ZGF648IR - Cooker ZANUSSI - Free user manual and instructions

Product Type	Gas Hob (Built-in)
Brand	Zanussi
Model	ZGF648IR
Number of Burners	4 (1 Rapid, 2 Semi-rapid, 1 Auxiliary)
Burner Power (Natural Gas G20)	Rapid: 3.0 kW, Semi-rapid: 2.0 kW, Auxiliary: 1.0 kW
Burner Power (LPG)	Rapid: 2.8 kW, Semi-rapid: 2.0 kW, Auxiliary: 1.0 kW
Gas Connection	G 1/2"
Gas Type	Natural Gas G20 (20 mbar) / LPG (30 mbar)
Electrical Supply	230 V ~ 50 Hz
Appliance Class	3
Hob Dimensions (W x D)	580 x 510 mm
Cut-out Dimensions (W x D)	560 x 480 mm
Pan Supports	Cast iron, removable for cleaning
Ignition	Automatic spark ignition (also manual without electricity)
Safety Features	Thermocouple flame failure device on each burner
Control Knobs	Front-mounted, easy to operate
Cleaning	Warm soapy water; avoid abrasive cleaners
Maintenance	Periodic check of gas supply and injectors
Optional Accessory	Glass lid (sold separately)
User Manual Languages	English, Russian, and others available for download
Warranty	European guarantee, subject to terms

Frequently Asked Questions - ZGF648IR ZANUSSI

How do I light the burners on the Zanussi ZGF648IR?

Push the relevant knob down and turn it anti-clockwise to the maximum position. For models with thermocouple, keep the knob pressed for about 5 seconds after lighting to activate the safety device. If electricity is unavailable, approach the burner with a flame.

What should I do if a burner does not light?

Check that the burner cap and crown are correctly positioned and clean. Ensure the ignition electrode is clean. If the burner still does not light after 15 seconds, release the knob, turn it off, wait one minute, and try again. If persistent, contact Service.

Can I use liquefied petroleum gas (LPG) with this hob?

Yes, the hob can be adapted to LPG (butane/propane) by replacing the injectors and adjusting the minimum flame setting. Refer to the installation section for detailed instructions. Use the correct injectors from the supplied set.

What are the dimensions of the Zanussi ZGF648IR hob?

The hob dimensions are 580 mm width and 510 mm depth. The required cut-out size is 560 mm x 480 mm. Ensure a minimum distance of 55 mm from the rear wall and 100 mm from side walls.

How do I clean the hob and burners?

Disconnect from electrical supply before cleaning. Remove burner caps and crowns and wash in warm soapy water. Wipe the hob top with a soft cloth wrung in warm soapy water. Avoid abrasive cleaners, steel wool, and bleach. For stainless steel, use a proprietary stainless steel cleaner.

Is it safe to use the hob with a lid?

The hob can be fitted with an optional glass lid (sold separately). Always ensure all burners are off before closing the lid. Wipe off any splashes before opening. Do not use the lid for any purpose other than covering the hob.

What type of gas connection does the hob require?

The hob has a G 1/2" gas connection. For natural gas, the supply pressure should be 20 mbar (G20). For LPG, 30 mbar. Use a fixed connection or flexible stainless steel pipe compliant with local regulations.

How do I install the Zanussi ZGF648IR into a worktop?

Cut an opening of 560 x 480 mm. Apply the supplied sealing strip around the cut-out edges. Place the hob into the cut-out, centre it, and fix it with the provided screws. Ensure the hob is level and the seal is compressed. For detailed steps, refer to the 'Building in' section of the manual.

What safety features does the hob have?

Each burner is equipped with a thermocouple that cuts off the gas supply if the flame goes out. The hob also has automatic spark ignition. Children must be supervised. Do not attempt repairs yourself; always contact an authorized Service Centre.

What should I do if the control knobs become stiff?

If the control knobs are difficult to turn, contact your local Service Force Centre. Do not force them. Regular cleaning around the knobs can help prevent stiffness.

USER MANUAL ZGF648IR ZANUSSI

Thank you for selecting our appliance Thank you for selecting our appliance

We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance.

