TFS14SL - Loudspeaker TIC - Free user manual and instructions

Product Type	Outdoor Rock Speaker
Brand	TIC
Model	TFS14SL
Category	Speaker
Driver Configuration	3-way full range
Woofer	8" injection molded PP cone with Butyl rubber surround
Midrange	5" injection molded PP cone with Butyl rubber surround
Tweeter	1" aluminum dome
Power Handling (Continuous/Peak)	200W / 300W
Impedance	8 ohms
Frequency Response	27Hz – 19kHz
Sensitivity @1W/1m	89dB ± 3dB
Dimensions (H x W x D)	18.5 x 21.5 x 18 in
Weight	45 lbs
Cabinet Material	Multi-layer composite (aerospace grade)
Grill Material	Aluminum
Weatherproofing	Teflon® sealed cabinetry, weatherproof design
Connector	Surface mount waterproof cable connector
Finish Options	Canyon (CN), Slate (SL), White Granite (WG)
Recommended Cable	SPC double insulated or burial spec; 16/18 gauge for 10-25 ft, 10/14 gauge for 25-100 ft
Warranty	1 year parts and labor (standard); extended options available

Frequently Asked Questions - TFS14SL TIC

Why is there no sound from the speakers?

Check that the speakers are connected to the cable correctly, the cable is connected to the receiver/amplifier, and the amplifier is powered on, not muted, and the correct channel (A or B) is selected. Also verify the volume and balance settings. If using a different source, test with a known working connection.

What should I do if only one speaker produces sound?

Check the balance control on your receiver. Swap the cable from the non-working speaker to a working channel. If it works, the issue is with the amplifier channel. If not, connect the working speaker's cable directly to the non-working speaker. If it works, the problem is in the original cable; otherwise, the speaker may be faulty.

How deep should I bury the speaker cable?

TIC recommends burying the cable 4 to 6 inches (10-15 cm) deep to protect it from accidental disturbance. Use a burial-rated cable (double insulated) for best results.

What gauge speaker cable should I use?

For runs of 10-25 feet, use 16 or 18 gauge 2-core cable. For longer runs (25-100 feet), use 10 or 14 gauge to minimize resistance. Double insulated or burial spec cable is preferred for outdoor installations.

How do I clean and maintain the speakers?

Regularly inspect the grill area and remove any dirt, twigs, or debris. Clean the cabinet with a mild detergent (e.g., dish soap) and water using a soft cloth or hose on low pressure. Avoid high pressure water or forcing water into the grill or acoustic ports.

Can I leave the speakers outside in winter?

Yes, but in very cold climates with heavy snowfall, you can place a plastic bag over the unit during prolonged inactivity or snow cover. The speakers are weatherproof but extra protection can help prevent ice build-up.

How do I ensure correct polarity when connecting?

Always connect + to + and – to –, or red to red and black to black, from your amplifier to the speakers. Incorrect polarity will cause poor sound quality and may damage equipment.

What is the difference between series and parallel wiring for multiple speakers?

Series wiring increases total impedance (e.g., two 8Ω speakers in series = 16Ω), reducing power. Parallel wiring decreases impedance (e.g., two 8Ω speakers in parallel = 4Ω), increasing power. Ensure your amplifier can handle the resulting load. A diagram is included in the manual.

What does the warranty cover?

TIC offers a standard 1-year warranty covering parts and labor. Extended 3- or 5-year warranties may be available through authorized dealers. Check your warranty card or dealer receipt for details. The warranty is void if the product is installed incorrectly or damaged.

How can I contact TIC for support?

You can reach TIC Corporation by phone at [phone] (SPX-OMNI), by email at [e-mail], or visit www.ticcorp.com for FAQs and additional resources.

USER MANUAL TFS14SL TIC

TFS14 & TFS15 "Pro" Outdoor Rock Speakers

Close-up of several irregularly shaped, textured mineral or rock fragments with no visible text or symbols.

TIC TFS14 & TFS15 Outdoor Rock Speakers Feature

• Weatherproof Design
• Teflon® sealed cabinetry
• Aluminum Grill
  • Full range 200W speaker system
  • 10" woofer driver
• 5" mid range driver
  • 1" aluminum tweeters
• Surge protected Revchem®
  • 8 Ohm Impedance
• Aerospace grade multi-layer composite cabinetry
• Surface mount waterproof cable connector
  • Finishes: Canyon (CN) Slate (SL) or White Granite (WG)

For your records...

Manufacturers Name:	TIC Corporation	Manufacture Contact:	www.ticcorp.com(800) SPX-OMNI
TIC Model Number:		Serial Number:
Dealers Name:		Dealers Contact:
Purchase Date:		Invoice/ Receipt Number:

We recommend you keep your sales receipt and warranty card together with this owners guide for safe keeping and future reference.

