MF61W - Vacuum Cleaner Marbella - Free user manual and instructions

USER MANUAL MF61W Marbella

Abstract geometric logo with a stylized 'M' inside a circle and diagonal line (no text or symbols)

MARBELLA

Colours and appearances may vary

User Manual

[Revision 6.0 October 2022]

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or SERIOUSLY INJURED if you do not follow instructions.

It is vital that you read and understand this user manual before using the product, including safety warnings, and any assembly and operating instructions. Keep the manual for future reference.

Safety precautions and recommendations detailed here must be fully understood and followed to reduce the risk of injury, fire, explosion, electrical hazard, and/or property damage.

Safety information presented here is generic in nature – some advice may not be applicable to every product. The term "equipment" refers to the product, be it electrical mains powered, battery powered or combustion engine powered.

• Before Use - If you are not familiar with the safe operation/handling of the equipment or are in any way unsure of any aspect of suitability or correct use for your application, you should complete training conducted by a person or organization qualified in safe use and operation of this equipment, including fuel/electrical handling and safety.
• Do NOT operate the equipment in flammable or explosive environments, such as in the presence of flammable liquids, gases or dust. The equipment may create sparks or heat that may ignite flammable substances.
• Keep clear of moving parts.
• Equipment may be a potential source of electric shock or injury if misused.
• Do NOT operate the equipment if it is damaged, malfunctioning or is in an excessively worn state.
• Do NOT allow others to use the equipment unless they have read this manual and are adequately trained.
• Keep packaging away from children - risk of suffocation! Operators must use the equipment correctly. When using the equipment, consider conditions and pay due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.
- Do not operate the equipment if bystanders, animals etc are within operating range of the equipment or the general work area.
- If devices are provided for connecting dust extraction / collection facilities, ensure these are connected and used properly. Dust collection can reduce dust-related hazards.

You CAN be KILLED or SERIOUSLY INJURED if you do not follow instructions.

General Personal Safety

• Wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect from eye and ear injury, poisoning, burns, cutting and crush injuries. Protective equipment such as safety goggles, respirators, non-slip safety footwear, hard hat, hearing protection etc should be used for appropriate equipment / conditions. Other people nearby should also wear appropriate personal protective equipment. Do not wear loose clothing or jewellery, which can be caught in moving parts. Keep hair and clothing away from the equipment.
• Stay alert and use common sense when operating the equipment. Do not overreach. Always maintain secure footing and balance.
• Do not use the equipment if tired or under the influence of drugs, alcohol or medication.
• This equipment is not intended for use by persons with reduced physical, sensory or mental capabilities.

General Fuel Safety

• Petrol/fuel/gasoline is extremely flammable – keep clear of naked flames or other ignition sources.
• Do not spill fuel. If you spill fuel, wipe it off the equipment immediately – if fuel gets on your clothing, change clothing.
• Do NOT smoke near fuel or when refuelling.
• Always shut off the engine before refuelling.
• Do NOT refuel a hot engine.
• Open the fuel cap carefully to allow any pressure build-up in the tank to release slowly.
  • Always refuel in well ventilated areas.
• Always check for fuel leakage. If fuel leakage is found, do not start or run the engine until all leaks are fixed.

General Carbon-Monoxide Safety

• Using a combustion engine indoors CAN KILL IN MINUTES. Engine exhaust contains carbon-monoxide – a poison you cannot smell or see.
• Use combustion engines OUTSIDE only, and far away from windows, doors and vents.

You CAN be INJURED if you do not follow instructions or equipment damage may occur.