Contents

For the User

Important safety information .... 5

Operation 7

Using the hob correctly 8

Cleaning and Maintenance 9

Service and original spare parts 20

European guarantee 20

For the Installer

Technical data 11

Installation 13

Adaptation to different types of gas 15

Electrical connection 16

Building in 17

Possibilities for insertion 19

Guide to Use the instructions

The following symbols will be found in the text to guide you throughout the Instructions:

Safety Instructions

Step by step instructions for an operation

Hints and Tips

Environmental information

This appliance complies with the following E.E.C. Directives:

• 2006/95 (Low Voltage Directive);
• 89/336 (Electromagnetical Compatibility Directive);
• 90/396 (Gas Appliances);
• 93/68 (General Directives)
and subsequent modifications.

MANUFACTURER: MANUFACTURER:

ELECTROLUX HOME PRODUCTS ITALY S.p.A.

Viale Bologna, 298

47100 FORLì (Italy)

English

Important safety information

This warnings has been given for the safety of you and others. We therefore ask you to carefully read the procedures of installing and using this appliance.

Installation

• The work of installation must be carried out by competent and qualified installers according to the regulations in force.
• Any modifications to the domestic electrical mains which may be necessary for the installation of the appliance should be carried out only by competent personnel.

During Operation

• This appliance has been designed for non professional purpose in private houses only. It is meant to cook edible foodstuff only and must not be used for any other purposes.
• It is dangerous to alter the specification in any way.
• For hygiene and safety reasons, this appliance should be kept clean at all times. A build-up of fats or other foodstuff could result in a fire.
• Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by unexperienced persons may cause injury or serious malfunctioning. Refer to your local Service Centre. Always insist on genuine spare parts.
• Ensure that all control knobs are in the OFF position when not in use.
• Should you connect any electrical tool to a plug near this cooking appliance, ensure that electric cables are not in

contact with it and keep them far enough from the heated parts of this appliance.

- If the appliance is out of order, disconnect it from the electric supply.

People Safety

• This appliance has been designed to be operated by adults and children under supervision. Young children must not be allowed to tamper with the controls or play near or with the oven.
• This appliance is not intended for use by children or other persons whose physical, sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction by a responsible person to ensure that they can use the appliance safely.
• Accessible parts of this appliance may become hot when it is in use. Children should be kept away until it has cooled.

About Installation, Cleaning and Manteinance

• It is mandatory that all operations required for the installation are carried out by a qualified or competent person, in accordance with existing rules and regulations.
• Disconnect the appliance from the electrical supply, before carrying out any cleaning or maintenance work.
• Ensure a good ventilation around the

appliance. A poor air supply could cause lack of oxygen.

• Ensure that the gas supply complies with the gas type stated on the identification label, placed near the gas supply pipe.
• This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. Particular attention shall be given to the relevant requirements regarding ventilation.
• The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed. Ensure that the kitchen is well ventilated: keep natural ventilation holes open or install a mechanical ventilation device (mechanical extractor hood).
• Prolonged intensive use of the appliance may call for additional ventilation, for example opening of a window, or more effective ventilation, for example increasing the level of mechanical ventilation where present.
• Once you removed all packaging from the appliance, ensure that it is not damaged and the electric cable is in perfect conditions. Otherwise, contact your dealer before proceeding with the installation.
• The manufacturer disclaims any responsibility should all the safety measures not be carried out.

Service

- Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by unexperienced persons may cause injury or serious malfunctioning. Refer to your local Service Centre. Always insist on genuine spare parts.

Environmental Information

●After installation, please dispose of the packaging with due regard to safety and the environment.
- When disposing of an old appliance, make it unusable, by cutting off the cable.

The symbol on the product or

on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

It is very important that this instruction book should be kept safely for future consultation. If the appliance should be sold or given to another person, please ensure that the booklet goes together with it, so that the new owner can know of the functions of the machine and also be aware of the warnings.

These instructions are only for the countries stated by the symbol printed on the front cover of this instruction book.

Operation

Hob burner control knobs

The symbols on the knobs mean:

● = no gas supply

aximum gas supply

minimum gas supply

For easier lighting, proceed before putting a pan on the pan support.

