FS132C210MV - Sewing machine Union Special - Free user manual and instructions

USER MANUAL FS132C210MV Union Special

Union Special INDUSTRIAL SEWING EQUIPMENT

ILLUSTRATED PARTS LIST

Differential Feed, Coverseaming Machines Union Special P235-94 QUALITY DESIGN Q D'S SERIES

MANUAL NO. PT9417

STYLES

FS122C200MB

FS122C203MB

FS122C209MX

FS122C209MXA

FS122C210MB

FS122C253MB

FS123C209MX

FS123C209MXA

FS132C200MV

FS132C209MV

FS132C209MVA

FS132C210MV

FS133C200MW

FS133C209MV

FS133C209MVA

Fifth Edition Copyright 1994

By

Union Special Corporation Rights Reserved In All Countries

Printed in U.S.A. October 1994

PREFACE

This parts manual has been prepared to assist you in locating individual parts or assemblies on FS100 Series machines. It can be used in conjunction with Union Special Adjusting Manual IN9302.

It is the desire of Uñlon Special that each machine run at its optimum performance. Parts listed in this manual are designed specifically for your machine and are manufactured with utmost precision to assure long lasting service.

This manual has been comprised on the basis of available information. Changes in design and/or improvements may incorporate a slight modification of configuration in illustrations or part numbers.

On the following pages are illustrations and terminology used in describing the parts used on FS100 Series machines.

INSTRUCTIONS

SAFETY RULES

The sewing machines described in this instruction manual are prohibited from being put into service until it has been ascertained that the sewing units, in which these sewing machines will be built-in have conformed with the EC Council Directives (89/392/EEC, Annex II B).

1. Before putting the machines described in this manual into service, carefully read the instructions. The starting of each machine is only permitted after taking notice of the instructions and by qualified operators.
   IMPORTANT! Before putting the machine into service, also read the safety rules and instruction from the motor supplier.
2. Observe the national safety rules valid for your country.
3. Each machine is only allowed to be used as foreseen. The foreseen use of the particular machine is described in paragraph "STYLES OF MACHINES" of this instruction manual. Another use, going beyond the description, is not as foreseen.
4. All safety devices must be in position when the machine is ready for work or in operation. Operation of the machine without the appertaining safety devices is prohibited.
5. Wear safety glasses.
6. In case of machine conversions and changes all valid safety rules must be considered. Conversions and changes are made at your own risk.
7. The warning hints in the instructions are marked with one of these two symbols:

8.1 For threading needle(s), looper, spreader etc.
8.2 For replacing sewing parts such as needle, presser foot, throat plate, looper, spreader, feed dog, needle guard, folder, fabric guide etc.
8.3 When leaving the workplace and when the workplace is unattended.
8.4 For maintenance work.
8.5 When using clutch motors without actuation lock, wait until the motor is stopped totally.

1. For the following the machine has to be disconnected from the power supply by turning off the main switch or by pulling out the main plug:
2. Maintenance, repair and conversion work (see item 8) must be done only by trained technicians or special skilled personnel under consideration of the instructions.
3. Any work on the electrical equipment must be done by an electrician or under direction and supervision of special skilled personnel.
4. Work on parts and equipment under electrical tension is not permitted. Permissible exceptions are described in the applicable sections of standard sheet DIN VDE 0105.
5. Before doing maintenance and repair work on the pneumatic equipment, the machine has to be disconnected from the compressed air supply. In case of existing residual air pressure after disconnecting from compressed air supply (e.g. pneumatic equipment with air tank), the pressure has to be removed by bleeding.
   * Exceptions are only allowed for adjusting work and function checks done by special skilled personnel.

CAUTION AREAS

CAUTION P250-94 WEAR SAFETY GLASSES, DO NOT TAMPER WITH SAFETY SHIELD. USE WITHOUT SHIELD MAY CAUSE INJURY. CAUTION P250-94 KEEP NEEDLE BAR GUARD IN PLACE CAUTION DO NOT OPERATE MACHINE WITHOUT THIS BELT GUARD IN PLACE CAUTION P250-94 KEEP BELT GUARD IN PLACE CAUTION P250-94 KEEP COVER CLOSED DURING OPERATION P250-94

CONTENTS

• IDENTIFICATION OF MACHINES....6

-CLASS DESCRIPTION....6

•MACHINE STYLES 6

•MACHINE STYLES (CONT.) 7

-NEEDLES 8

-TERMS 8

•ILLUSTRATIONS 8

• IDENTIFYING PARTS....9

•NOTES 10

EXPLODED VIEWS

• MAIN FRAME, CAST-OFF PLATE & MISCELLANEOUS COVERS 13

- MAIN FRAME, CAST-OFF PLATE & MISCELLANEOUS COVERS (CONT.) 15

- MAIN FRAME, BUSHINGS, OIL SIGHT GAUGE & MISCELLANEOUS OILING PARTS (ALL GAUGES) ..... 17

- CRANKSHAFT, NEEDLE LEVER, NEEDLE BAR & LOOPER DRIVING PARTS....19

- CRANKSHAFT, NEEDLE LEVER, NEEDLE BAR & LOOPER DRIVING PARTS (CONT.) 21

-SPREADER & SPREADER DRIVE FOR STYLES: FS123C209MXA, FS132C200MV, FS132C209MV, FS132C209MVA, FS132C210MV, FS133C200MW, FS133C209MV, FS133C209MVA (ALL GAUGES) 23

-SPREADER & SPREADER DRIVE (CONT.) FOR STYLES: FS123C209MXA, FS132C200MV, FS132C209MV, FS132C209MVA, FS132C210MV, FS133C200MW, FS133C209MV, FS133C209MVA (ALL GAUGES) 25

-LOOPER ROCKER & CONNECTING ROD PARTS (ALL GAUGES) 27

•MAIN & DIFFERENTIAL FEED MECHANISMS (ALL GAUGES) 29

• MAIN & DIFFERENTIAL FEED MECHANISMS (CONT.) 31

•LIFTER LEVER PARTS (ALL GAUGES) 33

- THREAD TENSION 35

•COVERS & MISCELLANEOUS PARTS (ALL GAUGES) 37

- COVERS & MISCELLANEOUS PARTS (CONT.) (ALL GAUGES) 39

-FAST ACTION TAPE CUTTER, THROAT PLATE SUPPORT & COVERS FOR STYLES: FS122C209MX, FS122C209MXA, FS123C209MX, FS123C209MXA, FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA (ALL GAUGES)....41

•PRESSER FOOT, THROAT PLATE & FEED DOG PARTS 43

•PRESSER FOOT, THROAT PLATE & FEED DOG PARTS (CONT.) 45

•PRESSER FOOT, THROAT PLATE & FEED DOG PARTS (CONT.) 47

-STEPPER MOTOR METERING DEVICE & SYNCHRONIZER KIT FOR STYLE: FS122C253MB (ALL GAUGES) 49

-PNEUMATIC KNEE ACTUATOR & REGULATOR FOR STYLES: FS122C210MB(ALL GAUGES) 51

- MANUAL TAPE CUTTER ASSEMBLY FOR STYLES: FS122C203MB, FS122C253MB (ALL GAUGES) 53

•PNEUMATIC TAPE CUTTER ASSEMBLY FOR STYLES: FS122C210MB, FS132C210MV (ALL GAUGES) 55

-KNEE PRESS AND CONTROL BOX FOR STYLES: FS122C209MX, FS132C209MV, (ALL GAUGES), FS123C209MX, FS133C209MV, (.060 GAUGE) ....57

- THREAD STAND & MISCELLANEOUS ACCESSORIES (ALL GAUGES) 59

•TAPE REEL ASSEMBLIES....60

•NOTES 61

• NUMERICAL INDEX OF PARTS 62

•NUMERICAL INDEX OF PARTS 63

•NOTES 64

•NOTES 65

IDENTIFICATION OF MACHINES

Each Union Special machine carries a style number, which on this class machine is stamped in the style plate affixed to the right front of the machine.

The serial number is stamped in the casting at the right rear base of machine.

CLASS DESCRIPTION

Advanced high speed, medium duty, flat bed machine. Two and three needle, one looper, one spreader (on designated styles), offset or tandem top adjusted differential feed, enclosed automatic lubricating system. Recommended needle type 121 GBS. Maximum recommended speed 5500 R.P.M. (Depending on operation). Maximum work space to right of needle bar, 8 1/4" (209.6mm).