This TIC Exterior Audio Product Conforms to all applicable:

Directives

One World, TIC Recycles

Index...

Introduction 3

Component List 4

Pre-Installation 4

Connection Cable 5

Exterior Installation 5/6

Maintenance 7

Customer Service 7

Warranty 7

Trouble Shooting 9

Technical Specifications 10

Thank You for purchasing another high quality audio product from TIC Corporation. Please read the enclosed installation guidelines carefully and thoroughly to ensure years of trouble free service from your new TIC exterior audio products.

Carefully unpack your new TIC exterior product and save all packaging materials for possible future use. Check that your new TIC product contains all system parts detailed in the Components list. Do not attempt to operate, install or use your new TIC product if any components appear missing or damaged. If so, please notify TIC Corporation or your TIC Dealer as soon as possible.

!WARNING! to avoid possible suffocation or injury please keep all plastic bags away from children and pets.

Component List...

1x	Outdoor rock speakers
1x	Weatherproof speaker cable connectors (base of units)
1x	New product offer (enclosed with literature)
1x	Instruction Manual
1x	Warranty Card

Illustration of various items including a rock, open book, pen, and coiled wire (no text or symbols present)

Pre-Installation...

Need Professional Help?

Please read this owners guide carefully before installation. Failure to follow these instructions fully or incorrect installation may damage your new TIC products and any third party equipment used in your new system installation. This may also Void any warranty for your new TIC products. If you are unsure of your ability to fully understand and fully complete the installation of this TIC product, please consult a professional installer.

Note: TIC Corporation always recommends that you test your product and its components prior to exterior installation. Test your components near a mains power and, if required, receiver amplifier sources somewhere convenient, perhaps inside. Ensure all components are working smoothly and correctly before exterior placement, installation and operation.

Exterior Installation...

Before you begin the installation of your new TIC outdoor product, please carefully select the locations of your new TIC products.

In general;

1. Select a reasonably level surface for the installation of your new TIC outdoor speakers. For surface speakers this will prevent movement or excessive vibration during use. This will also ensure more uniform sound dispersion.
2. Ensure your new TIC outdoor speaker cables or power source if required, can easily reach your new speakers. Some people even pre-lay string as a guide ensuring that there are no obstructions or difficulties such as concrete paths or architectural feature impediments. While most if not all TIC outdoor speakers use and recommend burying the cable lightly 4-6 inches, if the cable is surface mounted you must make sure the cable is placed where it cannot be tripped over, pulled, abraded or crushed.
3. Do not place your TIC outdoor speakers in a depression or area where water pools or in the direct path of sprinklers.
4. Wherever possible avoid long term exposure of your new TIC outdoor speakers to chlorinated solvents, acids such as those often contained in fertilizers and other solvents which have the potential to eventually wear the components prematurely.
5. When installing either burial cable or TIC's in-ground outdoor speakers please be very aware of any submerged plumbing, piping such as sprinklers or irrigation and wiring already in existence.

A note on Speaker Cable;

TIC recommends the use of our SPC double insulated high quality speaker cable, however just about any reasonable speaker cable may be used including existing runs that may be in place. For standard 8Ω installations of 10 – 25ft., just about any 16/18 gauge 2 core cables can usually be used although we would prefer a double insulated or burial spec cable be used. For longer runs of 25 – 100ft. 10/14 gauge cable can be used however resistance down the line will become a contributing factor.

Please visit TIC Corporations website at www.ticcorp.com and review the Audio Installation Basics articles under Technical Resources for more in depth exterior audio and cable guidelines.

Cartoon illustration of a boy walking past a fence with a rock and plants (no text or symbols)

Run the cable.

Before actually sinking the cable, run the cable from your unit to the power source or amplifier. Ensure your cable run avoids any obstacles such as sunken sprinkler pipes or piping and electrical cable to your house. Once the cable runs are where you like them, connect your speakers and power source to ensure correct operation before sinking the cable. Disconnect the cable wire at both ends and continue.

An Important note on Polarity!

Pleasure proper polarity when connecting your new TIC outdoor speakers. This is very important and will result in poor sound reproduction and possibly equipment damage if not connected correctly. This is normally avoided by ensuring + to + and – to – or as sometimes color coded Red to Red and Black to Black from your amplified source to your speakers respectively.

Cartoon illustration of a person digging with a shovel, standing beside a fence and rocks (no text or symbols)

Allow 4" of cover

Once you have tested your cable run in step 3, it is time to sink the cable. 4-6" of cover is normally recommended to offset accidental disturbance, movement of the earth etc. but your specific onsite conditions will apply. Should you wish to secure the installation of your unit then simply clamp, by way of a "U" spike etc. the cable directly beneath the unit or you may use TIC's SPPSS Security Stake available as an optional extra.

