XND-8081RV - Security Camera Wisenet - Free user manual and instructions

USER MANUAL XND-8081RV Wisenet

©2019 Hanwha TechwinCo., Ltd. All rights reserved.

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.

Disclaimer

Hanwha Tochwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user's own responsibility. Hanwha Tochwin reserves the right to change the contents of this document without prior notice.

❖ Design and specifications are subject to change without prior notice.

The initial administrator ID is "admin" and the password should be set when logging in for the first time.

Please change your password every three months to safely protect personal information and to prevent the damage of the information theft.

Please, take note that it's a user's responsibility for the security and any other problems caused by mismanaging a password.

important Safety inStructionS

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.)
7. Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. This product is intended to be supplied by a Listed Power Supply Unit marked "Class 2" or "LPS" and rated from 12 Vdc, 0.45 A or PoE, 0.15 A. (XND-6081V/F)
16. This product is intended to be supplied by a Listed Power Supply Unit marked "Class 2" or "LPS" and rated from 12 Vdc, 0.90 A or PoE, 0.27 A. (XND-6081RV/RF)
17. This product is intended to be supplied by a Listed Power Supply Unit marked "Class 2" or "LPS" and rated from 12 Vdc, 0.97 A or PoE, 0.30 A. (XND-8081RV/RF)
18. This product is intended to be supplied by a Listed Power Supply Unit marked "Class 2" or "LPS" and rated from 12 Vdc, 0.45 A, 24 Vac, 0.58 A, or PoE, 0.15 A. (XNV-6081)
19. This product is intended to be supplied by a Listed Power Supply Unit marked "Class 2" or "LPS" and rated from 12 Vdc, 0.90 A, 24 Vac, 0.97 A, or PoE, 0.27 A. (XNV-6081R)
20. This product is intended to be supplied by a Listed Power Supply Unit marked "Class 2" or "LPS" and rated from 12 Vdc 0.97 A, 24 Vac, 1.10 A, or PoE, 0.30 A. (XNV-8081R)

21. If you use excessive force when installing the product, the camera may be damaged and malfunction. If you forcibly install the product using non-compliant tools, the product may be damaged.

22. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or near the kitchen table.
    This may cause damage to the product.

23. When installing the product, be careful not to allow the surface of the product to be stained with chemical substance.
    Some chemical solvents such as cleaner or adhesives may cause serious damage to the product's surface.
24. If you install/disassemble the product in a manner that has not been recommended, the production functions/performance may not be guaranteed.
    Install the product by referring to "Installation & connection" in the user manual.
25. Installing or using the product in water can cause serious damage to the product.
26. Although a rapid change in temperature could cause frost inside the dome, there will be no problem with the video.

warningG

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

caution

caution

riSK of eElectric SHocK. Do not open

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

eXpLanation of GrapHicaL SymBoLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

overview

Class I construction

An apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

The battery cannot be replaced.

Disconnection Device

Disconnect the main plug from the apparatus, if it's defected. And please call a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.

CAUTION

These servicing instructions are for use by qualified service personnel only.

To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Please use the input power with just one camera and other devices must not be connected.

The ITE is to be connected only to PoE networks without routing to the outside plant.

The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3af shall be a UL Listed device with the output evaluated as a Limited Power Source as defined in UL60950-1.

Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102. As such, associated Ethernet wiring shall be limited to inside the building.

Please read the following recommended safety precautions carefully.

• Do not place this apparatus on an uneven surface.
• Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area.
• Do not place this apparatus near conductive material.
• Do not attempt to service this apparatus yourself.
• Do not place a glass of water on the product.
• Do not install near any magnetic sources.
• Do not block any ventilation openings.
• Do not place heavy items on the product.
• Please wear protective gloves when installing/removing the camera. The high temperature of the product surface may cause a burn.

User's Manual is a guidance book for how to use the products.

The meaning of the symbols are shown below.

• Reference: In case of providing information for helping of product's usages
• Notice: If there's any possibility to occur any damages for the goods and human caused by not following the instruction
  ※ Please read this manual for the safety before using of goods and keep it in the safe place.

contentS

OVERVIEW	3 Important Safety Instructions6 Recommended PC Specifications6 Recommended Micro SD/SDHC/SDXC Memory Card Specifications6 NAS recommended specs
OUTDOOR VANDAL DOME	8 What's Included8 At a Glance9 Installation
INDOOR VANDAL DOME	17 What's Included17 At a Glance18 Installation
FLUSH MOUNT DOME	25 What's Included25 At a Glance26 Installation
INSTALLATION & CONNECTION	32 Optional Accessories for Installation34 Connecting with other Device

NETWORK CONNECTION AND
SETUP

38

38 Connecting the Camera Directly to Local Area Networking

38 Connecting the Camera Directly to a DHCP Based DSL/Cable Modem

39 Buttons used in IP Installer

39 Static IP Setup

41 Dynamic IP Setup

41 Port Range Forward (Port Mapping) Setup

42 Connecting to the Camera from a Shared Local PC

42 Connecting to the Camera from a Remote PC via the Internet

WEB VIEWER

43

43 Connecting to the Camera

44 Password setting

44 Login

44 Camera Web Viewer Setup

APPENDIX

45

45 Specification

51 Product Overview

52 Troubleshooting

54 Open Source Announcement

overview

recommenDeD pc SpecificationS

• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher
• RAM : 8G or higher
• Supported OS : MS Windows, Mac OS X
• Recommended browser: Google Chrome
Supported browsers: MS Explorer, MS Edge, Mozilla Firefox (Window 64bit only), Apple Safari (Mac OSX only)
※ Please see the appendix for detailed information on verified OS and browsers.

recommenDeD micro SD/SDHc/SDXc memory carD SpecificationS

• Recommended capacity : 16GB to 256GB (MLC type)
- The following types of memory cards from the following manufacturers are recommended for this camera.
- Manufacturer : SanDisk, Transcend
- Product family : High endurance

naS recommenDeD SpecS

• Recommended capacity: 200GB or higher is recommended.
• Simultaneous access: One unit of NAS can accept a maximum of sixteen camera accesses.
• For this camera, you are recommended to use a NAS with the following manufacturer's specs.

Recommended products Available sizes

GNAP NAS A maximum of 16 cameras can access simultaneously.

Synology NAS A maximum of 16 cameras can access simultaneously.

■ If you use NAS equipment for purposes other than video saving, the number of accessible cameras may be reduced.

Outdoor Vandal DomeXNV-6081/XNV-6081R/XNV-8081R

Indoor Vandal DomeXND-6081V/XND-6081RV/XND-8081RV

Flush Mount DomeXND-6081F/XND-6081RF/XND-8081RF

WHAT'S INCLUDED

As for each sales country, accessories are not the same.

Technical line drawing of a mechanical component with a central dome and flange (no text or symbols)

Color: Ivory

Option (sold separately)

8_ outdoor vandal dome

AT A GLANCE

INSTALLATION

This camera is waterproof and in compliance with the IP67/IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• Select an installation site that can hold at least 5 times the camera's weight.
• Stuck-in or peeled-off cables can cause damage to the product or a fire.
• For safety purposes, keep anyone else away from the installation site.
  And put aside personal belongings from the site, just in case.
• If the product is installed with excessive force, it may cause damage to the camera due to malfunction. Forcing assembly using non-compliant tools may damage the product.

Removal

1. Peel off the tape fixing the camera case.

Illustration of hands operating a device with a lid and handle, showing internal components (no text or symbols)

1. Take off the cushion protecting the camera lens.

Line drawing of a mechanical device with a hand adjusting a component (no text or symbols visible)

Inserting a Micro SD Memory Card

Slide the Micro SD card into the Micro SD slot on the camera module in the direction of the arrow.

Before installing the camera, the Micro SD memory card should be inserted while the power source and the body are separated.
- Do not forcefully insert it in the reverse direction. It might damage your Micro SD memory card and your product.
- When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.
- When installing/removing the Micro SD memory card, make sure you cut the product body on a flat ground before working on it in order to prevent accidents due to loss or drop of any parts.

outdoor vandal dome

Removing a Micro SD Memory Card

Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.

• Please note that if you firmly push and release the Micro SD memory card when it is ejected, it may pop out.
  Before removing the Micro SD memory card, in , set the device to and press the [Apply] button and turn the camera off.
• If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or damaged.

Installing the AC module (sold separately: SPC-100AC)

1. Install the AC module as shown in the figure.
2. Tighten the screw using the hex key.

Installation (mount plate)

[Directly installing on wall/ceiling]

1-1. Attach the installation template on the desired surface and drill holes for screws and cables.

Technical line drawing of a mechanical assembly with concentric circles and a tool, no text or symbols present

1-2. Fix the mount plate using appropriate screws.
1-3. Pull out necessary cables among LAN/power/audio & alarm cables through the hole in the mount plate.

[Installing using pipe]

2-1. Attach the installation template and drill holes for screws and cables.

2-2. Separate the pipe cover of the mount plate by pressing its sides.

outdoor vandal dome

2-3. Place the pipe on the mount plate.
2-4. Fix the mount plate using appropriate screws.
2-5. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe.

Installation (camera case)

- Use a cable bush compliant with the LAN cable to be connected.

- Camera main: use a cable with the diameter of 25 to 6.5

-Components: use a cable with the diameter of 25 to 8.5

[Installing LAN/power cables]

1-1. Pull off the extruded parts of the bush to be used.
1-2. Route the LAN cable through the big hole of the bush and connect to the LAN connector.
1-3. (When using the power) Route the power cable through the small hole of the bush and connect it to the provided terminal block.

1-4. Mount the bush to the camera case.

Technical line drawing of two circular mechanical components with internal components and wiring (no text or symbols)

[Installing the LAN cable] (IP66)

2-1. Pull off the extruded part of the 1-hole bush provided.
2-2. Use the cap installer to pass through the RJ45 cable.

Cap Installer

Four diagrams showing mechanical assembly steps with arrows indicating motion (no text or symbols)

12_ outdoor vandal dome

2-3. Mount the bush to the camera case.

Technical line drawing of a mechanical assembly with internal components (no text or symbols)

1. Join the mount plate with the camera case.
   

[Installing audio & alarm cables]
3-1. Mount the bush of the provided audio & alarm cables to the camera case.

Technical line drawing of a mechanical assembly with exploded view and close-up detail (no text or symbols)

outdoor vandal dome

Installing the camera module

1. Connect the LAN/power/audio & alarm cables to the camera module terminal.
2. Attach the camera module to the case.

- A magnet is embedded at the bottom of the module - Take caution not to allow any foreign objects between the attaching surfaces.

1. Adjust the lens to the desired direction with reference to "Adjusting the monitoring direction for the camera" section. (page 33)

Assembling the dome cover

[Directly installing on wall/ceiling]

1. Assemble the dome cover.

■ Make sure to firmly tighten the fastening screws so that there is no water damage issue.
- Be careful when using the AC module as the dome cover has a certain working direction.

• Be careful not to alter the monitoring direction of your camera.

14 outdoor vandal dome

[Using Weather cap]

1. Remove the screws from the dome cover.

1. Assemble the dome cover.
2. Mount the weather cap to the dome cover and fasten the screws.

- Make sure to firmly tighten the fastening screws so that there is no water damage issue.

Using/Removing Skin cover

1. Put on the skin cover in alignment with the pipe cover.

Technical line drawing of two mechanical components with a directional arrow indicating assembly or motion (no text or symbols present)

1. For a camera connected with a pipe, remove the pipe cover from the skin cover first before putting it on.

Technical illustration of two mechanical components with a magnified inset showing a tool interacting with the ring (no text or symbols present)

outdoor vandal dome

1. To remove the skin cover, pull it while turning it clockwise as shown in the figure.

- Repetitive installation and removal of the skin cover may deform the skin cover. - Installation and removal of the skin cover with excessive force may cause scratches on the surface of the product.

Diagram of a mechanical component with rotational arrows indicating motion (no text or symbols)

- When place is connected, release it using an appropriate tool.

Diagram of a mechanical component with a magnified inset showing a hand holding a curved blade (no text or symbols present)

Outdoor installation

When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside.

1. Connect the power, I/O, and LAN cables.

2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.

- If the cable jacket is not waterproofed properly, then it can directly cause leakage. Make sure to protect the cable with a dense layer of taping. - Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.

16_ outdoor vandal dome

WHAT'S INCLUDED

As for each sales country, accessories are not the same.

Technical line drawing of a mechanical component with a spherical top and concentric rings (no text or symbols)

Color: Ivory

Option (sold separately)

AT A GLANCE

INSTALLATION

This camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• Select an installation site that can hold at least 5 times the camera's weight.
• Stuck-in or peeled-off cables can cause damage to the product or a fire.
• For safety purposes, keep anyone else away from the installation site.
  And put aside personal belongings from the site, just in case.
• If the product is installed with excessive force, it may cause damage to the camera due to malfunction. Forcing assembly using non-compliant tools may damage the product.

Removal

1. Peel off the tape fixing the camera case.

Illustration of hands assembling a mechanical component with arrows indicating assembly direction (no text or symbols)

1. Take off the cushion protecting the camera lens.

Line drawing of a hand turning a mechanical component with no visible text or symbols

Inserting a Micro SD Memory Card

Slide the Micro SD card into the Micro SD slot on the camera module in the direction of the arrow.

Before installing the camera, the Micro SD memory card should be inserted while the power source and the body are separated.
- Do not forcefully insert it in the reverse direction. It might damage your Micro SD memory card and your product.
- When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.
- When installing/removing the Micro SD memory card, make sure you cut the product body on a flat ground before working on it in order to prevent accidents due to loss or drop of any parts.

Removing a Micro SD Memory Card

Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.

• Please note that if you firmly push and release the Micro SD memory card when it is ejected, it may pop out.
  Before removing the Micro SD memory card, in , set the device to and press the [Apply] button and turn the camera off.
• If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or damaged.

Installation (mount plate)

[Directly installing on wall/ceiling]

1-1. Attach the installation template on the desired surface and drill holes for screws and cables.

1-2. Fix the mount plate using appropriate screws.
1-3. Pull out necessary cables among LAN/power/audio & alarm cables through the hole in the mount plate.

incoor vandal dome

[Installing using pipe]

2-1. Attach the installation template and drill holes for screws and cables.

2-2. Separate the pipe cover of the mount plate by pressing its sides.

2-3. Place the pipe on the mount plate.
2-4. Fix the mount plate using appropriate screws.
2-5. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe.

Installation (camera case)

- Use a cable bush compliant with the LAN cable to be connected.

-Camera main: use a cable with the diameter of 95 to 6.5

-Components: use a cable with the diameter of 85 to 8.5

[Installing LAN/power cables]

1-1. Pull off the extruded parts of the bush to be used.
1-2. Route the LAN cable through the big hole of the bush and connect to the LAN connector.
1-3. (When using the power) Route the power cable through the small hole of the bush and connect it to the provided terminal block.

1-4. Mount the bush to the camera case.

Technical line drawing of a mechanical assembly with internal components (no text or symbols)

2-3. Mount the bush to the camera case.

Technical line drawing of a mechanical assembly with internal components (no text or symbols)

[Installing the LAN cable]

2-1. Pull off the extruded part of the 1-hole bush provided.
2-2. Use the cap installer to pass through the RJ45 cable.

Cap Installer

Four technical diagrams showing mechanical assembly steps with arrows indicating motion (no text or symbols)

incoor vandal dome

[Installing audio & alarm cables]

3-1. Mount the bush of the provided audio & alarm cables to the camera case.

Technical line drawing of a device interior with exploded view and close-up detail (no text or symbols)

1. Join the mount plate with the camera case.

22_ indoor vandal dome

Installing the camera module

1. Connect the LAN/power/audio & alarm cables to the camera module terminal.
2. Attach the camera module to the case.

- A magnet is embedded at the bottom of the module - Take caution not to allow any foreign objects between the attaching surfaces.

1. Connect the microphone cable to the camera module.

1. Adjust the lens to the desired direction with reference to "Adjusting the monitoring direction for the camera" section. (page 33)

Assembling the dome cover

[Directly installing on wall/ceiling]

1. Assemble the dome cover.

- Make sure to firmly tighten the fastening screws so that there is no water damage issue.

- Be careful not to alter the monitoring direction of your camera.

Using/Removing Skin cover

1. Put on the skin cover in alignment with the pipe cover.

Technical line drawing of two mechanical components with a directional arrow indicating assembly or transformation (no text or symbols present)

1. For a camera connected with a pipe, remove the pipe cover from the skin cover first before putting it on.

Technical line drawing of two mechanical components with a magnified inset showing a tool interacting with the ring (no text or symbols present)

incoor vandal dome

1. To remove the skin cover, pull it while turning it clockwise as shown in the figure.

- Repetitive installation and removal of the skin cover may deform the skin cover. - Installation and removal of the skin cover with excessive force may cause scratches on the surface of the product.

Diagram of a mechanical component with rotational arrows indicating motion (no text or symbols)

- When place is connected, release it using an appropriate tool.

Diagram of a mechanical component with a magnified inset showing a hand holding a curved blade (no text or symbols)

Outdoor installation

When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside.

1. Connect the power, I/O, and LAN cables.

2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.

- If the cable jacket is not waterproofed properly, then it can directly cause leakage. Make sure to protect the cable with a dense layer of taping. - Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.

24_ indoor vandal dome

flush mount come

WHAT'S INCLUDED

As for each sales country, accessories are not the same.

Technical line drawing of a circular mechanical component with a central dome and mounting brackets (no text or symbols)

Collection of various electronic components and connectors, including a dome-shaped device, camera, grid, and various switchgear (no text or labels visible)

AT A GLANCE

INSTALLATION

This camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• Select an installation site that can hold at least 5 times the camera's weight.
• Stuck-in or peeled-off cables can cause damage to the product or a fire.
• For safety purposes, keep anyone else away from the installation site.
  And put aside personal belongings from the site, just in case.
• If the product is installed with excessive force, it may cause damage to the camera due to malfunction. Forcing assembly using non-compliant tools may damage the product.

Removal

1. Peel off the tape fixing the camera case.

Technical illustration showing hands operating a mechanical component with directional arrows indicating motion (no text or symbols present)

26_ flush mount dome

1. Take off the cushion protecting the camera lens.

Line drawing of a hand turning a mechanical component with no visible text or symbols

Inserting a Micro SD Memory Card

Slide the Micro SD card into the Micro SD slot on the camera module in the direction of the arrow.

Before installing the camera, the Micro SD memory card should be inserted while the power source and the body are separated.
- Do not forcefully insert it in the reverse direction. It might damage your Micro SD memory card and your product.
- When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.
- When installing/removing the Micro SD memory card, make sure you cut the product body on a flat ground before working on it in order to prevent accidents due to loss or drop of any parts.

Removing a Micro SD Memory Card

Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.

• Please note that if you firmly push and release the Micro SD memory card when it is ejected, it may pop out.
  Before removing the Micro SD memory card, in , set the device to and press the [Apply] button and turn the camera off.
• If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or damaged.