General Equipment Use and Care

• The equipment is designed for domestic use only.
• Handle the equipment safely and carefully.
• Before use, inspect the equipment for misalignment or binding of moving parts, loose components, damage or any other condition that may affect its operation. If damaged, have the equipment repaired by an authorised service centre or technician before use.
• Prevent unintentional starting of the equipment - ensure equipment and power switches are in the OFF position before connecting or moving equipment. Do not carry equipment with hands or fingers touching any controls. Remove any tools or other items that are not a part of the equipment from it before starting or switching on.
• Do not force the equipment. Use the correct equipment for your application. Equipment will perform better and be safer when used within its design and usage parameters.
• Use the equipment and accessories etc. in accordance with these instructions, considering working conditions and the work to be performed. Using the equipment for operations different from those intended could result in hazardous situations.
• Always keep equipment components (engines, hoses, handles, controls, frames, housings, guards etc) and accessories (cutting tools, nozzles, bits etc) properly maintained. Keep the equipment clean and, where applicable, properly lubricated.
• Store the equipment out of reach of children or untrained persons. To avoid burns or fire hazards, let the equipment cool completely before transporting or storing. Never place or store the equipment near flammable materials, combustible gases or liquids etc.
• The equipment is not weather-proof, and should not be stored in direct sunlight, at high ambient temperatures or locations that are damp or humid.
• Do not clean equipment with solvents, flammable liquids or harsh abrasives.
• For specific equipment safety use and care, see Equipment Safety.

General Electrical Safety

• Inspect electrical equipment, extension cords, power bars, and electrical fittings for damage or wear before each use. Repair or replace damaged equipment immediately.
• Ensure all power sources conform to equipment voltage requirements and are disconnected before connecting or disconnecting equipment.
• When wiring electrically powered equipment, follow all electrical and safety codes.
• Wherever possible, use a residual current device (RCD).
• High voltage / high current power lines may be present. Use extreme caution to avoid contact or interference with power lines. Electrical shock can be fatal.

General Electrical Safety

• Electrically grounded equipment must have an approved cord and plug and be connected to a grounded electrical outlet.
• Do NOT bypass the ON/OFF switch and operate equipment by connecting and disconnecting the electrical cord.
• Do NOT use equipment that has exposed wiring, damaged switches, covers or guards.
• Do NOT use electrical equipment in wet conditions or in damp locations.
• Do NOT use electrical cords to lift, move or carry equipment.
• Do NOT coil or knot electrical cords, and ensure electrical cords are not trip hazards.

General Service Information

• The equipment must be serviced or repaired at authorised service centres by qualified personnel only.
• Replacement parts must be original equipment manufacturer (OEM) to ensure equipment safety is maintained.
• Do NOT attempt any maintenance or repair work not described in this manual.
• After use, the equipment and components may still be hot – allow the equipment to cool and disconnect spark plugs and/or electrical power sources and/or batteries from it before adjusting, changing accessories or performing repair or maintenance.
• Do NOT adjust while the equipment is running.
• Perform service-related activities in suitable conditions, such as a workshop.
• Replace worn, damaged or missing warning/safety labels immediately.

BEFORE YOU BEGIN

• Please read these instructions carefully to familiarize yourself with the required tools, materials, and installations instructions. Follow the sections that pertain to your particular installation. This will help you avoid costly mistakes. In addition to proper installation, please read all operating and safety instructions.
• Please provide adequate space for the bath unit in accordance with the rough-in. Arrange the location of drain in advance.
  • These instructions contain important care, cleaning, and warranty information.

COMPLIANCE INFORMATION

All installations must comply with council and local authority by-laws. It is the responsibility of the installer to ensure that the waste drain is made watertight by means of silicone sealant or caulking compound.

SAFETY

• Please do not have a steam bath and/or soaking bath immediately after drinking cold beverages and/or alcohol.
• Please do not have a steam bath and/or soaking bath immediately after playing sports.
• Please pay attention to the temperature difference between the inside and outside of the bathroom to ensure that the difference is no more than 10 degrees before bathing.
  • Water temperature should be between 26^ C ( 80^ F) and 32^ C ( 90^ F) when bathing to avoid potential health risks.
• Bathing time should be around 15 to 20 minutes at most, preferably no longer than that.
• When having a soaking bath, ensure that the water level is no higher than your chest.
• Drink adequate amounts of water to ensure you are not dehydrated after a steam bath and/or soaking bath.
• Immediately leave the bathtub if you feel any sort light-headedness or discomfort.
• Steam baths are not suitable for anyone with heart disease, high blood pressure, diabetes, or while pregnant.
• Please do not use any sorts of electronics when in or using the bathtub.

MAINTENANCE

• Most dirt will simply wash off with clean water.
• For spots and stains, we recommend using liquid dish washing soap or bleach. (Caution: Do not use any industrial strength cleaner of any sort to clean the bathtub surfaces).
• Use calcium remover to clean all chrome surfaces. (CAUTION: Avoid getting the calcium remover on the bathtub surface).