Lighting the burners

Mod. ZGF 648 IX

Push the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position.

Mod. ZGF 648 IR / ZGF 643 ITXC

After lighting the flame, keep the knob pushed down for about 5 seconds. This will allow the "thermocouple" (see figure - lett. D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted.

Then, check the flame is regular and adjust it as required.

If you cannot light the flame even after several attempts, check the "cap" and "crown" (see figure - lett. A, B) are in the correct position.

When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically.

In the absence of electricity, ignition can occur without the electrical device; in this case approach the burner with a flame, push the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position.

A - Burner cap
B - Burner crown
C - Ignition candle
D - Thermocouple

Do not keep the control knob pressed for more than 15 seconds.

If the burner does not light even after 15 seconds, release the control knob, turn it the "off" position and wait for at least one minute before trying to light the burner again.

The Hob Lid (available only for model ZGF 648 IX)

In order to make the appliance match with the kitchen design, a lid (not provided) can be fitted on the hob.

- The lid is meant to avoid dust to settle on the hob, when it is closed, and to collect splashes of oil or fat, when it is open. Do not use it for any other purpose.

To switch off burners

To put the flame out, turn the knob to the symbol (●).

• Always wipe off any splash of liquid before opening the lid.
• Always clean the lid from cooking residues before opening it or taking it off.

WARNING! The crystal lid can splinter when over heated. Always ensure all the burners are off before closing it.

Using the hob correctly

Practical hints

The burners

To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used.

Rapid Burner diameter 16-26 cm

Semi-rapid Burner diameter 12-22 cm Auxiliary Burner diameter 8-16 cm

• For easier lighting, proceed before putting a pan on the pan support.
• Use only pans or pots with flat bottom.

Three laboratory containers with bubbles and a crossed-out heating element, no text or symbols present

• Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite.
- If you use a saucepan which is smaller than the recommended size, the flame will spread beyond the bottom of the vessel, causing the handle to overheat.
- Prolonged cooking with potstones, earthenware pans or cast-iron plates is inadvisable. Also, do not use aluminium foil to protect the top during use.
- Make sure pots do not protrude over the edges of the cooktop and that they are centrally positioned on the rings in order to obtain lower gas consumption.
- Do not place unstable or deformed pots on the rings: they could tip over or spill their contents, causing accidents.

• Pots must not enter the control zone.
• If the control knobs become difficult to turn, please contact your local Service Force Centre.
• As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquid simmering.

Cleaning and Maintenance

⚠️ Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work.

The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.

This appliance cannot be cleaned with steam or with a steam cleaning machine.

The burners

• The burner caps and crowns can be removed for cleaning.
• Wash the burners taps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove.

●After cleaning, be sure to wipe dry with a soft cloth.
- Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food.

The Hob Top

- Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added. Avoid the use of the following:

• household detergent and bleaches;
• impregnated pads unsuitable for non-stick saucepans;
• steel wool pads;
• bath/sink stain removers.

- Should the hob top become heavily soiled, the following products are recommended:

- For stainless steel hobs use a

proprietary stainless steel cleaner.

- For other hobs use Hob Brite or Bar Keepers Friend.

- Do not leave acid or alkaline substances (e.g. vinegar, salt, lemon juice, etc.) on the cooktop.

Pan supports

To keep the pan supports in the right position, they are hooked to a couple of special hinges in the back of the hob.

Thanks to these hooks, you can lift the pan supports for easier cleaning, as shown in the picture.

To take the pan supports completely off the hob, proceed as shown in the picture.

The Ignition electrode

The electric ignition is obtained through a ceramic electrode with a metal electrode. Keep these components very clean, to avoid difficult lighting, and check that the burner crown holes are not obstructed.

Cast iron pan supports (ZGF 643 ITXC / ZGF 648 IR)

Caution!

When removing the cast iron pan supports, lift them up. Never turn the pan supports on the hinges since this could damage them.

Periodic Maintenance

Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted.