Installation (housing)

1. Attach the installation template to the ceiling and mark its location with a pencil.

Diagram showing a 3D object with an arrow pointing upward and a pencil inserted, no text or symbols present.

1. Attach the installation template and drill holes.

Line drawing of a saw cutting through a circular opening on a square base (no text or symbols)

flush mount come

1. Connect the safety cable.

- A safety cable is not provided.

e.g

Technical line drawing of a mechanical assembly with no visible text or symbols

Technical line drawing of a mechanical assembly with no visible text or symbols

[Using pipe]

4-1. Install the pipe in a fitting hole.

4-2. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe.

Technical line drawing of a mechanical assembly with a circular component and a hexagonal base (no text or symbols)

28_ flush mount dome

Installation (camera case)

- Use a cable bush compliant with the LAN cable to be connected.

-Components: use a cable with the diameter of 25 to 8.5

[Installing LAN/power cables]

1-1. Pull off the extruded parts of the bush to be used.
1-2. Route the LAN cable through the big hole of the bush and connect to the LAN connector.
1-3. (When using the power) Route the power cable through the small hole of the bush and connect it to the provided terminal block.

1-4. Mount the bush to the housing.

Technical line drawing of a mechanical component with no visible text or symbols

[Installing the LAN cable]

2-1. Pull off the extruded part of the 1-hole bush provided.
2-2. Use the cap installer to pass through the RJ45 cable.

2-3. Mount the bush to the housing.

Technical line drawing of a mechanical housing component with mounting flanges and internal components (no text or symbols)

flush mount come

[Installing audio & alarm cables]

3-1. Mount the bush of the provided audio & alarm cables to the camera case.

Technical line drawing of a mechanical assembly with no visible text or symbols

1. Turn the screws on the housing to fix the housing to the ceiling.

The bracket will fix the housing to the ceiling.

■ Ensure that the housing is firmly fixed to the ceiling.

graph TD
    A["Top Component"] --> B["Intermediate Component"]
    B --> C["Bottom Component"]
    C --> D["Bottom Bracket"]
    D --> E["2x Tr20 Icon"]
    style A fill:#f9f,stroke:#333
    style B fill:#f9f,stroke:#333
    style C fill:#f9f,stroke:#333
    style D fill:#f9f,stroke:#333
    style E fill:#ccf,stroke:#333

30_ flush mount dome

Installing the camera module

1. Connect the LAN/power/audio & alarm cables to the camera module terminal.
2. Attach the camera module to the case.

A magnet is embedded at the bottom of the module
Take caution not to allow any foreign objects between the attaching surfaces.

1. Adjust the lens to the desired direction with reference to "Adjusting the monitoring direction for the camera" section, (page 33)

Assembling the dome cover

1. Assemble the dome cover.

- Make sure to firmly tighten the fastening screws so that there is no water damage issue.

- Be careful not to alter the monitoring direction of your camera.

Outdoor installation

When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside.

1. Connect the power, I/O, and LAN cables.

2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.

If the cable jacket is not waterproofed properly, then it can directly cause leakage. Make sure to protect the cable with a dense layer of taping.
- Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.

installation & connection

optionalL acceSSorieS for inStaLLation

	Hanging mount Hanging mount
Model Name SBP-10/HMW SBP-16/HMW
Compatible model XW-6081/XNW-6091R/XW-8081R XND-6081W/XND-8081RW/XND-8081RV
	Wall mount Ceiling mount
Model Name SBP-300WMW1 SBP-300CMW
Compatible model SBP-180HMW/160HMW SBP-180HMW/180HMW
	Corner mount Pole mount
Model Name SBP 300KMW SBP-300PMW
Compatible model SBP-300WMW1 SBP-300WMW1

	Skin cover	Skin cover
Model Name	SEC-130B (Black)	SEC-160B (Black)
Compatible model XW-6081/XNV-6081R/XNV-8081R XND-6081V/XND-6081RW/XND-8081RV
	AC24V power module
Model Name	SPC-10CAC
Compatible model	XNW-6081/XNV-6081R/XNV-8081R

Adjusting the monitoring direction for the camera

▪ Adjusting the monitoring direction

You can adjust the camera direction only when the camera is fixed on the ceiling.

At this time, rotating the main body of the camera in the left and right direction is called PAN, and adjusting the angle of the camera is called TILT.

- The pan angle is 0^-360^

• The tilt angle is -45° - 85°.
• The rotation angle is 0^-355^ .

In 75' or more tilt angle, a blockage of view or burned image may occur in some part of the screen depending on the zoom magnification.

- Do not forcefully rotate or press the focus/zoom lens. Otherwise, the focus might not work properly due to motor failure.

■ Methods of adjustment

1. Adjust the pan angle taking account of the direction to monitor.
2. Adjust the horizontal angle so that the video does not flip when rotated.
3. Adjust the tilt angle toward the direction to monitor.

Adjust the direction of IR LEDs not to hinder their view by an instrument.

Adjust the direction of IR LEDs not to hinder their view by a weather cap (if any).

CONNECTING WITH OTHER DEVICE

The CVBS out terminal of the product is provided for easier installation, and is not recommended for monitoring purposes.

- The Micro USB out terminal of the product is provided for easier installation, and is not recommended for monitoring purposes.

Ethernet Connection

Connect the Ethernet cable to the local network or to the Internet.

Connecting WiFi

Camera Setup

1. Connect OTG adapter (5-pin) and WiFi dongle to the micro USB terminal.

Smartphone Setup

1. Install the Wisenet installation application.
2. Select the camera SSID after turning on the WiFi.
3. Run the Wisenet Installation application.
4. When you log in to the camera, the video will be connected.

- The video will be played without being logged in during the initial connection.

1. You can adjust angle of view while watching the video through smartphone.

Recommended dongle manufacturer

Manufacturer Model
NETIS WF2123 n300
EDIMAX FW-7811Un
IP Time N100mini
TP-LINK TL-WN823N V1
ASUS USB-N13
NETGEAR WNA3100M

Power Supply

Use the screwdriver to connect each line (+, -) of the power cable to the corresponding power port of the camera.

- If the power sources for PoE and DC 12 V are simultaneously turned on, the device power will be supplied by both of PoE and DC 12 V.

- You can also use a router featuring PoE to supply power to the camera.

- Use PoE that is compliant with the IEEE 802.3af protocols.

- Be careful not to reverse the polarity when you connect the power cable.

The AC power is available after purchasing an AC module (SPC-100AC).

- Models: XNV-6081/XNV-6081R/XNV-8081R

- If the power sources for PoE and AC 24V are simultaneously turned on, the external power source (AC 24V) will be used.

- AC 24 V can be connected as non-polar.

- If you want to connect an external device, you must turn off the external device before proceeding.

- Connect the set and the adapter power line first, and then connect the power cable to the outlet on the wall.

Power Cable Specification for Each Model

Model Input power: Wire Type (AWG) Cable Length (Max.)
XND-6081VFXND-6081RWRF	DC 12V	#18 22m
		#20 14m
XND-9081RWRF DC 12V		#18 20m
		#20 13m
XWV-6081/6081R	DC 12V	#18 22m
		#20 14m
	AC 24V	#18 40m
		#20 26m
XWV-9081R	DC 12V	#18 20m
		#20 13m
	AC 24V	#18 38m
		#20 24m

Network Cable Specification

Item Contents Remark
Connector RJ45 (10/100BASE-T)
Ethernet	10/100BASE-T
Cable	UTP Category 5c
Max Distance	100M
PoE Support	IEEE 802.3af

Connecting to Audio Input/Output

graph TD
    A["Speaker"] --> B["Switch"]
    C["Speaker"] --> B
    D["Speaker"] --> B
    E["Microphone"] --> F["Network"]
    G["Microphone"] --> F
    H["Microphone"] --> F
    I["PC"] --> F
    F --> J["Speaker"]
    F --> K["Microphone"]

1. Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of the amplifier that the microphone is connected to.

- You can use the internal microphone of the camera without an external microphone connection (only applicable for XND-6081V/XND-6081RV/XND-8081RV).

1. Connect the AUDIO OUT port of the camera with the speaker or LINE IN port of the amplifier that the speaker is connected to.

2. Check the specifications for audio input.

installation & connection

- Audio Codec

• Audio In : G.711 PCM (Bit Rate: 64Kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate: 16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz), AAC (Bit Rate: 48Kbps / Sampling Frequency: 16kHz)
• Audio Out : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz)

- Full duplex Audio

• Audio in (XND-6081V/XND-6081RV/XND-8081RV) : Selectable (microphone/Line-in/Built-in microphone). Supported voltage: 2.5VDC (4mA), Input impedance: 2K Ohm
• Audio in (XND-6081F/XND-6081RF/XND-8081RF/XNV-6081/XNV-6081R/XNV-8081R) : Selectable (microphone/Line-in), Supported voltage: 2.5VDC (4mA), Input impedance: 2K Ohm
  • Audio out : Line-out (3.5mm mono jack), Maximum output: 1Vms
  • Line out impedance : 600Ω

In the case you access the web viewer and select an external microphone as the audio input sources in

-Frequency range: 40-16,000 Hz
-Impedance: 1,500 Ω
-Sensitivity: -40±3 dB (7.1-14.1 mV)

In any of the following cases, sound classification performance may be degraded or malfunction:

-If gunshot sounds are heard continuously in a short interval (e.g. machine gun sound) rather than a one-time gunshot sound
-If the noise is too loud for the noise and the target sound to be distinguished
-If two or more of different sounds are registered simultaneously
-If the sound classification is applied while using the noise removal function in a quiet place
- If the source of clapping sounds or screams is close to the camera (within 1 meter)
-If a sound that does not belong to any of the sound classification categories (airplanes sound, siren sound, etc.) is loudly heard all of sudden
-If external microphone does not meet the recommended specifications

Connecting to the I/O port box

Connect the Alarm I/O cable to the corresponding port of the port box.

• ALARM-IN : Used to connect the alarm input sensor.
• ALARM-OUT : Used to connect the alarm output signal.
• GND : Common port for alarm in/output signal.

If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open collector method, it may cause malfunction. Refer to the "Alarm Out Wiring Diagram" when connecting devices that exceed the voltage and current specifications. (page 37)

To connect the external sensor

Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port, and connect the other strand to the [GND] port.

Alarm In Wiring Diagram

Alarm Out Wiring Diagram

network connection and setup

You can set up the network settings according to your network configurations.

CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING

Connecting to the camera from a local PC in the LAN

1. Launch an internet browser on the local PC.
2. Enter the IP address of the camera in the address bar of the browser.

graph TD
    A["Local PC"] --> B["Switch"]
    C["Switch"] --> B
    D["External Remote PC"] --> E["DOS Server\nLocal Center, RDFER"]
    B --> F["IOH-EM"]
    E --> F

A remote PC in an external Internet out of the LAN network may not be able to connect to the camera installed in the intranet if the port-forwarding is not properly set or a firewall is set.
In this case, to resolve the problem, contact your network administrator.
- In the IP installer, you can use the initial password, "4321" to set IP Address, Subnot Mask, Gateway, HTTP Port, VWP Port, IP type. After changing the network interface, for better security, access the web viewer and change the password.
- By factory default, the IP address will be assigned from the DHCP server automatically if there is no DHCP server available, the IP address will be set to 192.168.1.100. To change the IP address, use the IP Installer. For further details on IP Installer use, refer to "Static IP Setup". (Page 39)

CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM

graph LR
    A["Camera"] --> B["COLV/Video Module"]
    B --> C["PC"]
    C --> D["External Remote PC"]
    C --> E["DB/MS Server (Data Center, H/O 32V)"]

1. Connect the user PC directly with the network camera.
2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on your desktop to connect to the Internet.
3. Use the Internet browser to connect to the web viewer.
4. Move to [Setup] page.
5. Move to [Network] - [DDNS] and configure the DDNS settings.
6. Move to [Basic] - [IP & Port], and set the IP type to [DHCP].
7. Connect the camera, which was removed from your PC, directly to the modem.
8. Restart the camera.

- For information on how to set DONS, refer to the online help of Web Viewer. - For information on how to set the IP format, refer to the online help of Web Viewer.

BUTTONS USED IN IP INSTALLER

a b c d e f g

hi jk lm

Item Description

a	Device Name	Model name of the connected camera.Click the column to sort the list by model name.However, search will be stopped if clicked during the search.
b	Alias	This function is not currently implemented.
c	Mode	Displays eitherorfor the current network connection status.
d	MAC(Ethernet) Address	Ethernet address for the connected camera.Click the column to sort the list by Ethernet address.However, search will be stopped if clicked during the search.
e	IP Address	IP address.Click the column to sort the list by IP address.However, search will be stopped if clicked during the search.
f	Protocol	Network setting for the camera.The factory default is "IPv4".Cameras with the IPv6 setting will be displayed "IPv6".
g	URL	DDNS URL address enabling access from the external Internet.However, this will be replaced with theof the camera if DDNS registration has failed.
h	IPv4	Scans for cameras with the IPv4 setting.

Item Description

i	IPv6	Scans for cameras with the IPv6 setting. Activated in an IPv6 compliant environment only.
j	Search	Scans for cameras that are currently connected to the network. However, this button will be grayed out if neither IPv4 nor IPv6 is checked.
k	Auto Set	The IP Installer automatically configures the network settings.
l	Manual Set	You should configure the network settings manually.
m	Exit	Exits the IP Installer program.

Use the latest version of the IP installer. You can download the latest version from the Hanwha Techwin web site.

- If the supporting OS is Windows 8.1, it is recommended that you use the Wisenet Device Manager instead of the IP Wisenet. The Wisenet Device Manager Program can be downloaded by visiting the Hanwha Techwin website (http://www.hanwha-security.com) under the menu - .

STATIC IP SETUP

Manual Network Setup

Run to display the camera search list.

At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.

For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not support this function.

1. Select a camera in the search list. Check the MAC address of the camera on the camera's label. Both the [Auto Set] and [Manual Set] buttons will be activated.
2. Click [Manual Set]. The Manual Setting dialog appears. , , , , and of the camera are displayed in the preset values.
3. In the
   pane, provide the necessary information.
4. MAC (Ethernet) Address : The MAC address imprinted on the camera label is automatically displayed and requires no user setting.
   IP related parameters can be set only when DHCP is not checked.

network connection and setup

If not using a Broadband Router

For setting , , and , contact your network administrator.

1. In the pane, provide necessary information.

2. HTTP Port: Used to access the camera using the Internet browser, defaulted to 80.
   • VNP Port : Used to control the video signal transfer, defaulted to 4520.

3. Enter the password.

Enter the password of "admin" account, which was used to access the camera.

For the security purposes, you are recommended to use a combination of numbers, alphabets uppercase and lowercase and special characters for your password.

- For information on how to change the password, refer to the online help of Web Viewer.

1. Click [OK]

Manual network setup will be completed.

If using a Broadband Router

- IP Address : Enter an address falling in the IP range provided by the Broadband Router.

exj 192.168.1.2-254, 192.168.0.2-254, 192.168.XXX.2-254

- Subnet Mask: The of the Broadband Router will be the of the camera.

- Gateway: The of the Broadband Router will be the of the camera.

The settings may differ depending on the connected Broadband Router model.

For more information, refer to the user manual of the applicable router.

- For more information about port forwarding of the broadband router, refer to "Port Range Forward (Port Mapping) Setup". (Pages 41)

If the Broadband Router has more than one camera connected

Configure the IP related settings and the Port related settings distinctly with each other.

exj

Category Camera #1 Camera #2
IP related settings	IP Address	192.168.1.100	192.168.1.101
	Subnet Mask	255.255.255.0	255.255.255.0
	Gateway	192.168.1.1	192.168.1.1
Port related settings	HTTP Port	8000	8081
	VNP Port	4520	4521

If the is set other than 80, you must provide the number in the address bar of the Internet browser before you can access the camera.

exi. http://AP address : HTTP Port

http://192.168.1.100:8080

Auto Network Setup

Run to display the camera search list.

At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.

For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not support this function.

1. Select a camera in the search list. Check the MAC address of the camera on the camera's label. Both the [Auto Set] and [Manual Set] buttons will be activated.

2. Click [Auto Set]. The Auto Setting dialog appears. The , , and will be set automatically.

3. Enter the password. Enter the password of "admin" account, which was used to access the camera.

- For the security purposes, you are recommended to use a combination of numbers, alphabels uppercase and lowercase and special characters for your password.

- For information on how to change the password, refer to the online help of Web Viewer.

1. Click [OK]. Auto network setup will be completed.

DYNAMIC IP SETUP

Dynamic IP Environment Setup

• Example of the Dynamic IP environment

- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server

- If connecting the camera directly to modem using the DHCP protocols

- If IPs are assigned by the internal DHCP server via the LAN

Checking the Dynamic IP

1. Run the IP Installer on the user's local computer. Cameras allocated with address are shown in the list.

2. Select a camera from the search result.

3. Click the [Manual Set] button and check the camera's address. If you uncheck , you can change IP to .

PORT RANGE FORWARD (PORT MAPPING) SETUP

If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it.

Manual Port Range Forwarding

1. From the Setup menu of the Broadband Router, select - . For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router.

2. Select and for each connected camera to the Broadband Router. The number of each port to be configured to the IP router should be set according to the port number designated in - - on the camera web viewer.

1. When done, click [Save Settings]. Your settings will be saved.

- Above sample instructions are based on the CISCO's Broadband Router.

- The settings may differ depending on the connected Broadband Router model. For more information, refer to the user manual of the applicable router.

Setting up Port Range Forward for several network cameras

- You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. - A user can change each port using the camera setting screen.

When Camera1 and Camera2 are connected to a router :

graph TD
    A["User"] <--> B["Internet"]
    B --> C["Broadband Router"]
    C --> D["Camera1 (192.168.1.100)"]
    C --> E["Camera2 (192.168.1.101)"]
    D --> F["HTTP port 8080"]
    D --> G["Device port 4520"]
    D --> H["RTSP port 3000"]
    C --> I["Start End Protocol IP Address"]
    C --> J["3000 3000 TCP/UDP 192.168.1.100"]
    C --> K["3001 3001 TCP/UDP 192.168.1.101"]
    C --> L["4520 4520 TCP/UDP 192.168.1.100"]
    C --> M["4521 4521 TCP/UDP 192.168.1.101"]
    C --> N["8080 8080 TCP/UDP 192.168.1.100"]
    C --> O["8081 8081 TCP/UDP 192.168.1.101"]

- Port forwarding can be done without additional router setup if the router supports the UPnP (Universal Plug and Play) function. After connecting the network camera, select the checkbox from the menu in in *Settings -> Network -> DDNS*.

connectinG to tHe camera from a SHARED LocaL pc

1. Run the IP Installer. It will scan for connected cameras and display them as a list.
2. Double-click a camera to access. The Internet browser starts and connects to the camera.

- Access to the camera can also be gained by typing the camera's IP address in the address bar of the Internet browser.

connectinG to tHe camera from a remote pc via tHe internet

Since using the IP Installer on a remote computer that is not in the Broadband Router's network cluster is not allowed, users can access cameras within a Broadband Router's network by using the camera's DDNS URL.

