LAC5910INP - Hi-Fi System LG - Free user manual and instructions

Product Type	Hi-Fi System
Model	LAC5910INP
Brand	LG
Color	Black
Power Output	200 W RMS
Speaker Configuration	2.0 Stereo
Supported Media	CD, CD-R/RW, MP3, USB
Radio Tuner	FM/AM
Bluetooth	Yes (version 4.2)
USB Port	Yes (front)
Audio Input	3.5 mm AUX
Headphone Jack	Yes (3.5 mm)
Display	LED
Remote Control	Included
Dimensions (Main Unit)	Approx. 300 x 250 x 150 mm
Weight (Main Unit)	Approx. 2.5 kg
Power Supply	AC 120-240V, 50/60 Hz
Power Consumption	30 W (standby: <0.5 W)
Cleaning	Wipe with dry cloth; avoid solvents
Safety	Keep away from moisture; do not disassemble
Repairability	Professional service required; contact LG support

Frequently Asked Questions - LAC5910INP LG

How do I pair my smartphone via Bluetooth?

Press the Bluetooth button on the system or remote control. The display will show 'BT Ready'. On your phone, search for available devices and select 'LG LAC5910INP'. If prompted, enter PIN 0000. Once connected, you can stream audio.

Why is there no sound coming from the speakers?

First, check that the system is not muted (Mute button) and the volume is turned up. Ensure the correct input source is selected (e.g., CD, Bluetooth, AUX). Also verify that speaker wires are securely connected. If using an external device, check its volume.

How do I play a CD?

Press the CD button to select CD mode. Gently insert a CD with the label side up into the slot. The player will automatically start playback. Use controls like Play/Pause, Stop, Skip to navigate tracks.

How do I set and store radio stations?

Press the FM/AM button to select the band. Use the Tuning buttons to find a station. Press and hold one of the Preset numbers (1-10) for a few seconds to store it. Repeat for other stations. To recall, press the preset number directly.

Can I play music from a USB drive?

Yes, insert a USB stick with MP3 files into the front USB port. The system will switch to USB mode automatically. Use the Play/Pause and Skip buttons to control playback. Note that the USB must be formatted as FAT32.

The remote control is not working. What should I do?

Replace the batteries with new CR2025 coin cells. Make sure there are no obstacles between the remote and the system's sensor. Point the remote directly at the front panel. If still not working, try resetting the system by unplugging it for a minute.

How should I clean the system?

Disconnect the power before cleaning. Use a soft, dry cloth to wipe the exterior. Avoid using any chemical solvents, abrasives, or water directly on the unit. For stubborn dirt, slightly dampen the cloth with water and wring it out well.

What is the power consumption in standby mode?

The standby power consumption is less than 0.5 W. To completely cut off power, unplug the system from the wall outlet.

What should I do if an error code appears on the display?

Common error codes: NO DISC (no CD inserted), ERROR (try cleaning CD lens or restart). PROTECT output overload; reduce volume or check speaker connections. If the error persists, contact LG customer support.

Is there a warranty for this product?

Yes, LG offers a standard 1-year limited warranty for manufacturing defects. Keep your purchase receipt as proof. For warranty claims, contact LG service center. Extended warranty options may be available at purchase.

USER MANUAL LAC5910INP LG

LAC5910IN/LAC6910IN_LAC5910INP/LAC6910INP.LGEIQ_CL_ENG_MFL61778403

LG

Life's Good

LAC5910IN / LAC6910IN

LAC5910INP / LAC6910INP

ENGLISH

Made for iPod

"Made for iPod" means that an electronic accessory has been designed to connect specifically to

iPod and has been certified by the developer to meet Apple performance standards.

Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

iPod is a trademark of Apple Inc., registered in the U.S. and other countries.