REPAIR

• For Minor Scratches & Dulling: Use liquid polisher such as Gel-Gloss or metal polish.
• For Deep Scratches or Burns: Use very fine sandpaper (1500 grit) in a circular motion covering a wider area greater than the scratch. Always wet the sandpaper with water. Repeat until the scratch is eliminated. Finally, polish the area with polishing compound to bring back its original shine. Use a soft cloth and a small amount of polish to buff the surface. Repeat as needed.

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material HazardFlammable liquids, gases or substances etc may present.Avoid ignition sources and open flames. Danger of fire.	Read User ManualRead and fully understand product safety warnings, operation, procedures etc before using the product.	Use Hand ProtectionWear appropriate hand protection and take due care as the product or use of the product may present hand hazards.	Exhaust FumesCarbon-Monoxide HazardDo not use the product in confined areas or without adequate ventilation. Carbon-monoxide poisoning can be fatal.
Electrocution / Electrical Shock HazardHigh voltage or high current electricity may be present or required by the product. Take due care when handling electrical products, cables, plugs and leads. Electrical shock can be fatal.	Toxic Fumes / Dust HazardUsing the product or by-products from use may produce fumes, smoke or particles that could be harmful if inhaled. Wear appropriate breathing protection and have adequate ventilation.	Explosive Material HazardCombustible liquids, gases or substances etc may be present.Avoid ignition sources and open flames. Danger of explosion.	Cutting / Amputation HazardThe product may have blades, edges or mechanical devices that can cause severe cut injury to fingers, limbs etc. Take due care when handling and using the product.
Crush HazardThe product may have blades, edges or mechanical devices that can cause severe crush injury to fingers, limbs etc. Take due care when handling and using the product.	Single Operator OnlyThe product must be operated by a single person only. More than one person operating the product may introduce additional hazards.	Use Face ProtectionWear appropriate full-face protection and take due care as the product or use of the product may present face and eye hazards.	Use Foot ProtectionWear appropriate foot protection and take due care as the product or use of the product may present foot hazards.
Use Eye / Ear / Head ProtectionWear appropriate eye and / or ear and / or head protection and take due care as the product or use of the product may present eye, hearing and head hazards.	Running HazardDo not run on or near the product as doing so may present a fall hazard.	Diving HazardDo not dive into the product as doing so may present a neck / head injury hazard.	Adult Supervision RequiredAlways supervise children and other users of a product to prevent drowning or injury.
Skin Penetration / Puncture HazardThe product may produce pressure, emit liquids or objects that can cause severe injury to fingers, limbs, blood etc. Take due care when handling and using the product.	Hot Surface HazardBe aware that the product may produce high temperatures and hot surfaces that can cause burn injuries.	Flying Debris HazardBe aware that the product or use of the product may present hazards produced by flying debris. Wear appropriate clothing and protective devices.	Moving Parts HazardBe aware that the product contains or uses mechanical devices that move or rotate. Always wait for moving parts to stop fully before handling the product, adjusting, maintenance etc.
Carbon-Monoxide HazardDo not use the product in confined areas or without adequate ventilation. Carbon-monoxide poisoning can be fatal.	Pull HazardBe aware that the product contains or uses mechanical devices that can pull in objects and can cause severe injury to fingers, limbs etc. Take due care when handling and using the product.	Slope / Fall Injury HazardBe aware that using the product on sloping surfaces or in slippery conditions may present additional dangers from falls and contact with blades, moving parts, hot surfaces etc.	"Slam Dunk" WarningDo NOT attempt "slam dunk" manoeuvres as this may result in severe injury due to falling, product breakage or collapse etc.
Electrocution / Electrical Shock Hazard - OutdoorHigh voltage or high current electricity may be present or required by the product. Do NOT use in rain, damp or wet conditions. Electrical shock can be fatal.	Electrocution / Electrical Shock Hazard - DisconnectHigh voltage or high current electricity may be present or required by the product. Always disconnect the product from the electrical supply before handling the product, adjusting, maintenance etc.	Power Line Electrocution HazardHigh voltage / high current power lines may be present. Use extreme caution to avoid contact or interference with power lines.Electrical shock can be fatal.	"Kick-Back" HazardHigh level of "kick-back" hazard that can cause the machine to suddenly rotate towards operator.Kick-back injury can be fatal.
Winch Operator Position HazardDo NOT stand between winch and load. Do NOT use winch to move people.	Winch Lift HazardDo NOT LIFT load vertically. Use machine to PULL only.	Cable HazardEnsure that load bearing cable is not kinked or knotted.	Winch Cable HazardEnsure that there is a minimum number of cable coils on winching mechanism.
Winch Hook HazardCarry hook to load – do NOT throw or run.	Flash / Blinding HazardWear appropriate eye protection for welding. Direct exposure to weld arcs may cause permanent eye injury.	Laser HazardLaser may be in use – do NOT look directly at laser or allow others to.

