RTT 281WSZ-19 - Washing machine CANDY - Free user manual and instructions

USER MANUAL RTT 281WSZ-19 CANDY

• Please read this manual carefully before using.
• Retain it for future reference. 0030516071

Contents

♦ Safety precautions.... 2
♦ Packing list.... 4
♦ Machine components...... 4
♦ Installation and adjustment.... 5
♦ Pre-wash preparation.... 7
♦ Washing sequence.... 9
♦ Disposal after washing 12
♦ Troubleshooting....41
- Specifications......Back cover

Safety precautions

Meaning and description of the symbols

WARNING

Contents marked with this symbol relate to product and user safety. Please operate the machine in strict conformity to the contents of this manual to minimize the risk of personal injury and/or damage to the machine.

FORBIDDEN

Contents marked with this symbol describe actions prohibited to perform. If performed these actions will endanger the user's personal safety and may result in injury.

Please insert the power cord into a rated voltage outlet. Be sure to use a single-phase three pin outlet. Also, the terminal of the outlet must be grounded. If possible, please install an electric leakage protector.

When the machine is in use, place the power plug in a location where it can be easily inserted and extracted by hand. Be sure to remove the plug if power failure occurs, when moving or cleaning the machine, or when the machine is idle.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

Use only the supplied hose set for the connection. Never reuse old hose sets!

Do not place the machine in a damp place like the bathroom and never wash it with water. Do not place wet laundry on the control panel.

Illustration showing a hand cleaning a container with a 'no' symbol, indicating no proper action or absence of the text.

If the washing machine is installed on the ground near carpet, make sure to keep the ventilation hole clear of obstruction.

Technical diagram of an electronic circuit board with labeled components and connections

Ventilation hole atthe bottom of the washing machine

Do not use water warmer than 50 °C .

Illustration of a person washing clothes inside a kitchen appliance (no text or symbols)

To avoid abnormal vibrations in spinning, do not use the machine to wash water-proof laundries like raincoats, bike covers etc.

Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. Take special care of the children. This appliance is not intended for use by persons (including children) with educe physical, sensory or mental capabilities of, lack of

experience and knowledge, unless they have been givensupervision or instruct concerning use of the appliance by a person responsible for their safety.

ion

Do not share the outlet with other electric appliances. If the power plug is damaged, or feels loose when plugged into the

outlet, stop using the plug immediately.

Diagram showing a hand holding a device with a prohibition symbol below, indicating no protection or disapproval.

Do not put any high temperature or heavy objects on the washing machine.

Cartoon illustration of a distressed bottle character with steam and a crossed-out circle symbol (no text or labels)

Do not attempt to take apart, repair or alter the machine by yourself.

Cartoon illustration of a person standing next to a distressed refrigerator with lightning bolts, next to a no-smoking symbol (no text or labels)

Disabled children or those not under adult supervision should not operate

the machine.

Cartoon illustration showing a smiling child waving next to a smiling container, with a prohibition symbol nearby.

Do not wash laundry with volatile or flammable materials (such as thinner,

petrol etc.).

Patagon No. 100% No. 100%

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Keep the machine away from direct sunlight and heat sources like the

radiator.

Illustration showing a cartoon character holding an umbrella with a crying face, standing beside a device emitting exhaust smoke, and a no-smoking symbol nearby.

This appliance is intended to be used in household and similar applications such as:

– staff kitchen areas in shops, offices and other working environments;
- farm houses;
– by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments;
- areas for communal use in blocks of flats or in launderettes.

● To guarantee your safety, please ensure the power outlet is grounded before use.

- To protect your laundry and the washing machine, please remove all coins, buttons, sand, hairpins and other foreign materials before washing.

• Please check if the water faucet is turned on and make sure you have the proper water pipe connection
• It is recommended to use foamless washing powder.

Packing list

Twin-tub washing machine

Water intake hose

Gland

Lint filter ( only on model RTT 281WSZ-19 )

Owner's manual

manual

Machine Components

Wash time

If you wish to set it for less than 2 min, you should first turn past 6 min and then turn back.

Wash selector

Intensity can be set to standard, soft and drain.

Spin time

If to set to less than 1 min, in order to ensure a long service life, please first turn past 2 min and then turn back.