Line drawing of a hand using a ladder to lift a gas stove on a stovetop (no text or symbols)

Technical data

Burner gas power (natural gas G20-20 mbar)

Rapid burner 3,0 kW

Semi-rapid burner 2,0 kW

Auxiliary burner 1,0 kW

Category II2H3B/P

Gas supply natural gas G20 (2H) / 20 mbar

Gas connection G 1/2"

Electric supply 230 V\~50 Hz

Appliance class 3

Hob dimensions

Width 580 mm

Depth 510 mm

Cut out dimensions

Width 560 mm

Depth 480 mm

By-pass diameters

Burner ∅ By-pass in 1/100 mm.
Auxiliary 28 Semi-rapid 32 Rapid	42

Gas burners

	NORMAL REDUCED POWER POWER		NORMAL POWER
BURNER NATURAL GAS LPG			G20 (2H) - 20 mbar		(Butane/Propane) 30 mbar
	kW kW	g/h	inj. m100/mm	^3/h inj.100/mm		G30 G31
Auxiliary burner 1,0 0,33 70 0,095 50 73 71
Semi-rapid burner 2,0 0,45 96 0,190 71 145 143
Rapid burner	3,0(natural gas)2,8(LPG)	0,75	119	0,285	86	204	200

Gas burners G20 13 mbar - only for Russia

BURNER	NORMAL REDUCED POWER POWER		NORMAL POWER
	kW kW inj.	m	NATURAL GAS G20 - 13 mbar
			100/mm	^3/h
Auxiliary burner 0,9 0,33	80	0,095
Semi-rapid burner 1,4 0,45	105	0,148
Rapid burner 1,9 0,75	120	0,20

Installation

The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force.

The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed.

The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top.

Avoid installing the appliance in the proximity of inflammable materials (e.g. curtains, tea towels etc.).

THE MANUFACTURER WILL NOT ACCEPT LIABILITY, SHOULD ANY OF THE OTHER SAFETY INSTRUCTIONS INCORPORATED IN THIS BOOKLET OR THE REGULATION IN FORCE BE IGNORED.

Gas connection

Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combined with an oven.

IMPORTANT - To ensure a correct operation, a saving of energy and the long life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut G 1/2". Interpose the sealing between the components as shown in the picture. Screw the parts without forcing, adjust the connection in the required direction and tighten everything.

IMPORTANT

Once installation is complete, check the perfectseal of every pipe fitting, using a soapy solution, never a flame.

A) Ramp with ending nut
B) Seal
C) Adjustable connection

Adaptation to different types of gas

A. Injectors replacement

• Remove the pan supports.
• Remove the burner's caps and crowns.
• With a socket spanner 7 unscrew and remove the injectors (Fig. 1), and replace them with the ones required for the type of gas in use (see table 2).
• Reassemble the parts, following the same procedure backwards.

- Replace the rating label (placed near the gas supply pipe) with the relevant one for the new type of gas supply. You can find this label in the package of the injectors supplied with the appliance.

Should the feeding gas pressure be different or variable compared with the required pressure, an appropriate pressure adjuster must be fitted on the gas supply pipe, in compliance with the rules in force.

B. Adjustment of minimum level

To adjust the minimum level of the burners, proceed as follows:

• Light the burner.
- Turn the knob on the minimum position.
- Remove the knob.

- With a thin screwdriver, adjust the by-pass screw positioned in the centre of the gas tap control shaft (see Fig. 2). If changing from natural gas 20/13 mbar to liquid gas, completely tighten the adjustment screw in. If changing from liquid gas to natural gas 20 mbar, undo the bypass screw about 1/4 of a turn. If changing from natural gas 20 mbar to natural gas 13 mbar undo the bypass screw about 1/4 of a turn. If changing from liquid gas to natural

Mechanical diagram showing a valve assembly with a rotating component and a circular base (no text or symbols)

Fig. 1

gas 13 mbar, undo the by-pass screw about 3/4 of a turn.

- Finally check the flame does not go out when quickly turning the knob from the maximum position to the minimum position.

This procedure can easily be carried out, anyhow the hob has been positioned or built in the working top.

Diagram showing three mechanical components with arrows indicating direction, labeled Fig. 2 (no text or symbols on the diagram itself)

Minimum adjustment screw

Electrical connection

The appliance is designed to be connected to 230 V monophase electricity supply.

