15 16 12A 12B 13 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 17A 20A

COVERS LOWER BED - REAR

Ref.			Amt.
No.	Part No.	Description	Req.

1.	22585C	Screw	2
2.	34767K	Synchronizer Stop	1
3.	22569C	Screw	4
4.	50395J	Belt Guard	1
5.	22757E	Screw	3
6.	50395U	Spacer Stud	1
7.	SS4090515SP	Screw	3
8.	50382GR	Belt Guard	1
9.	SM4040655SP	Screw	1
10.	43281K	Latch Spring	1
11.	22766	Screw	3
12.	50301BK	Cloth Plate	1
12A.	50364VB	Cloth Plate, for styles CS125H11, CS125H12, CS135H11, CS135H12	1
12B.	50301BX	Cloth Plate, for styles CS122H21, CS132H21	1
13.	22730	Screw, for cloth plate for styles CS122H21, CS132H21	3
14.	34703ZA	Folder Upper, for styles CS122H21, CS132H21	1
15.	34703Z	Folder, for styles CS122H21, CS132H21	1
16.	34703ZB	Folder L, for styles CS122H21, CS132H21	1
17.	29476SA	Swing-Out Cloth Plate Support, for styles CS122H01, CS132H01, CS125H11, CS125H12, CS135H11, CS135H12, CS122K01, CS122K02, CS132K01, CS132K02	1
17A.	29476TA	Swing-Out Cloth Plate Support, for styles CS122H21, CS132H21	1
18.	99301A	Eccentric Screw	1
19.	9937	Nut	1
20.	50364R	Cloth Plate Support, for styles CS122H01, CS132H01, CS125H11, CS125H12, CS135H11, CS135H12, CS122K01, CS122K02, CS132K01, CS132K02	1
20A.	50364Z	Cloth Plate Support, for styles CS122H21, CS132H21	1
21.	99356	Stop Screw	2
22.	99350	Shoulder Screw	1
23.	97127	Spring Washer	2
24.	95	Set Screw	1
25.	50364S	Hinge Plate	1
26.	99351	Screw	1
27.	22548	Screw	3
28.	22715A	Screw, for CS122H01, CS132H01	1
29.	25S	Screw, for CS122H01, CS132H01	1
30.	34703F3	Hemmer, upper, for styles CS122H01, CS132H01	1
31.	34703F1	Hemmer, lower, for styles CS122H01, CS132H01	1
32.	34703FA1	Hemmer, lower, for styles CS122H01, CS132H01	1
33.	TA1100604R0	Plug	1

MODEL	NEEDLE HEAD	PRESSER FOOT ASSEMBLY	THROAT PLATE	FEED DOG MAIN	FEED DOG DIFFERENTAIL
CS125E61-2D40	50318AN40	34720TB40	34724TB40	34705BW	34726TB10
CS125E61-2D48	50318AN48	34720TB48	34724TB48
CS125E61-3D56	50318AN56	34720TB64	34724TB56	34705TB	34726TB16
CS125E61-3D64	50318AN64		34724TB64
CS135E61-2D40	50318AN40	34720TB40	34724TB40	34705BW	34726TB10
CS135E61-2D48	50318AN48	34720TB48	34724TB48
CS135E61-3D56	50318AN56	34720TB64	34724TB56	34705TB	34726TB16
CS135E61-3D64	50318AN64		34724TB64
CS125E62-2D40	50318AN40	34720TB40	34724TB40	34705BW	34726TB10
CS125E62-2D48	50318AN48	34720TB48	34724TB48
CS125E62-3D56	50318AN56	34720TB64	34724TB56	34705TB	34726TB16
CS125E62-3D64	50318AN64		34724TB64
CS135E62-2D40	50318AN40	34720TB40	34724TB40	34705BW	34726TB10
CS135E62-2D48	50318AN48	34720TB48	34724TB48
CS135E62-3D56	50318AN56	34720TB60	34724TB56	34705TB	34726TB16
CS135E62-3D64	50318AN64		34724TB64

SEWING PARTS

FOR

CS122E11, CS125E61, CS125E62,

CS132E11, CS135E61, CS135E62

Ref.

No. Part No.

Description

Amt.

Req.

1. Needle Head, for sewing comb., on two needle machines (see chart).... 1

1A. ---- Needle Head, for sewing comb., on three needle machines (see chart) .... 1

1. SS5060410TP Screw 1

2. 50318AE40 Eyelet, for sewing comb., on two needle machines (see chart) ..... 1

3A. 50318AE56 Eyelet, for sewing comb., on three needle machines (see chart) ..... 1

1. SS8080310SP Screw 3/4

2. 50392G Needle Thread Eyelet 1

3. • • • • • Presser Foot Assembly, forsewing comb., on two needle machines (see chart).... 1

6A. - - - - - Presser Foot Assembly, for sewing comb., on three needle machines (see chart).... 1

1. 50330FP Shank 1

2. SM7040800SL Screw 1

3. 18C1475 Screw 1

4. NM6030001SD Nut 1

5. PH0300164C0 Pin 1

6. 50330FS Screw 1

7. 50330FM40 Presser Foot Bottom, for sewing comb.; CE11-2D40 (see chart) ...... 1

13A. 50330FM48 Presser Foot Bottom, for sewing comb.; CE11-2D48 (see chart) ..... 1

- 50330FM56 Presser Foot Bottom, for sewing comb.; CE11-3D56, CE11-3D64 (see chart) ..... 1