Control panel

0 5 45 10 SOFT 15 30 STANDARD DRAIN WASH TIME WASH SELECTOR

0 5 1 4 2 3 SPIN TIME

Wash Timer Selector Wash Type Selector Water Inlet Port Water Inlet Selector Control Panel Lint Filter (must be installed by the end user) Overflow Filter Washing Tub Drain Hose Outer Cover of the Spinning Tub Inner Cover of the Spinning Tub Main Frame Spinning Tub Cabinet Base Frame

Important notes:
- All illustrations contained in this manual have a reference purpose only. Your washing machine as well as the accessories may look different from these illustrations.

Installationandadjustment

For your security and to ensure correct operation of the machine, please install and adjust the machine according to this manual's instructions.

Installation of the lint filter

Place the bottom side of the lint filter into the overflow filter, then push the top side into the overflow filter.

• After installation, please double check to make sure that the lint filter is installed in the correct location; otherwise it may fall off during operation. (on models RTT 2101WSZ-19)
• After unpacking your washing machine, take out the lint filter from the documentation bag. Install the lint filter in the overflow filter located inside the washing tub. See the illustration. (on models RTT 281WSZ-19)

overflow filter lint filter

overflow filter lint filter

Drain hose usage

Drain hose drainage should be smooth and unobstructed.

1. The height of the drain hose shall be less than 10cm, or the drainage will not be smooth enough and cause incomplete drainage.
2. Do not tramp or press the drain hose.
3. If the drain hose is too long, cut it at mid point. To make smooth drainage, cut the front end of the hose slantingly.
4. If extra drain hose is needed, please make separate purchase. The inner diameter of the extra hose shall not less than 30mm, and the length shall not exceed 1.5m.

If the extra hose is too long, cut it either at point A or B.

Illustration showing a hand using a tool to mark a small object on a surface, with an inset close-up of a mechanical component (no text or symbols)

≥30mm ≤1.5m

Change the direction of the drain hoses

Figure 1 shows the factory installation position of the drain hose.

Drain Hose Fixing Hook

Figure 1

Extend the drain hose from the spin tub side:

1. Remove the drain hose from the hanging hole on the cabinet. Pull the drain hose fixing hook outwards gently to take out the drain hose from the two fixing hooks.(See Figure 2.)

Side Section View Drain hose fixing hook Fixing hook installation hole Drain hose Slightly pull out Take off drain hose

Figure 2

1. Turn 90° the drain hose fixing hookto remove it from the installation hole.(See Figure 3.)

Turn 90° the fixing hook Take off the fixing hook downwards

Figure 3

1. Install the two drain hose fixing hooks taken out, into the installation hole at the other side of the base frame (to aim at the installation hole accurately you can lean the washing machine forward slightly). Then turn 90°.(See Figure 4.)

Turn 90° the hook to fix it Insert the fixing hook into the Installation hole upwards

Figure 4

Install the water intake hose

• Insert the water intake hose into the water-inlet entrance on the control panel.
• Add water as necessary.

Water intake hose Water inlet

Pre-wash Preparation

Basic know-how

- The maximum capacity during washing and spinning cycles refers to the max weight of standard dry laundry that can be washed or spun at one time. The laundry quantity during one washing cycle should be lower than the rated capacity.

- Thickness, size, and the type of cloth will influence actual washing capacity. It is acceptable to put in a reasonable amount of laundry as the laundry will be mixed around during the washing process.

- To avoid splashing, do not select the "Maximum" water level for low loads.

• Using high sudsing detergent is not recommended.

Illustration of a woman cleaning a washing machine with a smiling face (no text or symbols)

Pay attention to followings before washing the laundries

Check to see if the items have special washing requirements.

Put hard to absorb water items into the machine by hand.

Empty out pockets. Take out any coins, sand, hairpins

Check to see if the items are appropriate for use with the washing

Do not overload the washer. Stretch and loosen the laundry before putting it into the washer.

For laundry that is susceptible to lint balls and/or has long fur, turn it inside out before putting it in the washer.

Do not put laundry polluted by chemicals into the washing machine directly.

For heavily soiled laundry, try to remove dirt such as mud or dust first and apply detergent in advance. This will help to remove the stains more easily.

Divide non-colorfast laundry from other laundry.

When the pulsator is running, some noise may emit from laundry that contains buttons. To minimize this noise, surround laundry with buttons with other laundry.