Table of Contents

3 Safety Note

4 [LAC5910IN/LAC5910INP] Front Panel / Remote Control

5 [LAC6910IN/LAC6910INP] Front Panel / Remote Control

6 [LAC5910IN/LAC5910INP] About Detachable Control Panel

7 [LAC6910IN/LAC6910INP] About Detachable Control Panel

8 Installation

Basic installation

Removing the existing receiver unit

ISO-DIN installation

Battery installation

9 Connection

10 Basic operation

Mute

Using the EQ

Adjusting the sound level

XDSS+(Extreme Dynamic Sound System)

Checking the clock

Setting the clock

11 Listening to a CD

Pause or restart a CD

Search for a section within a track / file

Skip to another track / file

Intro scan

Repeat

Shuffle

MP3/WMA Track -10 / +10

MP3/WMA Folder UP/DOWN

Checking information about your music

12 Listening to the radio

Auto search memory

Storing and recalling broadcast frequencies

To scan the preset stations

To tune in the preset stations

Connecting USB device

13 Listening to music by using iPod

Pause or restart playback

Shuffle

Repeat

Checking music menus

Checking information about your music

Changing iPod settings

14 Connecting an Auxiliary Equipment

Changing settings

15 Troubleshooting

16 Specifications

Compatible iPod models

Safety Note

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT SPLIT COVER(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

Always operate the vehicle in a safe manner.

Do not become distracted by the vehicle while driving, and always be fully aware of all driving condition. Do not change settings, or any functions. Pull over in a safe and legal manner before attempting such operations.

Do not use for many hours at extremely low or high temperature. (-10\~60°C)

To reduce the risk of electric shock, do not remove the cover or back of this product. There are no user-serviceable parts inside. Refer servicing to qualified service personnel.

To reduce the risk of fire or electric shock, do not expose this product to dripping or splashing water, rain, or moisture.

The temperature of unit's outside can be extremely high, please use the unit after proper installation in your vehicle.

This unit cannot play 8cm disc (use 12cm disc only).

CAUTION: This product uses a Laser System.

To ensure proper use of this product, please read this owner's manual carefully and retain it for future reference.

Should the unit require maintenance, contact an authorized service center. Performing controls, adjustments, or carrying out procedures other than those specified herein may result in hazardous radiation exposure.

To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

Caution

When being connected in a wrong way, the unit displays as follows.
- Antenna port short : "ANTENNA ON PORT SHORT CIRCUIT CHECK"

After connecting it again, restart the unit.

You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs.

When setting the option to Live File System, you cannot use it on LG players. (Mastered/Live File System : Disc format system for Windows Vista)

[LAC5910IN/LAC5910INP] Front Panel / Remote Control

1 2 3 4 5 6 7 8 9 10 11 12 13 14 TENDER AS HDL BAND VOL.MOTE XOSS+ DSP 1 sp 2 sp 3 sp 4 sp 5 AUX 22 21 20 19 18 17 16 15

POWER MENU VOLUME 10 2 3 SRC NUMBER 4 INT BPT 5 1 2 3 6 7 8 9 10 11 12 13 14 15 16 SHP SHELV BAND DEV ENT 0 iPad MENU DISP

1 SOURCE [SRC]

2 • Auto Store [ ∧/AS]

- Preset Scan [v/PS]

- MP3/WMA Track +10/-10 ∧/V

- Folder Up/Down √v

3 [ENTER]

Skip / Search / Seek / Tune -◀ /

▶|+

4 • Volume

• [MUTE]

• Power [PWR]

5 Equalizer [EQ]

6 Select [SEL]

7 Remote Sensor(Optional)

8 CD slot

9 Display window

10 Extreme Dynamic Sound System

[XDSS+]

11 Display [DISP]

12 Eject ▲

13 Release

14 USB slot

15 AUX in

16 Preset Station [1\~6]

17 Shuffle [SHF]

18 Repeat [RPT]

19 Intro Scan [INT]

20 Play/Pause ▶/II

21 • [BAND]

• [DRIVE]

- iPod MENU

22 • [MENU]

1 Power [POWER] / Mute

2 Select [MENU/SEL]

3 Source [SRC]

4 Play / Pause ▶/■

5 Intro Scan [INT]

6 Shuffle [SHF]

7 • MP3/WMA Track +10

- Folder Up

• Auto Store

8 • CD Skip / Search

- Seek / Tune

9 • [ BAND]

- DRIVE [DRV]

- iPod MENU

10 Volume Up / Down

11 Number [#]

12 Repeat [RPT]

13 Number [0 -9]

14 • CD Skip / Search

16 • MP3/WMA Track -10

- Folder Down v

- Preset Scan

[LAC6910IN/LAC6910INP] Front Panel / Remote Control

1 2 3 4 5 6 7 8 9 10 11 12 A2 PS PAN VOLUME SNC KISS+ DEP BND PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM PWM 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12 13