MACHINE STYLES

FS122C200MB	COLLARETTE: Two needle, differential feed machine, medium capacity - Typical application- For attaching flat or ribbed knit borders to the neck, arm and leg openings of knit garmentsand similar operations. Seam specifications 406 BSb-1. Standard Gauge Numbers 032 [1/8",3.2mm], 040 [5/32", 4.0mm] and 044 [11/64", 4.4mm]. Maximum recommended speed 5500R.P.M. Recommended needle 121GBS, size 080/032.
FS122C203MB	COLLARETTE: Two needle, differential feed machine, medium capacity with manual tapecutter - Typical application - For attaching ribbed knit borders to the neck, arm and leg openingsof knit garments and similar operations. Seam specifications 406 BSb-1. Standard GaugeNumbers 032 [1/8", 3.2mm], 040 [5/32", 4.0mm] and 044 [11/64", 4.4mm]. Maximumrecommended speed 5500 R.P.M. Recommended needle 121GBS, size 080/032.
FS122C209MX	COLLARETTE: Two needle, differential feed machine, medium capacity, with "Fast-Action"binding cutter, close to rear foot with knee press and control box - Typical application - Forattaching ribbed knit borders to the neck, arm and leg openings of knit garments and similaroperations. Seam specifications 406 BSb-1. Standard Gauge Numbers 032 [1/8", 3.2mm], 040[5/32", 4.0mm] and 044 [11/64", 4.4mm]. Maximum recommended speed 5500 R.P.M.Recommended needle 121GBS, size 080/032.
FS122C209MXA	COLLARETTE: Two needle, differential feed machine, medium capacity with "Fast-Action"binding cutter close to rear foot - Typical application - For attaching knit borders to the neck,arm and leg openings of knit garments and similar operations. Requires workstation numberWS42800BK6A. Seam specifications 406 BSb-1. Standard Gauge Numbers 032 [1/8", 3.2mm],040 [5/32", 4.0mm] and 044 [11/64", 4.4mm]. Maximum recommended speed 5500 R.P.M.Recommended needle 121GBS, size 080/032.
FS122C210MB	COLLARETTE: Two needle, differential feed machine, medium capacity with pneumatic tapecutter - Typical application - For attaching ribbed knit borders to the neck, arm and leg openingsof knit garments and similar operations. Seam specifications 406 BSb-1. Standard GaugeNumbers 032 [1/8", 3.2mm], 040 [5/32", 4.0mm] and 044 [11/64", 4.4mm]. Maximumrecommended speed 5500R.P.M. Recommended needle 121GBS, size 080/032.
FS122C253MB	COLLARETTE: Two needle, differential feed machine, medium capacity with lower elasticmetering device and manual tape cutter - Typical application - For inserting elastic and attachingflat or ribbed knit split-tube borders to the leg openings of men's knit briefs and similaroperations. Seam specifications 406 BSb-1. Standard Gauge Numbers 032 [1/8", 3.2mm], 040[5/32", 4.0mm] and 044 [11/64", 4.4mm]. Maximum recommended speed 5500 R.P.M.Recommended needle 121GBS, size 080/032.
FS123C209MXA	COLLARETTE: Three needle, differential feed machine, medium capacity with "Fast-Action" binding cutter, close to rear foot - Typical application - For attaching ribbed knit borders to the neck, arm and leg openings of knit garments and similar operations. Requires workstation number WS42800BK6A. Seam specifications 407 BSb-1. Standard Gauge Number 060 [15/64", 6.0mm]. Maximum recommended speed 5500 R.P.M. Recommended needle 121GBS, size 080/032.
FS132C200MV	COLLARETTE: Two needle, differential feed, top cover thread machine, medium capacity - Typical application - For attaching ribbed knit borders to the neck, arm and leg openings of knit garments and similar operations. Seam specifications 602 BSb-1. Standard Gauge Numbers 032 [1/8", 3.2mm], 040 [5/32", 4.0mm] and 044 [11/64", 4.4mm]. Maximum recommended speed 5500 R.P.M. Recommended needle 121GBS, size 080/032.
FS132C209MV	COLLARETTE: Two needle, differential feed, top cover thread machine, medium capacity with "Fast-Action" binding cutter close to rear foot with knee press and control box - Typical application - For attaching ribbed knit borders to the neck, arm and leg openings of knit garments and similar operations. Seam specifications 602 BSb-1. Standard Gauge Numbers 032 [1/8", 3.2mm], 040 [5/32", 4.0mm] and 044 [11/64", 4.4mm]. Maximum recommended speed 5500 R.P.M . Recommended needle 121GBS, size 080/032.
FS132C209MVA	COLLARETTE: Two needle, differential feed, top cover thread machine, medium capacity with "Fast-Action" binding cutter close to rear foot - Typical application - For attaching ribbed knit borders to the neck, arm and leg openings of knit garments and similar operations. Requires workstation number WS42800BK6A. Seam specifications 602 BSb-1. Standard Gauge Numbers 032 [1/8", 3.2mm], 040 [5/32", 4.0mm] and 044 [11/64", 4.4mm]. Maximum recommended speed 5500 R.P.M. Recommended needle 121GBS, size 080/032.
FS 132C210MV	COLLARETTE: Two needle, differential feed, top cover thread machine, medium capacity with pneumatic tape cutter- Typical application - For attaching ribbed knit borders to the neck, arm and leg openings of knit garments and similar operations. Seam specifications 602 BSb-1. Standard Gauge Numbers 032 [1/8", 3.2mm], 040 [5/32", 4.0mm] and 044 [11/64", 4.4mm]. Maximum recommended speed 5500 R.P.M.Recommended needle 121GBS, size 080/032.
FS133C200MW	COLLARETTE: Three needle, differential feed, top cover thread machine, medium capacity - Typical application - For attaching flat or ribbed knit split-tube borders to the leg openings on boy's knit briefs. Seam specifications 605 BSb-1. Standard Gauge Number 060 [15/64", 6.0mm]. Maximum recommended speed 5500 R.P.M. Recommended needle 121GBS, size 080/032.
FS133C209MV	COLLARETTE: Three needle, differential feed, top cover thread machine, medium capacity, "Fast-Action" binding cutter close to rear foot with knee press and control box - Typical application - For attaching flat or ribbed knit borders to the neck, arm and leg openings of knit garments and similar operations: 'Seam specifications 605 BSa-1. Standard Gauge Number 060 [15/64", 6.0mm]. Maximum recommended speed 5500 R.P.M. Recommended needle 121GBS, size 080/032.
FS133C209MVA	COLLARETTE: Three needle, differential feed, top cover thread machine, medium capacity with "Fast-Action" binding cutter close to rear foot - Typical application - For attaching ribbed knit borders to the neck, arm and leg openings of knit garments and similar operations. Requires workstation number WS42800BK6A. Seam specifications 605 BSb-1. Standard Gauge Number 060 [15/64", 6.0mm]. Maximum recommended speed 5500 R.P.M. Recommended needle 121GBS, size 080/032.

NEEDLES

Each needle has both a type and size number. The type number denotes the kind of shank, point, length, groove, finish and other details. The size number, stamped on the needle shank, denotes the largest diameter of the blade measured between the shank and the eye. Collectively, the type number and size number represent the complete symbol which is given on the label of all needles packed and sold by Union Special.

TYPE

DESCRIPTION

121 GBS Round shank, round point, short, single groove, struck groove, spotted, ball point, chromium plated. Sizes available 065/025, 070/027, 075/029, 080/032, 090/036, 100/040.

When changing the needle, make sure it is fully inserted in the needle head before the screw is tightened.

To have needles promptly and accurately filled, an empty package, a needle sample, or the type and size number should be forwarded. Use the description on the label. A complete order should read as follows: "100 needles, type 121 GBS, size 070/027".

TERMS

Prices are net cash and subject to change without notice. All shipments are forwarded F.O.B. shipping point. A charge is made to cover postage and insurance.

ILLUSTRATIONS

This manual has been arranged to simplify ordering repair parts. Exploded views of various sections of the mechanism are shown so that the parts may be seen in their actual position in the machine. On the page opposite the illustration will be found a listing of the parts with their part numbers, description and the number of pieces required in the particular view being shown.

Numbers in the first column are reference numbers only, and merely indicate the position of the part in the illustration. The reference number should never be used in ordering parts. Always use the part number listed in the second column.

Component parts of sub-assemblies which can be furnished for repairs are indicated by indenting their descriptions under the description of the main sub-assembly. As an example refer to the following text.

1. 29126EC Upper Looper Drive Shaft Assembly 1
2. 22503F Screw 1
3. 39543E Cam Follower Locking Clamp 1

It will be noted in the previous example that the cam follower, bushing, cam guide, and the upper looper drive shaft are not listed. The reason is that replacement of these parts individually is not recommended, so the complete upper looper drive shaft assembly should be ordered.

When a part is common to all machines covered in this manual, no specific usage will be mentioned in the description. However, when the parts for the various machines are not the same, the specific usage will be mentioned in the description and, if necessary, the difference will be shown in the illustration.

A numerical index of all the parts shown in this manual is located at the back. This will facilitate locating the illustration and description when only a part number is known.

IDENTIFYING PARTS

Where the construction permits, each part is stamped with its part number. On some of the smaller parts and on those where construction does not permit, an identification letter is stamped in, to distinguish the part from similar ones.

PLEASE NOTE:

Part numbers represent the same part, regardless of which manual they appear in. On all orders please include part number, name and style of machine for which the part was ordered.

NOTES

EXPLODED VIEWS...

Technical diagram of a mechanical device with numbered components and exploded views, including parts like motors, gears, and housing.

MAIN FRAME, CAST-OFF PLATE & MISCELLANEOUS COVERS

Ref.No.	Part No.	Description	Amt.Req.
1.	56382Y	Block, for oil drip plate	1
2.	56382AB	Oil Drip Plate	1
3.	56382AV	Gasket, for looper drive shaft cover	1
4.	56382J	Cover, for looper drive shaft	1
5.	22829	Screw, for looper drive shaft cover	2
6.	56382AA	Oil Reservoir Cover, back	1
7.	22848	Screw, for oil reservoir cover, back	8
8.	22524	Screw, for oil drip plate	2
9.	56382AU	Gasket, for oil reservoir cover, back	1
10.	22548	Screw, for crank chamber cover, lower	4
11.	56382D	Crank Chamber Cover, lower	1
12.	56382AX	Gasket, for crank chamber cover, lower	1
13.	57795B	Synchronizer Bracket, for Style FS122C253MB all gauges	1
14.	660-1002	Plug, for crank chamber cover, upper	1
15.	22541C	Screw, for crank chamber cover, upper	4
16.	57782M	Crank Chamber Cover, upper	1
17.	56382C	Gasket, for crank chamber cover, upper	1
18.	90	Screw, for bearing oiler assembly	2
19.	56382AC	Bearing Oiler Assembly	1
20.	22539S	Plug Screw, for bed	1
21.	80557	Washer, for tension assembly (see page 35)	2
22.	22839C	Screw, for tension assembly (see page 35)	2
23.	21375CE	Belt Guard	1
24.	22829	Screw, for belt guard	2
25.	98A	Screw, for looper guard thread eyelet	2
26.	158B	Looper Thread Eyelet	1
27.	52904B	Retaining Finger	1
28.	52804E	Retainer Support	1
29.	22768	Screw, for retaining finger support	1
30.	87U	Screw, for retainer support	1
31.	52904E	Retaining Finger Support	1
32.	50-216BLK	Pin	1
33.	22516	Screw, for retaining finger	1
34.	73A	Screw, for cast off wire	1
35.	22569C	Screw, for support plate	2
36.	69H	Washer, for support plate screw	2
37.	57757B	Cast-Off Plate	1
38.	52958D	Looper Thread Take-Up Eyelet	2
39.	73A	Screw, for take-up eyelet	2
40.	52904G	Cast-Off Wire	1
41.	22585A	Screw	1
42.	20	Washer	1
43.	53758	Looper Thread Eyelet	1
44.	22848	Screw, for lubricator bracket	1
45.	20	Washer, for lubricator bracket	2
46.	57894D	Eyelet, for needle thread lubricator	1
47.	22889H	Adapter Screw, for needle thread frame eyelet	1
48.	95	Screw	1
49.	57844C	Eyelet, for mounting plate, for Styles FS132C200MV, FS132C209MV, FS132C209MVA, FS132C210MV, all gauges, FS133C209MV, FS133C209MVA, FS133C200MW, .060gauge	1
50.	57858	Spreader Thread Eyelet, for Styles FS132C210MV, all gauges, FS133C200MW060	1
51.	57882J	Guard, for needle lever eyelet	1

1. thru 82. See following page

Technical diagram of a mechanical assembly with numbered components and exploded views, labeled P227-94.