1. Before you can access a camera in the Broadband Router network, you should have set the port range forward for the Broadband Router.
2. From the remote PC, launch the internet browser and type the DDNS URL address of the camera, or the IP address of the Broadband Router in the address bar. ex) http://ddns.hanwha-security.com/ID

- For information on how to register DDNS, refer to the network setup guide.

CONNECTING TO THE CAMERA

Normally, you would

1. Launch the Internet browser.

2. Type the IP address of the camera in the address bar.

ex) • IP address (IPv4) : 192.168.1.100 →

http://192.168.1.100

- the Login dialog should appear.

- IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111

→ http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear.

If the HTTP port is other than 80

1. Launch the Internet browser.

2. Type the IP address and HTTP port number of the camera in the address bar.

ex) IP address : 192.168.1.100:HTTP Port number(8080)

→ http://192.168.1.100:8060 - the Login dialog should appear.

Using URL

1. Launch the Internet browser.

2. Type the DDNS URL of the camera in the address bar. ex) URL address: http://ddns.henwhe-security.com/ID

- the Login dialog should appear.

■ Network connection is disabled in the LAN only environment.

Connecting via UPnP

1. Run the client or operating system in support of the UPnP protocol.

2. Click the camera name for search.

In the Windows operating system, click the camera name searched from the network menu.

- The login window is displayed.

Connecting via Bonjour

1. Run the client or operating system in support of the Bonjour protocol.
2. Click the camera name for search.

In the Mac operating system, click the camera name searched from the Bonjour tab of Safari.

- The login window is displayed.

To check the DDNS address

If the camera is connected directly to a DHCP-based cable modem or DSL modem, the IP address will change each time it tries to connect to the ISP (the company you subscribed to).

If this is the case, you will not be informed of the IP address changed by DDNS.

Once you register a dynamic IP-based device with the DDNS server, you can easily check the changed IP when you try to access the device.

To register your device to the server, visit http://ddns.hanwha-security.com and register your device first, and then set the Web Viewer's - to , as well as providing

that had been used for DDNS registration.

PASSWORD SETTING

When you access the product for the first time, you must register the login password.

When the "Password change" window appears, enter the new password.

For a new password with 8 to 9 digits, you must use at least 3 of the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned.

-Special characters that are allowed.: \~!@4%^^0_-1=[]/.?/

• For higher security, you are not recommended to repeat the same characters or consecutive keyboard inputs for your passwords.
• If you lost your password, you can press the [RESET] button to initialize the product. So, don't lose your password by using a memo pad or memorizing it.

LOGIN

Whenever you access the camera, the login window appears.

Enter the User ID and password to access the camera.

1. Enter "admin" in the input box. The administrator ID, "admin", is fixed and can not be changed.
2. Enter the password in the input field.
3. Click [OK]. If you have logged in successfully, you will the Live Viewer screen.

- When you access the camera web viewer, pay special attention to the security by checking whether the image data is encrypted.

• If you check the "Remember my credentials" option when your input is done, in future you will be logged in automatically without being prompted to enter the login information.
• You will experience the best video quality if the screen size is 100%. Reducing the ratio may cut the image on the borders.

CAMERA WEB VIEWER SETUP

1. Click the [Setup ( icon.
2. The Settings window appears.
3. You can configure settings for the camera's basic information, video, audio, network, event, analysis, and system over the network.
4. Click to view detailed descriptions of each function.

appendix

Specification

Items		Description
		XNV-6081/XNV-6081R	XND-6081V/XND-6081RV	XND-6081F/XND-6081RF
Video	Imaging Device	1/2.8" 2MP CMOS
	Effective Pixels	1945(H) x 1097(V)
	NETD	None
	Pixel Size	None
	Min. Illumination	XNV 6081/XND-6081V/XND-6081F - Color : 0.015 Lux(F1.4, 1/30sec), B/W : 0.0015 Lux(F1.4, 1/30sec)XNV 6081R/XND 6081RV/XND-6081RF - Color : 0.015 Lux(F1.4, 1/30sec), B/W : 0. Lux(R LED on)
	Video Out	CVBS: 1.0 Vp-p / 75Ω composite, 720x480(N), 720x576(P) for installationUSB : Micro USB type B, 1290x720 for installation
Lens	Focal Length (Zoom Ratio)	2.8~12mm(4.3x) motorized varifocal
	Max. Aperture Ratio	F1.4(Wide) ~ F3.6(Tele)
	Angular Field of View	H : 119.5°(Wide) ~ 27.9°(Tele)V : 62.8°(Wide) ~ 15.7°(Tele)D : 142.1°(Wide) ~ 32.0°(Tele)
	Min. Object Distance	0.5m (1.64ft)
	Focus Control	Simple focus
	Lens Type	DC Auto Iris, P-Iris
	Mount Type	None
	Optional Lens	None

Items		Description
		XNV-6081/XNV-6081R	XND-6081V/XND-6081RV	XND-6081F/XND-6081RF
Pan / Tilt / Rotate	Pan / Tilt / Rotate range	0°-360°/ -45°-85°/ 0°-355°
	Pan Range	None
	Pan Speed	None
	Tilt Range	None
	Tilt Speed	None
	Rotate Range	None
	Sequence	None
	Preset Accuracy	None
	Azimuth	None
	Auto Tracking	None
Operational	IR Viewable Length	XNV-6081/XND-6081V/XND-6081F : NoneXNV-6081R/XND-6081RW/XND-6081RF : 50m(164.04ft)
	Camera Title	Displayed up to 85 characters
	Day & Night	Auto (ICR)
	Backlight Compensation	BLC, HLC, WDR, SSDR
	Wide Dynamic Range	150dB
	Digital Noise Reduction	SSNR V
	Digital Image Stabilization	Support (built-in Cyro Sensor)
	Detog	Support
	Motion Detection	8ea, 8point Polygonal zones

appendix

Items		Description
		XNV-6081/XNV-6081R	XND-6081V/XND-6081RV	XND-6081F/XND-6081RF
Operational	Privacy Masking	32ea, polygonal zones- Color : Gray, Green, Red, Blue, Black, White- Mosaic
	Gain Control	Low / Middle / High
	White Balance	ATW / AWC / Manual / Indoor / Outdoor
	LDC	Support
	Electronic Shutter Speed	Minimum / Maximum / Anti flicker (2 - 1/12,000sec)
	Video Rotation	Flip, Mirror, Hallway view(90°/270°)
	Analytics	Defocus detection. Directional detection, Fog detection. Face detection.Motion detection, Digital auto tracking. Appear/Disappear, Enter/Exit, Loitering,Tampering, Virtual line. Audio detection, Sound classification, Shock detection
	Business Intelligence	People counting, Queue management, Heatmap
	Serial Interface	None
	Alarm I/O	Input 1ea / Output 1ea
	Alarm Triggers	Analytics, Network disconnect, Alarm input
	Alarm events	• File uplced via FIT: E-Mail• Notification via E-Mail• SD/SCHC/SDXC or NAS recording at event triggers• Alarm output• Handover• Audio playback
	Audio In	Selectable (Mic IV/Line IN)Supply voltage:2.5VDC(4mA), InputImpedance: approx. 2KOhm	Selectable (Mic IV/LineIN/Built in mic)Supply voltage:2.5VDC(4mA), InputImpedance: approx. 2KOhm	Selectable (Mic IV/LineIN)Supply voltage:2.5VDC(4mA), InputImpedance: approx. 2KOhm

Items		Description
		XNV-6081/XNV-6081R	XND-6081V/XND-6081RV	XND-6081F/XND-6081RF
Operational	Audio out	Line cut, Max output level: 1 Vrms
	Wiper	None
	Coaxial Protocol	None
	Video Transmission Distance	None
Radiometry	Temperature detect range	None
	Temperature accuracy	None
	Temperature detection	None
	Additional	None
Network	Ethernet	RJ-45 (10/100BASE-T)
	Video Compression	H.265/H.264: Main/Baseline/High, MJPEG
	Resolution	1920x1080, 1280x1024, 1280x360, 1280x720, 1024x768, 800x600, 800x448, 720x576, 720x480, 640x480, 640x360, 320x240
	Max. Framerate	H.265/H.264: Max. 60fps/50fps(60Hz/50Hz) MJPEG: Max. 30fps/25fps(60Hz/50Hz)
	Smart Codec	Manual(Sea area), WisoStream II
	Bitrate Control	H.264/H.265 : CBR or VBR MJPEG : VBR
	Streaming	Unicast(20 users) / Multicast Multiple streaming(Up to 10 profiles)
	Audio Compression	G.711 μ-law/G.726 Selectable G.726 (ADPCM) 8KHz, G.711 8KHz G.726 : 16kbps, 24Kbps, 32Kbps, 40Kbps AAC-LC : 48Kbps at 16KHz
Network	Protocol	IPv4, IPv6, TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTCP, RTSP, NTP, HTTP, HTTP, SSL/TLS, DHCP, FTP, SMTP, ICMP, IGMP, SNMPv1/V2c/V3(MB-2), ARP, DNS, DDNS, QoS, PIM SN, UPnP, Bonjour, LLDP
	Security	HTTPS(SSL) Login AuthenticationDigest Login AuthenticationIF Address FilteringUser access Log802.1x Authentication (EAP-TLS, EAP-LEAP)
	Edge Storage	Micro SD/SDHC/SDXC 2slot 512GB
	Application Programming Interface	ONWIF Profile S/G/TSUNAPI(HTTP API);Wissonet Open Platform
	Web Viewer	Supported OS : Windows 7 / 8.1 / 10, MAC OS X 10.10, 10.11, 10.12Recommended Browser : Google ChromeSupported web browsers : MS Explorer11, MS Edge, Mozilla Firefox (Window 64bit only), Apple Safari (Mac OS X only)
	Memory	1024MB RAM, 256MB Flash
Environmental	Operating Temperature / Humidity	-50°C ~ +60°C (-58°F ~ +140°F) /Less than 90% RH* Start up should be done at above -35°C	-25°C ~ 160°C (-13°F ~ +140°F) / Less than 90% RH
	Storage Temperature / Humidity	-50°C ~ +60°C (-58°F ~ +140°F) / Less than 90% RH
	Certification	IP66/IP67, IK10-, NFMA4X	IP52, IK10	IP52, Plenum rate(UL2820)

Items		Description
		XNV-6081/XNV-6081R	XND-6081V/XND-6081RV	XND-6081F/XND-6081RF
Electrical	Input Voltage	PoE|IEEE802.3af, Class3), 24VAC|Optional, 12VDC	PoE|IEEE802.3af, Class3), 12VDC
	Power Consumption	XNV-6081 - PoE: Max 7.0W, typical 4.90W12VDC: Max 5.4W, typical 3.70W24VAC: Max 7.1W, typical 4.90WXNV-6081R - PoE: Max 12.95W, typical 10.30W12VDC: Max 10.8W, typical 8.40W24VAC: Max 13.3W, typical 10.40WXND-6081V/XND-6081F - PoE : Max 7.0W, typical 4.20W12VDC : Max 5.4W, typical 3.10WXND-6081RV/XND-6081RF - PoE: Max 12.95W, typical 9.4W12VDC: Max 10.8W, typical 7.6W
Mechanical	Color / Material	White / Aluminum
	RAL Code	RAL9003
	Product dimensions / weight	XNV-6081 : 180x125mm(7.09x4.92"),1.45kg(3.20 lb)XNV-6081R : 180x125mm(7.09x4.92"),1.75kg(3.86 lb)	180x125mm (6.30x4.92"),1.45kg(3.20 lb)	205x155mm(8.07x6.10"),1.80kg(3.97 lb)

appendix

Items		Description
		XNV-8081R	XND-8081RV	XND-8081RF
Video	Imaging Device	1/1.8" 6MP CMOS
	Effective Pixels	2616(H) x 1976(V)
	NETD	None
	Pixel Size	None
	Min. Illumination	Color : 0.07 Lux(F1.2, 1/30sec)B/W : 0 Lux(R LED on)
	Video Out	CVBS: 1.0 Vp-p / 75Ω composite, 720x480(N), 720x576(P) for installationUSB : Micro USB type B, 1280x720 for installation
Lens	Focal Length (Zoom Ratio)	3.9~9.4mm(2.4x) motorized varifocal
	Max. Aperture Ratio	F1.3
	Angular Field of View	H : 92.1°(Wide) ~ 38.7°(Tele)V : 67.2°(Wide) ~ 29.0°(Tele)D : 119.9°(Wide) ~ 48.6°(Tele)
	Min. Object Distance	0.5m (1.64ft)
	Focus Control	Simple focus
	Lens Type	DC Auto Iris, P-iris
	Mount Type	None
	Optional Lens	None

Items		Description
		XNV-8081R	XND-8081RV	XND-8081RF
Pan / Tilt / Rotate	Pan / Tilt / Rotate range	0^ -360° / -45°-85° / 0°-355°
	Pan Range	None
	Pan Speed	None
	Tilt Range	None
	Tilt Speed	None
	Rotate Range	None
	Sequence	None
	Preset Accuracy	None
	Azimuth	None
	Auto Tracking	None
Operational	IR Vlowable Length	50m(164.04ft)
	Camera Title	Displayed up to 85 characters
	Day & Night	Auto (CR)
	Backlight Compensation	BLC, HLC, WDR, SSDR
	Wide Dynamic Range	120dB
	Digital Noise Reduction	SSNR V
	Digital Image Stabilization	Support (built-in Gyro Sensor)
	Defog	Support
	Motion Detection	8ea. 8point Polygonal zones
Operational	Privacy Masking	32ea, polygonal zones- Color : Gray, Green, Red, Blue, Black, White- Mosaic
	Gain Control	Low / Middle / High
	White Balance	ATW / AWC / Manual / Indoor / Outdoor
	LDC	Support
	Electronic Shutter Speed	Minimum / Maximum / Anti flicker (2 - 1/12,000sec)
	Video Rotation	Flip, Mirror, Hallway view(90°/270°)
	Analytics	Defocus detection, Directional detection, Fog detection. Face detection.Motion detection, Digital auto tracking. Appear/Disappear, Enter/Ealt, Lentering,Tampering, Virtual line, Audio detection, Sound classification, Shock detection
	Business Intelligence	People counting, Queue management, Heatmap
	Serial Interface	None
	Alarm I/O	Input 1ea / Output 1ea
	Alarm Triggers	Analytics, Network disconnect, Alarm input
	Alarm events	• File up/led via FTP: E-Mail• Notification via: E-Mail• SD/SCHC/SDXC or NAS recording at event triggers• Alarm output• Handover• Audio playback
	Audio In	Selectable (Mic IN/Line IN)Supply voltage:2.5VDC(4mA). Inputimpedance: approx. 2KOhm	Selectable (Mic IN/LineIN/Built in mic)Supply voltage:2.5VDC(4mA). Inputimpedance: approx. 2KOhm	Selectable (Mic IN/LineIN)Supply voltage:2.5VDC(4mA). Inputimpedance: approx. 2KOhm

Items		Description
		XNV-8081R	XND-8081RV	XND-8081RF
Operational	Audio out	Line cut, Max output level: 1 Vrms
	Wiper	None
	Coaxial Protocol	None
	Video Transmission Distance	None
Radiometry	Temperature detect range	None
	Temperature accuracy	None
	Temperature detection	None
	Additional	None
Network	Ethernet	RJ-45 (10/100BASE-T)
	Video Compression	H.265/H.264: Main/Baseline/High, MJPEG
	Resolution	2560x1920, 2560x1440, 1920x1080, 1600x1200, 1280x1024, 1280x960, 1280x720, 1024x768, 800x600, 800x448, 720x576, 720x480, 640x480, 640x360, 320x240
	Max. Framerate	H.265/H.264: Max. 30fps/25fps(80Hz/50Hz) MJPEG: Max. 30fps/25fps(60Hz/50Hz)
	Smart Codec	Manual(Sea area), WiseStream II
	Bitrate Control	H.264/H.265 : CBR or VBR MJPEG : VBR
	Streaming	Unicast(20 users) / Multicast Multiple streaming(Up to 10 profiles)
	Audio Compression	G.711 μ-law /G.726 Selectable G.726 (ADPCM) 8KHz, G.711 8KHz G.726 : 16Kbps, 24Kbps, 32Kbps, 40Kbps AAC-IC : 48Kbps at 16KHz

appendix

Items		Description
		XNV-8081R	XND-8081RV	XND-8081RF
Network	Protocol	IPv4, IPv6, TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTCP, RTSP, NTP, HTTP, HTTPS/SSL/TLS, DHCP, FTP, SMTP, ICMP, IGMP, SNMPv1/V2cV3(MB-2), ARP, DNS, DDNS, QoS, PIM SM, LPnP, Bonjour, LLDP
	Security	HTTPS(SSL) Login AuthenticationDigest Login AuthenticationIP Address FilteringUser access Log802.1x Authentication (EAP-TLS, EAP-LEAP)
	Edge Storage	Micro SD/SDHC/SDXC 2slot 512GB
	Application Programming Interface	GWWIF Profile S/G/TSUNAPI(HTTP API);Wilsonet Open Platform
	Web Viewer	Supported OS : Windows 7 / 8.1 / 10, MAC OS X 10.10, 10.11, 10.12Recommended Browser : Google ChromeSupported web browsers : MS Explorer11, MS Edge, Mozilla Firefox (Window 64bit only), Apple Safari (Mac OS X only)
	Memory	1024MB RAM, 256MB Flash
Environmental	Operating Temperature / Humidity	-50°C ~ +60°C (-58°F ~ +140°F) /Less than 90% RH* Start up should be done at above -35°C	-25°C ~ +60°C (-13°F ~ +140°F) / Less than 90% RH
	Storage Temperature / Humidity	-50°C ~ +60°C (-58°F ~ +140°F) / Less than 90% RH
	Certification	IP66/IP67, IK10-, NFMA4X	IP52, IK10	IP52, Plenum rate(UL2820)

Items		Description
		XNV-8081R	XND-8081RV	XND-8081RF
Electrical	Input Voltage	PoE(IEEE802.3af, Class3), 24VAC(Optional), 12VDC	PoE(IEEE802.3af, Class3), 12VDC
	Power Consumption	PoE: Max 12.95W, typical 10.90W12VDC: Max 11.7W, typical 8.90W24VAC: Max 14.9W, typical 11.30W	PoE: Max 12.95W, typical 10.10W12VDC: Max 11.7W, typical 7.90W
Mechanical	Color / Material	White / Aluminum
	RAL Code	RAL9003
	Product dimensions / weight	180x125mm(7.09x4.92') , 1.75kg(3.86 lb)	160x125mm(5.30x4.92') , 1.45kg(3.20 lb)	205x155mm(8.07x6.10') , 1.90kg(3.97 lb)

proDuct overview

Xnv-6081/Xnv-6081r/Xnv-8081r

Unit : mm (inch)

XnD-6081v/XnD-6081rv/XnD-8081rv

Unit : mm (inch)

appendix

XnD-6081f/XnD-6081rf/XnD-8081rf

Unit: mm (inch)