POWER MENU VOLUME 10 2 3 SBC NUMBER 4 INT BP2 1 2 3 5 6 7 8 9 10 11 12 13 14 15 16 SHP RANG-DSY 0 DSP iPod MENU

1 • Auto Store [ ^/AS]

• Preset Scan [V/PS]
  • MP3/WMA Track +10/-10 A/V
• Folder Up/Down AW

2 [ENTER]

Skip / Search / Seek / Tune -I◀ / ▶I+

3 • Volume

• [MUTE]

• Power [PWR]

4 Equalizer [EQ]
5 Select [SEL]
6 SOURCE [SRC]
7 Remote Sensor(Optional)
8 Display window

9 Extreme Dynamic Sound System
[XDSS+]
10 Display [DISP]
11 Release
12 USB slot
13 AUX in
14 Preset Station [1\~6]
15 Shuffle [SHF]
16 Repeat [RPT]
17 Intro Scan [INT]
18 Play/Pause ▶/II
19 • [BAND]
• [DRIVE]
- iPod MENU
20 • [MENU]

1 Power [POWER] / Mute
2 Select [MENU/SEL]
3 Source [SRC]
4 Play / Pause ▶/II
5 Intro Scan [INT]
6 Shuffle [SHF]
7 • MP3/WMA Track +10
- Folder Up
• Auto Store
8 • CD Skip / Search
- Seek / Tune

9 • [ BAND]
- DRIVE [DRV]
- iPod MENU
10 Volume Up /Down
11 Number [#]
12 Repeat [RPT]
13 Number [0 -9]
14 • CD Skip / Search
- Seek / Tune ▶▶ ▶▶ I
• [ENTER]
15 Display [DISP.]
16 • MP3/WMA Track -10
- Folder Down V
- Preset Scan

[LAC5910IN/LAC5910INP] About Detachable Control Panel

Attaching the control panel

1 Align the left side of the panel with the stopper.
2 Push the right side or panel into the unit until it clicks.

Detaching the control panel

1 Press the " " (RELEASE) to open the control panel.
2 Hold the right part of the control panel.
3 Pull out the control panel.
4 Place the control panel in the supplied protective case.

Caution

• The control buttons may not work properly if the control panel is not attached properly. If this occurs, gently press the display.
• Do not leave the control panel in any area exposed to high temperatures or direct sunlight.
• Do not drop the control panel or otherwise subject it to strong impact.
• Do not allow such volatile agents as benzine, thinner, or insecticides to come into contact with the surface of the control panel.

Control panel Protective Case

Note

Periodically wipe the contacts on the back of the control panel with a cotton swap moistened with alcohol. For safety, turn off the ignition before cleaning, and remove the key from the ignition switch.

[LAC6910IN/LAC6910INP] About Detachable Control Panel

Attaching the control panel

1 Attach part A of the control panel to part B of the unit.

2 Attach part C of the control panel to part D of the unit while pushing the control panel to left.

3 Close the control panel.

Caution

• When detaching or attaching the control panel, do not press the display or control buttons.
• The control buttons may not work properly if the control panel is not attached properly. If this occurs, gently press the control panel.
• Do not leave the control panel in any area exposed to high temperatures or direct sunlight.
• Do not drop the control panel or otherwise subject it to strong impact.
• Do not allow such volatile agents as benzine, thinner, or insecticides to come into contact with the surface of the control panel.
• Do not try to disassemble the control panel.

Detaching the control panel

1 Press the " " button to unlock the control panel.
2 Push the control panel to left.
3 Pull the control panel out of the unit.
4 Put the detached control panel into the protective case.

Control panel Protective Case

Note

Periodically wipe the contacts on the back of the control panel with a cotton swap moistened with alcohol. For safety, turn off the ignition before cleaning, and remove the key from the ignition switch.

Installation

Basic Installation

Send the claws according to the thickness of the dashboard Control panel

Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting.

1 Remove the existing receiver unit.
2 Make the necessary connections.
3 Install the installation sleeve.
4 Install the unit into the installation sleeve.

ISO-DIN Installation

Technical diagram of a device with numbered components, likely a labeling or assembly view

Control panel

1 Slide the unit into the ISO-DIN frame.
2 Fit screws removed from the old unit.
3 Slide the unit and frame into the dash opening.
4 Install the dash panel or adapter plate.
5 Install the trim ring to the unit.
6 Install the control panel to the unit.