Simple line drawing of a person's face with expressive eyes and a serrated mouth, no text or symbols present.

Detergent use

How to add detergent:

- Method 1 - directly dissolving in the machine:

1. Add a small quantity of water to the machine.
2. Add the detergent powder. Run washing machine for 30 seconds to dissolve powder completely.
3. Place laundry into the washing machine and select a suitable water level.

- Method 2 - instantly dissolving the detergent powder:

1. Prepare warm water at 30^ C and a container.

2. Add the detergent powder while stirring until it dissolves fully.

3. Laundry powder is more prone to damage laundry than liquid detergent. Please exercise

4. caution and do not exceed the maximum quantity.

Dosages of detergent powder may vary. Please follow the instructions on the detergent.

Using bleach detergent:

• Add water to suitable levels. Dilute the bleach with a separate container. Pour it slowly into the washing machine.
• Avoid using whitening agents on laundry with colors and/or patterns as they are prone to lose color.
• The whitening agent should not come in direct contact with the laundry.
• Refer to the product instructions for information on proper usage and quantity
• Dissolve powder whitening agents before use.

Note:

The energy test program(RTT 281WSZ-19):

Full load Cotton 60: Manually fill in hot water (23 to 24 liters) and cold water up to the 4 water level, after Standard wash 45min, then keep washing 30min, Drain, Spin twice, each for 5min, 5min cold rinse with 4 water level, Drain, Spin twice, each for 5min; Partial load Cotton 60: Same as Full load Cotton 60 but with 15 to 16 liters hot water in washing process and spin once after washing and rinsing; Water level select 1; Partial load Cotton 40: Same as Full load Cotton 60 but with 12 to 13 liters hot water in washing process and spin once after washing and rinsing; Water level select 1; The energy test program (RTT 2101WSZ-19):

Full load Cotton 60: Manually fill in hot water (28 to 29 liters) and cold water up to the MED water level, after Standard wash 45min, then keep washing 30min, Drain, Spin twice, each for 5min, 5min cold rinse with MED water level, Drain, Spin twice, each for 5min;

Partial load Cotton 60: Same as Full load Cotton 60 but with 21 to 22 liters hot water in washing process and spin once after washing and rinsing; Water level select BZ; Partial load Cotton 40: Same as Full load Cotton 60 but with 17 to 18 liters hot water in washing process and spin once after washing and rinsing; Water level select BZ;

Washingsequence

Washing

1. Inlet se lector

Set the selector to "WASH".(Figure1)

WASH SPIN

Figure 1

2.Add water

Machine begins to dispense detergent uniformly.(Figure2)

Line drawing of a kitchen appliance with a bowl pouring liquid from a pan (no text or symbols)

Figure 2

3. Put in the wash load. Add more water as necessary.(Figure3)

Line drawing of a kitchen sink with a person standing on top (no text or symbols)

Figure 3

4 Select intensity..

Select "SOFT" or "STANDARD" water flow intensity according to the wash load.(Figure4)

STANDARD SOFT. DRAIN WASH

Figure 4

5. Select wash time.

Select wash time according to the wash load. (Figure5) The washing instruction with soaking:

Figure 5

(1) 0-15 minutes is normal washing;
(2) 15-45 minutes is sport soaking and the pulsator will run 2.5 minutes each 7.5 minutes interval, until sport soaking is end, finally it is 15 minutes normal washing;
(3) When the user select the soaking, firstly make sure the detergent power is fully dissolved. Otherwise it may be harmful to clothing.

6. After the wash is completed, set the switch to the "DRAIN" position.(Figure6)

STANDARD SOFT DRAIN WASH

igure 6

Mid-wash spin cycle

1. Put the laundries into the spin tub evenly and smoothly.
2. Spin : (1) Distribute the laundry into the spin tub smoothly and evenly.

Note: the gland must be inserted properly even if the laundry quantity is small.

Push Gland Proper The laundry is slanted. Push Proper No gland

(2) Close both the inner and outer covers of the spin tub.
(3) Spin for 1-2 minutes.

Outer cover of The spin tub

Inner cover of The spin tub

Pure technical line drawing of a mechanical component with no text or symbols

1. Run the foam-removing spinning.

(1) Open the outer cover of the spin tub. (2) Set the water-filling selector control rod at the "SPIN" side. Fill water for about 1 minute.