Top-down schematic of a circular mechanical or electrical component with internal components (no text or symbols)

trouBLeSHootinG

PROBLEM SOLUTION
When an Windows 10 user accesses the web viewer through Chrome or Firefox, the sound volume of microphone changes periodically.	This is what happens when microphone driver has been set to Realtek driver.Install the High Definition Audio device (Windows Default Driver) or the third party driver as the microphone driver.
What are the specifications for WAVE files necessary to play audio at the time of an event?	Sampling rate of 48,000 KHz or less is recommended.For bits per sample (bps), up to 8/16 bit is recommended.Only PCM encoding format is supported.
No video is displayed when accessing the plug-in free webviewer on Safari via HTTPS.	On the authentication popup window prompted when initially accessing https, click "View Authentication Certificate" and select the "Always trust when connecting to the designated webviewer IP" check box.If the webviewer continues failing to display a video after you select "Next" on the message window below, press the command key + Ω to exit the Safari browser, access again and follow the procedures stated above.
I can't access the camera from a web browser.	Check to make sure that the camera's Network settings are appropriate.Check to make sure that all network cables have been connected properly.If connected using DHCP, verify that the camera is able to acquire dynamic IP addresses without any problem.If the camera is connected to a Broadband Router, verify that port forwarding is properly configured.
Viewer got disconnected during monitoring.	Connected Viewers become disconnected upon any change to camera or network configurators.Check all network connections.If the camera is connected over an PPPoF network, it's possible for Viewer to disconnect under poor network conditions.
The camera connected to the network is not detected in the IP installer program.	Turn off the firewall settings on your PC and then search the camera again.
Images overlap.	Check whether two or more cameras are set to a single multicast address instead of different addresses. If a single address is used for multiple cameras, the images may overlap.
No image appears.	• If the transmission method is set to multicast, check whether there is a router that supports multicast in the LAN the camera is connected to.
Voice is not recorded even though audio input settings are configured.	• You must enable thecheck box in-
	• Verify the settings in the following sequence:A. Checksettings.B. Theshould be set to.C. Check if theoption ofmenu is checked to use.
No signal is found at the Alarm Output port oven when an intelligent video analysis event is generated.	• Check alarm output port settings.
Cannot record into the Micro SD memory card.	• Check if the memory card is defective.
Micro SD memory card is inserted but the camera does not operate property.	• Check if the memory card is inserted in the proper direction. Operation of memory card that is formatted by other devices is not guaranteed with this camera unit• Format the memory card again in→→menu.
Cannot record In the NAS.	• Confirm that the information registered in the NAS is correct.
It reports that NAS setting has failed.	• Confirm that the IP address of the NAS is valid.• Confirm that the ID/password of the NAS is valid.• Confirm that you can access the folder designated as the default folder using the ID of the NAS.• Confirm that the NAS SMB/CIFS items are unchecked.• Confirm that the NAS IP address and the camera IP address are in the same format cx) The NAS & camera subnet mask Initial value is 255.255.255.0.If the IP address is 192.168.20.32 then the NAS IP address should be in the range of 192.168.20.1~192.168.20.255.• Check whether you tried to access as another user without formatting the default folder saved or used.• Confirm that you used recommenced NAS equipment.

OPEN SOURCE ANNOUNCEMENT

GPL/LGPL software license

The software included in this product contains copyrighted software that is licensed under the GPLA.GHL. You may explain the complete Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to [e-mail]

If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged.

GPL SW
Component Name License URL

Base Kernel	GPL 2.0
Buybox	GPL 2.0	http://www.com/box.net/sloreneds/snapshots
Envalue-4.3.0	GPL 2.0
Envalue-1.4.51	GPL 2.0	http://enruster.org/pub/index
Envalue-2.3	GPL 2.0
En=1.6.2	GPL 2.0	http://enruster.org/pub/index
En=deg-2.11	GPL 2.0
En=ppsize-2.11	GPL 2.0	http://www.enrgengun.com/ppsize/
Spec_supplant-2.0	GPL 2.0
Sub-4.3.20	GPL 2.0
Subcoon?	GPL 2.0

LGPL SW

Component Name License URL

g lib	LGH 2.0
Installs	LGH 3.0
non 0.256	LGH 2.0 http://www.wccsw.org/mon/

GNU GENERAL PUBLIC LICENSE

Version 2, June 1997

Copyright (C) 1985. 1991 Free Software Foundation, Inc. 51 Franklin Street Fifth Floor, Boston, MA 32110-1301, USA Everyone's permission to copy and distribute verbalim copies of this license document, but changing it is not allowed.

Preamble

The lessons for most software are designed to take away your freedom to share and change it. By contrast, the SQL Closed Public License is intended to require your free room to share end change free software--to make sure the software is free for all its users. The Canadian Public License applies to most of the first Software Foundation's software and to any other program which authors commit to using it; otherwise other Free Software Foundation so ware are swashed by the SQL, I canor General Public License instead. You can apply in the your programs, too. When we speak at these scholars, we are rotating to freeman, not print. Our Canadian Public License also designed to make sure that you have the freedom to distribute access of free software and change for sale. If you know, you can write a free book or a book to get it. If you want it, thus you can arrange the software or use clothes of ill in their free software, then, that you know, you can do these things.

To protect your rights, we need to remove restrictions that forced anyone to deny you, these rights or to ask you to surrender the rights. These res/no one translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute ockles of such a program, whether grate or for e fee, you must give the recipients all the rights that you have

You must make sure that they, too, revoke or can get the source code. And you must show more these forms so they know their rights. We correct your rights win two steps:

(To copyright the software, and 2) offer you the license which gives you legal permission to copy distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If this software is modified by someone else and passed on, we want its recipients to know that what they have is act as original, so that any problems introduced by others will not reflect on the original authors' regulations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistribution of a free program will individually obtain patent licenses. In effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

Version 2, June 1991 Copyright © 1985, 1981 Free Software Foundation, Inc. 51 Franklin S

1. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License.

The "Program", below, refers to any such program or work, and a "work cases on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing no Program or a portion of it, either creation or with modifications and/or translated into another language. In his/her translation is induced without limitation in the term "modification's." From Japanese is addressed as "you".

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not mainstream, and the output from the Program is covered only if its contents constitute a work based on the Program development at having been made by running the Program. Whether that is true depends on what the Program does.

1. You may copy and distribute web form codes of the Program's source code as you receive it, in any medium, provided that you concentrate any appropriately put-out on each copy an appropriate copyright notice and disclaimer of warranty, keep intact at this notice that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of the License along with the Program. You may charge a fee for the principal mail of transferring a copy, and you may of your opinion on offer warranty provision or exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications one or work under the terms of Section 1 above, provided that you also meet all of these conditions.

a) You must cause the modified ties to carry prominent notices stating that you changed the ties and the date of any change

c) You must cause any work that you distribute or publish that in who c or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of the License.

(3) If the modified program normally receives recommends Interactive when run, you must request it, when started running for such interactive use in the most ordinary way to print or display an announcement including an sponsored copyright notice and a notice that there is no warranty for else, saying that you provide a warranty, and that users may redistribute the program under these conditions, and using the user how to view a copy of the License. (4) Accepted the Program itself is Interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.

these requirements apply to the modified work on a whole. It identifies sections of that work are not derived from the Programs, and can be reasonably considered independent and accurate works in the same, then this License and its terms, do not apply to three sections when you distribute them as separate works. But when your distribution the some sections as part or a whole which is a work based on the Programs, the distribution or the whole must be on the terms of this License, whose permissions for other licenses extend to the entire whole, and thus to each and every part regardless or who own it.

Thus, it is not the intent of this section to claim rights or contact your rights to work written entirely by you; rather this intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, there aggregation of another work not based on the Program with the Program for with a work based on the Program in a volume of a storage or distribution medium does not bring the other work under the scope of this license.

1. You may copy and distribute the Program for a work based on it, under Section 2 in object case or deductible form under the terms of Section 1 and 2 above provided that you also do one of the following:

a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

to Accompany it with a written offer, valid for a least three years. * give any third party. In a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange?

6) Accompany it with the information you received so to the offer to distribute corresponding source code. This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form that such an offer, in accord with Subscription (above). The source code for a work means the preferred form of the work for making modifications so it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated Merface definition file, plus the scripts used to correct compilation and installation of the executable. However, as a special exception, the source code distributed cannot include anything that is normally distributed [in other sources or binary terms] with no major

components (compiler, kernel, and so only of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

1. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License.

However, parties who have received copies, or rights, from you under this license will not have their lenders terminated so long as such parties remain in full compliance.

1. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or to derivative works.

These actions are prohibited by law. If you do not accept this License, therefore, by modifying or distributing the Program for any work based on the Program, you indicate your acceptance of this License to do so, and all its norms and conditions for copying, distributing or modifying the Program or works based on it.

1. Each time you redistribute the Program for any work based on the Program, the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this license.

2. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issued), conditions are imposed on you (whether by court order, agreement or otherwise) that contradicts the conditions of this License. They do not excurate you from the conditions of this License if you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pursuant obligations, then as a consequence you may not distribute the Program at all.

For example, if a patent license would not permit royalty interest distribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.

It may portion of this section is held invalid or unenjoyable under any particular circumstance. The balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to ensure you to ignore any parents or other property, right claims or to counter, validity of any such claims. This section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license steadiness. Many people have made generous contributions to the order range of software distribution through this system in reliance on consistent application of their system: it is up to no authorization to decide it as no or she is willing to distribute software through any other system and a license cannot impose that choice. This section is intended to make thoroughly clear what it is called to be a consequence of the rest of this License.

1. If the distribution and/or use of the Program is restricted in several countries either by parents or by copyrighted interfaces, the original copyright holder who closes the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries no, thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

2. The Free Software Foundation may submit revised and/or new versions of the Genera Public License from time to time. Such new versions will be similar in spirit to the present version, but may other in detail to address new problems or concerns. Each version is given a distinguishing version number. The Program specifies a version number of the License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. In the Program does not specify a version number of the License, you may choose any version over published by the Free Software Foundation.

3. If you wish to incorporate parts of the Program into other tree programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

1. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM BASIS WITHOUT WARRANTY OF ANY KIND. EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAMS WITH YOU SHOULD THE PROGRAM/PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVIÇOS, REPAIR OR COHINCION.

2. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO INWRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE US-OR NARITY TO USE THE PROOFAM (NO USING BUT NOT LIMITED TO CLOS OF DATA OR IS A RING ENRICHED INACCULAR OF LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPENITE WITH ANY OTHER PROGRAMS, EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF ITEMS AND CONDITIONS

How to Apply These Terms to Your New Program. If you develop a new program, and you want it to use of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can distribute and change under these terms. To do so, attach the following notices to the program: it is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a porter to where the full notice is found done line to give the program's name and an idea of what does.

Copyright (Gypsy name of author)

This program is free software ; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation : either version 2 or this License, or at your option/any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY: without even the implied warranty of MERCHANTABILITY or HUNES FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program; if not, writes to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02°10-1301, USA.

Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode:

Gromovision version 69. Copyright (C) year name of author Gromovision comes with ABSOLUTELY NO WARRANTY; for details type 'show w'. This is free software and you are welcome to redistribute it under certain conditions; type 'show o' for details.

The hypothetical commands 'show w' and 'show c' should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than 'show w' and 'show c'; they could even be mouse-clicks or menu items-- whatever suits your program.

You should also get your employer if you work as a programmer for your school, if any to sign a "copyright disclaimer" or the program, it necessary. Here is a sample letter for the name:

Yoyodane, Inc., hereby disclaims all copyright interest in the program "Gnomtovson" (which makes passes at complete) written by James Hacker. Signature of Ty Ooon, 1 April 1989, Ty Ooon, President of Vice The General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is Lwthoastn yoeur went to do, use the GNU U.O.O. library General Public instead of this license.

GNU GENERAL PUBLIC LICENSE

Version 3, 29 June 2007

Copyright © 2007 Free Software Foundation, Inc. http://ef.org

Everyone is permitted to copy and distribute verbal copies of this license document, but changing it is not allowed.

Presamble

The GNU General Public License is a free, copyright license for software and other kinds of works. The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change all versions of a program—by making sure licenses free software install its users.

We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its authors.

You can apply it to your programs, too. When we speak of free software, we are retiring to freedom, not price. Our General Public Licensee are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, then you can change the software or use prices of it in new free programs, and that you know you can do these things.

to protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it, responsibilities to respect the freedom of others. For example, if you distribute copies of such a program, whether orders for this fee you must pay on to the residents the same fee/dispos that you received. You must make sure that they too agree

or can get theatureo-oc. And you must show those themselves so they see theirrights. Developers that use the GNU SHI, protect your rights with two steps (1) each onoying on the software, and (2) other you this. License giving you legal permission to copy, distribute and/or modify it. For the developers' and authors'provection, the GPL clearly explains that there is no mandatory for this free software. For both users' and authors' sake, the GPL requires that modified versions be marked as changed, so that their problems will not be attributed errucently to authors of previous versions. Some devices are designed or clear users process to Intel or run modified versions of the software in de-mor, although the manufacturer can do so. This is fundamentally incomprehensive with no film of protecting users' freedom to change the software. The systematic format of such acces occurs in the area of products for in-duals to use, which is precisely where it is less. Inaccurate. Therefore, we have designed this version of the GPL to prevent the practice for these products. If such problems arise in a certain way in other domains, we start rarely to extend this provision to those domains in future versions of the GPL, as required to prove the restriction of users.

Finally, using program is threatened constantly by software patents. States should not allow patents to reorder development and use of software on general purpose computers, but in some that do, we wish to avoid the special anger that parents applied to a free program could make it quietly proprietary. To prevent the GPL assures that stenics cannot be used to render the program non-free. The precise terms and outcomes for copying, distribution and modification follow:

TERMS AND CONDITIONS

1. Definitions.

"This License" refers to version 3 of the GNU General Public License.

Copyright" also means copyright-like laws that apply to other kinds of works, such as semiconductor masks. "The Program" refers to any copyrightable work licenced under the Licensee. Each licenceee is addressed as "you". "Licensees" and "recipients" may be individual or organizations.

To "modify" a work means to copy from or adapt all or part of the work in a fashion, regulating copyright permission, other than the making of an exact copy. The resulting work is called a "modified version" of the earlier work on a work "based on" the earlier work.

A "covered work" means either the unmodified Program or a work based on the Program.

To "protagate" a work means to do anything with it, that, without permission, would make you directly or secondally liable for infringement under applicable copyright law, except executing it on a computer or modifying a private copy.

Propagation includes copying, distribution (with or without modifications), making available to the public, and in some countries other activities as well.

to "approve" a work means any kind of propagation that enables other parties or make or receive copies. More interaction with a user through a computer network, with no transistor of a copy is not convoying. An interactive user interface displays "Appropriate Legal Notices" to the extent that it includes a coworker and prominently visible feature that it displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work except to the extent that warrants are provided, that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user commands or options, such as a menu, a prominent item in the list meets this option.

1. Source Code.

The "source code" for a work means the preferred form at the work for making modifications to it. "Object code" means any non-source form at a work.

A 'Standard Interface' means an interface that other is an official standard defined by a recognized standards body, or in the case of Interface specified for a particular programming language, one that is widely used among developers working in that language.

The "System Ubriare" of an executable work include anything, other than the work as a whole, then (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source case form. A "Major Component", in this context, means a major essential component window system, and so any of the specific operating system (or any on which the executable work runs, or a computer used to produce the work, or an object code interpreter used to run it).

The "Corresponding Sources" for a work in object code form meets all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control three activities.

However, it does not include the works System Libraries, or general-purpose locks or generally available free programs which are used unmodified in performing these activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to require, such as by intimate data communication or control flow between those subprograms and other parts of the work.

The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source. The Corresponding Source for a work in source code form is that same work.

2. Basic Permissions.

All rights granted under this License are granted for the terms of copyright on the Program, and are instantaneous provided related conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content constitutes a covered work. This License acknowledges your rights of an use or other equivalent, as provided by copyright law. You may make, run and coagnate covered works that would do not convert, without conditions so long as your license otherwise remains in force. You may convey, covered works to owners for the sole purpose of having them make modifications exclusive ways for you, or provide you with facilities for running the office work, provided that you comply with the terms of this License in conducting administrative for whom you do not control copyright. Those thus making or running the owners works for your owner are exclusively on your behalf. Under your direction and controls, on terms that prohibit them from missing any copies of your copyright material cut-off and/or otherwise being used by your conveying owner who overwitnesses it permitted solely under the conditions stated below. Sub-containing is not a loved, exced to make it unnecessary.

3. Protecting Users' Legal Rights From anti-Circumvention Law.

No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under articles 11 of the WIPC copyright. Pretty adopted on 20 December 1986, or similar leave prohibiting or restricting circumvention of such measures.

When you convey a covered work, you waive any legal cover to forbid circumvention of technological measures to the extent such circumvention is effected by expediting rights under this I consist with respect to the covered work, and you disclaim any information to limit operation or modification of the work as a means of enforcing, against the work's users, your or third parties legal rights to forbid circumvention of technological measures.

4. Conveying Verbatim Copies.

You may convey verbal copies of the Program's source code as you receive it, in any medium, provided that you conclusively and appropriately publish on each copy an appropriate copyright template; keep intact all notices starting that this License and any non-permitted license adders in accord with Section 1 apply to the code; keep intact all rounds of the absence or any warranty and give all recipients a copy of this License along with the Program. You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.

5. Conveying Modified Source Versions.

You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions:

a) The work must carry prominent notices stating that you modified i., and giving a relevant date.

(1) The work must carry prominent notices stating that it is recessed under this License and any conditions added under section 7. This requirement modifies the requirement in section 4 to "keep intact all notices".

c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any spottoeable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. The License gives no permission to license the work in any other way, but it does not invalidate such permission if you have necessary received it.

q) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program is interactive to interfaces that do not display Appropriate Legal Notices, your work need not, make them like a. A completion of a covered work with other apparatus and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of storage or distribution medium, is also an "aggregate." If the completion and its resulting copyright are not used to limit the access or legal rights of the completions uses beyond what the individual works permit inclusion of a covered work in an aggregate does not cause this license to apply to the other parts of the aggregate.

6. Conveying Non-Source Forms.

You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine readable. Corresponding Source under the terms of this License, in one of these ways:

a) Conway the object code In, or embodied in a physical product (including a physical distribution medium), accompanied by the Corresponding Source method on a durable physical medium customarily used for software Interchange.

(2) Convey the physical code in, or entitles in, a physical product including a physical distribution medium, accompanied by a written citer, valid for at least three years and valid for as long as you offer some parts or quotes nor support for that product model. To give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software merchandise, or a price no more than your reasonable cost or physically permitting this conveying at source, or (2) access to copy the Corresponding Source team's network server at no charge.

c) Convey individual copies of the object code with a copy of the written letter to provide the corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you received this object code with such an offer, in accord with subsection lib.