The connection must be carried out in compliance with the laws and regulations in force.

Before the appliance is connected:

1) check that the main fuse and the domestic installation can support the load (see the rating label);
2) check that the power supply is properly earthed in compliance with the current rules;
3) check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the furniture unit.

The appliance is supplied with a connection cable. This has to be provided with a proper plug, able to support the load marked on the identification plate. To connect the plug to the cable, follow the recommendation given in Fig. 3-a. The plug has to be fitted in a proper socket.

If connecting the appliance directly to the electric system, it is necessary that you install a double pole switch between the appliance and the electricity supply, with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current rules.

The connection cable has to be placed in order that, in each part, it cannot reach a temperature 50^ C higher than room temperature.

The brown coloured phase cable (fitted in the terminal block contact marked with "L") must always be connected to the network phase.

Remplacement of the voltage cable

The connection of the voltage cable to the appliance's terminal block is of type "Y". This means that its replacement requires the specific equipment of a technician. In this case, only cable type H05V2V2-F T90 must be used. The cable section must be suitable to the voltage and the working temperature. The yellow/green earth wire must be approximately 2 cm. longer than the phase wires (Fig. 3-a).

To open the terminal block and reach the terminals, proceed as follows:

• insert the point of a screwdriver into the visible protruding part of the terminal block;
• exert a light pressure and lift (Fig. 3-b).

Fig. 3-a

Diagram of a mechanical lever mechanism with a curved arrow indicating motion (no text or symbols)

Fig. 3-b

Building in

Fig. 4

A = Auxiliary burner

SR= Semi-rapid burner

R = Rapid burner

This hob can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in Fig. 4.

The edge of the cut out must have a minimum distance from the rear wall of 55 mm.

If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a minimum distance of 100 mm.

Hanging forniture units or hoods must be placed at 650 mm. minimum from the hob.

Fitting the lid

We recommend the lid hinge blockWe recommend the lid hinge block are fitted before installing the hobare fitted before installing the hob into the worktop.into the worktop.

To install the lid onto the hob, proceed as follows:

a. Remove the right and left hand grid blocks fitted to the back of the hob, by unscrewing the relevant screws (Fig. 5).

Fig. 5

b. Fit the lid hinge blocks onto the hob, using the original screws, ensuring that the relevant shims are fitted between the hinge blocks and the hob;
c. Fit the left hand lid hinge (marked S) into the hinge block (Fig. 6);
d. Carry out the same operation with the right hand lid hinge (marked D).

Adjusting the lid balance

To adjust the lid balance, turn clockwise or anti-clockwise the central screw of the right- and left-hand hinges (Fig. 7).

Diagram showing a mechanical assembly with a downward arrow indicating a process or alignment (no text or symbols present)

Fig. 6

Technical illustration of a mechanical assembly with a bolt and nut, showing a curved arrow indicating motion (no text or symbols)

Fig. 7

Fitting the hob to the worktop

The hob can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig. 8. To install the hob, proceed as follows:

1. Remove the pan supports, the burners caps and crowns and turn the hob upside down, taking care the ignition candles are not damaged in this operation.
2. put the relevant sealings, supplied with the hob, on the edges of the cut out, as shown in Fig. 9, taking care that the sealings meet without overlapping;
3. place the hob in the cut out, taking care of its centring;
4. fix the hob with the relevant screws (Fig. 10). The traction of the screws is able to trace the sealing, any excess of which can then be easily removed.

The edge of the hob forms a double labyrinth seal which provides a total guarantee against infiltration of liquids.

Dimensions are given in millimeters

Fig. 8

Fig. 9

Fig. 10

Possibilities for insertion

Kitchen unit with door

Proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in Fig. 11. The panel fitted under the hob should be easily removable to allow an easy access if a technical assistance intervention is needed.

Kitchen unit with oven

The hob recess dimensions must comply the indication given in Figs. 12 and 13 and must be provided with brackets to allow a continuous supply of air.

The hob's electric connection and the oven's one must be carried out separately, both for safety reasons and to allow the oven to be easily taken off the unit.