Battery Installation

Illustration of three hands holding test tubes with a syringe, showing step-by-step instructions (no text or symbols)

1 Pull out the battery holder with a sharp product like a ball point pen.
2 Put the battery with an+ cor-rectly on the battery holder.
3 Push the battery holder back into its original position.

Removing the existing receiver unit

Diagram of an electronic component with labeled parts A and directional arrows indicating flow or movement.

If there is already an installation sleeve for the receiver unit in the dashboard, it must be removed.
1 Remove the rear support from the unit.
2 Remove the control panel and trim ring from the unit.
3 Insert the lever ⚠️ into the hole on one side of the unit.

Perform the same operation on the other side and pull the unit out from the mounting sleeve.

• Use only one CR2025 (3V) lithium battery.
• Remove the battery if the remote control is not used for a long period of time.
• Do not leave the product in a hot or humid place.
• Do not handle the battery with metallic tools.
• Do not store the battery with metallic materials.

Connection

Before connecting, make sure that the ignition switch is set to OFF, and remove the battery ⊖ terminal to avoid short circuits.

graph TD
    A["Power Antenna(Blue)"] --> B["Control Relay"]
    B --> C["Amplifier (Optional)"]
    C --> D["B ① Violet / Black Stripe : Rear Right -"]
    C --> E["B ② Violet : Rear Right +"]
    C --> F["B ③ Gray / Black Stripe : Front Right -"]
    C --> G["B ④ Gray : Front Right +"]
    C --> H["B ⑤ Green/ Black Stripe : Rear Left -"]
    C --> I["B ⑥ Green : Rear Left +"]
    C --> J["B ⑦ White/Black Stripe : Front Left -"]
    C --> K["B ⑧ White : Front Left +"]
    L["A ① To Battery(+)(Yellow)"] --> M["Ignition Switch"]
    N["A ② To Ignition(Pink)"] --> O["Dimmer Switch"]
    P["A ③ Remote On(Blue/White)"] --> Q["Amplifier (Optional)"]
    R["A ④ Phone Mute(Orange)"] --> S["Amplifier (Optional)"]
    T["A ⑤ Ground(-)(Black)"] --> U["B ①"]
    V["A ⑥ Power Antenna"] --> W["B ②"]
    X["A ⑦ Dimmer"] --> Y["B ③"]
    Z["A ⑧ Power"] --> AA["B ④"]

A ⑥ : Not connected

CAR CD/MP3/WMA Receiver 9

Basic Operation

	ON PLAYER ON REMOTE
1. Turn the unit on.	PWR	POWER ☒
2. Select a source.	SRC	SRC
3. Adjust the volume.	Rotate PWR	VOLUME ∧ √

Basic operation - more you can do

Mute

Press VOL/MUTE (POWER ☒ on the remote control) to cut the sound. To cancel it, press again.

Using the EQ

EQ is to increase or decrease the signal strength of audio frequencies. The function helps you to enjoy sound more plentifully. Press EQ repeatedly. The indicator lights up in the following order.

POP → CLASSIC → ROCK → JAZZ → VOCAL → SALSA → SAMBA → REGGAE → RUSSY → USER1 → USER2 → Off (not displayed)

Note

- When XDSS+ is set to "Off", you can adjust the EQ settings.

- You can adjust sound level to your preference. Once you select a USER mode and then adjust the sound level, it will be automatically stored for the currently selected USER mode. Refer to the "Adjusting the sound level" for USER 1/2 mode.

Adjusting the sound level

Press SEL (SEL/MENU on the remote control) repeatedly to select the mode you want to adjust from VOL(volume), BAL(left/right speaker), FAD(front/rear speaker) and SUB(Sub-woofer:optional). To adjust sound quality, rotate PWR or press VOLUME on the remote control.

When EQ and XDSS+ is set to "Off", you can also adjust the sound level (BAS(bass), MID(middle), TRB(treble)) settings.

XDSS+ (Extreme Dynamic Sound System)

Press XDSS+. (XDSS+: Improves the treble, bass sound.) To cancel it, press it again.

Checking the clock

You can see the clock pressing DISP (DISP, on the remote control).

Setting the clock

1 Press the DISP(DISP, on the remote control) and then, press and hold it for more 1 second.
2 Press the ▶I+(▶▶▶▶▶ on the remote control) to adjust the hour.
3 Press the -|◀ (|◀◀◀◀ on the remote control) to adjust the minute.
4 Press DISP(DISP. on the remote control) again to finish the setting.