Table of Contents

Safety 2

Safety Symbols....4

Installation....7

Installation Requirements....7

Clearance Requirements....7

Site Requirements....7

Installation Steps ......7

Specifications 9

MF51W 9

MF71W 10

MF72B 11

MB61W....12

MF61W 13

MF62B 14

MFM61....15

MFM62....16

MBF63W....17

MF73W 18

MF74B 19

MF75W 20

MF64W 21

MF65W 22

Spare Parts....23

Installation

Installation Requirements

Leveler

Adjustable Wrench

Silicone Sealant/Caulking

Read the entire user manual before beginning the installation. If installing a rim-mount faucet, make sure there is no interference with the overflow drain before drilling any holes.

Position a protective covering or similar material in the bottom of the unit to protect the bathtub's surface from being scratched.

Clearance Requirements

Measure the area you intend to install the bathtub to ensure you have adequate space available for the installation.

Site Requirements

Subfloor Requirements

Check the flooring where the bathtub is going to be installed and make repairs as needed. Make sure the subfloor is level. It is strongly recommended to prepare a waterproof layer for the subfloor beforehand.

Installation Steps

This installation is meant for a certified plumber to install the bathtub and the plumbing needed for this bathtub.

1. Remove the Freestanding Bathtub from its wooden crate. To ensure that the Freestanding Bathtub does not come in contact with rough surfaces and get scratched, please remember to always protect it and place it on cloth/carpets.
2. Place the Freestanding Bathtub in the position you plan to install it.
3. Adjust the self-levelling feet until the Freestanding Bathtub is levelled. Ensure that the adjustable feet on the bathtub is aligned with the floor.

NOTE: The Freestanding Bathtub will only drain properly if it is levelled.

Diagram illustrating the step-by-step installation of a mechanical component, showing tool insertion and assembly with a magnified view.

1. Connect the Freestanding Bathtub to the waste outlet (Use plumber's putty, if applicable).
2. Test the drainage to ensure that the water drains properly. Fill the Freestanding Bathtub with water and check that ALL the water flows freely to the waste outlet (a small amount of water may pool due to surface tension).

NOTE: Please make sure that all the masking plastic adhered to your drain has been removed.

1. Apply a thick bead of silicone/caulking to the outline of the bathtub and allow it to set for 24 hours.

Test if drain works properly

NOTE: This installation is meant for a certified plumber to install the bathtub and the plumbing needed for this bathtub.

Specifications

MF51W

White 3D-rendered container with marbell branding, no visible text or symbols on the body

Series Accento

Colour White

Finish Gloss

Type Japanese soaking style

Installation Freestanding

Materials

Acrylic, Stainless Steel, Resin, Fiberglass

Plug Size 70mm

Drainage Hole Size 50mm

Waste Position Centre

Overflow No

Water Capacity 350L

Dimensions

-1 30 460 30 580 1370

30 460 6.30 30

Ø70 Ø50 510 750 1010 1500

MF71W

White ceramic bowl with marbelLA branding, no visible text or symbols on the body

Series Provence

Colour White

Finish Gloss

Installation Freestanding

Materials

Acrylic, Stainless Steel, Resin, Fiberglass

Plug Size 70mm

Drainage Hole Size 50mm

Waste Position Centre

Overflow No

Water Capacity 350L

Dimensions

-1 30 460 1200 590 -1 30 MARBELLAR MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLAR MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELLA MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL AR MARBELL