1. 50330FN Yielding Section Shank 1

2. SM4030455SP Screw 1

3. 50330GN Elastic Guide 1

4. 50330GR Yielding Section 1

5. PH0200063C0 Pin.... 1

6. 52730Y Spring.... 1

7. 18C1479 Shoulder Screw 1

8. 50330FR Torsion Spring 1

9. 50330FU Screw 1

10. 87 Screw 2

11. ---- Throat Plate, for two needle machines (see chart) 1

24A. ---- Throat Plate, for three needle machines (see chart) 1

1. 99293 Screw 2

2. • • • • • Main Feed Dog, for two needle machines (see chart) 1

26A. - - - - - Main Feed Dog, for three needle machines (see chart) 1

1. • • • • • Differential Feed Dog, for two needle machines (see chart) 1

27A. - - - - - - Differential Feed Dog, for three needle machines (see chart) 1

MODEL	NEEDLE HEAD	PRESSER FOOT ASSEMBLY	THROAT PLATE	FEED DOG MAIN	FEED DOG DIFFERENTAIL
CS122E11-2D40	50318AN40	34720TB40	34724TB40	34705BW	34726TB10
CS122E11-2D48	50318AN48	34720TB48	34724TB48
CS122E11-3D56	50318AN56	34720TB64	34724TB56	34705TB	34726TB16
CS122E11-3D64	50318AN64		34724TB64
CS132E11-2D40	50318AN40	34720TB40	34724TB40	34705BW	34726TB10
CS132E11-2D48	50318AN48	34720TB48	34724TB48
CS132E11-3D56	50318AN56	34720TB64	34724TB56	34705TB	34726TB16
CS132E11-3D64	50318AN64		34724TB64

SEWING PARTS FOR CS122H01, CS132H01

Ref.			Amt.
No.	Part No.	Description	Req.

1.	----	Needle Head, on two needle machines, (see chart)....	1
1A.	----	Needle Head, on three needle machines, (see chart)....	1
2.	SS5060410SP	Set Screw....	3/4
3.	50318AE40	Eyelet, for 4.0, 4.8 gauges (see chart)....	1
3A.	50318AE56	Eyelet, for 5.6, 6.4 gauges (see chart)....	1
4.	SS6060440TP	Screw....	1
5.	50392G	Needle Thread Eyelet....	1
6.	----	Presser Foot Assembly, for sewing comb., (see chart)....	1
7.	G65-134	Presser Foot Shank....	1
8.	91	Screw....	1
9.	G50-266	Bushing....	2
10.	22716A	Screw....	1
11.	50397A48	Stitch Tongue, for 4.8 gauge....	1
11A.	50397C	Stitch Tongue, for 4.0 gauge....	1
-	50397A16	Stitch Tongue, for 5.6, 6.4 gauges....	1
12.	50330BL16	Presser Foot Bottom....	1
13.	57830A	Yielding Section....	2
14.	6-25-55	Drill Rod....	3
15.	605	Screw....	1
16.	79633	Spring....	1
17.	HT2C	Screw....	1
18.	34703W2.3	Throat Plate Edge Guide....	1
-	34703W4.3	Throat Plate Edge Guide....	1
19.	----	Throat Plate, for two needle machines (see chart)....	1
19A.	----	Throat Plate, for three needle machines (see chart)....	1
20.	87	Screw, for throat plate....	2
21.	99293	Screw, for feed dogs....	1
22.	----	Differential Feed Dog (see chart)....	2
23.	----	Main Feed Dog (see chart)....	1

MODEL	NEEDLE HEAD	PRESSER FOOT ASSEMBLY	THROAT PLATE	FEED DOG MAIN	FEED DOG DIFFERENTAIL
CS122H01-2A40	50318AN40	50320AH	50324BL40	34705F	34726F
CS122H01-2C40			34724F10
CS122H01-2A48	50318AN48	50320T48	50328BL48
CS122H01-2C48			50324F48
CS122H01-3A56	50318AN56	50320T60	50324BL56
CS122H01-3B56			50324BS56
CS122H01-3C56			34724F56
CS122H01-3A64	50318AN64	50320T60	50324BL64
CS122H01-3B64			50324BS64
CS122H01-3C64			34724F64
CS132H01-2A40	50318AN40	50320AH	50324BL40	34705F	34726F
CS132H01-2C40			34724F10
CS132H01-2A48	50318AN48	50320T48	50328BL48
CS132H01-2C48			50324F48
CS132H01-3A56	50318AN56	50320T60	50324BL56
CS132H01-3B56			50324BS56
CS132H01-3C56			34724F56
CS132H01-3A64	50318AN64	50320T60	50324BL64
CS132H01-3B64			50324BS64
CS132H01-3C64			34724F64

Technical diagram of a mechanical assembly with numbered components and a zoomed-in detail view

1A 3A

Technical diagram of a mechanical assembly with numbered components, including a bracket and housing assembly.

17A 17 18

19 20 21 21

SEWING PARTS

FOR

CS125H11, CS125H12, CS135H11, CS135H12

Ref.

No. Part No.

Description

Amt.

Req.

1.

1A.

1. SS8080310TP

2. 50318AE40

3A. 50318AE56

1. SS5060410SP

2. 50392G

3. ---

......

1. G57730GB

2. 91

3. 39568J

4. 61330B41

5. 50330BH40

11A. 50330BH64

1. 34730A

2. G57730GC

3. 22716

4. 96651

5. G57730GD

6. ---

17A. ----

1. 87

2. ---

20.