MAIN FRAME, CAST-OFF PLATE & MISCELLANEOUS COVERS (CONT.)

Ref.

Amt.

No. Part No.

Description

Req.

1. thru 51. See preceding page

52.	22585C	Screw	1
53.	57892H	Nut, for spreader thread post, for Styles FS132C200MV, FS132C209MV, FS132C209MVA, FS132C210MV, FS133C200MW, FS133C209MV, FS133C209MVA, all gauges	1
54.	57892C5	Spreader Tension Spring, for Styles FS132C200MV, FS132C209MV, FS132C209MVA, FS132C210MV, FS133C200MW, FS133C209MV, FS133C209MVA, all gauges	1
55.	80665F	Disk, for tension post, for Styles FS132C200MV, FS132C209MV, FS132C209MVA, all gauges, FS133C200MW, FS133C209MV, FS133C200MVA, .060 gauge	2
56.	57892J	Spreader Tension Post, for Styles FS132C200MV, FS132C209MV, FS132C209MVA, FS132C210MV, FS133C200MW, FS133C209MV, FS133C209MVA, all gauges	1
57.	57844	Spreader Thread Guide, for Styles FS132C200MV, FS132C209MV, FS132C209MVA, FS132C210MV, FS133C200MW, FS133C209MV, FS133C209MVA, all gauges	1
58.	34758	Needle Thread Guide	1
59.	57858A	Thread Guide Spring	1
60.	22542	Screw, for spreader thread guide	2
61.	57844A	Spreader Thread Guide, for Styles FS132C200MV, FS132C210MV, FS133C200MW, all gauges	1
62.	34844	Mounting Bracket, for Styles FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA, all gauges	1
63.	77	Screw, for spreader thread guide	1
64.	50373CQ	Spreader Thread Guide, for Styles FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA, all gauges	1
65.	57944B	Needle Thread Guide, all Styles except FS122C209MX, FS122C209MXA, FS123C209MX, FS123C209MXA, FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA, all gauges	1
66.	605A	Screw, for needle thread guide	2
67.	22541C	Screw, for head cover	2
68.	57882K	Head Cover	1
69.	22539AB	Plug Screw, for head cover	1
70.	22851D	Screw, for head cover	2
71.	57882P	Gasket, for head cover	1
72.	22564B	Screw, for guide plate	4
73.	34831C	Guide plate	2
74.	22894Y	Set Screw	1
75.	22539AA	Plug Screw, for bed	1
76.	22585A	Screw, for eyelet guard	1
77.	57770	Needle Thread Take-Up	1
78.	33795	Guard, for needle thread eyelet	1
79.	22894E	Screw, for needle lever stud	2
80.	660-617	Gasket, for needle lever eyelet	1
81.	99682XCA	Guard, for needle break	1
82.	21695R	Sewing Protector	1

Technical diagram of a mechanical assembly with numbered components and labeled parts, including parts like engine, motors, and gears.

MAIN FRAME, BUSHINGS, OIL SIGHT GAUGE & MISCELLANEOUS OILING PARTS (ALL GAUGES)

Ref. No.	Part No.	Description	Amt. Req.
1.	59493A	Base Oil Pump Assembly	1
2.	660-230	Gasket	1
3.	258A	Nut	1
4.	666-214	Felt Intake	1
5.	57849	Bushing, for spreader rocker shaft	2
6.	CL-21	Oil Wick	1
7.	56390H	Thrust Washer	4
8.	56390J	Pilot Ring	2
9.	660-665	Needle Thrust Bearing	2
10.	52883R	Bushing, for presser foot lifter	1
11.	21657X	Release Bushing	1
12.	22569B	Screw, for crankshaft bushing housing	3
13.	57890B	Crankshaft Bushing Housing	1
14.	56390E	Gasket, housing	1
15.	22539R	Oil Drain Plug	1
16.	51-902BLK	Oil Sight Gauge	1
17.	23439G	Strip Tension Assembly	1
18.	23439F	Adjustable Pin	2
19.	188D	Screw	2
20.	51-561BLK	Guide	1
21.	907	Nut	2
22.	627A	Screw	2
23.	20	Washer	2
24.	50392D	Bushing	2
25.	57894	Oil Deflector	1
26.	90	Screw, for oil deflector	2
27.	999-216K	Plug	1
28.	52942AB	Bushing, for looper drive lever shaft, front	2
29.	50-895BLK	Bushing, for looper rocker shaft	1
30.	56393P	Felt, base, front	1
31.	666-259	Felt	1
32.	56390	Main Shaft Bushing, left	1
33.	57836B	Bushing, for feed rocker shaft	2
34.	57842B	Bushing, for looper drive shaft, rear	1
35.	56190	Main Shaft Bushing, middle	1
36.	35897BV	Filter, for main shaft bushing	1
37.	56393Q	Felt, base, rear	1
38.	56390G	Main Shaft Bushing, right	1
39.	57893	Oil Pump Assembly, head	1
40.	57893A	Oil Tube	1
41.	666-214	Felt Intake	1
42.	660-739	Oil Seal	1
43.	51257AA	Presser Bar Bushing	1
44.	57847B	Spreader Bushing	1
45.	57854	Needle Bar Bushing, lower	1
46.	661-258	Plug, for spreader bushing, for Styles FS122C200MB, FS122C203MB, FS122C209MX, FS122C209MXA, FS122C210MB, FS122C253MB, FS123C209MX..	1
47.	57893C	Oil Tube	1
48.	6-67-125	Felt	1
49.	56393W	Felt Oil Attraction	1
50.	22585A	Screw, for clamp	1
51.	660-406	Clamp, for oil tube	1
52.	51154E	Needle Bar Bushing, upper	1

1 2 3 4 5 6 7 8 No. 3 As viewed from the side 67 66 65 64 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 TORQUE: 19-21 in. Ibs. 2.1-2.3 Nm TORQUE: 24-26 in. Ibs. (2.7-2.9 Nm) TORQUE: 38 in. Ibs. (4.3 Nm) 27 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 44 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 P229-94 TORQUE: Ref. No. 42, 43, 44 19-21 in. Ibs. 2.1-2.3 Nm NOTE: See "Aligning main shaft to crankshaft" in adjusting manual! for torque sequence

CRANKSHAFT, NEEDLE LEVER, NEEDLE BAR & LOOPER DRIVING PARTS

Ref.			Amt.
No.	Part No.	Description	Req.

1. 22586R Screw, for needle lever assembly .... 1
2. 56382AK Gasket, for thrust collar 1
3. 51250D Washer 1
4. 51250V Washer 1
5. 660-625 "O" Ring 1
6. 56350J Collar 1
7. 56350K Torlon Washer 1
8. 29348AF Needle Lever Assembly 1
9. 56315A Needle Lever 1
10. 56350G Bushing 1
11. 77 Screw 1
12. 56354D Link, for needle bar 1
13. 51254K Needle Bar Connection .... 1
14. 22562A Screw 1
15. 22564 Screw 1
16. 660-215 Retaining Ring 4
17. 52336A Link Pin 2
18. WO-3 Oil Wick 2
19. 56350D Needle Lever Stud 1
20. 660-625 "O" Ring 1
21. 22768 Screw, for needle lever eyelet 1
22. 54458-9 Needle Lever Thread Eyelet 1
23. 29105BC Ball Joint, for needle lever 1
24. 22559G Screw, for ball joint 2
25. 51216N Washer, for ball joint 1
26. 51216P Nut, for ball joint 1
27. 56316 Needle Lever Connecting Rod 2
28. 61321L Retaining Plate 1
29. 22574 Screw, for handwheel 3
30. 57821D Handwheel 1
31. 56321S Pulley, for synchronizer 1
32. 22894AB Screw, for pulley 2
33. 660-206 Oil Seal Ring, for pulley 1
34. 660-202 "O" Ring 1
35. 29476NZ Crankshaft Assembly 1
36. 51216M Needle Bearing 28
37. 56316C Connecting Rod Guide .... 1
38. 12934A Nut, for connecting rod guide .... 1
39. 57893 Oil Pump Assembly, head (see page 17, ref. no. 39) 1
40. 59493A Oil Pump Assembly, base (see page 17, ref. no. 1) 1
41. 56343F Coupling, for looper drive lever coupling 2
42. 22653L-8 Screw, for looper drive lever coupling 4
43. 22894C Set Screw, for looper drive lever coupling 2
44. 22894D Spot Screw, for looper drive lever coupling 2
45. 29105BB Looper Lever Crank Assembly 1
46. 22587K Screw 2
47. 56343C Ball Joint Guide .... 1
48. 56343E Oil Splasher 1

49. 22729AB Screw 2

50. thru 67. See following page

1 2 3 4 5 6 7 8 No. 3 As viewed from the side 67 66 65 64 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 TORQUE: 19-21 in. lbs. 2.1-2.3 Nm TORQUE: 24-26 in. lbs. (2.7-2.9 Nm) TORQUE: 38 in. lbs. (4.3 Nm) 27 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 PZ29-94 TORQUE: 19-21 in. lbs. 2.1-2.3 Nm NOTE: Cut-out in Ref. No. 39 & 40 to be up when assembling TORQUE: Ref. No. 42, 43, 44 19-21 in. lbs. 2.1-2.3 Nm NOTE: See "Aligning main shaft to crankshaft" in adjusting manual for torque sequence

CRANKSHAFT, NEEDLE LEVER, NEEDLE BAR & LOOPER DRIVING PARTS (CONT.)

Ref.

No. Part No.

Description

Amt.

Req.