30 460 530 30

70 50 1110 1700 500 690

MF72B

Black glass bowl with white rim, no visible text or symbols

Series Provence

Colour Black

Finish Gloss

Type Oval

Installation Freestanding

Materials

Acrylic, Stainless Steel, Resin, Fiberglass

Plug Size 70mm

Drainage Hole Size 50mm

Waste Position Centre

Overflow No

Water Capacity 350L

Dimensions

30 460 590 1200 30

30 460 530 30 MARELA MARELA

Ø70 Ø50 1110 1700 500 690

MB61W

3D rendered white object with marbell-shaped side and curved top surface, no visible text or symbols

Colour White

Finish Gloss

Type Back to Wall

Installation Freestanding

Materials

Acrylic, Stainless Steel, Resin, Fiberglass

Plug Size 70mm

Drainage Hole Size 50mm

Waste Position Centre

Overflow No

Water Capacity 350L

Dimensions

700 470 570

1600 1054 30 Ø70 Ø50 487 350 700 30

MF61W

White ceramic bowl with embossed 'MARBELLA' text on its side (no other signage or symbols visible)

Series Aristo

Colour White

Finish Gloss

Installation Freestanding

Materials

Acrylic, Stainless Steel, Resin, Fiberglass

Plug Size 70mm

Drainage Hole Size 50mm

Waste Position Off Centre

Overflow No

Water Capacity 350L

Dimensions

30 30 560

10.30 670 480 390 270 600 1600

MF62B

Abstract black curved shape with white border, no text or symbols visible

Series Aristo

Colour Black

Finish Gloss

Installation Freestanding

Materials

Acrylic, Stainless Steel, Resin, Fiberglass

Plug Size 70mm

Drainage Hole Size 50mm

Waste Position Off Centre

Overflow No

Water Capacity 350L

Dimensions

30 30 560

10.30 6.70 4.80 3.90 2.70 9.50 6.00 1600 270

MFM61

3D rendered white object with marbell-shaped cutout pattern, no visible text or symbols

Series Chic

Colour White

Finish Matte

Type Back to Wall

Installation Freestanding

Materials

Acrylic, Stainless Steel, Resin, Fiberglass

Plug Size 70mm

Drainage Hole Size 50mm

Waste Position Centre

Overflow No

Water Capacity 350L

Dimensions

700 470 570

1600 1054 30 Ø70 Ø50 487 350 30 700 30

MFM62

3D rendering of a white oval-shaped container with marbell branding, placed on a patterned background (no text or symbols on the container itself)

Colour White

Finish Matte

Type Oval

Installation Freestanding

Materials

Acrylic, Stainless Steel, Resin, Fiberglass

Plug Size 70mm

Drainage Hole Size 50mm

Waste Position Centre

Overflow No

Weight 45kg

Water Capacity 350L

Dimensions

15 800 -1 15 470 640

1600 1100 800 580 Ø70 Ø50 15

MBF63W

3D rendered image of a white plastic bowl with marbell branding, no visible text or symbols on the body.

Colour White

Finish Gloss

Frame Stainless Steel

Installation Back to wall

Materials

Acrylic, Stainless Steel, Resin, Fiberglass

Plug Size 40mm

Plug Style

Pop-up (Watermark approved)

Waste Position Centre

Overflow Yes

Edge Width 25mm

Edge Style Flat

Dimensions

25 470 1040 590 1600 1040 850 80 780 675 510 418

80 470 510 25 590

MF73W

3D rendered image of a white bowl with marbellia branding on its side (no text or symbols on the bowl itself)

Colour White

Finish Gloss

Frame Stainless Steel

Installation Freestanding

Materials Acrylic, Stainless Steel

Plug Size 70mm

Plug Style Pop-up (Watermark approved)

Waste Position Centre

Overflow No

Edge Width 25mm

Edge Style Flat

Dimensions

470 590 1013

550

1680 1120 25 510 25 750

MF74B

Black ceramic bowl with smooth curved surface (no text or symbols visible)

Colour Black

Finish Gloss

Frame Stainless Steel

Installation Freestanding

Materials Acrylic, Stainless Steel

Plug Size 70mm

Plug Style Pop-up (Watermark approved)

Waste Position Centre

Overflow No

Edge Width 25mm

Edge Style Flat

Dimensions

470 590 1013

550

1680 1120 25 510 750 25

MF75W

3D rendered bowl with marbell branding, no visible text or symbols on the object itself