Convey the object code by differing access from a designated place (gratic or for a charge), and after equivalent access to the Corresponding Source in the same way through the same place as to further change. You need not require recipients to copy the Corresponding Source along with the object code. If the place is copy the object code is a network server, the Corresponding Source may be on a different server (optimized by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions react to the object code saying where to find the Corresponding Source. Recognizes of what server hosts the Corresponding Source, you remain obligated to ensure that it is available for as long as rounded to satisfy these requirements.

e) Convey the product code using peer-to-peer transmission, provided you to inform other peers where the object code and Corresponding Source of the work are acting effects to the general public at no charge under suspicion if it. A spontaneous person of the object code, whose source code is excluded from the Corresponding Source as a System library, cannot not be included in conveying the object code work. A "User Product" is either (i.e., "consumer product", which means any tangible personal property which is normally used for personal, family or household purposes, or (ii) anything designed or said in incorporation on into a dwelling. In determining whether a product is a consumer product, doubtful case shall be resolved in favor of coverage. For a particular product received by a particular use, "normally used" refers to a typical or common use of that class of product, or regardless of the status of the particular user of the role in which the particular user actually uses, or aspects or is specified to use; the product. A product is a consumer product registered with the product or its own product have substantial commercial, industrial or non consumer uses, unless such uses represent the any significant model used in the product.

"Installation Information" for a User Product means any methods, procedures, authorization keys, or other information required to install and execute installed versions of a source work in their User Product from a modified version of the Corresponding Source. The information must suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with either because modification has been made. If you convey on object code work under this section in, or with, an specificity or use in a User Product, and the corresponding occurs at part of a transaction in which the right or attention is not allowed by any person. The information is not allowed by any person to be used. For example, the following source conveyed under this execution must be accomplished by the Installation Information. But this requirement does not yet, neither you nor any third party relates the ability to install modified object code on the User Product (for example, the work has been installed in RIOV).

The requirement to provide installation information does not include a requirement to continue to provide support service, warranty, or updates on a work that has been modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be done when the modification itself is materially and adversely affects the operation of the network or switches the rules and protocols for communication across the network. Corresponding source conveyors, and installation information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and must require no approval answers or any for permitting, residing or copying.

7. Additional Terms.

'Additional commissions' are terms that supplement the terms of this license by making except one or more of its conditions. Additional commissions that are applicable to the entire Program shall be treated as enough they were included in this license, so the extent that they are valid under applicable law. It additional permissions apply only to case of the Programs, that plan may be used separately under these permissions, but the entire Program remains governed by a long, without regard to the additional permissions. When you convey a copy of a covered work, you may at your option remove any additional permission from that copy, or from any part of it. (Additional) permissions may be written to regulate their own removal in certain cases when you modify the work.) You may close additional permissions on material, address by you to a covered work, or which you have or can give appropriate copyright permission. Notwithstanding any other provision of this license, for matters you add to a covered work, you may it ultimately be by the copyright headers of that matching supplement the terms of the License with terms:

a) Declaining warranty or limiting liability differently from the terms of sections 15 and 18 of this License; or

(b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notice displayed by worse containing it; or

c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the original version or

d) Limiting the use for publicly purposes of names of licences or authors of the material; or

e) Desiring to prani rights under trademarks have for use of some trade names, trademarks, or service marks; or

1. Requiring indemnification of forearms and authors of this material by anyone who covers the material for modified versions of ill with contractual assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose or those licencees and authors. All other non-parmotative additional terms are considered "author contractors" within the meaning of section 10. If the Program as you received it, any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits reverancing or conveying under the license, you may also to a covered work material governed by the terms of main license document, produced that the restriction does not survive such eliminating or conveying. If you add terms to a works with in accord with this section, you must place. In the relevant source file, a statement of the additional terms that apply to those files, or a notice indicating whether to be issued or otherwise, will not be permitted to consider, may be stated. In the term of a separately written license, or related as exceptions; this above requirements are other ways.

8. Termination.

You may not propagate or modify a covered work except as expressly provided under this License. Any attempt, otherwise to propagate or modify it is void, and will automatically terminate your rights under the License (including any patent licenses granted under the third paragraph of section 11).

However, if you lease all valuation of this License, then your license from a particular copyright holder is reinstated (as) previably, unless bound to the copyright holder explicitly and finally letterizes your licenses, and be permanently, if the copyright holder lasts to notify you off the violation as some reasonable means prior to 10 days after the cessation. Moreover, your license from a particular copyright holder is reinstated permanently. If the copyright holder meets you some valuation by some reasonable means, this is the first time you have received notice of violation of the License for any work from that document holder, and you must the right to pay the claim against your request of the rights. This matter of your rights under the resale order will not rule the holder's rights to have issued or rights from any other under this License. If you have not been verified and not permanently, Thatled, you do not qualify to receive more licenses for the same material under section 10.

9. Acceptance Not Required for Having Copies.

You are not required to accept this License in order to receive or run a copy of the Program. And many propagation of a covers work accounting solely as a consequence of using peer-to-peer transmission to receive a copy. We believe does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions might copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your acceptance of the License to do so.

10. Automatic Licensing of Downstream Recipients.

I shall then you convey a covered work, the recipient automatically receives a license from the original licenses, to run, modify and propose that work, subject to this License. You are not responsible for enforcing compliance by third parties with this License. An "only transaction" is a transaction transferring control of an organization, or substantially all assets of one, or developing an organization, or integrating organizations. If proconsolation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party's predecessor in Interest had or could give under the previous paragraph, plus a right to processes on the Corresponding Sources of the work from the predecessor in Interest. In this predecessor has it or can get it with reasonable attitudes. You may not impose any further mechanism on the exercise of the rights granted or affixed under the provisions which will be required to accept any liability whatsoever arising from the provisions under this license, and you may not influence litigation (including a bronze-steam or claim in a lawsuit regarding that client claims incurred by making, using, selling, charging or sale, or importing the Program or any portion of it).

11. Patents.

A "contributor" is a copyright holder who authorizes use the License of the Program or a work on which the Program is based. The work thus ordered is called the contributor's "contributor version". A contributor is "seaside patent claim" as all patent claims owned or controlled by the contributor, whether already acquired or herector acquired, that would be infringed as one manner prompted by its license, of making, using, or acting its contributor version, shall do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, control includes the entire to gain patent, sublicensed in a manner consisting with its requirements of this License. Each contributor gives you a non-executive responsibility to the contribution of the essential patent claim, to make, use, sell, offer for sale, import and other tax-in, locally and propagate the contents of its contributor version.

In no following three paragraphs, a patent license is any express agreement or commitment, however demonstrated, not to enforce a patent (such as an express permission to practice a patient or covenant not to issue for patent infringement). To grant's such a patent license is a party means to make such an agreement or commitment not to enforce a patent against the party. If you convey a covered work, knowing relevant on a patent license, and the Corresponding Source of the work is not available for anyone to access, free of charge and under the terms of this License, though it publicly available network server or other radioactive means, than you must either (i) cause the Corresponding Source to be so available, or (ii) arrange to display yourself of the benefit of the information of the person who has been informed that you may have a copy of the correspondence from your own professional recipients. "Known relaying" means you have actual knowledge that, but for the patient, hence, your conveying the covered work in a country or your respect is true of the covered work in a country, would infringe one or more identifiable patents in that country, that you have reason to believe are valid if, pursuant to or in connection with a single transaction or arrangement, you convey, or prographs by procuring conveyance of a covered work, and grant a

patient license to some of the parties receiving the covered work authoring them to us, procreate, recally or convey a specific copy of the covered work, than the patient license you grant a automatically extended to all recipients of the covered work and works based on it. A patent license is "discriminatory" if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically granted under this License. You may not convey it covered work if you use a party to an arrangement with a third party that is in the business or distributing software, under which you make payment to the third party based on the extent of your activity at conveying the work, and under which the third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent leave

(s) In connection with copies of the covered work conveyed by you (or copies made from three copies), or

(b) primarily for and in connection with specific products or correlations that contain the owned work, unless you entered into that arrangement, or that patent license was granted, prior to 25 March 2007. Nothing in the License shall be construed as excluding or limiting any implied license or other defense to infringement that may otherwise be available to you under applicable patent law.

12. No Surrender of Others' Freedom.

It conditions are imposed on your heterogeneous court order, agreement or otherwise that contradicts the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously our obligations under the License and any other certain obligations, then as a consequence you may not convey it still. For example, if you agree to ensure that obligate you to collect a royalty for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to obtain entirely from conveying the Program.

13. Use with the GNU Affero General Public License.

Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 8 of the GNU Aftero General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the port which is the covered work, but the special requirements of the GNU Aftero General Public License, sect on TO, concerning interaction through a network will apply to the combination as such.

14. Revised Versions of this License.

The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in going to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version on number. If the Program specifies that a certain number of version of the GNJ General Public License ("or any later version") applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free Software Foundation. In the Program does not specify a version number of the GNJ General Public License, you may choose any version ever published by the Free Software Foundation. If the Program specifies that a proxy can decide which future versions of the GNJ General Public License can be used, that predicts the public statement of acceptance of a version permanently authorizes you to choose that version for the Program. Later license versions may give you, additional or different permissions. However, no additional obligations are imposed on any other or copyright holder as a result of your choosing to follow a later version.

15. Disclaimer of Warranty.

THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PREFERENCE. THE ENTRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU SHOULD THE PROGRAM PROVE DETECTIVE. YOU ASSUME THE COSTS OF ALL NECESSARY SHAVING, HI PAIR OR CORRIFICATION.

16. Limitation of Liability

IN NO - V-NT UNI - SS & KNIDU AT APPLICAT I LAW OR AGREED TO IN WRITING WITH ANY COPYRIGHT HOLDER, OR ANY CHIEF PARTY WHO MODELS AND/OR COMPAYS THE PROGRAM AS PERMITTED ABOVE RELIABLE TO YOU FOR DAMAGS, INC. USING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING PROCESSED IN ACCURATE OR LOSSSES SUSINUED BY YOU OR IF IND PARTIES OR A FAILURE OF THE PROGRAM TO OFFERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGS

17. Interpretation of Sections 15 and 16.

If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, retrieving courts shall apply locally law that most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of facility accommodates a copy of the Program in return for a fee.

OpenSSL Combined License

The OpenSSI toolkit stays under a dual license, i.e. both the conditions of the OpenSSI license and the original SSI say license apply to the lookit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any licensed Issues related to OpenSSI, please contact [e-mail].

Component Name License URL

openssl-1.0.2e OpenSSL Combined License http://www.openssl.org/source

Copyright (c) 1998-2011 The OpenSSI Project. All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Recistributions of source code must retain the above copyright notice, this list of conditions and the following disclaims:

2. Recistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the emitter button.

3. All advertising materials mentioning features or use of "a software must display the following acknowledgment: 'This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit: http://www.openes.org/'"

4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from the software without prior written permission. For written permission, please contact [e-mail].

5. Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the OpenSSL Project.

6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http://www.openssl.org/)"

THIS SOI WAR is PROVIDED BY THE OFFICE'S PROJECT "AS IS" AND ANY OPPOSITE OR IMPRIED WARHANIS, INCLUDING JUST NOT LIMITED TO THE IMPLIED WARRANTIES OF MERO INVIABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCRIMED. IN NO EVENT SHALL THE OPENILL PROJECT OR ITS CONTRIBUTIONS BE LIABLE FOR ANY DIRECT INDIRECT, INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE, DATA, OR PORTS; OR BUSINESS INTERRUPTION HOWEVER CAUSED ON ANY HISTORY OF ABILITIES WHETHER IN CONTRACT, STRICT ABILITY OR TORT INCLUDING NEGUSING NO OR OTHER KASH ARISING IN ANY WAY OUT OF THE USE OF THIS SOI WAR, EVENT A MISSED OF THE POSSIBILITY OR SUCH DAMAGE

Original SSLeey License

Copyright © 1985-1995 Eric Young ([e-mail]) All rights reserved.

This package is an SSL implementation written by Eric Young (eavforsprosoft.com).

The implementation was written so as to conform with Necospee SSL.

This library is not for commercial and non-commercial use as long as the following conditions are sheeted to. The following conditions apply to all codes found in this distribution, be: the PCA, RSA, Hash, DES, etc., code; not used the SSL code. The SSL documentation included with the distribution is covered by the same copyright terms except that the holder is Tim Hudson [e-mail].

Copyright remains Efe Young's, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation online or lexually provided with the package. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met.

1. Reclassifications of source code must retain the copyright notice, this list of conditions and the following disclaimers.

2. Recistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning textures or use of the software must display the following acknowledgment: "This product includes cryptographic software written by Eric Young (pay&cryptsoft.com)" The word "cryptographic" can be left out if the routines from the library being used are not cryptographic related to.

4. If you include any Windows specific code (or a derivative thereof) from the appe directory (application code) you must include an acknowledgement: "This product includes software written by Tim Hudson (chiloryptact, com)"

THIS SOFTWARE IS PROVIDED BY THE YOUNG "AS IS" AND ANY BUSINESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT USED. The IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR INFORMATION. ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR ON CONTRIBUTORS BE LIABLE FOR ANY INDIRECT, INDIRECT, INCIDENTAL SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT USED. PROCUMPTIONS OF SUBSTITUTIONS (GOODS AND SERVICES) LOSS OF US, DATA, OR PROHIBITED, OR BUSINESS INFORMATION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The licence and distribution terms for any publicly available version or derivative of this code cannot be charged. i.e. the code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.]

BSD License

Some software components of the product incorporate source code covered under the BSD license as follows.

Component Name License URL

net-rimp-3.75	ISO	https://www.net-rimp.org/about/licenses.html
pons-8.86	850
Ibsp-1.7.4	850 2.0	http://www.klernel.org/pub/linux/ba/security/linux-private/Ibsp2
Igltcod-1.4.85	850 2.0	http://www.opensource.org/licensesbed-licenses.html
MiniPrP Project Client	850 2.0
pppd 24.6	HSD 7.0	http://epzresource.org/licenses/HSD 3 Clause

I gited up at a secure, last, comptant, and very leadable webserver that has been optimized for high-performance environments. It has a very low memory footprint compared to other webservers and drives case of codious. Its enhanced feature-reel (FastCOI, CGI Auln, Output-Compression, UPL-Tewriting and many more) make lightped the perfect webserver-software for every server that suffers load problems. Simple Network Management Protocol (SNMP) is an interstandard protocol for managing devices on IP networks. It is used mostly in network management systems to monitor the devices attained to the network for conditions that meet administrative activities. Net SNMP is a suite of acquisitions used to implement SNMP v1, SNMP v2e and SNMP v3 using both IPA4 and PVB4 for more additional information, send email to [e-mail].

Copyright © 2004. Knoechke, incremental

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

- Distributors or sources made must retain the above copyright notice, this list or conditions and the following disclaimer. - Distributors in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distributor. Neither the name of the "intermodal" nor the name of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFA WARE IS PROVIDED BY THE COPYRIGHT ITEMS AND CONTRIBUTORS "ABS" AND ANY EXPRESS OR IMPLED WARRANTIES, INCLUDING, BUT NOT LIMITED, TO THE IMPLED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT, IN CAPITAL SPECIAL EXEMPLARY ON CONS. (OUT) NEW DAWA'S INCLUDING, NOT NOT LIMITED TO PROCUREMENT OR SUBSTITUTE GOODS OR HYDICULTS OF USA, DATA OF THIS INFORMATION, ANY OTHER ASSEMBLY ON YOUR BASIS AND ON ANY THEORY OR LIABILITY SHEET IN CONTROL RIGHTS OF TORT, INCLUDING NEGLIGENCE ON OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IT FAVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Copyright (c) 2008 2001 University College London

At rights reserved

Pedestition and use in source and binary forms, with or without modification, is omitted provided that the following conditions are met

1. Recistributions of source code must rear the above copyright notice, this list of conditions and the following disclaimer.

2. Reclassibutions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution:

3. At advertising materials mentioning lectures or use of this software must display the following acknowledgement: This product includes software developed by the Computer Science Department at University College London.

4. Neither the name of the University nor of the Department may be used to endorse or promote products derived from the software without specific prior written permission

THIS SOFRY IS PROVINCIBLE BY THE AUTHORS AND CONSTITUCERS ASIS AND ANY EXPRESSED OR IMPLICABLE WARRANTIES, INCLUDING, BUT NOT LIMITED TO THE IMPLED WARRANTIES OF MERCANUABILITY AND THLESS FOR A PARTICULAR PURPOSE, DISCLAIMLY, IN NO EVENT SHALL THE AUTHORS ON CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL OTHERWISE. ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANOTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER

All rights reserved

Red distribution and use in source and binary forms, with or without modification are permitted provided (has the following conditions are true:

1. Recistributions of source code must return the above copyright notice, this list of conditions and the following disclaimer.

2. Recistributions in binary form must reproduce the above copyright route, this list of conditions and the following disclaimer in the documentation and/or other materials provided with no attribution.

3. Neither the name of the Regents of the University of California nor the names of its contributions may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS AS BY AND ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER FOR CONTRIBUTORS IS BASED FOR ANY DIRECT INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, PROCUMPTION OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE, DATA OF PROCESSING, OTHER INTUPTIONS, OTHER CHARGES AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY, OR WITHOUT PERMISSION OR WITHOUT ANY OTHER ASPIRIT, WITHOUT ANY OTHER ASPIRIT OR WITHOUT ANY OTHER ASPIRIT OR WITHOUT ANY OTHER ASPIRIT OR WITHOUT ANY OTHER ASPIRIT OR WITHOUT ANY OTHER ASPIRIT OR WITHOUT ANY OTHER ASPIRIT OR WITHOUT ANY OTHER ASPIRIT OR WITHOUT ANY OTHER ASPIRIT OR WITHOUT ANY OTHER ASPIRIT OR WITHOUT ANY OTHER ASPIRIT OR WITHOUT ANY OTHER ASPIRIT OR WITHOUT ANY OTHER ASPIRIT OR WITHOUT ANY OTHER ASPIRIT OR WITHOUT ANY OTHER AT

Copyright © 2005. Creative Labs Inc

All rights reserved.

Red distribution and use in source and binary items, with or without modification are permitted provides that the following conditions are met:

1. Realizations of source code must rear the above copyright notice, this list of conditions and the following disclaimer:

2. Restricturalkins in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with no distribution.

3. Neither the name of the Creative Lace nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT CHECKS AND CONTRIBUTORS "ABS" AND ANY EXPRESS OR IMPERITIVARIANTS, INCLUDING, BUT NOT LIMITED, TO THE IMPLED WARANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLOSED. IN NO EVENT SHALL THE COPYRIGHT OWNER FOR CONTRIBUTIONS BE INSTALLED FOR ANY EFFECT, INDICIPAL, SPECIAL, EXPPLICARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED, TO PROCEDURE OF SUBSTITUTE GOODS ON SERVICES, LOSS OF USE, DATA OF PROPERTY HOLDING INTLINGTON WOOD CHASES AND ON ANY THEORY OF LEADUSTRY WHETHER IN CONTRACT, STRICT LIABILITY, OR (INCLUDING) WITHOUT ANY OTHER IN THIS DRAWING IN ANY WAY OF THE USE OF THIS NOTICE, PARTN AUTHORITY OF THE POSSIBILITY OF SUCH DAMAGE.