Fig. 11

a) Removable panel
b) Space for connections

Fig. 12

Fig. 13

Service and original spar Spar base and original spar

This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results.

Any repair work which needs to be carried out should be done with the utmost care and attention.

For this reason we recommend that for any problem you contact the dealer who sold it to you, or our nearest authorized Service Centre, specifying the nature of

the problem, the appliance model (Mod. More product number (Prod. No. Prod. No and the serial number (Ser. No. Seranked on the identification plate.

Original spareparts, certified by the product manufacturer and carrying this symbol are only available at our Service Centre and authorized spareparts shops. Electrolux

European guarantee

This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications:

• The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by production of a valid purchase document issued by the seller of the appliance.
• The appliance guarantee is for the same period and to the same extent for labour and parts as exists in your new country of residence for this particular model or range of appliances.
• The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred to another user.
• The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within the home, i.e. is not used for commercial purposes.
• The appliance is installed in accordance with all relevant regulations in force within your new country of residence.

The provisions of this European Guarantee do not affect any of the rights granted to you by law.

www.electrolux.com

Albania	[phone]	Rr. Pjeter Bogdani Nr. 7 Tirane
Belgique/België/Belgien	[phone]	Bergensesteenweg 719, 1502 Lembeek
Česká republika	[phone]	Budějovická 3, Praha 4, 140 21
Danmark	[phone]	Sjællandsgade 2, 7000 Fredericia
Deutschland	[phone]	Muggenhofer Str. 135, 90429 Nürnberg
Eesti	[phone]	Pärnu mnt. 153, 11624 Tallinn
España	[phone]	Carretera M-300, Km. 29,900 Alcalá de Henares Madrid
France	www.electrolux.fr
Great Britain	[phone]	Addington Way, Luton, Bedfordshire LU4 9QQ
Hellas	[phone]	4, Limnou Str., 54627 Thessaloniki
Hrvatska	[phone]	Slavonska avenija 3, 10000 Zagreb
Ireland	[phone]	Long Mile Road Dublin 12
Italia	[phone]	C.so Lino Zanussi, 26 - 33080 Porcia (PN)
Latvija	[phone]	Kr. Barona iela 130/2, LV-1012, Riga
Lietuva	[phone]	Ozo 10A, LT 08200 Vilnius
Luxembourg	[phone]	Rue de Bitbourg, 7, L-1273 Hamm
Magyarország	[phone]	H-1142 Budapest XIV, Erzsébet királyné útja 87
Nederland	[phone]	Vennootsweg 1, 2404 CG - Alphen aan den Rijn
Norge	[phone]	Risløkkvn. 2 , 0508 Oslo
Österreich	[phone]	Herziggasse 9, 1230 Wien
Polska	[phone]	ul. Kolejowa 5/7, Warszawa
Portugal	[phone]	Quinta da Fonte - Edificio Gonçalves Zarco - Q 35 -2774-518 Paço de Arcos
Romania	[phone]	Str. Garii Progresului 2, S4, 040671 RO
Schweiz - Suisse - Svizzera	[phone]	Industriestrasse 10, CH-5506 Mägenwil
Slovenija	[phone]	Gerbičeva ulica 98, 1000 Ljubljana
Slovensko	[phone]	Electrolux Slovakia s.r.o., Electrolux Domáce spotrebiče SK, Seberíniho 1, 821 03 Bratislava
Suomi	www.electrolux.fi
Sverige	[phone]	Electrolux Service, S:t Göransgatan 143, S-105 45 Stockholm
Türkiye	[phone]	Tarłabași caddesi no : 35 Taksim İstanbul
Россия	[phone]	129090 Москва, Олимпийский проспект, 16, БЦ "Олимпик"

Line drawing of a hand using a ladder to install a gas stove on a stovetop (no text or symbols)

Technical diagram of a mechanical assembly with a dial and nut, showing internal components without any text or symbols.

Рис. 2

Рис. 5

Technical diagram showing a mechanical assembly with a downward arrow indicating a process or alignment (no text or symbols present)

Рис. 6

Technical line drawing of a mechanical assembly with threaded fasteners and a curved arrow indicating motion (no text or symbols)

Рис. 7

Рис. 9