Colour White

Finish Gloss

Frame Stainless Steel

Installation Freestanding

Materials Acrylic, Stainless Steel

Plug Size 40mm

Plug Style Pop-up (Watermark approved)

Waste Position Centre

Overflow No

Edge Width 25mm

Edge Style Flat

Dimensions

1680 31 R1823 585 470 R1280 730 1000

R1757 R1500 520 520

1680 1080 20 520 25 760

MF64W

3D rendering of a rectangular box with marbell branding, no text or symbols visible on the body

Colour White

Finish Gloss

Frame Stainless Steel

Installation Freestanding

Materials Acrylic, Stainless Steel

Plug Size 40mm

Plug Style Pop-up (Watermark approved)

Waste Position Centre

Overflow No

Edge Width 40mm / 50mm / 100mm

Edge Style Flat

Dimensions

R80 450 580

750 500

100 R100 R125 405 50 1100 40 1600

MF65W

Exterior view of a modern office building (no signage)

Colour White

Finish Gloss

Frame Stainless Steel

Installation Freestanding

Materials Acrylic, Stainless Steel

Plug Size 40mm

Plug Style Pop-up (Watermark approved)

Waste Position Centre

Overflow No

Edge Width 15mm

Edge Style Flat

Dimensions

R6000 R125 500 1700 633 15

15 R6000 480 737

1750 1212 800 R165 R230

Spare Parts

Spare parts available for purchase, scan QR codes below:

QR Code
SKU

QR code image containing encoded data, no visible human-readable text

BTRBTMARAB61

QR Code
SKU

QR code image containing encoded data, no visible human-readable text

Close-up of a white, smooth, curved object with no visible text or symbols

BTRBTBMARAF61

QR code image containing encoded data, no visible human-readable text

White ceramic bowl with embossed 'MART' text on its side (no other visible text or symbols)

BTRBTBMARAM62

QR code image containing encoded data, no visible human-readable text

BTRBTBMARAF74

QR code image containing encoded data, no visible human-readable text

White oval-shaped container with embossed 'MARSH' text on the side (no other signage or symbols visible)

BTRBTMARAF63

QR code image containing encoded data, no visible human-readable text

Abstract black curved shape with white top and bottom edges (no text or symbols)

BTRBTMARAF62

QR Code

SKU

QR Code

SKU

QR code image containing encoded data, no visible human-readable text

BTRBTBMARAF75

QR code image containing encoded data, no visible human-readable text

White oval-shaped container with metallic rim, no visible text or symbols

BTRBTBMARAF73

Some experts believe that the incorrect or prolonged use of almost any product may cause serious injury or death. To help reduce your risk of serious injury or death, refer to the information below. For more information, see www.datastreamserver.com/safety

• Consult all documentation, packaging and product labelling before use. Note that some products feature documentation available online. It is recommended to print and retain the documentation.
  ■ Before each use, check the product for loose/broken/damaged/missing parts, wear or leaks (if applicable). Never use a product with loose/broken/damaged/missing parts, wear or leaks.
  ■ Products must be inspected and serviced (if applicable) by a qualified technician every 6 months. This is based on average residential use by persons of average size and strength, and on a property of average metropolitan size. Use beyond these recommendations may require more frequent inspections/servicing.
  ■ Ensure that all users of the product have completed a suitable industry recognised training course before being allowed access to the product.

The product has been supplied by a general merchandise retailer that may not be familiar with your specific application or description of application. Be sure to attain third-party approval from a qualified specialist for your application before use, regardless of any assurances from the retailer or its representatives.
This product is not intended for use where fail-safe operation is required. As with any product (for example, automobile, computer, toaster), there is the possibility of technical issues that may require the repair or replacement of parts, or the product itself. If the possibility of such failure and the associated time it may take to rectify could in any way inconvenience the user, business or employee, or financially affect the user, business or employee, then the product is not suitable for your requirements. This product is not intended for use where incorrect operation or a failure of any kind, including but not limited to, a condition requiring product return, replacement, parts replacement or service by a technician may cause financial loss, loss of employee time or an inconvenience requiring compensation.
If this product has been purchased in error when considering the information presented here, contact the retailer directly for details of their returns policy, if required.

my

topia.com.au