Copyright (c) 2005 7012, Thomas H-ENAHJ

All rights reserved

Redistribution and use in source and binary forms, with or without modification are permitted provided that the following conditions are met:

1. Reclassibutions of source code must rear the above copyright notice, this list of conditions and the following disclaimer

2. Recirculation in binary form must reproduce the above copyright notice, this list of conditions and the following declaration in the documentation and other materials provided with the distribution.

3. Neither the name of Thomas EE7VAND nor the names of te contributors may be used to endorse or promote products derived from the software without specific policy written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS ON IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTIONS ARE UNEER FOR ANY INDIRECT, INCIDENTAL, SPECIAL, SNMP ANY OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA OR PROFITS; OR BUSINESS INTERRUPTIONS HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT, STRICT LIABILITY, OR

ICH | INCLUDING NEGUNG OR OTHER ASIS, ARISING IN ANY WAY OUT OF THE USE OF THIS SCIF WAIH, EVENT ADMIED OF THE POSSIBILITY OF SUCH DAMAGE

Ver oue copyrights apply to the package, listed in various separate parts below. Please make sure that you read all the parts.

Parl 1: CMU/UCD copyright notice: (USD like)

Copyright 1989, 1991, 1992 by Carnegie Mellon University Derivative Work - 1995, 1993-2000

Copyright 1986. 1986-2003 The Regents of the University of California

All Rights Reserved

Promissors to use, copy, mostly and distribute this software and its documentation for any purpose and without loss a hereby granted, produced that the above copyright notice appears in all copies and that the third copyright notice and the permission notice appear in supporting documentation, and that the same of CMU and The Regents of the University of California not be used in advertising or publicity pertaining to distribution of the software without specific written permission.

OMU and THE REGENTS OF THE UNIVERSITY OF CALIFORNIA DISPLAY ALL WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL CMU ON THE REGENTS OF THE UNIVERSITY OF CALIFORNIA BE TREAT FOR ANY SPECIAL INCH OF OR CONSULTING DAMAGES OR ANY DAMAGES WITHOUT THE USE OF USE - DATA OF PROFITS, WHETHER IN AN ACTION OF CONTRACT, INSUSENCE OR OTHER TORTICUS ACTION ARISING OUT OF OR IN CONNECTION WITH THE USE ON PERFORMANCE OF THIS SOFTWARE.

Part 2: Networks Associates Technology, Inc copyright notice (BSD)

Copyright © 2001-2003, Network Associates Technology, Inc.

All rights reserved

Prelatitution and use in source and binary forms, with or without modification are permitted provided that the following conditions are met: y Prelatibutions of source code must retain the above copyright notice, this list of conditions and the following disclaimer, y Reclastibutions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution, y Neither the name of the Networks Associates Technology, Inc. nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ASSIST AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPILED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCUMED. INFOLY SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS IS MAINT FOR ANY OTHER, INDICIPAL, INDICIPAL, SPECIAL, EXHIMARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, LOSS OF USE, DATA OR PROFITS, OR SURSES INTUITIONS, HOARLY CAUSED AND ANY THYBER OF ABWI YHEATH IN CONTRACT, DIRECT ABWIY, OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHERS OR ANY OTHER S

Part 3: Cambridge Broadband Ltd. copyright notice (BSD)

Portions of this code are copyright (p) 2001-2003, Cambridge Broadband Ltd.

All rights reserved

Predistribution and use in sources and binary forms, with or without modification, are permitted provided that the following conditions are met: y. Recistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer, y. Recistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution, y. The name of Cambridge Broadband Ltd. may not be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS TRAVED BY THE COPYRIGHT HOLDER "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED, TO THE IMPLED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCHAINED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED. PROCESSED BY BUSINESS (THIS) THIS INFORMATION CONTACTS ON THE INFORMATION WRITTEN BASIS AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY, OR TORT (INCLUDING NEGENDENCE OR OTHERWISE AREING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE

Part 4: Sun Microsystems, Inc. copyright notice

BSC

Copyright (c) 2003 Sun Microsystems, Inc. /150 Network

Circle, Santa Darc, California 9505°, U.S.A.

All rights reserved

Use is subject to license terms below. This distribution may include material developed by third series. Sun, Sun Microsystems, the Sun logo and Series are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries. Redistribution and use in source and binary forms with or without modification, are permitted to provide that the following conditions are met by Kreditbursis or source code must retain the above copyright notices, this list of conditions and the following deadline by Redistribution in library form must reproduce the above copyright notice, this list of conditions and the following declaration in the documentation and/or other notes provided will the distribution by whether the name of the Sun Microsystems, Inc., nor the names of its contributors may not be obtained or promotes products known from the software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT BELIE TO, THE WRITTEN WARRANTY IS OF THIS INFORMATION AND IN SICIL OR A SPECIFIC PURPOSE, ARE ONLY AND IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, LOSS OF USE, DATA AND ANY OTHERS. ANY OTHERS WILL BE USED IN CONKAGE, TIMING, WARRANTY, OR OTHER (INCLUDING AS SPECIFIC OR OTHERWISE), ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN FEEDMENT OF THE POSSIBILITY OF SUCH DAMAGE.

Part 5: Sperta, Inc copyright notice (BSD)

Copyright 16:2003-2009, Santa, Inc.

At night reserved

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: by Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimers. By Redistribution in binary form must reproduce the

above copyright notice, this list of conciliaries and the following disclaimer in the documentation and/or other materials provided with the distribution: yv. Neither the name of Sparks, Inc nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "ASIS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPERED WARPLAN IS OF WHICH AVAILABLE AND HILLS FOR A PARTICULAR PURPOSE. ARE DISC. AIMED IN NO EVENT SHALL THE COPYRIGHT HOLDERS OF CONTRIBUTIONS BE LIABLE FOR ANY DIRECT INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, EQUITY, OTHERS) OR ANY THIS DRAWING ASSETS SHALL BE ASIALED OR ANY HISTORY OF WARRANTY (WITH ANY INFORMATION SHOULD NOT AUTHORIFY ON FRONT INCLUDING NIS & GENDER OR BY PRAISE) ARISING IN ANY WAY TO THE USE OF THIS SOFTWARE, UN IT AVAILABLE OF THE POSSIBILITY OF SUCH DAMAGE.

Part 6: Cisco/BUPTNIC copyright notice (BSD)

Copyright (c) 2004, Glosco, Inc. and Information Network

Center of Beijing University of Poeta and Telecommunications.

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted to produce that the following conditions are met: y. Redistribution of source code must wear the above copyright notice, this list of conditions and the following disclaimers: y. Redistribution in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimers in the documentation and/or other materials provided with the distribution; y. Neither the name of Cisco, Inc., Belling University of Posts and Telecommunications, nor the names of mail contributors may be used to endorse or promote products derived from the software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "ASIS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT, INCIDENTAL, STRUAL, EXEMPLARY, OTHERS, PATENTS (IN ACCORDANCE) (NO UNITS) WITHOUT ANY ANY ANY THIS DRAWING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SHIRCONS, USE OF USE, DATA OF PROFITS, OR BUSINESS INTERRUPTION, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT, STRICT LIABILITY, OR SHORT (INCLUDING NO. GRENCE OR OTTAWISH), ARISING IN ANY WAY OUT OF THE USE. IS THIS SOFTWARE, EVEN IT AVAILABLE OF THE POSSIBILITY OF SUCH DAMAGE.

Part 7: Fabasoft R&D Software Software GmbH & Co KG copyright Notice (BSD)

Copyright (c) Fabesoft BSI Software GmbH & Co KG, [e-mail]

Author: Bernhard Penz

Her distribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yj. Redistribution of source code must remain at the above copyright notice, this list of conditions and the following disclaimer, yj. Redistribution in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution, yj. The name of Fisbasom 830 Software GmbH & Co KG or any of its subsidiaries, brand or product names may not be used to endorse or promote products offered from the software without scientific or written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLD-E "AS IS" AND ANY EXPRESS OR IMPATH WARRANTIES, INCLUDING, BUT NOT IMH

TO, THE IMPLD WARRANTIES OF MICROINABILITY AND THIS STOCK FOR A PARTICULAR PURPOSE AND DISCLAIMED, IN MOVEMENTS WILL THE COPYRIGHT HOLDER BE LIABLE FOR ANY DIRECT. INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS ON SERVICES; LOSS OF USE, DATA, OR PROFITS; ON BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT, INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Part 8: Apple Inc. copyright notice (BSD)

Copyright (c) 2007 Apple Inc.

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistribution of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Registrations in binary form must introduce the above copyright notice, this list of conditions and the following disclosure in the documentation and/or other materials provided with the distribution. 3. Neither the name of Apple Inc. ("Apple") nor the names of its contributions may be used to endorse or promote products derived from this software without explicit prior written permission.

THIS SOFTWARE IS PROVIDED BY APPLE AND ITS CONTRIBUTORS "A\$ 81" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED, IN NO EVENT SHALL APPLY OR SHOULD NOT BE HELD FOR ANY IMPROVATION, INCIDENTAL, SPECIAL, EXHIBILARY OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE OF GOODS OR SERVICES, LOSS OF USE, DATA, OPPTS, OR BUSINESS INPPRIALS ON HOMMES CAUSED ON ANY HISTORY OF LIABILITY WHICH IN CONTRACT, WHICH LIABILITY OF LICITING USING

Prol 0, Pivotal pain, L12, Copyright: Pfizer (RSD)

Part 6. DeutscheLog, EBO Copyright

Copyright (c) 2005, ScienceLogic, LLC

All rights reserved.

Redistribution and user in source and binary forms, with or without modification are permitted provided that the following conditions derived: yi Redistribution of source codes must retain the above copyright notice, this list of conditions and the following disclaimer: yj Redistribution in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and other matches provided within the distribution. yj Neither name or Science.org, LLC nor the names of its contributions may be used to endorse or promote products derived from the software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS' AS IS AND ANY EXPRESS ON IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCUED. ADMID: IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT INFECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE POSICS OR SERVICES, LOSS OF USE, DATA AND OTHERS) OR ANY BUSINESS INSURPTION, RETAWERS CALIFER, AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT, STRICT LIBILITY OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH IDLAWAGE).

The MIT License

Some software components of this product incorporate source code covered under the MT license as follows

MIT License 2.0

Aeroginger, Ischemoers, Juncy U, Ilexi, IxxeP, Mesa3D, Mesal b, revEpican, OpenGI. Sampica Park, Valle Studio, xeng server, diaphoe 2012.55, nourse8-5.7

Copyright (c) 2011, The Dajo Foundation

Copyright 2010, AUTHORS.txt (http://quenvi.com/sbouri)

Dual licensed under the MIT or GPL Version 2 licenses.

- http://quany.org/licenses

- http://docs.query.com/UPWidget

Copyright Daniel Vallard

Copyright Igor /alatovic [e-mail]

Copyright Alesey Serin

Copyright Gary Pennington [e-mail]

Copyright Alfred Mickautsch [e-mail]

Copyright Bjorn Reese

Copyright Jood W. Food

Copyright William Brack [e-mail]

Copyright (c) 2007-2010 The Khronza Group Inc.

Copyright Atish Kumar Petra

Copyright © 2008 Free Software Foundation, Inc.

Permies on is hereby granted, free of charge, to any person obtaining a copy of this software and associates documentation file (the "Software"), to deal in the Software without restrictions, including without limitation the rights to use, copy, modify, merger, publish, distribution, broadband, and/or soil copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXCESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY. FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OF COPYRIGHT HOLDERS BEFORE ANY CLAIM, DAMAGES OR OTHER UTILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DIALINGS IN THE SOFTWARE.

Mozilla Public License

Since we, at Hanwhs, Techwin, used the Mozilla Firefox component without modifying the source code according to the MOZILLA Public License 1.1, we are not obliged to provide the source code of the corresponding component.

- Version 1.

1. Definitions.

1.0.1. "Commercial Use" means distribution or otherwise marking the Covered Code available to a third party.

1.1. "Corbinator" means each entity that creates or contributes to the creation of Modifications.

1.2. "Contributor Version" means the combination of the Original Code, prior Modifications used by a Contributor, and the Modifications made by that particular Contributor.

1.3. "Covered Code" means the Original Code or Modifications or the combination of the Original Code and Modifications, in each case including portions thereof

1.4. Electronic Distribution Mechanism* means a mechanism generally accepted in the software development community for the electronic transfer of data.

1.5. "Executable" means Covered Code in any form other than Source Code.

1.6. "Initial Developer" means the individual or entity identified as the initial Developer in the Source Code notice required by Exhibit A.

1.7. "Large Work" means a work which combines Covered Code or portions thereof with code not governed by the terms of this License.

1.8. "License" means this document.

1.8.1. "I compensable" means having the right to grant, to the maximum extent possible, whether at the time of the initial grant or subsequently acquired any and all of the rights conveyed herein.

1.9. "Modifications" means any addition to or deletion from the substance or structure of either the Original Code or any previous Modifications. When Covered Code is released as a series of files, a Modification is:

A. Any addition to or deletion from the contents of a Tie containing Original Code or previous Modifications.

B. Any newly filed that contains any part of the Original Code or previous Modifications.

1.10. "Original Code" means Source Class of computer software code which is described in the Source Data notation required by Exhibit A as Original Code, and which, at the time of its release under this License is not already Covered Code governed by this License.

1.10.1. "Patent Claims" means any patent claim(s), now owned or thereafter acquired, including without limitation, method, process, and apparatus claims, in any patent. Unobservable by grantor.

1.11. Source Code* means the presence form of the Covered Code for training modifications to all, including all measures it consists, plus any associated inference definition files, scripts used to control some relation and installation of an Execution, or course code differential comparison against either the Original Code or another well known, available Covered Code of the Contributor's choice. The Source Code can be in a compressed or actual form, provided the appropriate decomposition or de-creating software is widely available for no change.

1.12. "Your" (or "Your") means an individual or a legally existing rights owner, and complying with all or the items of, this license or a future version of this license issued under Section 6.1. For legal entities, "Your" includes any entity by which controls is controlled by, or is under common control with You. For purpose of this definition, "common" means (by the owner, other) to cause the direction or management of such entity, whether by contract or otherwise, or by ownership of more than fifty percent (53%) at the outstanding shares or noninterest ownership or such entity.

2. Source Code License.

2.1. The Initial Developer Grant. The Initial Developer hereby grants You a world-wide, royalty-free, non-exclusive license, subject to third party intellectual property claims:

(a) under Intellectual property rights (other than percent or trades) Ucochesible by India: Developer to use, reproduce, modify display perform, sublicense and distribute the Origin. Once for sections thereof, with or without Modifications, another as part of a larger Work; and

(b) under Patentis Claims infringed by the making, using or selling of Original Code. To make, have made, use, practice, sell and offer for sale, and/or otherwise disposes of the Original Code (or portions thereof).

(c) The license granted in this Section 2. (d) and (e) are effective on the date initial Developer first attributes Original Code under the terms of this License. (d) Notwithstanding Section 2.1(b) above, no patent. License is granted. (f) for some that. You defer from the Original Code, 2. excelsate from the Original Code, or (g) for our regiments caused by: (h) the redistribution of the Original Code or (i) the commission of the Original Code with other software or devices. 2.2. Contributor Grant. Subject to thirty party intellectual property owners, each Contributor hereby grants you a world-law, royalty-free, non-executive kernel.

(a) under infectious property rights (other than patent or trademark) is noticeable by Contributor, to use, reproduce, mostly display, perform, subsistence and distribute the Modifications created by such Contributor (or portions thereof either or an unmodified basis, with other Modifications, as Covered Code and/or as part of a Larger Work and

by under Patent Claims Inferred by the making, using, or selling of Modifications made by their Contributor other aims and/or in combination with its Contributor Version for portions or such combinations, to make use, act, offer for sale, have made, and/or otherwise disperse ct. 1) Modifications made by that Contributor for portions thereof; and 2) the combination or Modifications made by and Contributor with its Contributor Version for portions or such combinations.

(c) the licenses granted in Sections 2.2(a) and 2.2(b) are effective on the date. Contributor that makes Commercial Use of the Covered Code

(2) Notwithstanding Section 3 (4) by above, no patent license is granted. If any copy that Contributor has adopted from the Contributor Version 2, separate from the Contributor Version 3 for printing parts caused by, (3) third party modifications of Contributor Version or (4) the combination of Modifications made by that Contributor with other software used as part of the Contributor Version (or other devices; or if) under Patent Counter infringed by Covered Case in the absence of Modifications made by that Contributor.

3. Distribution Obligations.

3.1. Application of License: The Modifications which you create or to within You don't have been formed by the terms of this License, including without Infection Section 2.2. The Source Code version of Covered Code may be distributed only under the terms of the License or a future version of this User be released under Section 8.1, and you must include a copy of its license with every copy of the Source Code. You distribute that may not alter or improve any extent on any Source Code version that exceeds the approximate version of the License or the recipients' rights hereunder. However, You may include an additional document offering the additional rights dates in Section 3.5.

3.2Availability of Source Code. Any Modification which You continue to check You contribute must be made available in Source Code from under the terms of this License either on the same media as an Executable version or via a second Electronic Distribution Mechanism to anyone to whom you made an Executable version available, and I made available via Electronic Distribution Mechanism, must remain available or a related week '12 months after the date it initially became available, or at later 65 months after a subacquisition version of that particular Modification has been made available to such recipients. You are responsible for ensuring that the Source Code version remains available even if the Electronic Distribution Mechanism is maintained by a third party.

3.3. Description of Modifications. You must issue all Covered Code to which you contribute to contain a file documenting the changes. You made to create that Covered Code are the date of any change. You must include a continent statement that, the Modification is derived directly or indirectly, from Origin Code provided by the Initial Developer and including the name of the Initial Developer in the Source Code, and join in any notice in an Exectable version or related documentation in which you describe this origin or ownership of the Covered Code.

3.4. Intellectual Property Matters

(4) Frind Party Claims. If Contribution knowledge has knowledge that a license under a frind party intellectual property rights is required to exercise the rights granted by such Contribution under Sections 2.1 or 3.2, Contributor must include a list. We wish the Source Code distribution (the "LESA") which describes the claim and the party making the claim in sufficient detail that a credit will know whom to contact. If Contribution obtain such knowledge after the Modification is not available as described in Section 3.2, Contributor and promptly modify the LESA. In a copies contribution makes available transfer and shall take other steps such as anything appropriate mailing lists or reorganized reasonably calculated to inform those who receive the Source Code that new ownership has been distinctions.

(b) Contributor AFIs. If Contributor's Modifications include an application programming interface and Contributor has knowledge of patent licenses which are reasonably necessary to implement, Inst. AP. Contributor must also include the information in the LEGAL file.