If the water quantity filled is too large, the water may flow out from the wash tub side. Please twist the water tap to limit the water filling.

(3) Close the outer cover of the spin tub. Spin for 1-2 minutes.

WASH ←→ SPIN

The rinse cycle

Rinse with water-filling

1. Place laundry into the washing machine.

Place laundry into the washing machine. Select the appropriate current according to the laundries.

2.Add water.

Add the appropriate amount of water.

3.Rinse

Adjust the wash timer to 5-7 minutes for the rinse cycle.

Rinsing with stored water

(Repeat the mid-wash spin cycle and rinse cycle with stored water 2-3 times)

1. Place laundry into the washing machine. Select the appropriate current according to the laundries.

2. Fill up water to the preset level.

3.Rinse.

Adjust the wash timer to 2-3 minutes for rinsing.

When the laundry quantity is low, use the "SOFT" current. If you use the "STANDARD" current, the water may splash.

Spinning

1. Distribute laundry into the spin tub evenly and smoothly.

2. Insert the gland into the tub properly.

Close the inner and outer cover of the spin tub.

3.Spin.

Select an appropriate spin time according to the condition of the laundry, and start the spinning cycle.

- During the spinning cycle, if any abnormal sound occurs, it is generally due to the laundry being placed in a slanted fashion. Please stop the machine and re-arrange the laundry accordingly.

- During the spinning cycle, the machine will pause if the outer cover of the spin tub is opened. Close it to resume the spinning cycle.

Simple line drawing of a person pointing upward (no text or symbols)

To run spinning and draining or rinsing with water-filling one after the other, first run the spinning cycle for around 1 minute, then draining or rinsing with water-filling. Otherwise the water-filling. Otherwise the water-filling. Otherwise the spinning will stop automatically because of the excess water in the spin tub.

Disposal after washing

• After each use, be sure to clean the lint and foreign materials from the lint filter and the overflow filter in a timely fashion. Removing lint is important for healthy operation of the machine.
• Please remove the plug from the power outlet first before cleaning.

Cleaning the lint filter

The lint filter should always be used during washing and should be cleaned after each use in a timely fashion.

On model RTT 2101WSZ-19.

1. To remove the lint filter, first press the elastic piece at the upper end of the filter to release the tab from the filter cover, then pull outward.

1. Pull the lower end of the lint filter rear cover outward to separate it from the lint filter front cover. Remove lint completely by rinsing with clear water.

Lint filter back cover Disassemble Assemble Lint filter front cover

1. Re-install the lint filter.

On model RTT 281WSZ-19.

1. Remove the lint filter. Place your hand in the shown position. Push down to remove the filter.

1. Remove collected lint. Place the filter in water and remove lint while wet.

1. Re-install the lint filter.

Cleaning the overflow filter

Too much lint in the overflow filter will influence normal usage of the machine.

Remember to clean it once every two months.

On model RTT 2101WSZ-19.

1. Take off the overflow filter.

Nip the elastic fixing claw and pull in the direction of the arrow to remove (as demonstrated in the figure to the right).

1. Clean the overflow filter.

Clean the lint around the filter and flush with tap water.

1. Re-install the overflow filter.

1) Install the corrugation pipe.
2) Attach the mounting plate at the bottom of the filter into the valve cover.
3) Hang the hook on the left upper side.
4) Push in the upper part.

On model RTT 281WSZ-19.

1. Take off the overflow filteras shown in the figure.
   Nip the elastic fixing claw and pull it in the direction of the arrow to take it off.

2. Clean the overflow filter.

Clean the lint around the filter and flush with tap water.

1. Re-install the overflow filter.

1) Install the corrugation pipe.
2) Attach the mounting plate at the bottom of the filter into the valve cover.
3) Hang the hook on the left upper side.
4) Push in the upper part.

Elastic fixing claw

Water level selection lever Corrugated hose

Hook

Elastic fixing claw

Cleaning the unit

• Wipe the entire unit with a soft dry cloth.
• Use neutral detergent to wipe if the machine is excessively dirty.
• Do not apply water directly when cleaning.