1. 99293

Needle Head, for two needle machines (see chart pages 50-51) .... 1

Needle Head, for three needle machines (see chart pages 50-51) ..... 1

Screw 1

Needle Eyelet, for 4.0, 4.8 gauges 1

Needle Eyelet, for 5.6, 6.4 gauges 1

Screw 3/4

Needle Thread Eyelet 1

Presser Foot Assembly, for 4.0, 4.8 gauges (see chart pages 50-51) ..... 1

Presser Foot Assembly, for 5.6, 6.4 gauges (see chart pages 50-51) ..... 1

Shank 1

Screw 1

Pressure Spring 1

Pin 1

Presser Foot Bottom, for 4.0, 4.8 gauges 1

Presser Foot Bottom, for 5.6, 6.4 gauges 1

Yielding Section 1

Plate 1

Screw 1

Roll Pin 1

Torsion Spring 1

Throat Plate, for two needle machines (see chart pages 50-51)....1

Throat Plate, for three needle machines (see chart pages 50-51) .... 1

Screw, for throat plates 2

Main Feed Dog (see chart pages 50-51) 1

Differential Feed Dog (see chart pages 50-51) 1

Screw, for feed dogs 2

SEWING CHART

FOR

CS125H11, CS135H11

MODEL	NEEDLE HEAD	PRESSER FOOT ASSEMBLY	THROAT PLATE	FEED DOG MAIN	FEED DOG DIFFERENTAIL
CS125H11-2A40	50318AN40	50320BE40	50324CJ40	34705DG	34726DG
CS125H11-2C40			34724E10
CS125H11-2A48	50318AN48		50324CJ48
CS125H11-2C48			34724E48
CS125H11-3A56	50318AN56	50320BF64	50324CK56
CS125H11-3B56			50324CL56
CS125H11-3C56			34724E56
CS125H11-3A64	50318AN64		50324CK64
CS125H11-3B64			50324CL64
CS125H11-3C64			34724E64
CS135H11-2A40	50318AN40	50320BE40	50324CJ40
CS135H11-2C40			34724E10
CS135H11-2A48	50318AN48		50324CJ48
CS135H11-2C48			34724E48
CS135H11-3A56	50318AN56	50320BF64	50324CK56
CS135H11-3B56			50324CL56
CS135H11-3C56			34724E56
CS135H11-3A64	50318AN64		50324CK64
CS135H11-3B64			50324CL56
CS135H11-3C64			34724E64

SEWING CHART

FOR

CS125H12, CS135H12

MODEL	NEEDLE HEAD	PRESSER FOOT ASSEMBLY	THROAT PLATE	FEED DOG MAIN	FEED DOG DIFFERENTAIL
CS125H12-2A40	50318AN40	50320BE40	50324CJ40	34705DG	34726DG
CS125H12-2C40			34724E10
CS125H12-2A48	50318AN48		50324CJ48
CS125H12-2C48			34724E48
CS125H12-3A56	50318AN56	50320BF64	50324CK56
CS125H12-3B56			50324CL56
CS125H12-3C56			34724E56
CS125H12-3A64	50318AN64		50324CK64
CS125H12-3B64			50324CL64
CS125H12-3C64			34724E64
CS135H12-2A40	50318AN40	50320BE40	50324CJ40
CS135H12-2C40			34724E10
CS135H12-2A48	50318AN48		50324CJ48
CS135H12-2C48			34724E48
CS135H12-3A56	50318AN56	50320BF64	50324CK56
CS135H12-3B56			50324CL56
CS135H12-3C56			34724E56
CS135H12-3A64	50318AN64		50324CK64
CS135H12-3B64			50324CL56
CS135H12-3C64			34724E64

SEWING PARTS

FOR

CS122H21, CS132H21

Ref.

No. Part No.

Description

Amt.

Req.

1. Needle Head, for sewing comb., on two needle machines (see chart) 1

1A. ---- Needle Head, for sewing comb., on three needle machines (see chart).... 1

1. SS6066440TP Screw 1

2. 50318AE40 Eyelet, for 4.0, 4.8 gauges 1

3A. 50318AE56 Eyelet, for 5.6, 6.4 gauges 1

1. SS8080310TP Screw 3/4

2. 50392G Needle Thread Eyelet 1

3. • • • • • Presser Foot Assembly, for sewing comb. (see chart) 1

4. G57730GB Presser Foot Shank 1

5. 91 Screw 1

6. 39568J Spring 1

7. 22716A Screw 1

8. 50397C Stitch Tongue 1

11A. 50397A16 Stitch Tongue 1

1. 61330B42 Drill Rod 1

2. 50330DU64 Presser Foot Bottom 1

3. 34730AT Yielding Section 1

4. G57730GC Plate 1

5. 22716 Screw 1

6. 96651 Roll Pin.... 1

7. G57730GD Spring 1

8. 87 Screw, for throat plate 3

9. 22768 Screw, for throat plate 1

10. ---- Throat Plate, for two needle machines (see chart) 1

21A. ---- Throat Plate, for three needle machines (see chart) 1

1. 99293 Screw, for feed dogs 2

2. Differential Feed Dog (seechart) 1

3. Main Feed Dog (see chart) 1

MODEL	NEEDLE HEAD	PRESSER FOOT ASSEMBLY	THROAT PLATE	FEED DOG MAIN	FEED DOG DIFFERENTAIL
CS122H21-2A40	50318AN40	50320GE40	34724FR40	34705FT	34726FT
CS122H21-2C40			34724FT40
CS122H21-2A48	50318AN48		34724FR48
CS122H21-2C48			34724FT48
CS122H21-3A56	50318AN56	50320BG 64	34724FR56
CS122H21-3B56			34724FS56
CS122H21-3C56			34724FT56
CS122H21-3A64	50318AN64		34724FR64
CS122H21-3B64			34724FS64
CS122H21-3C64			34724FT64
CS132H21-2A40	50318AN40	50320BG 40	34724FR40
CS132H21-2C40			34724FT40
CS132H21-2A48	50318AN48		34724FR48
CS132H21-2C48			34724FT48
CS132H21-3A56	50318AN56	50320BG 64	34724FR56
CS132H21-3B56			34724FS56
CS132H21-3C56			34724FT56
CS132H21-3A64	50318AN64		34724FR64
CS132H21-3B64			34724FS64
CS132H21-3C64			34724FT64

TORQUE: 14-16in.1bs. (1.6-1.8Nm) 1 2 3 4 5 1A 3A TORQUE: 14-16in.1bs. (1.6-1.8Nm)

Technical diagram of a mechanical assembly with numbered components and exploded views

14 15 15A

16 17 18 16 18A

SEWING PARTS

FOR CS122K01, CS122K02

CS132K01, CS132K02

Ref.