(c) Representations:

Contributor represents that, except as disclosed pursuant to Section 8.4(a) above. Contributor believes that Contributor's Modifications are Contributor's original creation(s) and/or Contributor has sufficient rights to grant the rights conveyed by this License.

3.8. Recommended Notes: You must duplicate the notice that I am such like the Source Code. It is not possible to put such notice in a particular Source Code for due to its structure, then you must include such notice in a location such as a relevant directory where a prior would be likely to look for such a notice. "You must be one or more Modified You may sub your name as a Contributor. To the notice does not in Exhibit A, 'You must also dpulize the License in any document for the Source Code where You decide to replace rights and responsibility rights relating to Covered Goods. You may choose to order, and to change a fee for warranty, support, indemnity or facility obligations to one or more contracts on Covered Goods. However, You may do so only on your own behalf, and on her behalf other than a future offer or any Contribution. You must make it absolutely clear their are such warranty support, indemnity or facility obligation is offered by You alone, and You merely agree to infermily the mus Developer and every Contributor for any facility incurred by the minor Developer or such Contributor as a result of warranty support, intermittently or facility name You offer

3.8. Distribution of Exercisable Versions. You may distribute Covered Code in Execusable form only if the requirements of Section 3.1. To have been met or not Covered Code, and if you include a notice listing this, the Source Code version of the Covered Code is available under the terms of the License, using a description of how and where You have fulfilled the obligations of Section 3.2. The notice must be consciously involved in any notice if an Executable version, related documentation or collateral in which You describe recipients' rights relating to the Covered Code. You may distribute the Execution version of Covered Code or oncogenic rights under a license or your choice, which may contain items different than this license, provided that You are in compliance with the terms of this license and that the License

for the Exercisable version does not attempt to limit or alter the recipient's rights in the Source Case version from the rights set forth in this License. It you distribute the Exercisable version under a different license. You must make it absolutely clear that any terms which differ from the Licensee are offered by You, and, nor by the Initial Developer or any Contributor. You hereby agree to acceptify the Initial Developer and every Contributor for any liability incurred by the Initial Developer or each Contributor as a result of any such terms. You offer

3.7. Larger Works. You may create a larger Work by combining Covered Goods with other code not governed by the items at this License and distribute the Large Works as a single product. In such a case, you must make sure the requirements of this License are fulfilled for the Covered Code.

4. Inability to Comply Due to Statute or Regulation.

It is impossible for you to comply with any of the terms of this license with respect to some or all of the Covered Code due to statute, judicial order, or regulation then. You must be comply with the terms of this License to the maximum extent possible, and for certain the imbalances and the code they affect. Such deferor plan must be included in the LEGAL file described in Section 3/4 and must be included with all distributions of the Source Code. Except to the extent prohibited by statute or regulation, such description must be sufficiently obtained for an element of ordinary skills to be able to understand it.

5. Application of this License.

This License applies to code to which the Initial Developer has attached the notice in Exhibit A and to rated Covered Code.

6. Versions of the License.

6.1. New Versions, Netscape Communications Corporation ("Nelscape") may purchase revised and/or new versions of the License from time to time. Each version will be given a distinguishing version number.

6.2. Effect of New Versiona. Once Covered Code has been published under a particular version of the License, You may always do must to use it under the terms of that version. You may also choose to use such Covered Code under the terms of any subsequent version of the License published by Netscape. No one other than Netscape has the right to apply the terms applicable to Covered Code created under this license.

6.3 Derivative Works. If you create or use a modified version of this License (which you may only do in order to apply in the code which is not already Covered Code governed by the License). You must buy the license so that the addresses "Model", "MOZZILATC", "MOZPL", "Nassace", "MTL", "NFL" or any confusing view printed, but not appear in your license (also to note that your license offers from the license area) or otherwise made it soon that your version of the license contains terms which differ from the formula Public License and Nassace Public License. Filing in the name of the Initial Developer, Original Code or Contributor in the notice describes in Latin Alari not of themselves be deemed to be implications of this License).

7. DISCLAIMER OF WARRANTY.

COVERED CODE: A PROVIDED UP OF THE LIGE ON AN AS BASIS, WITHOUT WARRANTY OF ANY ONE, EITHER NAME, VALID OR IMPLIC, INCLUDING WITHOUT LIMITATION, WARRANTIES THAT THE COVERED CODE IS FREE OF DETAILS; MERCHANTABILITY, FIT FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT. THE ENTIRE RISKS AT THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH YOU SHOULD ANY COVERED CODE PROVE DEFECTIVE IN ANY RESPECT. YOU NOT THE INITIAL, DEVELOPER OR ANY OTHER CONTRIBUTOR, ASSUME THE COST OF ANY INCESSARY SERVICING, IMPAIR OR CORRICTION. THIS DESCRIPTION OF WARRANTY CONSTITUTS AN ADDITIONAL PART OF THE EIGHT, NO USE OF ANY COVERED CODE IS AUTHORIZED BY YOUR INFORMATION.

8. TERMINATION.

8.1. This License and the rights granted her under will terminate automatically if you fail to comply with terms remain and fail to cure such breach within 30 days of becoming aware of the breach. All insurances to the Covered Code which are properly granted shall survive any termination of the License. Specifications which, by their nature, must remain in office beyond the termination of this license shall survive.

8.2. If You Initiate, hsgater by caseiting a patent infringement claim (excluding statutory judgment actions) against the Developer or a Contributor that Initial Developer or Contributor against whom You Tre such action is referred to as "Participant" alleging that:

As such Participants Contributor were online or directly infinite any parent, then any and all rights granted by such Participants to Your Under Sections 2.1 and/or 2.2 which is a license shall open 60 days notice from Participants to minors appropriately unless within 60 days after receipt of notice You should be given in writing to pay Participants to mutually agree responsible royalty for Your Trust and Future Use of Modifications made by such Participant, on which you have Your Eligations claim with respect to the Contribut or Version against such Participants. It when 60 days of notice, a reasonable royalty and payment arrangement are not individually agreed upon in writing by the parties or the litigation claims is not without, the rights granted by Participant to Your Under Sections 2.1 online 2.2 automatically terminate at the expiration of the 60 day notice period specified above.

(b) any so more, hardware, or device, other than such Participa's Contributor Version, directly or indirectly in ranges any patents, rem any rights granted to You by such Participa under Sections 2.1(b) and 2.2(b) are revolved effective as of the date You first made, used, sold, distributed or hard mode, Modifications made by this. Participa part.

8.5. If you assert a latent infringement claim against Participant alleging that such Participant's Contributor Version directly or indirectly infringes any patent where such claim is received such as by license or settlement prior to the initiation of latent infringement litigation, then the reasonable value of the licenses granted by such Participant under Section 2.1 or 2.2 shall be taken into account for determining the amount or value of any payment or license.

8.4. In the event, termination under Descruits 0.1 or 0.2 above, all end user license agreements (excluding distributors and resellers), which have been validly granted by You or any distributor nor under prior to termination shall survive termination.

9. LIMITATION OF LIABILITY.

UNDER CHOURNISH AND UNDER NOBA THEORY WITH THE RIGHT (INCLUDING NEACH-CONTINUM, OR OTHER) SHALL YOU. ITAL INFORMATION ANY OTHER CONTRIBUTION OR ANYIS RELATION OF COIL RED COLD OR ANY SUPERIOR ANY OF SUCH RAPE IS UNITS TO ANY PERSON FOR ANY INDIRECT SPECIAL, INCENTRAL OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER INCLUDING WITHOUT LIMITATION, DAMAGES FOR THIS NOTICE, WORKING, COMPUT, INFLUSTRY OF ANA FUNCTION OR ANY ANT OF OTHER COMMERCIAL DAMAGE-SOH ORS-B, ANY IF SUCH PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO UMLIFY FOR DEATH OR PERSONAL INFLUSTRY FRODURING FROM SUCH PARTY'S NOGENCE TO THE EXTENT APPLICABLE LAW PRIORDED SUCH LIMITATION. SOME JURBSIC ITEMS ARE NOT ALLOW THE EXCLUSION OR LIMITATION OR INCIDENTAL OR CONSULNIAL DAMAGE IS, SO THIS EXCLUSION AND LITIA COMPANY NOT APPLY TO YOU. 10. J.S. GOVERNMENT END USERS.

the Covered Code is a "commercial item" as that item is defined in 48 C.I.R. 2.101 (Oct. 1985), consisting of commercial computer software and "commercial computer software documentation," as such items are used in 48 C.I.R. 12.212 (Sept. 1985). Constellen, with 48 C.I.R. 13.212 and 49 C.I.R. 227.206-1 through 227.7202-4 June 1985, at U.S. Government End Users acquire Covered Code only those rights set forth herein.

11. MISCELLANEOUS.

This license represents the complete agreement concerning support former interest, which may provide or this License is hard to be responsible, such that the plan shall be reformed only by the extent necessary to make it authorization. The license shall be governed by California laws provisions expected in the extent applicable law. If any provider otherwise, excluding its conditional provisions, with respect to results in nominal local one party is a dealer of, or an entity characterised or registered to do business in the United States of America, any other arising relating to the License shall be subject to the satisfaction of the Federal Court of the Northern District of California, with various having in Santa Clara County, California, with the leading party responsible for owners, including without limitation court cases and reasonable attorney fees and expenses. The application of the United States Convention on Contracts for the International Sale of Goods is exclusively excluded. Any law or regulation which

provider that the language of a contract shall be construed against the dealer shall not apply to this license.

1. RESPONSIBILITY FOR CLAIMS.

As between Initial Developer and the Contributors, each party is responsible for claims and damages arising, directly or indirectly, out of the utilization or rights under his license and You agree to work with must Developer and Contributors to distribute such responsibility on an equitable basis. Nothing herein is lender or shall be deemed to constitute any omission of facility.

1. MULTIPLE-LICENSED CODE.

Initial Developer may designate portions of the Covered Code as Multiple Licensed. Multiple Licensees that the Initial Developer shall be you to fill no portions or the Covered Code under Your choice of the MPL or the alternative licenses, I any, specified by the Initial Developer in the he described in Exhibit A.

EXHIBIT A - Mozilla Public License.

The contents of this are subject to the Mora Public License Version 1.1 (the "License"); you may not use this file except in compliance with a License. You may obtain a copy of the License at http://www.mora.org/MP/Software distribution under the license is distributed on an "AB 82" back, WITHOUT WARRANTY OF ANY KIND, either express or implied. See the License for the specific language governing rights and limitations under the License.

The Original Code is

the Initial Developer of the Original Code is ____ Positions assessed by ____ are Copyright (G) ____ A Rights Reserved.

Contributor(s)

Alternatively, the contents of this file may be used under the terms of the ____ license (the [____] License), in which case the provisions of [____] License are applicable instead of those stores, if you wish to allow use of your version of this file only under the terms of the [____] License are not to allow others to use your version of this file under the MPL. Indicate your section by selecting the provisions above and replace them with the notice and other provisions required by the [____] License. If you do not delete the provisions above, a resident may use your version of this file under either the MPL or the [____] License.

(HO) : The text of this Exhibit A may differ slightly from the text of the notices in the Source Code files of the Original Code. You should use the text of this Exhibit A rather than the text found in the Original Code Source Code for Your Modifications

The Independent JPEG Group's JPEG Software

The software included in this product contains copyright and software that is licensed under the J-1.5 license.

- JPEG license

Case project. Generating Outline: Ostengi, 1 b/pog

This distribution contains the sixth public release of the Independent JPOG Group's free JPOG software. You are welcome to send to Belize this software and to use it for any purpose, subject to the conditions under LEGAL ISSUES, below.

Serious years of this software (particularly those incorporating it into larger programs) should contact L.G. at (pag-InfoBunet u, not to be added to our electronic mailing is... Making list members are routed of updates and have a chance to participate in technical discussions, etc.

This software is the work of Tom Lama, Philip Gladstone, Jim Joucher, Lee Crocker, Jalan Mingullon, Las Chiu, George Philips, Davide Road, Guco Volbading, Sel Weijers, and other members of the Independent JPEG Group.

LIG is not articles with the official SEC J-IG standards committee.

LEGAL ISSUES

In plain English:

1. We don't promise that this software works. But if you find any buys, please et us know!

2. You can use this software or whatever you want.. You don't have to pay us.

3. You may not prepare that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that you've used the LOG code.

In legalese:

The authors make NO WARRANTY or representation, other excess or implied, with respect to this software, its quality, accuracy, merchantability, or finance for a particular purpose. This software is priced "AS IS", and you, its user, assume the entire risk as to its quality and accuracy.

This software is copyright (C) 1891-1986. Thomas G. Lane. All Rights Reserved except, as specified below.

Permission is hereby granted to use copy, modify and distribute this software (or portions thereof for any purpose, without law, subject to these conditions:

(1) If any part of the source code for this software is distributed, then this README tells must be included, with this copyright and no warranty notice, neither; and any additions, deletions, or changes to the original files must be clearly indicated in accompanying documentation.

(2) If only executable code is distributed, then the accompanying documentation must state that, "the software is based in part on the work of the Independent TEO Group".

(i) Permission or Use of this software is granted only if the user accepts full responsibility for any undesirable consequences, the authors accept NO. LIABILITY or damages of any kind.

These conditions apply to any software derived from or based on the UG code, not just to the unmodified library. If you use our work, you ought to acknowledge us.

Permeation is NOT granted for the use of any KG author's name or company name in advertising or publicly relating to this software or products derivative from it. This software may be referred to only as "the independent JPEG Group's software".

We specifically permit and encourage the use of this software as the basis of commercial products, provided that all warranty or liability claims are assumed by the product vendor.

and2mre is included in this distribution by permission of L. Peter Deutean, role proprietor of a copyright holder, Aladin Enterprises of Merlo Park, CA

an&er.c is NO I covered by the above copyright and conditions, but instead by the usual clear button terms or the free Software Foundation pricing poly, that you must include source code if you reabish but it. See the file anal2kno for full details; However, show anal2kno is not needed as part of any program generated from the UC code, this does not limit you more than the foregoing paragraphs do.

The JPR configuration options “contigure” was produced with GNU Abuoon. It is a copyright by the first Software (recirculation) or is merely distributionable. The same holder for its supporting protocols pointing guess, contigure, Airbnb, Iran, Any, And/or support protocol. In all will say, a copyign by VULU but is also merely distributionable. It appears that the arithmetic coding option of the JPEG space is powered by patents owned by IBM, AT&T and Mitsubishi. Finance arithmetic coding cannot legally be used without noting one or more economics. For this reason, support for arithmetic coding has been introduced from the first JPR software. Since arithmetic coding provides only a marginal gain over the anticipated Huffman needs, it is unlikely that very many implementations will support it. So rather as we aware, there are no patent realizations on the remaining outlook.

The UG distribution formerly included code to read and write GIF fee. To avoid enlargement with the Unive LZW percent, GIF reaching support has been removed altogether, and the GIF writer has been simplified to produce uncompressed GIFs. The technique does not use the LZW algorithm, the resulting GIF files are larger than usual, but are randomized by all standard GIF disorders.

We are required to state that

The Practice Interchange Formation is the Copyright property of ComputServe Incorporated. GFirent is a Service Mark property of ComputServe Incorporated.

T-Kernel License

- This Product uses the Source Code of T-Kernel under T-License granted by the T-Engine Forum(www.t-engine.org)

T-License [License Agreement for Source Code of T-Kornol]

established by T-Engine Forum

on January 23, 2004

issued on December 21, 2008

revised on March 24, 2009

Article 1. Scope of License Agreement

1. This License Agreement sets forth copyright and the terms and conditions of use applicable to the source code of T-Kernel distributed by T-Engine Forum and any derivative work created herein from.

Article 2. Definition

1. "T-Kamel" means a real-time operating system controlled and distributed by T-Engine Forum on behalf of the copyright holder thereof.

2. "Source Code" means a source program, including related comments and documentations, for the T-Kerns and the Robert Source Code definition in Article 3.6 which is registered with T-Engine Forum

3. "Hardware-dependent. Part" means the part of the Source Code which depends on hardware and needs to be charged when the Source Code is ported and occurred on the target hardware, and is designated and saturated as such part.

4. "Compiler-dependent Part" means the part of the Source Code which depends on controller and needs to be changed when the Source Code is posted and occurred on the target hardware, and is designated and accepted as such part.

5. "Header He" means the part of the Source Code which contains definitions necessary to develop application programs.

6. T-Engine Hardware* means the Hardware which is manufactured in accordance with the T-Engine Hardware specifications of the pT-Engine Hardware specifications issued by T-Engine Forum, and registered with T-Engine Forum.

7. "Similar Hardware to T-Engine Hardware" means any hardware including software which emulates hardware other than that defined in Article 2.8 above, on which the T-Kernel can be operated.

8. "Ported Source Code" means a source program produced from the Source Code by modifying only its Hardwaredescendent Part endor Compiler-dependent Part to enable it to be operated on the Engine Hardware or the Similar Hardware, of Engine Hardware. The Ported Source Code which is registered with 1 Engine Forum shall not be included in the Source Code.

9. "Modified Source Code" means a source program modified from the Source Code for the purpose of improving its performance, increasing or decreasing its function, and the like. The Period Source Code shall not be included in the Modified Source Code.

10. "Binary Code" means an executable code form, which is created by correcting programs, which include all or part of the Source Code on the Modified Source Code.

11. "Derivative Work" means the Modified Source Code on the Binary Code.

12. "Emodoss Product" means any product which operates with executable code form of the Source Code, the Modified Source Code or the Binary Code loaded on its hardware.

13. "End Use" means a consumer who uses the Encoded Product.

14. "System Developer" means any person who develops the Embedded Product by itself or has a third party develop the same, and provides, whether with or without payment, the End User with the Embedded Product.

15. *Distributor of Modification: means any person who produces the Meclined Source Code and, whether with or without payment, distributes he same to any third party.

16. "Patch for Modification" means a difference, program, system, or the file in order to create the Modified Source Code from the Source Code on the Binary Code format.

17. "Vicarious Execution of Patch Processing" means vicarious execution service to create the Modified Source Code applying the Patch for Modification to the Source Code or the Binary Code (new).

18. "Source Code User" means a person who uses the Source Code.

19. "Distribution" means any of the following acts:

20. to transmit a work to a large number of specific persons through the Internet communication, broadcasting, and the like;

21. to transmit a work to the general public through the internet communication, broadcasting, and the like automatically in response to a request, from the public; and

22. to distribute a copy of a work to the general public or a large number of specific persons.

Article 3. Copyright

1. The copyrights of the Source Code shall be owned by Ken Sakamura.

Article 4. License of Source Code

1. As provided for in this Article, T-Engine Forum shall provide, and grant a license to use, the Source Code less of charge to any person who has taken the necessary procedure for registration as prescribed by T-Engine Forum and agreed to the T-License.

2. The Source Code shall be distributed exclusively by T-Engine Forum. Any person who obtains the Source Code under Article 4.1 above shall not make any no Distribution of the Source Code.