1. thru 49. See preceding page

50.	52942AF	Looper Drive Lever Rocker Shaft	1
51.	34342J	Binder Clamp	1
52.	22652A12	Hex Screw	1
53.	57849C	Thrust Washer	1
54.	660-202	"O" Ring	1
55.	56390H	Washer	1
56.	52951C	Thrust Washer	1
57.	56342K	Looper Drive Lever	1
58.	CL-21	Oil Wick	1
59.	57818A060	Needle Head, for all 3 needle, .060 gauge machines	1
	57818A040	Needle Head, for all 2 needle, .040 gauge machines	1
	57818A044	Needle Head, for all 2 needle, .044 gauge machines	1
59A.	57818A032	Needle Head, for all 2 needle, .032 gauge machines	1
60.	28B	Screw, for needle head	2 or 3*
61.	34818B	Cover Thread Guide, for Styles FS132C200MV, FS132C209MV, FS132C209MVA, FS132C210MV, FS133C200MW, FS133C209MV, FS133C209MVA, all gauges	1
62.	99331A	Screw, for cover thread guide, for Styles FS132C200MV, FS132C209MV, FS132C209MVA, FS132C209MVA, FS132C210MV, FS133C200MW, FS133C209MV, FS133C209MVA, all gauges	1
63.	95262V	Nut, for screw, for Styles FS132C200MV, FS132C209MV, FS132C209MVA, FS132C210MV, FS133C200MW, FS133C209MV, FS133C209MVA, all gauges	1
64.	34317	Needle Bar	1
65.	27-435BLK	Washer, for needle bar thread	1
66.	56958A	Needle Bar Thread Eyelet	1
67.	22768	Screw, for needle bar eyelet	1

* Three screws to be used on all .060 gauge machines.

Technical diagram of a mechanical assembly with numbered components and torque specifications in Chinese

P070-93

SPREADER & SPREADER DRIVE
FOR STYLES FS123C209MXA, FS132C200MV, FS132C209MV, FS132C209MVA, FS132C210MV, FS133C200MW, FS133C209MV, FS133C209MVA (ALL GAUGES)

Ref. No.	Part No.	Description	Amt. Req.
1.	57845AA	Spreader, for Styles FS132C210MV, FS133C200MW	1
1A.	50345L	Spreader, for Styles FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA	1
2.	C50046	Spreader Holder, for Styles FS123C209MX, FS123C209MXA, FS133C200MW	1
2A.	34846B	Spreader Holder, for Styles FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA	1
2B.	57846A	Spreader Holder, for Styles FS132C200MV, FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA, FS132C210MV	1
3.	22562B	Screw	2
3A.	77	Screw, for Styles FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA	1
3B.	77A	Screw, for Styles FS132C200MV, FS132C209MVA, FS132C209MVA, FS133C209MV, FS133C209MVA, FS132C210MV	2
4.	77	Screw	2
4A.	G50-785	Screw, for Styles FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA	1
4B.	22547D	Screw, for Styles FS132C200MV, FS132C209MV, FS132C209MVA, FS132C210MV, FS133C209MV, FS133C209MVA	2
5.	41332J	Thrust Washer	2
6.	34847A	Spreader Holder Drive Shaft	1
7.	1204002	Oil Wick	1
8.	34848	Carrier Connecting Rod Assembly	1
9.	22729	Screw	2
10.	15430L	Felt, green	1
-	U94194U	Wick	1
11.	22729	Screw	2
12.	93	Screw	1
13.	57835M	Washer, ball	1
14.	20	Washer, for carrier connecting rod assembly	1
15.	18	Nut, for carrier connecting rod assembly	1
16.	57849A	Spreader Rocker Shaft Arm	1
17.	55235D	Locking Stud	1
18.	6042A	Washer	1
19.	55235E	Nut	1
20.	52951C	Washer, for spreader rocker shaft collar	1
21.	999-232	"O" Ring, for spreader rocker shaft	2
22.	52849	Spreader Rocker Shaft	1
23.	57847	Crankshaft Thrust Collar	2
24.	95	Screw	2

1. thru 47A. See following page.

Technical diagram of a mechanical assembly with numbered components and torque specifications in Chinese

P070-93

SPREADER & SPREADER DRIVE (CONT.)

FOR STYLES FS123C209MXA, FS132C200MV, FS132C209MV, FS132C209MVA, FS132C210MV, FS133C200MW, FS133C209MV, FS133C209MVA(ALL GAUGES)

Ref.

No. Part No.

Description

Amt.

Req.

1. thru 24. See preceding page.

25.	57894C	Washer	3
26.	57847	Crankshaft Thrust Collar (replaces 29, 30, 31 on non-spreader machines)	1
27.	95	Screw	1
28.	57849D	Spreader Rocker Shaft Collar, Inner	1
29.	55235E	Nut	1
30.	6042A	Washer	1
31.	55235D	Locking Stud	1
32.	22559G	Screw, for spreader connecting rod ball joint, upper	2
33.	29105BD	Spreader Connecting Rod Ball Joint, upper	1
34.	52952D	Segment Lever	1
35.	55235D	Locking Stud	1
36.	6042A	Washer	1
37.	55235E	Nut	1
38.	18	Nut, for spreader connecting rod ball joint	1
39.	HA20A	Washer	1
40.	52916	Connecting Rod	2
41.	29126CR	Spreader Drive Eccentric Assembly	1
42.	95	Screw	2
43.	52951-B	Retaining Washer	1
44.	660-246	Retaining Ring	1
45.	52951C	Spacer Washer	1
46.	52947A	Counterweight	1
46A.	51247	Counterweight, for Styles FS122C200MB, FS122C203MB, FS122C209MX, FS122C209MXA, FS122C210MB, FS122C253MB, FS123C209MX, FS123C209MXA	1
47.	22587H	Screw, for counterweight	2
47A.	22894J	Screw	2

5A TORQUE: 19-21 In. Ibs. 2.1-2.3 Nm TORQUE: 55 In. Ibs. (6.2 Nm)

P071-93

Technical diagram of a mechanical assembly with numbered components and directional arrows indicating assembly or movement.

LOOPER ROCKER & CONNECTING ROD PARTS (ALL GAUGES)

Ref. No.	Part No.	Description	Amt. Req.
1.	52825D	Holder, for front needle guard	1
2.	77	Screw	2
3.	33174B	Screw	2
4.	51244L	Thrust Washer, for looper rocker shaft	2
5.	57725B	Front Needle Guard, for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB, FS132C200MV, FS132C210MV, FS133C200MW	1
5A.	A10085	Front Needle Guard, for Styles FS122C209MX, FS122C209MXA, FS123C209MX, FS123C209MXA, FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA...	1
6.	57846B	Nut, for looper rocker assembly	1
7.	57744A	Looper Rocker Frame	1
8.	98	Set Screw	1
9.	719	Stop Screw	1
10.	51236J	Connecting Pin	1
11.	56344D	Looper Rocker Arm	1
12.	CO67E	Cork Plug, for looper rocker shaft	1
13.	57744	Looper Rocker Shaft	1
14.	WO-3	Wool Yarn, for looper rocker shaft	1
15.	55244G	Stud, for looper rocker shaft collar	1
16.	51244N	Looper Rocker Shaft Collar	1
17.	51216N	Washer, for shaft stud	1
18.	18	Nut, for shaft stud	1
19.	627	Looper Lever Stud	1
20.	20	Washer, for looper lever stud	1
21.	56342K	Looper Drive Lever	1
22.	22882C	Screw	1
23.	20	Washer	1
24.	29476LV	Looper Connecting Rod Ball Joint, right	1
25.	18	Nut	1
26.	39141	Looper Connecting Rod	1
27.	269	Nut, for connecting rod	1
28.	87U	Screw, for ball joint oiler	1
29.	56393J	Ball Joint Oller	1
30.	29192Z	Looper Rocker Assembly	1
31.	51745	Stud, for looper rocker cone	1
32.	57713	Looper Rocker	1
33.	15465F	Looper Rocker Cone	1
34.	88	Screw	2
35.	258	Lock Nut	1
36.	22829	Screw	1
37.	96	Spot Screw, for looper rocker frame	1
38.	22874	Lock Screw, for looper rocker frame	1
39.	18	Nut, for looper connecting rod ball joint, left	1
40.	52708B	Looper	1
41.	73	Screw, for looper	1
42.	29105BA	Looper Connecting Rod Ball Joint, left	1
43.	22729C	Screw, for ball joint	2
*44.	56341N	Looper Connecting Rod Jointed Section Assembly, right	1
*45.	56341P	Looper Connecting Rod	1
*46.	56341S	Lever	1
*47.	660-310	Retaining Ring	2
*48.	56341W	Pin	1
*49.	56341T	Pin	1
*50.	660-210	Retaining Ring	2
*51.	56341V	Spring	1
*52.	56341R	Housing	1
*53.	18	Nut, right hand thread	1
*54.	51240D	Looper Connecting Rod	1
*55.	269	Nut, left hand thread	1

* These parts are an extra send charge and replace reference numbers 24, 25, 26, 27.

Technical diagram of a mechanical assembly with numbered components and torque specifications in Chinese

P158-94

MAIN & DIFFERENTIAL FEED MECHANISMS
(ALL GAUGES)

Ref. No.	Part No.	Description	Amt. Req.
1.	57835R	Feed Rocker Arm	1
2.	55235D	Stud, locking	1
3.	6042A	Washer	1
4.	55235E	Nut	1
5.	22768A	Screw	1
6.	660-438	Retaining Ring	1
7.	41391	Washer	2
8.	75	Screw, for segment plate	2
9.	52834N	Nut, for differential feed regulating stud	1
10.	39236C	Regulating Stud Stop	1
11.	51225W	Washer, for regulating stud	1
12.	22516	Screw, for segment plate	1
13.	52836Y	Feed Rocker Segment Plate	1
14.	52836AA	Shim, for segment plate	1
15.	57835X	Feed Rocker Shaft	1
16.	61341J	Washer	1
17.	52836AB	Feed Rocker	1
18.	22894P	Screw, for feed rocker	2
19.	52834R	Shaft, for feed rocker, upper	1
20.	56335D	Collar, for feed rocker shaft	1
21.	98	Screw, for collar	2
22.	22595	Screw, for feed dog	2
-	22593A	Screw, for feed dog, for StylesFS123C209MX, FS123C209MXA, FS133C200MW, FS132C210MV	2
23.	----
24.	22653B10	Main Feed Dog (see pages 43, 45, 47)	1
25.	51235G	Screw, for feed dog holder	1
26.	52853B	Washer	1
		Feed Dog Holder, main, for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB, FS132C200MV, FS132C210MV, FS133C200MW	1
		Feed Dog Holder, main, for Styles FS122C209MX, FS122C209MXA, FS123C209MX, FS123C209MXA, FS132C209MV, FS133C209MV, FS133C209MVA	2
26A.	57853F
		Oil Wick Retainer, for Styles FS122C209MX, FS122C209MXA, FS123C209MX, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA	1
27.	22593
28.	57834J	Screw, for guide	2
		Oil Wick, for Styles FS122C209MX, FS122C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123 C209MXA	1
29.	CL-21
		Oil Wick, for Styles FS122C209MX, FS122C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS133C209MXA	1
30.	22635E24	Screw	1
31.	57837D	Guide Plate, for differential feed dog	1
32.	57853E	Guide Plate and Support, for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB, FS132C200MV, FS132C210MV, FS133C200MW	1
32A.	57853	Guide Plate, for Styles FS122C209MX, FS122C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXA, FS123C209MXMVA	1
33.	57825E	Rear Needle Guard for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB, FS132C200MV, FS132C210MV, FS133C200MW	1
		Rear Needle Guard for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB, FS132C200MV, FS132C210MV, FS133C200MW	1
*33A.	57825F	Rear Needle Guard for Styles FS122C209MV, FS132C209MXA, FS133C209MXA, FS133C209MXA, FS133C209MXA, FS133C209MXA, FS133C209MXA, FS133C209MXA, FS133C209MXA, FS133C209MXA, FS133C209MXA, FS133 C209MXA	1
*34.	94	Needle Guard, rear	1
		Screw, for needle guard	2

1. thru 77. See following page
   *These parts are an extra send and charge. Will fit all styles except FS122C209MX, FS122C209MXA, FS123C209MX, FS123C209MXA, FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA, all gauges.