No. Part No.

Description

Amt.

Req.

1. Needle Head, for two needle machines (see chart) 1

1A. ---- Needle Head, for three needle machines (see chart) 1

1. SS6066440TP Screw 1

2. 50318AE40 Eyelet, for 4.8 gauge 1

3A. 50318AE56 Eyelet, for 5.6, 6.4 gauges 1

1. SS8080310TP Set Screw 4-6

2. 50392G Needle Thread Eyelet 1

3. • • • • • Presser Foot, for sewing comb., (see chart) 1

4. 31130A Presser Foot Shank 1

5. 91 Screw.... 1

6. 605C Screw 1

7. G11940 Spring 1

8. G65-90 Presser Foot Guide 1

9. 6-25-55 Drill Rod 2

10. 31130RA Yielding Section 2

11. 87 Counter Sunk Head Screw, for throat plate 2

12. ---- Throat Plate, for two needle machines (see chart) 1

15A. ---- Throat Plate, for three needle machines (see chart) 1

1. 99293 Screw, for feed dogs.... 1

2. Main Feed Dog (see chart) 1

3. Differential Feed Dog, for CS122K01, CS132K01 (see chart) 1

18A. Differential Feed Dog, for CS122K02, CS132K02 (see chart) 1

MODEL	NEEDLE HEAD	PRESSER FOOT ASSEMBLY	THROAT PLATE	FEED DOG MAIN	FEED DOG DIFFERENTAIL
CS122K01-2D48	50318AN48	34727CA48	34724CA48	34705CA	34726CA16
CS122K01-2D56	50318AN56	34727CA60	34724CA56
CS122K01-2D64	50318AN64		34724CA64
CS122K02-2D56	50318AN56		34724CB56		34726A
CS122K02-2D64	50318AN64		34724CB64
CS132K01-2D48	50318AN48	34727CA48	34724CA48		34726CA16
CS132K01-2D56	58318AN56	34727CA60	34724CA56
CS132K01-2D64	50318AN64		34724CA64
CS132K02-2D56	50318AN56		34724CB56		34726A
CS132K02-2D64	50318AN64		34724CB64

ACCESSORIES

Ref. No. Part No. Description Amt. Req.

1. 11969557 Thread Stand (5 cones) 1
2. G21201 Screwdriver, for needle head 1
3. 12288403 Thread Tweezer 1
4. 28604R Oil (1 pint) 1
5. 34395 Profile Rubber 1
6. 660-264 "S" Hook 2
7. 421D42 Chain.... 1
8. 51295B Isolator 4
9. 121GJS070/027 Needles.... 1
10. 34321CC Flange Syncronizer 1

Technical diagram of a mechanical assembly with numbered components and exploded view, including 3D wireframe views.

TAPE GUIDE, HOLD DOWN DEVICE

FOR

CS122E11, CS125E61, CS125E62

CS132E11, CS135E61, CS135E62

Ref.

No. Part No.

Description

Amt.

Req.

1. 34786G Tape Guide Assembly 1

2. 96275 Retaining Ring 1

3. 999-30 "O" Ring 2

4. 34786GE Shaft 1

5. 34786GA Tape Guide 1

6. 34786GB Support 1

7. 22894AY Screw 1

8. 34783N Support 1

9. 22894X Screw 1

10. 93A Screw 1

11. 34786GC Bracket 1

12. 95951 Washer 1

13. 999-90B Clamping Lever 1

14. 18 Nut 2

15. 21657E Washer 1

16. 34786GG Roller 1

17. 88B Screw 1

18. 34786GF Collar 1

19. 34731 Hold Down Device Assembly 1

20. 34731D Lever 1

21. 22570B Screw 1

22. 22585C Screw 1

23. 34731C Stop 1

24. 22836 Screw 1

25. 39531B Collar 1

26. 604 Screw 1

27. 97113 Torsion Spring 1

28. 50337BE Material Hold Down Guide 1

29. 39531A Shaft 1

30. 34731A Hold Down Plate 1

31. 77K Screw 2

32. 99391 Spacer Stud 1

33. 18 Nut 1

Three Bond: Union Special No. CE62 Three Bond: Union Special No. CE65 58 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

57 56

UNDER TRIMMER ASSEMBLY

FOR

CS122E11, CS125E61, CS125E62

CS132E11, CS135E61, CS135E62

Amt.

Req.

Ref.

No. Part No.