Listening to a CD

	ON PLAYER ON REMOTE
1. Open the front panel.[Only in LAC6910IN/LAC6910INP]		-
2. Insert a CD.	-	-
3. Adjust the volume.	Rotate PWR	VOLUME ▲▼

Listening to a CD - more you can do

Pause or restart a CD

Press ▶|| on the player (▶/|| on the remote control) during playback. Press this button again to resume play.

Search for a section within a track / file

Press and hold -I◄ / ►I+ on the player (I◄◄◄◄/►►►►I on remote control) for about 1 second during playback and then release at the point you want.

Skip to another track / file

Press -I◄ / ►I+ on the player (I◄◄◄◄/►►►►► I on remote control.). To skip to previous track, press briefly -I◄ within 3 seconds of playing time. Press [#] and a number you want to move on remote control to move the files/track.

Intro scan

Press or press and hold INT on the player (INT on remote control). Each files in the current selected folder (■ INT) or the first 10 seconds of each tracks/files (INT) on the disc are played. To cancel it, press the button again.

Repeat

Press or press and hold RPT on the player (RPT on the remote control). The current selected tracks/files (1 RPT) or folder (■ RPT) on the disc is played repeatedly. To cancel it, press the button again.

Shuffle

Press or press and hold SHF on the player (SHF on the remote control). Each files in the current selected folder (■ SHF) or all of the tracks/files (SHF) on the disc is played randomly. Press SHF again to cancel it.

During random playback, if you press -I◀, you won't go back to the previous track.

MP3/WMA Track -10 / +10

(If there is no folder or one folder.) During playback push the button down to V/PS to go back 10 tracks, or push it up to ^AS to go forward 10 tracks.

MP3/WMA Folder UP/DOWN

(If there are more than two folders.) During playback, push the button down to v/PS to go back to the previous folder, or push it up ∧ AS to go forward to the next folder.

Checking information about your music

MP3/WMA files often come with tags. The tag gives the Title, Artist or Album. Press DISP repeatedly during MP3/WMA/CD TEXT file playback. If there is no information, "NO TEXT" will be shown in the display window.

• The icon is displayed during MP3/WMA playback.

- MP3/WMA Disc compatibility with this unit is limited as follows:

1. Sampling Frequency / 8 - 48kHz (MP3) 22.05 - 48kHz (WMA)
2. Bit rate / within 8 - 320kbps (include VBR) (MP3) 32 -320kbps (WMA)
3. CD-R/CD-RW file system should be "ISO 9660"
4. If you record MP3/WMA files using software which cannot create a FILE SYSTEM, for example "Direct-CD" etc., it will not be possible to playback MP3/WMA files. We recommend that you use "Easy-CD Creator" which creates an ISO9660 file system.

Customers should also note that permission is required in order to download MP3/WMA files and music from the Internet. Our company has no right to grant such permission. Permission should always be sought from the copyright owner.

Listening to the radio

	ON PLAYER ON REMOTE
1. Select a source to tuner.	SRC	SRC
2. Select a band.	BAND	←/BAND
3. Auto seek.Manual seek.	-|◄/►|+	|◄◄◄◄/►►►►|
	Press and hold-|◄/►|+	Press and hold|◄◄◄◄/►►►►►|

Listening to the radio - more you can do

Auto search memory

Push the button up to ∧/AS. The six strongest broadcast frequencies will be stored under preset button 1-6 in the order of their signal strength. To cancel, push the button up to ∧/AS.

Storing and recalling broadcast frequencies

1 Press BAND to select desired band you want to store.
2 Select the desired frequency and press one of preset buttons 1-6 and hold until the beep sound.
3 Repeat steps 1-2 to preset other stations. The next time, you press the same preset button, the radio station frequency is recalled from the memory.

To scan the preset stations

Push the button down to V/PS. Each preset station appears. To cancel, push the button down to V/PS.

To tune in the preset stations

Press BAND to select the desired band and press the desired preset button 1-6 (preset button 1-6 on the remote control).

Note

- When a station is stored on the preset numbers on which another station of the same band has already been preset, the previously preset station is automatically erased.

Connecting USB device

	ON PLAYER ON REMOTE
1. Open the USB cover.	-	-
2. Connect the USB device.	-	-
3. Adjust the volume.	Rotate PWR	VOLUME ▲▼

Moving to another drive

When connecting this unit to multi reader, press BAND (BAND/DRV on remote control) to go to the next drive. Each time you press the button, the driver modes changes.