3. In accordance with the license granted under Article 4.1 above, the Source Code User may perform the following acts:

4. to copy and/or modify the Source Code provided by T-Engine Forum hereunder for its own research, development and the like

5. To run the Source Goods provided by I Engine Forum hereunder for its own research, development and the like.

6. to run the Source Code modified in accordance with the provision of Article 4.8 (1) above for its own research, development and the like.

7. to distribute the Binary Code created from the Source Code provided by H-rgine Forum Elseunder or from the Source Code modified in accordance with the provision of Article 4.3 (1) above.

8. In accordance with the license granted under Article 4.1 above, the System Developer may perform the following acts:

9. to perform any and all acts set forth in the Article 4.3 above.

10. to develop and manufacture the Embedded Product containing the Binary Code, and, whether with or without payment, provides the End User with the same and make the Binary Code available to the End User on the Embedded Product.

11. The Source Code User and the System Developer shall be obligated to give a notice that the Source Code is used, in such a way as separately specified by T-Engine Forum, when they use the Source Code or the Binary Code, or make the Binary Code available for the End User on the Encoded Product.

Article 5. Distribution of Modified Source Code

1. Any of A members of T-Engine Forum may become the Distributor of Modification by cleaning the spromal of T-Engine Forum through the registration procedure as please based by the Forum presented that only the department of the A member which has taken the registration procedure may distribute the Modified Source Code in such a way as provided for in the Article as long as it hence the Anememberships.

2. The Distributor of Modification may create the Modified Source Code based on the Source Code provided by T-Engine Forum and the Patch for Modification to be applied to create such Modified Source Code from the Source Code.

3. The Distribution of Modification shall, prior to the distribution, Inform T-Engine Forum of and register a name and description of the Modific Source Code in such a way as specified by T-Engine Forum.

4. The Distributor of Modification shall determine the name of the Modified Source Code subject to the rules separately established by I-Engric Forum and publish an appropriate notice as required by the rules on the Patch for Modification and the Modified Source Code.

5. The Distributor of Modification may distribute the Modified Source Code to a third party, whether with or without payment, provided that the Distributor of Modification shall take the necessary measures to prohibit the third party from making the no. Distribution of the Modified Source Code.

6. Developer with the Patent for Modification. Provided, however, that the Distributor of Modification shall be obliged to confirm that the System Developer is the Source Code User duly licensed under Article 4.1.

7. The Distributor of Modification may perform the Vizarious Execution of Patch Processing for the System Developer.

8. The System Developer shall not distribute the Modified Source Code in further modified form to any third party as a stand-alone software product.

9. The System Developer may under the same obligation as interested in Article 4.5, make the Embedded Product available for the End User through use of the Patch for Modification distributed by the Distributor of Modification or the Derivative Works obtained through the Vicarious Execution of Patch Processing.

Article 6. Distribution and Registration of the Ported Source Code

1. The Source Code User and the System Developer may whether with or without change, distribute to any third party only the following parts of the Paved

Source Code on the T-Engine Hardware or the Similar Hardware to T-Engine Hardware:

1. The Hardware dependent Port and/or Compiler dependent Port; provided that the Source Code Laser and the System Developer shall Inform T Engine Forum, and T Engine Forum may publish, a method for distributing said Parkey to third parties.

2. The Header File, provided that the Header File shall be distributed together with the Binary Code of the Ported Source Code.

3. Any member of T Engine Forum may request T Engine Forum to register and distribute, as an original source code for T-Kernel, the Forced Source Code on the T Engine Hardware or the Similar Hardware to T Engine Hardware.

4. Any member of T-Engine Forum who requests the distribution mentioned in the preceding paragraph shall access to the following conditions:

5. The member shall confirm that the object hardware is the T-Engine Hardware or the Similar Hardware to T-Engine Hardware.

6. The member shall provide I-Engine Forum with a complete set of operational environment for the object hardware and I-Korol tree of charge when requesting the distribution.

7. The member shall submit test results of the Period Source Code to Engine Forum when requesting the distribution.

8. In the event that T-Engine Forum accepts the request mentioned in Article 0.2, T-Engine Forum shall register and distribute the Ported Source Code as the Source Codes for I-Kerms. Provided, however, that the Ported Source Code may be installed in the same way as the Modified Source Code until the time or registration hereunder.

9. The provision set forth in Article 3 shall apply to the Period Source Code registered in accordance with this Article.

Article 7. Use for Other Purpose

1. Any use of "no Source Code," no Modified Source Code or the Ported Source Code other than those stipulated in Articles 4, 5 and 6 shall be subject to the prior approval of T-Engine Forum.

Article 8. Limited Warranty

1. Engine Forum and the copyright holder of the Source Code warrant that the Source Code does not infringe third party's copyrights. Provided, however, that the Engine Forum and the copyright holder of the Source Code make no warranty as to the Hardware dependent Part and/or Compiler dependent Part act forth in Article 6.2 in the Ported Source Code by any third party.

2. Neither I Engine Forum nor the copyright holder of the Source Code warrants that the Source Code will be for any particular purpose of the Source Code User.

3. Neither T-Engine Forum nor the copyright holder of the Source Code warrants that the Source Code does not merge any third party's industrial property rights in no event shall T-Engine Forum and the copyright holder of the Source Code be liable for any dispute which may arise between the Source Code User and a third party in connection with the third party's industrial property rights.

Article 9. Indemnity

1. Neither T-Engine Forum nor the copyright holder of the Source Gate shall be ranks for any damages (including, but not limited to, damages resulting from loss of profit, business interruption, loss of business information or any other exceptional damage) arising out of use or impossibility of use or the Source Gate, even if T-Engine Forum and the copyright holder have been informed of the possibility of such damages.

Article 10. Breach of Agreement

1. In case that T-Engine Forum considers that this License Agreement is breached or that the popularization of T-Kernel is obstructed, T-Engine Forum shall take measures to correct such breach or such obstruction, take measures on the ground of copyright infringement, or take any other necessary measures against the breaching person or the obstructing person, regardless of whether or not the said person is a member of T-Engine Forum.

2. In case of breach of this License Agreement by a member of 1 Engine Forum, 1 Engine Forum may take appropriate measures against the member; for example, the member is disqualified from membership, depending on what kind of breach has been committed by it.

3. Any legal dispute which may arise in relation to any breach of this License Agreement shall be subject to the exclusive jurisdiction at the Tokyo District Court.

Article 11. Governing Law and Language

1. This License Agreement shall be governed by end interpreted under the laws of Japan.

2. This License Agreement is executed in both Japanese text and English text provided that the Japanese text shall govern the interpretation and performance of this License Agreement.

Apache License 2.0

Component Name License URL

rDNSResponder_conjour/Apache_License 2.0 http://www.apache.org/licenses/LICENSE-2.0

TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION

"License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document. "Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License.

Legal Entity shall mean the union of the acting entity and all other entities that contract, are controlled by, or are under common control with that entity, or the purposes of the action, control means in the power, order or indirect, to cause the direction or management of such entity, whether by contract or otherwise, only ownership of the percent 15% or more of the outstanding shares, or its beneficial ownership of such entity.

You for "Your" shall mean an individual or legal entity exercising penalties granted by this License. "Source form shall mean the preferred form for making modifiers, including but not limited to software source code, documentation source, and configuration files."

Object form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled object code generated documentation, and provisions to other media types.

Work" shall mean the work of authorship, whether in Source or Object form, made available under the License, as indicated by a copyright notice that is reputed or attached to the work (an example is provided in the Appendix below).

Derivative Works shall mean any work, whether in Source or Closed form, that is based on (or derived) from the Work and for whom the editorial revisions, citations, elaborations, or other modulators represent, as a notice, an original work or authorship. For the purposes of this license, Derivative Works shall not include works that remain separately from, or mostly link for him, by paying to the Interests of the Work and Derivative Works thereof.

"Contribution" shall mean any work of a membership, including the original version of the Work and any modifications on each other to their Work or Derivative Works (thereof, that is intermediately utilized to Donator for inclusion or the Work by the copyright owner or by an individual or Legal Entity authorized to submit on behalf or the copyright owner). For the purposes of this definition, "Submitted" means any form or electronic, verbal, or written communication sent to the Licitor or its representatives, including but limited to communication on electronic and logical lists, source code control systems, and issue tracking systems (see are managed by, or by behalf of, the Donator for the purposes of interacting and improving the Work, but involving communication that a company's marker or otherwise has been issued in the following material of the Donator and any individual or Legal Entity or behalf of whom a Donator has been received by Member and associates may be incorporated within the Work.

1. Grant of Copyright License: Subject to the terms and conditions of the License, each Contributor hereby grants to your perpetual execution, non-exclive, no charge, royalty-free, irreversible copyright licenses to reproduce, prepare Derivative Works of public display, publicly perform, subsidiaries, and distribute the work and each Derivative Works in Source or Object Items.

2. Grant of Patent License: Subject to the terms and conditions of a License, each Contributor hereby grants to You's perpetual consideration, non-exchange, re-discharge, repayment, irreversible patent orders as amended in this secondary patent license to make, have means, etc., after to sell, and I must and otherwise transfer the Work, which such License applies only to these patent claims described by such Contributor that are necessarily infringed by their Contributions' act or by combination of their Construction will with the Work to which such Contributions will be issued. If you institute patent litigation against any entity, protecting or promotes on counterarm in a law Act, alleging that the Work or a Construction incorporated within the Work constitutes direct or contribution point infringement, then any patent licenses granted to You under the License for that Work shall terminate as of the date such litigation is filed.

3. Collectibution. You must reproduce and distribute copies of the Work or Derivative Works thereof in any medium, with or without modifications, and in Source or Object form, provided that you meet the following conditions:

(a) You must give any other recipients of the Work or Derivative Works a copy of the License, and

(b) You must cause any modified lies to carry prominent notices stating that You changed the lies; and

(4) You must lead, in the Source form of any Derivative Works that you distribute all copyright, patent, trademark, and attribution notices from the Source form of the Work, excluding those notices that do not persist to any part of the Derivative Works; and

(M) If the Work section is "NOTICE" and be as part of this distribution, over any Derivative Works has. You constitute must include a redable copy of the utilisation notices contained within such NOTICE. He, excluding notes notice that do not perform to any part of the Derivative Works, in all end one of the following places: within a NOTICE but the distributed as part of the Derivative Works within the Source form or documentation. It provided along with the Derivative Works, or, within a display generated by the derivative Works. In terms of such third party notices normally appear. The contracts of the NOTICE are for interest and purposes only and do not modify the license. You may act as Your own utilisation notices within Derivative Works has. You distribute, alongside or an instrument to the NOTICE text, from the Work, provided that each electronic distribution rules cannot be construed as modifying the license.

You may add Your own expudige statement to Your modifications and may provide conditional or different license terms and conditions for use, reproduction, or distribution of Your modifications, or for any such Cherlier Works as a whole, provided Your use, reproduction and distribution of the Work otherwise complex with the conditions stated in this License.

1. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intent only submitted for inclusion in the Work by You to the User(s) shall be under the terms and conditions of this License, without any additional terms or conditions. Nowithstanding the above, nothing herein shall supersede or modify the terms of any separate license agreement you may have courted with a license regarding such Contributions.

2. Trademarks: This License does not grant permission to use the trade names, trademarks, service marks, or product names of the Licensor, except as required for reasonable and customary use in describing this origin of the Works and reproducing the content of the NOTICE 1a.

3. Disclaimer of therapy. Unless required by application or agreement to in writing, License provides the Work and each Contributor provides to Contributions on an "AS IS" BASE, WITHOUT WARRANTIES OF CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NONARRIEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of using or redistributing the Work and assume any risks associated with Your exercise of permissions under the License.

4. I believe it is easily in no act and under no legal theory, whether in line (including engineering, contract, or otherwise, unless required by applicable law (such as delicate and greedy contingent act) or agreed to in writing and any Contributor be taken to you for damages, including any claim, indirect, special, incidental or consequential damages of any character arising as a result of this License or out of the use or reality to use the Work (including but not limited or damages for loss or goodwill, work, language, computer failure or malfunction, or any etc all other commercial damages or losses), even in such Contributor has been adults of the possibility of such damage.

5. Accepting Warranty or Additional Liability, While distributing the Work or Derivative Works thereof, You may choose to offer and charge a fee for, accordance of coupon, warranty, indemnity, or other facility obligations and/or rights compliant with his License. However, in accepting such obligations, You may pay any on Your own behalf and on Your sole responsibility, not on behalf of any Contributor, and only if You agree to Indemnity, defend, and hold each Contributor unless for any facility incurred by or claims asserted against, such Contributor by reason or your accepting any such warranty or additional liability.

END OF TERMS AND CONDITIONS

APPENDIX How to apply the Apache License to your work.

To apply the Apache license to your work, obtain the following complete ration, with the fields enclosed by brackets [1] replaced with your own Identifying Information (Don't include the bracket). The text should be enclosed in the appropriate comment syntax for the file format. We also recommend that a file or class name and description or purpose be instructed on the same "printed page" as the copyright notice for easier identification within third-party archives.

Copyright (year) [name of copyright owner]

Licensed under the Apache License. Version 2.2 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.apache.org/licenses.io/NSH-2.0

Unless required by applicable law or agreed to in writing, software distributes under the License is distributed on an "AS IS" BASIS. WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, other expenses or Implicates. See the License for the specific language governing provisions and limitations under the License.

BZip2 License

This program, "bzip2", the associated library "lobzip2", and all documentation, are copyright © 1966-2007 Julian R. Seward. All rights reserved.

Component Name License URL

http://0.6:http://www.czp.org/

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Real distributions of source code must retain the above copyright notice, this list of conditions and the following disclaims:

2. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an advertisement in the product, documentation would be exceeded but it is not required.

3. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.

4. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOUWAL SHOULD BY THE AUTHOR AS'S AND ANY EXPRESS OR IMPLICIT WARRANTIES, INCLUDING, DO NOT LIMITED TO THE IMPUEST WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO PROCES FROM UN OF BUSINESS ITEMS (SEE) US\$ 100, DATA, OR OTHERS; OR BUSINESS IN RELIPTION NOW WHO GOULD AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Julien Sward [[e-mail]

http://bbvp2 version 1.0.5 of 10 December 2023

University of Illinois / NCSA Open Source License

Copyright (c): 1995-2007, The Board of Trustees of the University of Illinois All Rights Reserved.

Component Name License

Icer-2.0.5 University of Illinois / NCSA Open Source

I perd performance test

Mark Gates

May Trumas

Jr Ferguson

,on Dager

Feng Qin

Kevin Clobe

John Estabrook

National Laboratory for Applied Network Research

National Center for Supercomputing Applications

University of Illinois at Urbana-Champaign

http://www.nesc.ub.com/

Permiss on is hereby granted, free of charge, to any person obtaining a copy of this software (port) and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, subscribe, and/or sell capital of the Software, and to permit persons to whom the Software is furnished to do so, support to the following conditions:

Redistribution of source code must retain the above copyright notice, this list of conditions and the following disclaimers.

Redistribution in ordinary form must reproduce the above copyright notice, this list of conditions and the following disclosure in the documentation and/or other materials provided with the distribution.

Neither the names of the University of Illinois, NCNSA, nor the names of its contributors may be used to endorse or promote products derived from this Software without specific prior written permission. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE SHANKHIS O-WHOCH AN ABILLY, HUM-SS-O-A PART OUT AND KNESSEL AND KONING KINGHAM IN NCNT-PAVNI SHALL THE CONTRIBUTIONS OF COPYRIGHT HEREIN SHOULD BE TABLED FOR ANY CLAIM, DAMAGE OR OTHER LIABILITY, WHICH IT IS IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

PHP 3.01 License

The PHP License, version 3.01 Copyright (c) 1993 - 2010 The PHP Group. All rights reserved.

Component Name License URL

phc-5.2.17 PHP 8.01 Http://www.phc.net/distributions

Pod attribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met:

1. Reattributions of source code must rear the above copyright notice, this list of conditions and the following disclares.

2. Recistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. The name "PHP" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact [e-mail].

4. Products derived from this software may not be called "PHP", nor may "PHP" appear in their name, without prior written permission from groupAphp.net. You may indicate that your software works in conjunction with PHP by saying "Foo for PHP" instead of calling it "PHP Foo" or "phploc".

5. The PHP Group may publish related and/or new versions of the license from time to one each version will be given a distinguishing version number. Once covered code has been published under a particular version of the license, you may always continue to use it under the terms of this version. You may also choose to use such covered code under the terms of any subsequent version of the license published by the PHP Group. No one other than the PHP Group has this right to modify the terms applied to covered code created under the license.

6. Recistributions of any form whatever must retain the following acknowledgment: "This product includes PHP software, freely available from http://www.php.net/soc/arees"

THIS SOFTWARE IS PROVIDED BY THE PHP DEVELOPMENT TEAM AS IS AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BLT NOT LIMITED TO THE IMPLE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE PHP DIVE ORIENT THAT/OR THIS CONTRIBUTION SHALL ARE FOR ANY DIRECT, INDIRECT, INCIDENTAL, EXPOSITIVE, EXPOSIBLE, OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OTHER THAN ANY OBLIGATION OR QUANTITY OF THIS DRAWING OR OTHERS OR OTHERS ARE INGroup IN ANY WAY OUT OF THE USE OF THIS SOFTWARE. ANY PARTNERS OF THE POSSIBILITY OF SUCH DRAWING

The software console of voluntary contributions made by many individuals on behalf of the PHP Group. The PHP Group can be contacted via Email at [e-mail].

For more information on the PHP Group and the PHP project, please see http://www.php.hct. PHP includes the Zond Engine, freely available at http://www.zond.com.

zlib / libpng License

This software is provided "as-is", without any express or implied warranty. In no event, will the authors be held liable for any damages arising from the use of this software.

Component Name License URL

zib-1.28 zib/1bpg http://zib.net/

Copyright (C) 1985-2010 Jean-coup Gailty and Mark Adler

Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely subject to the following restrictions.

1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in this product documentation would be appreciated but is not required.

2. Altered source versions must be plainly marked as such, and must not be represented as being the original software.

3. This notice may not be removed or altered from any source distribution.

John Hub, Gally Mark Adler

joup467 p.org [e-mail]/comm.edu

The data format used by the zib library is described by FFCs (Request for Comments, 1957 to 1962 in the file http://www.let.org/for/fe 1963.txt) to format, rds18b1.txt pollute format and rds18b2.net (grip format).

Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Hanwha Techwin cases for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products.

The Eco mark represents Harwha Techwin's devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Correct disposal of batteries in this product

(Applicable in the European Union and other European countries with separate battery return systems.)

This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.

To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.

Head Office

6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si,

Gyeonggi-do, 463-400 Rep. of KOREA

Tel: [phone] Fax: [phone]

www.hanwha-security.com

Hanwha Techwin America

500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666

Toll Free +1.877.213.1222 Direct +1.201.325.6920

Fax [phone]

www.hanwhasecurity.com

Hanwha Techwin Europe

Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom

Tel [phone] Fax [phone]

www.hanwha-security.eu

Hanwha

Techwin

User Manual

ver.190228