GPF18W - Kit de porte pour lave-vaisselle GE - Free user manual and instructions
Find the device manual for free GPF18W GE in PDF.
User questions about GPF18W GE
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Kit de porte pour lave-vaisselle in PDF format for free! Find your manual GPF18W - GE and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. GPF18W by GE.
USER MANUAL GPF18W GE
Installation Instructions
GSM1800JBB, Black Trim Kit GSM1800JWW, White Trim Kit
GPF18 Series Kits
Before you begin - Read these instructions completely and carefully.
IMPORTANT: Save these instructions for local inspector's use.
IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.
NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer.
NOTE TO CONSUMER: Keep these instructions with your Owner's Manual for future reference.
WARNING
To prevent electric shock, disconnect electrical power supply to dishwasher before changing panels. Do not operate dishwasher while changing panel.
CAUTION
The dishwasher will tip over when the door is opened. Hold the top of the dishwasher securely with one hand and hold the door with the other hand.
Tools and Materials Required:
• Phillips screwdriver
- Gloves to protect against sharp edges
- Safety glasses
The GPF18 trim kits provide for the installation of a 1/4" thick custom door panel.
This kit includes:
Fully Assembled Door Panel Frame
natural_image
Technical line drawing of a rectangular frame with internal supports and mounting holes (no text or symbols)STEP 1 CUT 1/4" THICK CUSTOM PANEL TO SIZE
- Cut door panel to the dimensions shown in Figure 1.
NOTE: The trim provided will conceal the cut edges of the panel.
text_image
1/4" Thick Door Panel 22-1/8" 17-1/4"Figure 1
STEP 2 REMOVE DOOR PANEL
- Open dishwasher door.
- Remove the 6 Phillips head screws along the side of the door (Figure 2) holding the inner door to the outer panel. Retain screws.
- Remove door panel.
NOTE: To prevent any damage, support the outer door panel while removing the screws.
natural_image
Technical line drawing of a mechanical assembly with mounting brackets and mounting holes (no text or symbols)Figure 2
STEP 3 ASSEMBLE PANEL AND TRIM FRAME
- Slide the 1/4" custom panel into the channel between the trim and the steel panel (figure 3).
- Place the assembled panel, appearance side down on a flat protected surface. Be careful not to scratch the custom panel or the trim.
text_image
Slide Panel Into Frame Top View Custom PanelFigure 3
STEP 4 INSTALL THE ASSEMBLED PANEL
text_image
Escutcheon Escutcheon Tab Figure 4Figure 4
- Close the dishwasher door.
- Slide the panel assembly into the escutcheon tab (Figure 4).
natural_image
Technical line drawing of a mechanical assembly with mounting brackets and mounting holes (no text or symbols)While supporting the door kit asm.
Figure 5
- Open the dishwasher door and reinstall the original 6 Phillips head screws to attach the inner door to the trim kit assembly (Figure 5).
- Close the door.
STEP 5 CHECK DOOR BALANCE
To check the door balance, hold the top of the dishwasher firmly.
- Open the door slowly, if the door drops faster than desired when released, increase spring tension. If the door closes too quickly when released, decrease tension.
To adjust spring tension:
• Make sure door is closed
- Unhook springs from adjustment pins
- Relocate adjustment pin up (to increase tension) or down (to decrease tension) as desired.
- Hook door springs to adjustment pins.
- Open and close door to check door balance.
- Repeat adjustment if required.
NOTE: Make sure both springs have the same tension settings.
text_image
Increase Decrease Figure 6Drawing #
206C1559P122
Pub. No. 31-30582