1. G51347A

2. 93

3. 22874F

4. 50322BH

5. 34738A

6. 99370

7. 29924M

8. 34771G

9. 34771A

10. 666-149

11. 34771B

12. G51054

13. 34771AA

14. 93

15. G51054

16. 34771K

17. 34785

18. 22894BG

19. 34771PA

20. 22729

21. 34770H

22. 34749B

23. 34750EA

24. 22729AB

25. 34750A

26. 34779

27. 22565C

28. 34771L

29. 88

30. 12865

31. 88

32. 34739N

33. 22585R

34. 34739A

35. 96529

36. 51280J

37. 1266001

38. 77L

39. 34771J

40. 34771D

41. 89

42. 99369

43. 96530

44. 34771E

45. 97016

46. 34763B

47. 34763C

48. 97015

49. 34763BA

50. 660-210

51. 22528

52. 34771H

53. J87J

54. 34771C

55. 34771F

56. 34734

57. CO67B

58. 96722

Description

Screw 1

Screw 2

Screw 1

Shaft 1

Spacer 1

Screw 1

Under Trimmer Assembly 1

Slide Block 1

Lever Assembly 1

Wick 2

Connecting Rod 1

Joint Pin 1

Lever 1

Screw 1

Joint Pin 1

Connection 1

Shaft 1

Screw 1

Upper Knife Lever 1

Screw 1

Upper Knife 1

Lower Knife 1

Knife Holder 1

Screw 1

Bushing 1

Edge Guide 1

Screw 1

Lever 1

Screw 2

Collar 1

Screw 2

Housing 1

Screw 1

Bushing 1

Pin 1

Pin 2

Gasket 1

Screw 1

Stop 1

Lever 1

Screw 1

Nut 1

Pin 1

Spring Washer 2

Spring 1

Locking Plate Assembly 1

Bolt 1

Spring 1

Locking Plate 1

Retaining Ring 1

Screw 1

Stop 1

Screw 1

Shaft 1

Pin....1

Shaft, for feed drive 1

Cork Plug 2

Spring 1

Technical diagram of a mechanical assembly with numbered components and exploded view

PULLER LIFTER ASSEMBLY

FOR

CS125E61, CS125E62, CS125H11, CS125H12,

CS135E61, CS13562, CS135H11, CS135H12

Ref.

No. Part No.

Description

Amt.

Req.

1. 50377VA Lever, lifter front 1

2. SS6151440SP Screw 1

3. 29476UX Puller Lifter Assembly 1

4. 59477 Regulator 1

5. 35733G Nut 1

6. 660-212 "O" Ring 1

7. 50377L Spring 1

8. 50377C Lever, lifter 1

9. 50344AT Bushing 2

10. 50377D Bracket, for roller lifter 1

11. SS8150710SP SetScrew 1

12. SS8120410SP Set Screw 1

13. 50337AM Bumper 1

14. 50377AF Pin....1

15. 96529 Pin....1

16. 50377M Lifter 1

17. SS8151150SP Screw 1

18. NS6110310SP Nut 1

19. SS7112420SP Screw 1

20. 50377AM Bar, roller presser 1

21. 50377AR Guide Pin 1

22. SS6121220TP Screw 2

23. 50377T Bushing, lifter link 1

24. RO068190100 "O" Ring 1

25. 50377G Lever, puller lifter 1

Loctite: Union Special No. CE59 Loctite: Union Special No. CE49 18 12 16 14 15 13 17 17 10 9 8 7 6 4 3 2 5 23 24 22 21 25 24 20 23 24 25 22 21 25 24 20 19

PULLER DRIVE ASSEMBLY

FOR

CS125E61, CS125E62, CS125H11, CS125H12,

CS135E61, CS13562, CS135H11, CS135H12

Ref.

No. Part No.

Description

Amt.

Req.

1. 29476SP Puller Drive Assembly 1
2. 50377F Roller Driving Arm 1
3. 660-893 Seal 1
4. 50377S Bushing 1
5. 50377E Lever, Puller Drive 1
6. SS8701042TP Screw 2
7. SS8110422TP Set Screw 1
8. 50377U Housing, Puller Drive 1
9. 50377P Bushing 1
10. TA1450404R0 Rubber Plug 1
11. SS7121610SP Screw 4
12. 50377Z Connecting Rod Eccentric Assembly 1
13. 50377AA Connecting Rod.... 1
14. SS2090620SP Screw 2
15. 50386 Washer 1
16. 50377AB Eccentric 1
17. SS8660612TP Screw 2
18. 50384L Gasket 1
19. 50377J Roller Drive Link Assembly 1
20. SS6122030SP Screw 2
21. 50344AP Bushing, link 2
22. 660-303 Bearing 2
23. NS6120480SP Nut 2
24. WP0501046SC Washer 4
25. 660-1089 Thrust Washer 4

Technical diagram of a mechanical device with numbered components and exploded view, including labeled parts 1 through 10.

1. 50386E Washer, plastic 2

2. 22517 Screw, for lower roller assembly 2

3. 22585C Screw 2

4. 34380C Roller Guard 1

Technical diagram of an industrial mechanical assembly with numbered components for identification

16A 25

Three Bond: Union Special No. CE62 Screw Into Bed

FABRIC TRIMMER ASSEMBLY

FOR CS122H21, CS132H21

Ref.

No. Part No.

Description

Amt.

Req.

1. 29924LA Fabric Trimmer Assembly 1

2. SS7090530SP Screw 1

3. 50372A Knife Lever 1

4. SS7111120TP Screw 1

5. 50370J Upper Knife 1

6. 34785L Shaft 1

7. 34749EL Lower Knife 1

8. 50372B Lower Knife Holder 1

9. 22729ABA Screw 1

10. 34739L Support Block 1

11. 22596 Screw 1

12. 25CC Screw 1

13. 97005D Spring 1

14. 33688 Adjusting Collar 1

15. 22894AY Screw 2

16. 34771SL Lever 1

17. 22894C Screw 2

18. 34336P Link Pin 1

19. 666-149 Oil Wick 1

20. 34771VL Lever 1

21. 22528 Screw 1

22. 9937 Hex Nut 1

23. 4611U Washer 1

24. 34771UL Adjusting Bolt 1

25. 34771TL Connecting Link.... 1

26. 22894Y SetScrew 1

27. 95412 Screw 2

28. 671B115 Suction Tube 1

29. 29480AWK Exhaust Assembly 1

30. 50396L Guard 1

31. 50382JU Sliding Cover, For Guard 1

32. 22807 Screw 1

33. 98A Screw 1

Technical diagram of a mechanical assembly with numbered components for identification

NEEDLE DIPPER (EXTRA SEND CHARGE)

Ref.