Note

• If the USB device is already connected, press SRC (SRC on remote control.) to select a source to USB.
• Pause / Intro Scan / Repeat / Shuffle / ... functions are same with "Listening to a CD - more you can do". Refer to the page 11.

Listening to music by connecting iPod

You can enjoy iPod-stored music on the unit by connecting it to the USB connector using the appropriate cable.

Not Supplied

	ON PLAYER ON REMOTE
1. Open the USB cover.	-	-
2. Connect the iPod.	-	-
3. Adjust the volume.	Rotate PWR	VOLUME ▲ ▼

Note

• If the iPod is already connected, press SRC (SRC on remote control.) to select a source to USB.
• Refer to the page 16 to check the compatible iPod model for this unit.
• Repeat, Shuffle, Checking music information functions are only in track number display mode.

Listening to music by connecting iPod

- more you can do

Pause or restart playback

Press ▶II on the player (▶/II on the remote control) during playback. Press this button again to resume play.

Shuffle

Press or press and hold SHF on the player (SHF on the remote control). Each files in the current selected folder (■ SHF) or all of the tracks/files (SHF) on the iPod are played randomly. Press SHF again to cancel it.

Repeat

Press RPT on the player (RPT on the remote control). The current selected tracks/files (1 RPT) on the iPod is played repeatedly. To cancel it, press the button again.

Note

During playback, if you press -I◄/►I+ , you won't go back to the previous or next track.

Checking music menus

1 Press iPod MENU/BAND (BAND/DRV/iPod MENU on remote control) once to move to the music menu display mode.
2 Push the button up to U/AS or down to u/PS(UA) on remote control) to select a music menu list. Then, the menu display modes change as follows. (PLAYLISTS | ARTISTS | ALBUMS | GENRES | SONGS | COMPOSER | AUDIO BOOK | PODCAST)
3 Press ▶I+(▶▶▶▶ on remote control) to confirm the music menu.
4 Push the button up to U/AS or down to u/PS(U/AS on remote control) to select a file and press ▶I+(▶▶▶▶▶ on remote control) to confirm it. - Press -I◀(I◀◀◀◀ on remote control) to return to the previous menu.

Checking information about your music

MP3/WMA files often come with tags. The tag gives the Title, Artist or Album. Press DISP repeatedly during MP3/WMA file playback. If there is no information, "NO TEXT" will be shown in the display window.

Changing iPod settings

1 Press iPod MENU/BAND (BAND/DRV/IPod MENU on remote control) twice and then ▶I+(▶▶▶▶▶ on remote control) to change iPod settings.
2 Push the button up to U/AS or down to u/PS(U/UR on remote control) to select a setting item. Then the setting items change as follows. (REPEAT <-> SHUFFLE <-> BOOK SPEED)
3 Press ▶I+(▶▶▶▶ on remote control) to confirm the item.
4 Push the button up to U/AS or down to u/PS(U/UT on remote control) to adjust values and press ▶I+(▶▶▶▶▶ on remote control) to confirm it.
- Press -I◀(I◀◀◀◀ on remote control) to return to the previous menu.
- The setting values are as follows.
- REPEAT (RPT ALL <-> RPT 1 <-> RPT OFF)
- SHUFFLE (SHF OFF <-> SHF ALBUM <-> SHF ALL)
- BOOK SPEED (Audio book speed: SLOWER <-> NORMAL <-> FASTER)

Connecting an Auxiliary Equipment

Auxiliary input MP3 Player, etc Line out

	ON PLAYER ON REMOTE
1. Select a source to AUX.	SRC	SRC
2. Play the connected Auxiliary Equipment.	-	-
3. Adjust the volume.	Rotate PWR	VOLUME ▲▼

Changing settings

	ON PLAYER ON REMOTE
1. Select one item.	Press MENU	Press and hold SEL/MENU
2. Select a source.	Rotate PWR	VOLUME ▲ ▼
3. Finish the setting .	Press MENU	Press SEL/MENU

● AUX (Auxiliary) ON / OFF

It is possible to use auxiliary equipment with this unit. Activate the auxiliary setting when using auxiliary equipment connected to this unit.