TORQUE: 55 In. lbs. (6.2 Nm) 77 76 75 74 71 70 69 68 67 66 65 64 63 62 61 59 58 57 56 55 54 53 52 51 50 49 48 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33A 32A 26A

P158-94

MAIN & DIFFERENTIAL FEED MECHANISMS (CONT.)

Ref.

No. Part No.

Description

Amt.

Req.

1. thru 34. See preceding page

1. 91D Screw, for rear needle guard .... 1
2. 57834A Differential Feed Bar 1
3. CL-21 Oil Wick 1
4. Differential Feed Dog (see pages 43, 47) 1
5. 91 Screw, for differential feed dog 1
6. 52834P Main Feed Bar 1
7. 22560B Screw 1
8. 39237G Bushing, for differential feed bar 2
9. 22766 Screw 1
10. 77 Screw, for main feed bar 1
11. 39237 Guide, for differential feed bar 1
12. 22565C Screw 2
13. 907 Nut, for regulating stud 1
14. 51225W Washer, for regulating stud 3
15. 39236V Bushing, for differential feed drive link 1
16. 52835T Driving Link 1
17. CL-21 Oil Wick 1
18. 39236B Regulating Stud, for differential feed 1
19. 29476RJ072 Feed Lift Eccentric Assembly 1
20. 22894AA Screw 1
21. 29476RS062 Looper Avoid Eccentric Assembly 1
22. 22894AA Screw 1
23. 52923D Looper Thread Take-Up 1
24. 22580D Screw, for take-up 2
25. 51236J Link Pin 2
26. WO-3 Oil Wick 2
27. 57822A Main Shaft 1
28. 56322B Screw 1
29. 22891B Gasket 1
30. 22801 Screw, for main shaft 1
31. 56336D Insert, feed crank stud 1
32. 660-269B Quad Ring 1
33. 22543B Screw, for stitch regulating 1
34. 56336 Feed Crank Stud 1
35. 22798C Screw, for feed crank stud 1
36. 56322C Head Plate 1
37. 22525A Screw, for head plate 4
38. 56336K Feed Crank Link Assembly 1
39. 56336C Ferrule 1
40. 51236J Link Pin 1
41. WO-3 1/8" Oil Wick 1
42. 269 Nut, for feed crank stud 1
43. 21657E Washer, for feed crank stud .... 1

Technical diagram of a mechanical linkage system with numbered components and assembly details

LIFTER LEVER PARTS (ALL GAUGES)

Ref. No.	Part No.	Description	Amt. Req.
1.	----	Presser Foot (see pages 43, 45, 47)	1
2.	52888B	Collar, for presser bar stop, for all Styles except FS122C209MX, FS122C209MXA, FS123C209MX, FS123C209MXA	1
3.	22562	Screw, for collar	2
4.	51257K	Presser Bar, for StylesFS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB, FS123C200MV, FS132C210MV, FS133C200MW	1
-	51257Y	Presser Bar, for StylesFS122C209MX, FS122C209MXA, FS123C209MX, FS123C209MXA, FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA	1
5.	51257M	Presser Bar Guide	1
6.	22596F	Screw	1
7.	22892E	Screw, for presser bar guide	1
8.	34883	Lifter Lever Link	1
9.	99392A	Screw, for lever link	1
10.	57883	Spacer Bushing	1
11.	22557G	Screw	1
12.	56383D	Spring, for connecting rod	1
13.	34383BA	Lifter Lever	1
14.	57893B	Head Oil Tube Clamp	1
15.	51256C	Presser Bar Spring	1
16.	56356A	Regulator Spring, for presser spring	1
17.	56383AB	Connecting Rod	1
18.	39552C	Washer, for lifter lever	1
19.	660-207	"O" Ring, for lifter lever	1
20.	51283H	Lifter Lever	1
21.	53783N	Lifter Lever, right	1
22.	22537	Screw	1
23.	21657Y	Lifter Lever Connection, tension release	1
24.	402	Screw, for guide	1
25.	22596	Screw	1
26.	21657W	Lifter Lever Shaft	1
27.	660-283A	Retainer Washer	1

Technical diagram of a mechanical assembly with numbered components and exploded views

Technical diagram of mechanical components with numbered parts, likely a lathe or assembly assembly.

P205-94

THREAD TENSION

Ref.

No. Part No.

Description

Amt.

Req.

1. 29477NG

2. 56392L

3. B3112704000

4. B3101804000

- B3103804000

1. 56392H

2. B3120352000

3. B3126012000

4. B3120704000

5. 56392G

6. 57892K

7. NS6110420SP

8. 57865

9. 57892L

10. 21657AP

11. 56392M

12. 56392P

13. 56392L

14. 29477NH

15. 56392M

16. B3112704000

17. B3103804000

- B3101804000

1. 56392H

2. B3120352000

3. B3126012000

4. B3120704000

5. 56392G

6. 57892K

7. NS6110420SP

8. 57865

9. 57892L

10. 21657AP

11. 56392M

12. 56392P

13. 56392L

14. 29477NF

15. 56392M

16. B3112704000

17. B3103804000

- B3101804000

1. 56392H

2. B3120352000

3. B3126012000

4. B3120352000

5. 56392G

6. 57892K

7. NS6110420SP

8. 57865

9. 57892L

10. 21657AP

11. 56392M

12. 56392L

Thread Tension Assembly, 3 thread, for Styles FS122C200MB, FS122C203MB, FS122C209MXA, FS122C209MX, FS122C210MB, FS122C253MB, all gauges ...

Knob, for needle (red) 1

Ferrule, tension spring 3

Spring, for needle (red) 2

Spring, for looper (blue) 1

Shield, for spring 3

Tension Disc Felt 3

Tension Disc 6

Tension Disc Felt 3

Tension Post 3

Eyelet, for tension thread 3

Nut 3

Lead-In Thread Guide 3

Support, for tension post 1

Separator, for tension disc 1

Knob, for looper (blue) 1

Vibration Damper 1

Knob, for needle (red) 1

Thread Tension Assembly, 4 thread, for Styles FS132C200MV, FS132C209MV, FS132C209MVA, FS132C210MV, all gauges ....

Knob, for spreader (blue) 1

Ferrule, tension spring 4

Spring, for spreader (blue) 1

Spring, for needle (red) 2

Shield, spring 4

Tension Disc Felt 4

Tension Disc 8

Tension Disc Felt 4

Tension Post 4

Eyelet, for tension thread 4

Nut 4

Lead-In Thread Guide 4

Support, for Tension Post 4

Separator, for tension disc 1

Knob, for looper (blue) 1

Vibration Damper 1

Knob, for needle (red) 2

Thread Tension Assembly, 5 thread, for Styles FS123C209MX, FS123C209MXA, FS133C200MW, FS133C209MV, FS133C209MVA .060 gauge ....

Knob, for spreader (blue) 1

Ferrule, for tension spring 5

Spring, for spreader (blue) 2

Spring, for needle (red) 3

Shield, spring 5

Tension Disc Felt 5

Tension Disc 10

Tension Disc Felt 5

Tension Post 5

Eyelet, for tension thread 5

Nut 5

Lead-In Thread Guide 5

Support, for tension post 1

Separator, for tension disc 1

Knob, for looper (blue) 1

Knob, for needle (red) 3

Technical diagram of a mechanical assembly with numbered components and exploded views, labeled P230-94.

COVERS & MISCELLANEOUS PARTS (ALL GAUGES)

Ref. No.	Part No.	Description	Amt. Req.
1.	52882AL	End Cover	1
2.	660-1001	Rubber Grommet	4
3.	87A	Screw	1
4.	22773A	Screw	3
5.	60038K	Washer	3
6.	80	Screw, for cloth plate	2
7.	52801K	Cloth Plate, for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB, FS132C200MV, FS132C210MV, FS133C200MW	1
8.	22839C	Screw, for cloth plate	2
9.	52802H	Cloth Plate Slide Cover, for Styles FS122C209MX, FS123C209MX	1
9A.	52802G	Cloth Plate Slide Cover, for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS132C200MV, FS132C210MV, FS133C200MW	1
-	52802K	Cloth Plate Slide Cover, for Style FS122C253MB	1
10.	660-1004	Screw, for panel	1
11.	57882N	Pad, sound damping, for StylesFS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB	1
12.	22585A	Screw	3
13.	22524	Screw	8
14.	56382G	Oil Resistant Top Cover	1
15.	56382H	Gasket	1
16.	50382T	Front Cover Stop	1
17.	50393W	Rubber Bumper	1
18.	53634C	Washer	1
19.	22519J	Screw	1
20.	57894E	Oil Shield	1
21.	87	Screw, for throat plate	2
22.	----	Throat Plate (see pages 43, 47)	1
23.	22839	Screw, for throat plate support	2
24.	52880A	Throat Plate Support, for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB, FS132C200MV, FS132C210MV, FS133C200MW	1
-	660-1008	Rubber Grommet	2
25.	51280J	Pin	2
26.	57885	Hinge Bracket	1
27.	57885B	Hinge Bracket	1
28.	43281K	Spring, for hinge bracket	2
29.	90	Screw	4
30.	57885A	Spring Pin, all Styles except FS122C209MXA, FS123C209MXA	1
31.	22564	Screw	1

1. thru 51. See following page

Technical diagram of a mechanical assembly with numbered components and exploded views, labeled P230-94.