No. Part No.

Description

Amt.

Req.

1. 29480AZV Needle Dipper Assembly 1
2. 22562B Screw, for needle dipper 1
3. 80265 Washer 1
4. 50393GW Felt 1
5. 50382KD Needle Dipper Cover 1
6. 666-197 Pin, for oil wick 1
7. 50393KZ Needle Dipper 1
8. CQ20000000 Oil Wick 1

NUMERICAL INDEX OF PARTS

Part No.	Page No.	Part No.	Page No.	Part No.	Page No.	Part No.	Page No.
11071602	21	22836	59	31130RA	55	34381A	39
11071701	21	22874C	33	33688	71	34381B	39
11550209	19	22874F	61	34306D	35	34382EA	41
11638M	69	22875N	19	34321CC	25, 57	34382H	33
11969557	57	22892C	69	34334A	35	34382J	41
12124202	17	22894AD	9, 31	34334S	33	34382UA	37, 39
121GJS070/027	57	22894AD	35, 67	34335	35	34382V	37, 39
12288403	57	22894AY	37, 39	34335A	35	34382W	37, 39
1266001	61	22894AY	59, 71	34335D	35	34390	9
12865	61	22894BD	9, 35	34335G	33	34393D	27
18	59	22894BG	61	34335H	35	34393L	27
18-1470	27	22894C	29, 71	34335J	33, 35	34393M	27
18C1471	17	22894T	31	34336A	33	34394A	9
18C1475	45	22894W	29, 35	34336B	9	34394B	9
18C1479	45	22894X	29, 33	34336C	9	34395	57
21657E	59	22894X	35, 59	34336D	9	34642A	29
2165D-0.2	37, 39	22894Y	71	34336E	9	34682C	27
22503F	33	258A	27	34336N	33	34703A	39
22517	67	25CC	71	34336P	35, 71	34703B	39
22528	61, 71	25S	37, 43	34336Q	33	34703CA	39
22541B	29, 37	28604R	57	34336RA	33	34703F1	43
22541B	39	28B	35	34336S	33	34703F3	43
22548	41, 43	29105BK	29	34336U	33	34703FA1	43
22561	37	29126FW	15	34336V	33	34703W2.3	47
22562	21	29475CG	17	34337	35	34703W4.3	47
22562A	33	29476SA	43	34337A	35	34703Z	43
22562B	37, 39	29476SH	33	34337B	35	34703ZA	43
22562B	73	29476SJ	35	34337CA	35	34703ZB	43
22565C	9, 61	29476SP	65	34337F	33	34709D	29
22569AH	41	29476SS	69	34338	33	34730A	49
22569B	25	29476SW	67	34338B	33	34730AT	53
22569C	43	29476TA	43	34340A	33	34731	59
22569G	35	29476TC	11	34342F	9	34731A	59
22570B	59	29476TH	11	34342G	9	34731C	59
22571E	27	29476TJ	27	34342J	29	34731D	59
22571F	9	29476TK	21	34343C	29	34734	61
22580	31	29476TP	35	34344A	29	34738A	61
22585C	43, 59	29476TR	27	34344D	29	34739A	61
22585C	67	29476TS	27	34344E	29	34739L	71
22585R	61	29476TT	21	34353	33	34739N	61
22652A12	29	29476TU	39	34353A	33	34749B	61
22715A	43	29476TV	39	34358BA	31	34749EL	71
22716	49, 53	29476UA	31	34358CA	31	34750A	61
22716A	47, 53	29476UN	37	34358F	17	34750EA	61
22729	61	29476UV	69	34363	35	34763B	61
22729AB	61	29476UX	63	34363A	35	34763BA	61
22729ABA	71	29476VK	29	34363B	35	34763C	61
22730	43	29476VL	27	34363C	35	34767	67
22738B	33	29476XT	35	34366	31	34767K	43
22743	31	29476XU	67	34367	37, 39	34770H	61
22746	37, 39	29480ARN	37	34367A	39	34771A	61
22757E	43	29480AWK	71	34367B	37, 39	34771AA	61
22766	43	29480AYJ	17	34368	31	34771B	61
22768	53	29480AZV	73	34380	39	34771C	61
22807	71	29924LA	71	34380B	67	34771D	61
22811B	29	29924M	61	34380C	67	34771E	61
22829	9	31130A	55	34380T	39	34771F	61