Alcohol Petrol Thinner

• After washing, disconnect the water intake hose.
• Do not store water in the machine for long periods of time. Drain the water immediately after each use.
• Pull out the power plug and hang up the power cord.
• Hang up the drain hose. Wipe off water drops on the surface and inside the machine with a clean soft cloth.
• Open the cover of the wash cycle compartment and the inner/outer covers of the spin cycle compartment for a short period (about one hour), then close them.

Troubleshooting

When the remaining water is frozen

Pour hot water below 50°C into the wash cycle compartment to soak it completely, then using your hands gently turn the pulsator. Confirm that the drainage function is operating normally before next use.

Below 50°C 2~3L

Prevent the freezing

(be sure to drain the water completely after each use) After completely draining, set the "WASH SELECTOR" to "STANDARD". If it is set to "DRAIN", it will be difficult for the frozen water to melt.

(If a breakdown occurs, always pull remove the power plug before inspecting the machine) The following situations do not always indicate a breakdown. Please double confirm before sending the machine to be repaired.

If an actual breakdown occurs, visit the special maintenance department or after-sales service department of our company. Do not attempt to repair the machine by yourself.

Phenomena The reason
The machine does not start.	Is there a power failure?Is the power plug loose?Is the pulsator twisted by foreign materials?
The draining function does not work	Is the drain hose put down?Is the drain hose frozen?Is the drain hose blocked by foreign material?Is there laundry adhering to the outer side of the spin tub?
Abnormal sound during washing	Are there hair pins, coins or metal items inside the tub?
Abnormal sound and violent vibration during the spin cycle	Is the machine slanting?Is the gland pressed evenly?Is there laundry adhering to the outer side of the spin cycle compartment?Is the spin cycle compartment overloaded?
Water flowing out of the drain hose during the first use of the machine.	This is the water left over after the factory performance inspection.
The spin part does not work	Is the spin tub outer cover open?

Specifications

Model RTT 281WSZ-19 RTT 2101WSZ-19
Rated Voltage 230V~ 230V~
Rated Frequency 60Hz 60Hz
Washing Capacity 8kg 10kg
Spin-dry Capacity 5kg 6kg
Rated Wash Power 390W 400W
Rated Spin Power 150W 150W
Total Input Power	540W 550W
Rated Current of Fuse	5A	5A
Degree of Water-Proof	IPX4	IPX4
Rated Annual Energy Consumption	283kWh	348kWh
Rated Annual Water Consumption	20680L	26180L
Net Weight	23.5kg	25kg
Dimensions	(825×470×990)mm	(865×500×995)mm
Injection pressure	0.02 - 0.2MPa	0.02 - 0.2MPa
Water level/Water quantity (approximately)	MAX/76L,5/70L,4/63L, 3/57L,2/50L,1/43L	MAX/89L,MED/76L, MIN/65L

MADE IN CHINA

CANDY ME FZE

Office 713, Block 4WA,

Dubai Airport Free Zone, Dubai,

United Arab Emirates,P.O. Box 54954

Tel: [phone]

Fax: [phone]

www.candy.ae

Hand holding a device with a triangular pointer and a separate cylindrical component, no visible text or symbols

Hand inserting a card into a computer monitor (no text or symbols visible)

Simple line drawing of a person pointing upward (no text or symbols)

Line drawing of a kitchen appliance with a bowl pouring liquid from a handle (no text or symbols)

Illustration of a woman washing clothes at a kitchen appliance (no text or symbols)

Simple line drawing of a person's face with a serrated edge and textured mouth (no text or symbols)

Cartoon illustration of a hand pointing at a computer monitor with a sad face, next to a pen writing on paper (no text or symbols present)

-9 1.5 30mm

Safety warning symbol showing no prohibition sign and hand holding a device with multiple sensors

Cartoon illustration of a man standing next to a distressed refrigerator with a sad face (no text or symbols)

Cartoon illustration of a distressed refrigerator with steam and a surprised face (no text or symbols)

Diagram showing a collection of gas and chemical products including a jacket, a fuel can, and a bottle labeled 'Petroxol' and 'Zerzo'.

Cartoon illustration showing a book character with sad expression, holding an umbrella, and a warning symbol with sun and smoke.

Safety warning illustration showing a hand cleaning a device with a 'no sign' symbol and a paint bucket.

Simple line drawing of a bell and a prohibition symbol (no text or labels)

Line drawing of a person washing clothes inside a washing machine (no text or symbols)

المحتويات