● AUX (Auxiliary) 00dB / +6dB

Ony when you set AUX to ON as switching sources, you can adjust the volume level of each source to prevent radical changes in volume. You can set to 0 dB or +6 dB. You may be surprised at a loud sound when you change the source from the external component to another source.

● DEMO OFF/ ON You can change the initial indication on the display to information name (function name, EQ name, etc...) while listening to a source.

LCD WHI / RED

You can change the LCD window color. WHI(white) <-> RED(red)

● [LAC5910IN/LAC5910INP] LED RED / GRN / AUTO [LAC6910IN/LAC6910INP] LED BLU / RED / AUTO

You can change the button color.

• COL TM (Color changing time)

Only when you set LED to AUTO, you can set LED color changing time from 5 to 60 seconds.

- SW(Subwoofer) OFF / SW 55HZ / SW 85HZ / SW 120 HZ You can enable the subwoofer.

SW OFF <-> SW 55HZ <-> SW 85HZ <-> SW 120 HZ.

• DIM(Dimmer) OFF / ON / AUTO

You can change the brightness of the display window during the power-on status. When you set DIMMER to AUTO, the dimmer operates according to the car dimmer setting.

• DIM L (Dimmer Level)

When you set DIM to ON/AUTO, you can adjust the dimmer level. (-2,-1,0,+1,+2)

AUTO EQ operates only in the music file supported with Genre in the device. When you set AUTO EQ to ON, POP, CLASSIC, ROCK, or JAZZ is automatically according to the music genre.

BEEP 2ND / ALL

BEEP 2ND : The beep is generated when a key is long pressed. (1 sec) BEEP ALL : The beep is generated when any key is pressed.

Troubleshooting

	Symptom Cause Correction
General	Power doesn't turn on / The unit doesn't operate.	Leads and connectors are not properly.	Confirm once more that all connections are correct.
		The fuse is blown.	Rectify the problem that caused the fuse to blow, and then replace it. Be very sure to install the correct fuse with the same rate.
		Noise and other factors are causing the built-in microprocessor to operate incorrectly.	Turn the unit off and then on.
	No sound is heard / The volume level will not rise.	Cables are not connected correctly.	Connect the cables correctly.
CD	There's audio skipping.	This unit is not firmly secured.	Secure this unit firmly.
	The playback is not possible.	The disc is dirty.	Clean the disc.
		The loaded disc is of a type this unit cannot play.	Check what type the disc.
Radio	Radio stations cannot be tuned in.	The signal strength of the stations is too weak(when tuning in with automatic tuning.)	Tune in the stations manually.
		No station has been preset or preset stations have been cleared(when tuning by scanning preset stations.)	Preset the stations.(Refer to the page 12)
iPod	iPod does not work.	Check whether the player is connected to the unit correctly.	Connect it to the unit correctly.
Remote control	The unit does not operate correctly even when the appropriate remote control buttons are pressed.	Battery power is low.	Load new battery.

Specifications

General

Output Power 53W x 4CH (Max.)

Power Source DC 12V

Speaker impedance 4Ω

Ground System Negative

Dimensions (W x H x D) 180 x 50 x 176 mm (Without Control Panel)

Net Weight 1.3 kg

Tuner

FM

Frequency Range 87.5-107.9, 87.5-108 MHz

S/N Ratio 55 dB

Distortion 0.7%

Usable Sensitivity 12 dBμV

AM (MW)

Frequency Range 520-1720 or 522-1620 kHz

S/N Ratio 50 dB

Distortion 1.0%

Usable Sensitivity 28 dBμV

CD

Frequency Response 20 Hz-20 kHz

S/N Ratio 80 dB

Distortion 0.12%

Channel Separation (1kHz) 55 dB

AUX

Frequency Response 20 Hz-20 kHz

S/N Ratio 80 dB

Distortion 0.1 %

Channel Separation (1kHz) 45 dB

Max Input Level (1kHz) 1.1V

USB

Version USB 1.1

Line OUT

Frequency Response 20Hz \~ 20 KHz

Output Voltage 1.8 V (Max.)

Subwoofer (optional)

Frequency Response 20Hz \~ 120 Hz

Output Voltage 1.8 V (Max.)

Compatible iPod models

• iPod touch
• iPod classic
• iPod with video (5th generation)
• iPod nano (1st generation)
• iPod nano (2nd generation)
• iPod nano (3rd generation)

Designs and specifications are subject to change without notice.

P/NO : MFL61778403