NUMERICAL INDEX OF PARTS

Part No.	Page No.	Part No.	Page No.	Part No.	Page No.	Part No.	Page No.
34771G	61	50304M	31	50337AP	35	50358X	11
34771H	61	50311C	25	50337AW	23	50360	15
34771J	61	50313T	29	50337BE	59	50360B	15
34771K	61	50314G	29	50342AY	13	50360F	15
34771L	61	50317B	11	50342BD	25	50360G	15
34771PA	61	50317C	23	50342BH	25	50360H	15
34771SL	71	50318AE40	45, 47	50343B	29	50363CK	17
34771TL	71	50318AE40	49	50343C	29	50364R	43
34771UL	71	50318AE40	53, 55	50343RC	29	50364S	37, 43
34771VL	71	50318AE56	45, 47	50344AG	29	50364VB	43
34774	69	50318AE56	49	50344AP	65	50364X	37
34776B	67	50318AE56	53, 55	50344AR	25	50364Y	37
34776F	67	50321J	25	50344AT	63	50364Z	43
34778A	69	50321M	13	50344AV	9	50366	17
34778C	69	50322AF	13	50344BK	9	50366A	17
34778GD	37	50322AH	25	50344BL	9	50366B	17
34778GF	37	50322AN	25	50344BM	29	50366G	17
34779	61	50322AZ	9	50344BN	9	50366J	17
34780	37	50322BB	13	50344BP	9	50366L	17
34780CA	39	50322BF	33	50344BU	9	50367S	35
34780CB	39	50322BG	25	50345W	11	50367T	35
34782C	41	50322BH	61	50346	17	50370F	17
34783N	59	50323P	11	50346A	15	50370J	71
34785	61	50323S	31	50347C	15	50372A	71
34785L	71	50325AB	31	50347E	9	50372B	71
34786B	37	50325AL	31	50347F	9	50375V	69
34786C	37	50325AM	31	50347G	15	50375Y	69
34786D	37	50325AN	31	50347J	15	50377AA	65
34786G	59	50330BH40	49	50347L	9	50377AB	65
34786GA	59	50330BH64	49	50347T	35	50377AC	69
34786GB	59	50330BL16	47	50348	29	50377AD	69
34786GC	59	50330CZ	9	50351A	11	50377AE	69
34786GE	59	50330DU64	53	50352	11	50377AF	63
34786GF	59	50330FM40	45	50354F	11	50377AK	69
34786GG	59	50330FM48	45	50354G	11	50377AM	63
34893	29	50330FM56	45	50354H	9	50377AR	63
35082E	41	50330FN	45	50354J	9	50377AT	67
35082F	41	50330FP	45	50355AM	11	50377C	63
35733G	63	50330FR	45	50355AN	11	50377D	63
36271A	17	50330FS	45	50355AR	21	50377E	65
376	37	50330FU	45	50355AS	69	50377F	65
39531A	59	50330GN	45	50357AA	21	50377G	63
39531B	59	50330GR	45	50357AG	31	50377H	69
39536C	33	50332S	27	50357AH	31	50377J	65
39543E	29	50332U	9	50357AJ	31	50377L	63
39568J	49, 53	50332V	21	50357AK	31	50377M	63
41350X	27	50333H	31	50357AR	17	50377P	65
421D42	57	50333P	21	50357AS	17	50377S	65
43281K	43	50335AF	21	50357AT	17	50377T	63
4611U	71	50335AG	21	50357AV	17	50377U	65
50301BK	43	50335AH	21	50357AW	17	50377VA	63
50301BW	37	50335AP	25	50357AX	17	50377Z	65
50301BX	43	50335AW	15	50357V	17	50378AD	69
50301CP	41	50335BC	25	50357Y	17	50381	21
50302	37	50335BD	13	50358U	17	50381B	21
50302A	41	50335BE	29	50358V	17	50381E	9
50302D	41	50337AM	63	50358W	17	50381F	21

NUMERICAL INDEX OF PARTS

Part No.	Page No.	Part No.	Page No.	Part No.	Page No.	Part No.	Page No.
50381G	21	50393FG	27	61330B41	49	96275	59
50382FU	39	50393FH	27	61330B42	53	96276	27
50382FV	39	50393FK	27	61351C	15	96277	37, 39
50382FW	23	50393GB	27	652C16	17	96278	69
50382FX	23	50393GD	27	660-1014	21	96529	61, 63
50382FY	23	50393GF	9	660-1043	13	96530	61
50382FZ	23	50393GT	27	660-1089	65	96651	49, 53
50382GB	23	50393GU	27	660-210	61	96663	33
50382GM	23	50393GW	73	660-212	23, 27	96667	33
50382GR	43	50393HB	23	660-212	37, 63	96719	35
50382GS	27	50393HE	27	660-264	57	96722	61
50382GV	39	50393HH	17	660-283A	19	96841	9
50382HU	37	50393HN	27	660-303	65	96865	35
50382HX	41	50393HS	11	660-739	15, 21	97005D	71
50382JA	37	50393HV	27	660-893	65	97014	37, 39
50382JL	23	50393JP	11	661-149	69	97015	61
50382JN	23	50393JW	11	661-252	29	97016	61
50382JU	71	50393JY	11	661-253	29	97113	59
50382KD	73	50393JZ	11	661-259B	11	97127	37, 43
50383AD	23	50393KV	27	661-261	13, 25	97137	33
50383AE	23	50393KW	9	661-261	69	98A	17, 71
50383Y	35	50393KZ	73	661-262	13	99293	45, 47, 49
50384F	37, 39	50393LA	27	661-348	25	99293	53, 55
50384L	23, 65	50394AF	11	666-149	35, 61	99301A	37, 43
50386	65	50395J	43	666-149	71	99343	29
50386B	69	50395T	35	666-197	73	99346	29
50386E	67	50395U	43	666-329	11	99349	27
50386L	33	50396G	37, 39	666-330	19	99350	37, 43
50386M	33	50396L	71	666-334	23	99351	37, 43
50389	37	50397A16	47	671B115	71	99352	9
50389A	37	50397A16	53	671C23	37	99356	37, 43
50390L	25	50397A48	47	69H	37, 39	99364L	37, 39
50391	13	50397C	47, 53	77A	31	99369	61
50391A	13	50692G	19	77K	59	9937	29, 33, 37
50392AB	9	51235G	29	77L	61	9937	43, 71
50392AU	17	51280J	61	79	39	99370	61
50392AV	19	51295B	57	79633	47	99391	59
50392AW	17	52730Y	45	80265	37, 73	99392	37
50392AX	17	53678N	15	87	45, 47	99652A	29
50392AY	17	56382D	41	87	53, 55	99658	25
50392AZ	17	56390E	25	87U	17	99675QA-400	37
50392BC	19	56390H	29	88	61	99682XC	23
50392G	45, 47	56392G	19	88B	59	99682XCB	23
50392G	49	56392H	19	89	61	99697J	37, 39
50392G	53, 55	56392M	19	90	37, 39	999-211	9
50392S	17	56392R	19	91	47, 49	999-211B	9
50392T	17	57830A	47	91	53, 55	999-211E	35
50392W	19	57844	17	93	33, 61	999-212-035	9
50392X	19	57865	19	93A	59	999-215	35
50392Y	19	57892K	19	95	43	999-254J	27
50392Z	19	59477	63	95205	25	999-30	59
50393EU	23, 39	6-25-55	47, 55	95406	27	999-90B	59
50393EW	23	604	59	95412	71	B3103804000	19
50393EX	27	6042A	31	95685	37, 39	B3112704000	19
50393EZ	9	605	47	95951	59	B3120352000	19
50393FD	27	605A	17	95953	27	B3120704000	19
50393FE	27	605C	39, 55	96162A	25	B3121804000	19
50393FF	27	605D	39	96162B	15	B3126012000	19