Simple line drawing of a mechanical part with a labeled dimension (94), no text or symbols present.

COVERS & MISCELLANEOUS PARTS (CONT.) (ALL GAUGES)

Ref.

No. Part No.

Description

Amt.

Req.

1. thru 31. See preceding page

32.	52864X	Insert, for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB, FS132C200MV, FS132C210MV, FS133C200MW	1
-	52864AA	Insert, for Styles FS122C209MX, FS122C209MXA, FS122C253MB, FS123C209MX, FS123C209MXA, FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA	1
-	52864AB	Insert, for Style FS122C253MB	1
33.	90	Screw	2
34.	50303A	Edge Guide	1
35.	22561	Screw	2
36.	25CC	Screw	2
37.	22852G	Screw	1
38.	23432B	Folder Clamp	1
39.	T38	Screw	2
40.	53634C	Washer	2
41.	57864B	Clamp Plate	1
42.	52864W	Folder Support Bracket	1
43.	57864A	Clamp Plate	1
44.	52882AJ	Swing Down Cover	1
45.	57885C	Hinge Bracket, left	1
46.	22848	Screw, for hinge	8
47.	57885D	Hinge Bracket, right	1
48.	52882AR	Swing Down Cover, for Style FS122C253MB	1
49.	23306BM	Mounting Bracket, for Style FS122C253MB	1
50.	22653B40	Screw, short, for Style FS122C253MB	1
51.	22653B48	Screw, long, for Style FS122C253MB	1

Technical diagram of a mechanical assembly with numbered components, likely an electrical or mechanical assembly.

FAST ACTION TAPE CUTTER, THROAT PLATE SUPPORT & COVERS FOR STYLES

FS122C209MX, FS122C209MXA, FS123C209MX, FS123C209MXA, FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA (ALL GAUGES)

Ref.

No. Part No.

Description

Amt.

Req.

1. 29933AAA Tape Cutter Assembly 1
2. 92899DA Connection Plate and Valve 1
3. 999-199A Rapid Action Hose Coupling .... 1
4. 999-205H Plug In Nipple 1
5. 999-182 Swivel Elbow 1
6. 999-140 Muffler 2
7. 999-149 Gasket 3
8. 999-93 Gasket 2
9. 95424A Screw 2
10. 95406B Screw 3
11. 99702E Eccentric Pin 1
12. 95169 Screw 1
13. 8372A Washer 5
14. 29933A Cutter Assembly 1
15. 57849F Knife Guard 1
16. 20 Washer 2
17. 95157 Screw 2
18. 22585C Screw 1
19. 95259A Nut 3
20. 95956 Washer 3
21. 99670MA Knife, upper 1
22. 99316B Screw 1
23. 99316C Screw 1
24. 99316D Screw 1
25. 52801L Cloth Plate 1
26. 99702D Knife Clamp, lower 3
27. 52802H Cloth Plate Slide 1
28. 99699M Knife, lower 1
29. 99316A Screw 3
30. 52880B Throat Plate Support 1
31. 660-1008 Rubber Grommet 2
32. 51280J Pin 2
33. 22839 Screw 3

Technical diagram of a mechanical assembly with numbered components and directional arrows indicating motion or assembly.

3A

3B

Technical diagram showing three views of a mechanical component with numbered parts and directional arrows indicating features.

18A

Technical diagram of an electrical contactor assembly with numbered components and wiring connections

Technical diagram of a mechanical assembly with numbered parts, likely an electrical or mechanical component.

P078-93

PRESSER FOOT, THROAT PLATE & FEED DOG PARTS

Ref.			Amt.
No.	Part No.	Description	Req.

1.	50320V16	Presser Foot, for Style FS133C200MW, .060 gauge	1
-	50320U8	Presser Foot, for Styles FS122C200MB, FS122C203MB,FS122C210MB, FS122C253MB, FS132C200MV, FS132C210MV, .032 gauge	1
-	50320U12	Presser Foot Assembly, for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB, FS132C200MV, FS132C210MV, .040, .044 gauge	1

2.

22799B

Screw, hinge

1

3.

50330BN16

Bottom, Presser Foot for Style FS133C200MW, .060 gauge ...... 1

3A.

50330BN8

Bottom, presser foot, for StylesFS122C200MB, FS122C203MB, FS122C210MB,

FS122C253MB, FS132C200MV, FS132C210MV,..032 gauge ........ 1

3B.

50330BN12

Bottom, presser foot, for StylesFS122C200MB, FS122C203MB, FS122C210MB,

FS122C253MB, FS132C200MV, FS132C210MV, .040, .044 gauge ...... 1

4.

605

Screw

1

5.

97109

Spring

1

6.

34730H

Presser Foot Shank

1

7.

51959E

Nut

1

8.

51430F

Nut

......

1

9.

22565E

Screw

1

10.

91

Screw

1

11.

187A

Screw

1

12.

52830G

Spring

......

1

13.

57WD

Screw

1

14.

G65-181

Plunger

1

15.

50330BP16

Yielding Section, for Style FS133C200MW, .060 gauge

1

-

50330BP8

Yielding Section, for Styles FS122C200MB, FS122C203MB, FS122C210MB,

FS122C253MB, FS132C200MV, FS132C210MV, .032 gauge .... 1

-

50330BP12

Yielding Section, for Styles FS122C200MB, FS122C203MB, FS122C210MB,

FS122C253MB, FS132C200MV, FS132C210MV, .040, .044 gauge ...... 1

16.

96651

Roll Pin

1

17.

96532

Roll Pin

1

18.

34724XX16

Throat Plate, for Style FS133C200MW, .060 gauge

1

18A.

34724XX8

Throat Plate. for Styles FS122C200MB. FS122C203MB. FS122C210MB. FS123C253MB.

FS132C200MV, FS132C210MV, .032 gauge

1

-

34724XX10

Throat Plate, for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB,

FS132C200MV, FS132C210MV, .040 gauge

1

-

34724XX12

Throat Plate, for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB,

FS132C200MV, FS132C210MV, .044 gauge

1

19.

57826F

Differential Feed Dog, for Style FS133C200MW, .060 gauge ....

1

-

57726A

Differential Feed Dog, for Styles FS122C200MB, FS122C203MB, FS122C210MB,

FS122C253MB, FS132C200MV, FS132C210MV, all gauges .... 1

20.

57705W

Main Feed Dog, for Styles FS122C200MB, FS122C203MB, FS122C210MB,

FS122C253MB, FS132C200MV, FS132C210MV, all gauges .... 1

1. thru 48. See following pages

Technical diagram of a mechanical assembly with numbered components and directional arrows indicating assembly or movement.

Technical line drawing of a mechanical bracket assembly with mounting holes and a labeled section (3A), no readable text or symbols present.

3B

18 19 20

18A

Technical diagram of an electrical contactor assembly with numbered components and wiring connections

Technical diagram of mechanical components with numbered parts, likely a valve or clamp assembly

P078-93

PRESSER FOOT, THROAT PLATE & FEED DOG PARTS (CONT.)

Ref.

No. Part No. Description

Amt.

Req.

1. thru 20. See preceding page

21.	57820B032	Presser Foot, for Styles FS122C209MX, FS122C209MXA, FS132C209MV, FS132C209MVA, .032 gauge	1
-	57820B044	Presser Foot, for Styles FS122C209MX, FS122C209MXA, FS132C209MV, FS132C209MVA, .040, .044 gauge	1
-	57820B060	Presser Foot, for Styles FS123C209MX, FS123C209MXA, FS133C209MV, FS133C209MVA, .060 gauge	1
22.	77B	Screw	2
23.	A10120L	Presser Foot Shank	1
24.	22798A	Screw	3
25.	A10120K	Cover	1
26.	99316	Screw	5
27.	57830T	Spring	2
28.	57830V	Spring	1
29.	57830E	Presser Foot Yield, left, for Styles FS122C209MX, FS122C209MXA, FS132C209MV, FS132C209MVA, .032 gauge	1
-	57830F	Presser Foot Yield, left, for Styles FS122C209MX, FS122C209MXA, FS132C209MV, FS132C209MVA, .040, .044 gauge	1
-	57830D	Presser Foot Yield, left, for Styles FS123C209MX, FS123C209MXA, FS133C209MV, FS133C209MVA, .060 gauge	1
30.	57830N	Guide	1
31.	57830M	Pin	1
32.	57830S	Presser Foot Bottom Yielding Section, hinged, for StylesFS122C209MX, FS122C209MXA, FS132C209MV, FS132C209MVA, .032 gauge	1
-	57830R	Presser Foot Bottom Yielding Section, hinged, for StylesFS122C209MX, FS122C209MXA, FS132C209MV, FS132C209MVA, .040, .044 gauge	1
-	57830P	Presser Foot Bottom Yielding Section, hinged, for StylesFS123C209MX, FS123C209MXA, FS133C209MV, FS133C209MVA, .060 gauge	1
33.	A10120M	Presser Foot Guide	1
34.	96508	Pin	1
35.	A10135A-8	Presser Foot Bottom, for Styles FS122C209MX, FS122C209MXA, FS132C209MV, FS132C209MVA, .032 gauge	1
-	A10135A12	Presser Foot Bottom, for Styles FS122C209MX, FS122C209MXA, FS132C209MV, FS132C209MVA, .040, .044 gauge	1
-	A10135A16	Presser Foot Bottom, for Styles FS123C209MX, FS123C209MXA, FS133C209MV, FS133C209MVA, .060 gauge	1
36.	A10077H	Yielding Section	1

1. thru 48. See following page

Technical diagram of a mechanical assembly with numbered components for identification

3A

3B

Technical diagram of a mechanical component with labeled parts 18, 19, and 20

18A

Technical diagram of an electrical contactor assembly with numbered components and wiring connections

Technical diagram of a mechanical assembly with numbered parts, likely an electrical or mechanical component.

P078-93

PRESSER FOOT, THROAT PLATE & FEED DOG PARTS (CONT.)

Ref.

No. Part No.

Description

Amt.

Req.