NUMERICAL INDEX OF PARTS

Part No.	Page No.	Part No.	Page No.	Part No.	Page No.
B3215470000 ...	35	SS1110640SL ...	23	SS8150822TP ...	35
B3530555000 ...	23	SS1121010SP ...	17	SS8151150SP ...	63, 69
C50044E ...	17	SS2090620SP ...	65	SS8660512TP ...	15, 29
C50056B ...	21	SS4080620TP ...	11, 31	SS8660612TP ...	9, 13
C50063N ...	37, 39	SS4090515SP ...	43	SS8660612TP ...	15
C50077K ...	69	SS4090815SP ...	17	SS8660612TP ...	25, 27
C50094B ...	27	SS4120615SP ...	17, 23	SS8660612TP ...	35, 65
CE27 ...	11	SS4120615SP ...	41	SS8661012TP ...	13
CE59 ...	11	SS4120915SP ...	17, 19	SS8681412TP ...	13
CE63 ...	11	SS4120915SP ...	23	SS8701042TP ...	65
CE66 ...	21	SS4121215SP ...	23	SS9090640SP ...	15
CO67B ...	61	SS4121615SP ...	23	SS9111010SP ...	69
CO67D ...	29	SS5060410SP ...	47, 49	SS9151740CP ...	21
CQ200000000 ...	73	SS5060410TP ...	45	TA1050504R0 ...	23
CQ25220000 ...	11	SS6060440TP ...	47	TA1100604R0 ...	23, 43
G11940 ...	55	SS6066440TP ...	53, 55	TA1450404R0 ...	65
G21201 ...	57	SS6090420SP ...	39	WP0320501SC ...	31
G29105F ...	29	SS6090440SP ...	11, 31	WP0501046SC ...	65
G29476BV ...	33	SS6090560TP ...	29	WP0742016SP ...	15
G50-266 ...	47	SS6090620SP ...	11	WS0371026SD ...	17
G50-748D ...	37	SS6091022TP ...	29	WS0510002KP ...	17, 69
G51054 ...	35, 61	SS6110610TP ...	21	WZ0641510KP ...	23
G51347A ...	61	SS6121010SP ...	11, 21
G57730GB ...	49, 53	SS6121010SP ...	35
G57730GC ...	49, 53	SS6121220TP ...	63
G57730GD ...	49, 53	SS6122030SP ...	65
G65-134 ...	47	SS6151220SP ...	69
G65-90 ...	55	SS6151440SP ...	63
GA29477AP ...	33	SS6151920SP ...	21
HA20B ...	29	SS6153040SP ...	21
HT2C ...	47	SS7060310SP ...	17, 31
J79J ...	39	SS7080510TP ...	15, 17
J87J ...	33, 61	SS7080520SP ...	11, 31
LA451 ...	23	SS7090520SP ...	19
NM6030001SD ...	45	SS7090530SP ...	23, 71
NS6110310SP ...	63	SS7090610SP ...	17
NS6110420SP ...	19	SS7090910TP ...	17
NS6120480SP ...	65	SS7110410SP ...	17, 69
NS6150310SP ...	21	SS7110910TP ...	15
NS6620320SP ...	23	SS7111120TP ...	11, 13
NS6680410SP ...	15	SS7111120TP ...	71
PH0200063C0 ...	45	SS7112420SP ...	63
PH0300164C0 ...	45	SS7120640SP ...	17, 23
PH0400104U0 ...	35	SS7120710SP ...	17, 27
PS0400142KH ...	9	SS7121410TP ...	15, 19
RC0980615K0 ...	35	SS7121610SP ...	65
RE0500000K0 ...	21	SS7660520SP ...	13
RE0900000K0 ...	31	SS7681410TP ...	13
RO037180100 ...	9	SS8080310SP ...	45
RO068190100 ...	21	SS8080310TP ...	49, 53
RO068190100 ...	63	SS8080310TP ...	55
SD0380551SL ...	17	SS8080410TP ...	17
SD0640323TP ...	23	SS8090540SP ...	31
SD0790303SP ...	21	SS8110422TP ...	11, 15
SD1000801SH ...	15	SS8110422TP ...	21, 35
SM4030455SP ...	45	SS8110422TP ...	65, 69
SM4040655SP ...	43	SS8120410SP ...	63
SM7040800SL ...	45	SS8150710SP ...	63

NOTES

NOTES

UnionSpecialCorporation

Corporate Office

One Union Special Plaza

Huntley, IL 60142

Phone: 847•669•5101

Fax: 847•669•4454

Union Special GmbH

EuropeanDistributionCenter

Raiffeisenstrasse 3

D-71696 Möglingen, Germany

Tel: 49•07141•247•0

Fax: 49•07141•247•100

JUKI CORPORATION

INTERNATIONAL SALES DIVISION

8-2-1, KOKURYO - CHO,