1. thru 36. See preceding pages

1. 87 Screw, for throat plate 2

2. 57824F032 Throat Plate, for Styles FS122C209MX, FS122C209MXA, FS132C209MV, FS132C209MVA, .032 gauge 1

- 57824F040 Throat Plate, for Styles FS122C209MX, FS122C209MXA, FS132C209MV, FS132C209MVA, .040 gauge .... 1

- 57824F044 Throat Plate, for Styles FS122C209MX, FS122C209MXA, FS132C209MV, FS132C209MVA, .044 gauge .... 1

- 57824F060 Throat Plate, for Styles FS123C209MX, FS123C209MXA, FS133C209MV, FS133C209MVA, .060 gauge .... 1

1. 90 Screw, for throat plate 1

2. A10082A Differential Feed Dog Holder, for Styles FS122C209MX, FS122C209MXA, FS123C209MX, FS123C209MXA, FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA, all gauges 1

3. A10082 Differential Feed Dog, for Styles FS122C209MX, FS122C209MXA, FS123C209MX, FS123C209MXA, FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA, all gauges 1

4. 51235G Washer 1

5. 22595 Screw, for differential feed dog 1

6. 57805A Main Feed Dog, for Style FS133C200MW, .060 gauge .... 1

- 57805B Main Feed Dog, for Styles FS123C209MX, FS123C209MXA, FS133C209MV, FS133C209MV, FS133C209MV, FS133C209MVA, all gauges .... 1

- 57805C Main Feed Dog, for Styles FS122C209MX, FS122C209MXA, FS133C209MVA, .044 gauge 1

- 57805D Main Feed Dog, for Styles FS122C209MX, FS122C209MXA, FS132C209MV, FS132C209MVA, .040 gauge .... 1

- 57805E Main Feed Dog, for Styles FS122C209MX, FS122C209MXA, FS132C209MV, FS132C209MVA, .032 gauge 1

1. 77 Screw 1

2. 87 Screw, for main feed dog 1

3. 57825H Rear Needle Guard, for Styles FS122C209MX, FS122C209MXA, FS123C209MX, FS123C209MXA, FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA, all gauges .... 1

4. 22585 Screw 1

Technical diagram of an electric motor assembly with numbered components and exploded view

P231-94 26 29 28 27 30 31 (a) Ununiquant

STEPPER MOTOR METERING DEVICE & SYNCHRONIZER KIT

FOR STYLE

FS122C253MB(ALL GAUGES)

Ref.

No. Part No.

Description

Amt.

Req.

1. 29986LS75 Stepper Motor Metering Device 1

2. 22653B36 Mounting Screw 2

3. 35086S Connector Bracket 1

4. 90241G Motor Wire Connection .... 1

5. 95167DV Screw M3 x 40 3

6. V90233WC Motor and Cable Assembly 1

7. 95166V Screw M3 X 8 4

8. 35086WD Mounting Plate 1

9. 22737 Screw 7

10. 95956 Washer 5

11. 99697FC Flat Spring 2

12. 34386AB1 Stand Off 1

13. 34386B Elastic Guide 2

14. 998-382 Knob 1

15. 25B Screw 2

16. 34386KC Cover 1

17. 34386KB Cover 1

- 999-106XA Bearing 1

- 99316 Screw 3

1. 77A Screw 2

2. 34386CB Roller Bracket 1

3. 34386GD Roller 1

4. 34386AC Knife Holder 1

5. 34386AB2 Stand Off 2

6. 34386EH Roller 1

7. 22743 Set Screw 2

8. 35086WD1 Bushing 1

9. 670N4 Control Box 1

10. AS12-13 Mounting Bracket 1

11. SC-330 Screw, for mounting bracket 4

12. SC-333A Screw, for mounting bracket 2

13. 670M10 Synchronizer 1

14. 670N5 Logic Box 1

P162-94 To Tape Cutter To Regulator

PNEUMATIC KNEE ACTUATOR & REGULATOR

FOR STYLES

MANUAL TAPE CUTTER ASSEMBLY

FOR STYLES FS122C203MB, FS122C253MB (ALL GAUGES)

Ref. No.	Part No.	Description	Amt. Req.
1.	29486A	Tape Cutter Assembly	1
2.	136	Cutter Mounting Screw	2
3.	21212	Collar	2
4.	52875F	Shaft	1
5.	93	Screw	2
6.	52875G	Spring	1
7.	52875E	Knife Holder, upper	1
8.	95	Screw	2
9.	52875A	Operating Lever	1
10.	95	Screw	1
11.	51283G	Spring	1
12.	6-99-80	Operating Wire	1
13.	52875D	Knife Upper	1
14.	22528	Screw, for upper knife	2
15.	22596	Screw, for lower knife	2
16.	22852	Screw	1
17.	12538	Nut	1
18.	52875B	Shaft	1
19.	15447A	Adjusting Screw	1
20.	22829	Screw	2
21.	604	Screw, for Cloth Guide	2
22.	52875C	Knife, lower	1
23.	52875J	Cloth Guide	1
24.	52875H	Knife Guard	1
25.	52875	Frame	1

P093-93

PNEUMATIC TAPE CUTTER ASSEMBLY FOR STYLES FS122C210MB, FS132C210MV (ALL GAUGES)

Ref.

No. Part No.

Description

Amt.

Req.

1. 29486R Tape Cutter Assembly 1
2. 136 Cutter Mounting Screw 2
3. 21212 Collar 2
4. 18 Nut 1
5. 52875T Blade Actuating Arm 1
6. 55244G Screw 1
7. 52875EA Holder 1
8. 93 Screw 2
9. 52875G Spring 1
10. 22894J Set Screw 1
11. 12538 Nut 1
12. 22894H Set Screw 1
13. NU-12 Nut 1
14. 22652A-16 Screw 1
15. 671A-2 Tape Cutter Air Cylinder 1
16. 671F-3 Male Elbow 1
17. 22852 Screw 1
18. 52875S Cylinder Mounting Bracket 1
19. 22604 Screw 1
20. 52875R Curved Upper Knife 1
21. 22528 Screw, for upper knife 2
22. 22596 Screw 2
23. 11698L Nut 1
24. 15447A Adjusting Screw 1
25. 22829 Screw 2
26. 604 Screw, for cloth guide 2
27. 52875C Lower Knife 1
28. 52875J Cloth Guide 1
29. 52875H Knife Guard 1
30. 52875 Frame 1
31. 52875U Shaft 1

P188-94

KNEE PRESS AND CONTROL BOX

FOR STYLES

FS122C209MX, FS132C209MV, (ALL GAUGES),

FS123C209MX, FS133C209MV, (.060 GAUGE)

Ref.			Amt.
No.	Part No.	Description	Req.

1. 90235DD Control Box 1

2. 90561V Wood Screws 4

3. 999-123C Plug 2

4. 998-348-0.315 Fuse 1

5. 90233AH Cable 1

6. 998-338A Knee Press 1

7. 998-147D Clamp 1

8. 90561Q Wood Screw 1

9. 998-147C Holder Rod 1

10. 998-387M Plug 1

THREAD STAND & MISCELLANEOUS ACCESSORIES (ALL GAUGES)

Ref.			Amt.
No.	Part No.	Description	Req.

1.	21101W4	Thread Stand, for Styles FS122C209MX, FS122C209MXA, FS123C209MX, FS123C209MXA, FS132C209MV, FS132C209MVA, FS133C209MV, FS133C209MVA..	1
-	21101W5	Thread Stand, for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB, FS132C200MV, FS132C210MV	1
-	21101W6	Thread Stand, for Styles FS133C200MW	1
2.	660-240	Thread Tweezer, for all Styles except FS133C200MW	1
3.	23279D	Threader, for all Styles except FS122C200MB, FS132C200MV, FS132C210MV, FS133C20MW	1
4.	660-264	"S" Hook	2
5.	421D34	Chain	1
6.	G21201	Screwdriver, for Style FS133C200MW	1
7.	TT17	Wrench, for Style FS133C200MW	1
8.	RM2871B	Cable Tie, for Style FS122C253MB	6
9.	660-870	Cable Tie Mount, for Style FS122C253MB	6
10.	51295A	Isolator	1
1.	51295B	Isolator	3
-	TT35	Looper Gauge, (sold separately, not shown)	1
-	660-457	Plastic Cover (not shown)	1
-	28604R	Oil Can (not shown)	1
-	28604W	Silicone Oil (not shown), for Styles FS122C200MB, FS122C203MB, FS122C210MB, FS122C253MB, FS132C200MV, FS132C210MV	1

Technical diagram of a mechanical device with numbered components, likely a valve or pump assembly.

P233-94

TAPE REEL ASSEMBLIES

Ref. No.	Part No.	Description	Amt. Req.
1.	29480AHU	Tape Reel Assembly....	1
2.	50322L	Support Shaft ....	1
3.	50392C	Tape Disc ....	1
4.	482C	Collar ....	1
-	22894C	Screw ....	2
5.	50322H	Shaft ....	1
6.	22728	Thumb Screw ....	1
7.	50364A	Holder ....	1
8.	90561K	Wood Screw ....	3

NOTES

NUMERICAL INDEX OF PARTS

Part No.	Page No.	Part No.	Page No.	Part No.	Page No.	Part No.	Page No.	Part No.	Page No.
11698L....55		22593....29	28604R....59	39583A....51	52802K....37	56322B....31
1204002....23		22593A....29	28604W....59	402....33	52804E....13	56322C....31
12538....53, 55		22595....29, 47	28C....21	41332J....23	52825D....27	56335D....29
12934A....19		22596....33, 53, 55	29105BA....27	41391....29	52830G....43	56336....31
136....53, 55		22596F....33	29105BB....19	421D34....59	52834N....29	56336C....31
15430L....23		22604....55	29105BC....19	482C....60	52834P....31	56336D....31
15447A....53, 55		22635E24....29	29105BD....25	50-216BLK....13	52834R....29	56336K....31
15465F....27		22642K-48....51	29126CR....25	50-895BLK....17	52835T....31	56341E....27
158B....13		22652A-16....55	29192Z....27	50303A....39	52836AA....29	56341F....27
18....23, 25, 27, 55		22652A12....21	29348AF....19	50320U12....43	52836AB....29	56341G....27
187A....43		22652J-14....51	29476LV....27	50320U8....43	52836Y....29	56341N....27
188D....17		22653B10....29	29476NZ....19	50320V16....43	52849....23	56341P....27
20....13, 17, 23, 27, 41		22653B36....49	29476RJ072....31	50322H....60	52853B....29	56341R....27
21101W4....59		22653B40....39	29476RS062....31	50322L....60	52864AA....39	56341S....27
21101W5....59		22653B48....39	29477NF....35	50330BN12....43	52864W....39	56341T....27
21101W6....59		22653L-8....19	29477NG....35	50330BN16....43	52875....53, 55	56341V....27
21104H....51		22728....60	29477NH....35	50330BN8....43	52875A....53	56341W....27
21212....53, 55		22729....23	29480AHU....60	50330BP12....43	52875B....53	56342K....21, 27
21375CE....13		22729AB....19	29480ARB....51	50330BP16....43	52875C....53, 55	56343C....19
21657AP....35		22729C....27	29486A....53	50330BP8....43	52875D....53	56343E....19
21657E....31		22737....49	29486R....55	50345L....23	52875E....53	56343F....19
21657W....33		22743....49	29933A....41	50364A....60	52875EA....55	56344D....27
21657X....17		22766....31	29933AAA....41	50373CQ....15	52875F....53	56350D....19
21657Y....33		22768....13, 19, 21	29986LS75....49	50382T....37	52875G....53, 55	56350G....19
21695R....15		22768A....29	33174B....27	50392C....60	52875H....53, 55	56350J....19
22516....13, 29		22773A....37	33795....15	50392D....17	52875J....53, 55	56350K....19
22519C....29		22798A....45	34317....21	50393W....37	52875L....51	56354D....19
22519J....37		22798C....31	34342J....21	51-561BLK....17	52875R....55	56356A....33
22524....13, 37		22799B....43	34383BA....33	51-902BLK....17	52875S....55	56382AA....13
22525A....31		22801....31	34386AB1....49	51154E....17	52875T....55	56382AB....13
22528....53, 55		22829....13, 27, 53, 55	34386AB2....49	51216M....19	52875U....55	56382AC....13
22537....33		22839....37, 41	34386AC....49	51216N....19, 27	52880A....37	56382AK....19
22539AA....15		22839C....13, 15, 37	34386B....49	51216P....19	52880B....41	56382AU....13
22539AB....15		22848....13, 37	34386CB....49	51225W....29, 31	52882AJ....39	56382AV....13
22539R....17		22851D....15	34386EH....49	51235G....29, 47	52882AL....37	56382AX....13
22539S....13		22852....53, 55	34386GD....49	51236J....27, 31	52882M....49	56382C....13
22541C....13, 15		22852G....39	34386KB....49	51240D....27	52883R....17	56382D....13
22542....15		22874....27	34386KC....49	51244L....27	52888B....33	56382G....37
22543B....31		22882C....27	34724XX10....43	51244N....27	52904B....13	56382H....37
22547D....23		22889H....13	34724XX12....43	51247....25	52904E....13	56382J....13
22548....13		22891B....31	34724XX16....43	51250D....19	52904G....13	56382K....13
22557G....33		22892E....33	34724XX8....43	51250V....19	52916....25	56382L....13
22559G....19, 25		22894....60	34730H....43	51254K....19	52923D....31	56382Y....13
22560B....31		22894AA....31	34758....15	51256C....33	52942AB....17	56383AB....33
22561....39		22894AB....19	34818B....21	51257AA....17	52942AF....21	56383D....33
22562....33		22894C....19, 60	34831C....15	51257K....33	52947A....25	56390....17
22562A....19		22894D....19	34844....15	51257M....33	52951-B....25	56390E....17
22562B....23		22894E....15	34846B....23	51257Y....33	52951C....21, 23, 25	56390G....17
22564....19, 37		22894H....55	34847A....23	51280J....37, 41	52952D....25	56390H....17, 21
22564B....15		22894J....25, 55	34848....23	51283G....53	52958D....13	56390J....17
22565C....31		22894P....29	34883....33	51283H....33	53634C....37, 39	56392G....35
22565E....43		22894Y....15	35086S....49	51295A....59	53758....13	56392H....35
22569B....17		23279D....59	35086WD....49	51295B....59	53783N....33	56392L....35
22569C....13		23306BM....39	35086WD1....49	51430F....43	54458-9....19	56392M....35
22574....19		23432B....39	35897BV....17	51745....27	55235D....25, 29	56392P....35
22580D....31		23439F....17	39141....27	51959E....43	55235E....25, 29	56393J....27
22585....47		23439G....17	39236B....31	52336A....19	55244G....27, 55	56393P....17
22585A....13, 15, 17, 37		258....27	39236C....29	52708B....27	56190....17	56393Q....17
22585C....15, 41		258A....17	39236V....31	52801K....37	56315A....19	56393W....17
22586R....19		25CC....39	39237....31	52801L....41	56316....19	56958A....21
22587H....25		269....27, 31	39237G....31	52802G....37	56316C....19	57705W....43
22587K....19		27-435BLK....21	39552C....33	52802H....37, 41	56321S....19	57713....27

NUMERICAL INDEX OF PARTS

Part No.	Page No.	Part No.	Page No.	Part No.	Page No.	Part No.	Page No.
57722B....31		57849G....49		660-264....59		96....27	RM2871B....59
57725B....27		57853....29		660-269B....31		96508....45	RM3293-2....51
57726A....43		57853E....29		660-283A....33		96532....43	SC-330....49, 51
57744....27		57853F....29		660-310....27		96651....43	SC-333A....49
57744A....27		57854....17		660-406....17		97109....43	T38....39
57757B....13		57858....13		660-434....51		98....27, 29	TT17....59
57770....15		57858A....15		660-438....29		98A....13	TT35....59
57782M....13		57864A....39		660-457....59		99316....45, 49	U94194U....23
57795B....13		57864B....39		660-617....15		99316A....41	V90233WC....49
57805A....47		57865....35		660-625....19		99316B....41	WO-3....19, 27, 31
57805B....47		57882J....13		660-665....17		99316C....41
57805C....47		57882K....15		660-739....17		99316D....41
57805D....47		57882L....15		660-870....59		99331A....21
57805E....47		57882M....49		661-258....17		99392A....33
57818A032....21		57882N....37		666-214....17		99670MA....41
57818A040....21		57882P....15		666-259....17		99682XCA....15
57818A044....21		57883....33		670M10....49		99697FC....49
57818A060....21		57885....37		670N4....49		99699M....41
57820B032....45		57885A....37		670N5....49		99702D....41
57820B044....45		57885B....37		671-D31....51		99702E....41
57820B060....45		57885C....39		671-F10....51		998-147C....57
57821D....19		57885D....39		671A-2....55		998-147D....57
57822A....31		57890B....17		671B13....51		998-338A....57
57824F032....47		57892C5....15		671F-3....51, 55		998-348-0.315....57
57824F040....47		57892H....15		69H....13		998-387M....57
57824F044....47		57892J....15		719....27		999-106XA....49
57824F060....47		57892K....35		73....27		999-123C....57
57825E....29		57892L....35		73A....13		999-140....41
57825F....29		57893....17, 19		75....29		999-149....41
57825H....47		57893A....17		77....15, 19, 23, 27, 31, 47		999-182....41
57826F....43		57893B....33		77A....23, 49		999-199A....41
57830D....45		57893C....17		77B....45		999-205H....41
57830E....45		57894....17		80....37		999-216K....17
57830F....45		57894C....25		80557....13		999-232....23
57830M....45		57894D....13		80665F....15		999-93....41
57830N....45		57894E....37		8372A....41		A10077H....45
57830P....45		57944B....15		87....37, 47		A10082....47
57830R....45		57WD....43		87A....37		A10082A....47
57830S....45		59493A....17, 19		87U....13, 27		A10085....27
57830T....45		6-67-125....17		88....27		A10120K....45
57830V....45		6-99-80....53		90....13, 17, 39, 47		A10120L....45
57834A....31		60038K....37		90233AH....57		A10120M....45
57834J....29		604....53, 55		90235DD....57		A10135A-8....45
57835M....23		6042A....25, 29		90241G....49		A10135A12....45
57835R....29		605....43		90561Q....57		A10135A16....45
57835X....29		605A....15		90561V....57		AS12-13....49
57836B....17		61321L....19		907....17, 31		B3101804000....35
57837D....29		61341J....29		91....31, 43		B3103804000....35
57842B....17		627....27		91D....31		B3112704000....35
57844....15		627A....17		92899DA....41		B3120352000....35
57844A....15		660-1001....37		93....23, 53, 55		B3120704000....35
57844C....13		660-1002....13		94....29		B3126012000....35
57845AA....23		660-1004....37		95....13, 23, 25, 53		C50046....23
57846A....23		660-1008....37, 41		95157....41		CL-21....17, 21, 29, 31
57846B....27		660-202....19, 21		95166V....49		CO67E....27
57847....23, 25		660-206....19		95167DV....49		G21201....59
57847B....17		660-207....33		95169....41		G50-785....23
57849....17		660-210....27		95259A....41		G65-181....43
57849A....23		660-215....19		95262V....21		HA20A....25
57849C....21		660-230....17		95406B....41		NS6110420SP....35
57849D....25		660-240....59		95424A....41		NU-11....51
57849F....41		660-246....25		95956....41, 49		NU-12....55

NOTES

NOTES

World map with latitude and longitude grid lines, showing continents and oceans (no text labels)

WORLDWIDE SALES AND SERVICE

Union Special Corporation maintains sales and service facilities throughout the world. These offices will aid you in the selection of the right sewing equipment for your particular operation. Union Special Corporation representatives and service technicians are factory trained and are able to serve your needs promptly and efficiently. Whatever your location, there is a qualified representative to serve you.

Corporate

Office:

One Union Special Plaza

Huntley, IL 60142

Phone: 847·669·5101

Fax: [phone]

European Distribution Center:

Union Special GmbH

Raiffeisenstrasse 3

D-71696 Möglingen, Germany

Tel: 49·07141·247·0

Fax: 49·7141·247·100

Brussels, Belgium

Charlotte, N.C.

El Paso, TX

Hong Kong, China

Huntley, IL

Leicester, England

Lille, France

Miami, FL

Milan, Italy

Möglingen, Germany

Montreal, Quebec

Osaka, Japan

Santa Fe Springs, CA

Other Representatives throughout all parts of the world.

Finest Quality

Union Special® INDUSTRIAL SEWING EQUIPMENT