Cartoon illustration of a person sitting on a bench with a tool, no text or symbols present

Connect to power source.

Reconnect the speakers and your receiver amplifier being careful to ensure correct "Polarity" matching.

Once connected properly, fill in all trenches, sit back and enjoy!

Illustration of a person relaxing on a lounge chair with plants and flowers in the background (no text or symbols)

Enjoy quality, outdoor product!

Disclaimer;

TIC Corporation will in no way be held responsible for the improper or unsecured installation of this product. Any and all damage arising from the installation or use of this product is the purchaser and final installer's sole responsibility.

Ma inte nance...

Occasional maintenance of your TIC products cannot hurt and may help greatly. Inspect the installation area regularly removing and twigs, dirt or particulate matter from impeding or building up around the output grill area. The units may be cleaned using very mild detergents like dishwashing liquid if desired. A hose with clean water may also be used but please avoid using high pressure or forcing water into the grill or acoustic ports.

In very cold climates with moderate to heavy snowfall an old trick from the major theme parks we supply world wide is to place a plastic bag over the unit for the winter or periods it may be not in use or under such snowfall.

Customer Service...

For any additional help please contact TIC Corporation at (800) SPX-OMNI, on line at www.ticcorp.com , or by email at [e-mail] where we would be happy to assist you at any time. Also please visit our website for FAQ (frequently asked questions) and full contact information.

Warranty Period...

TIC Corporation offers a full, UCC approved, one year full parts and labor warranty on all its products as standard however there are other 3 and 5 year warranties in use with various TIC authorized Dealers world wide. Please check your enclosed Warranty card or your Dealer receipt to find out which one applies to you. Also please note TIC Corporation General Terms & Conditions posted on our website at www.ticcorp.com for further information.

Installation Notes...

Please note series vs. parallel installation wiring choices below;

graph TD
    A["4Ω POWER AMPLIFIER"] --> B["16-OHM EFFECTIVE IMPEDANCE"]
    C["8Ω"] --> B
    D["10Ω"] --> B
    E["COMM (GROUND)"] --> B
    B --> F["8-OHM SPEAKER SYSTEM"]
    B --> G["4-OHM EFFECTIVE IMPEDANCE"]
    B --> H["8-OHM SPEAKER SYSTEM"]
    F --> I["8-OHM SPEAKER SYSTEM"]
    G --> J["8-OHM EFFECTIVE IMPEDANCE"]
    H --> K["8-OHM SPEAKER SYSTEM"]
    I --> L["8-OHM SPEAKER SYSTEM"]
    J --> M["8-OHM EFFECTIVE IMPEDANCE"]
    K --> N["8-OHM SPEAKER SYSTEM"]
    L --> O["8-OHM EFFECTIVE IMPEDANCE"]
    M --> P["8-OHM SPEAKER SYSTEM"]
    N --> Q["8-OHM EFFECTIVE IMPEDANCE"]
    O --> R["8-OHM SPEAKER SYSTEM"]
    P --> S["8-OHM EFFECTIVE IMPEDANCE"]
    Q --> T["8-OHM SPEAKER SYSTEM"]
    R --> U["8-OHM EFFECTIVE IMPEDANCE"]
    S --> V["8-OHM SPEAKER SYSTEM"]
    T --> W["8-OHM EFFECTIVE IMPEDANCE"]
    U --> X["8-OHM SPEAKER SYSTEM"]
    V --> Y["8-OHM EFFECTIVE IMPEDANCE"]
    W --> Z["8-OHM SPEAKER SYSTEM"]
    X --> AA["8-OHM EFFECTIVE IMPEDANCE"]
    Y --> AB["8-OHM SPEAKER SYSTEM"]
    Z --> AC["8-OHM EFFECTIVE IMPEDANCE"]
    AA --> AD["8-OHM SPEAKER SYSTEM"]
    AB --> AE["8-OHM EFFECTIVE IMPEDANCE"]
    AC --> AF["8-OHM SPEAKER SYSTEM"]
    AD --> AG["8-OHM EFFECTIVE IMPEDANCE"]
    AE --> AH["8-OHM SPEAKER SYSTEM"]
    AF --> AI["8-OHM EFFECTIVE IMPEDANCE"]
    AG --> AJ["8-OHM SPEAKER SYSTEM"]
    AH --> AK["8-OHM EFFECTIVE IMPEDANCE"]
    AI --> AL["8-OHM SPEAKER SYSTEM"]
    AJ --> AM["8-OHM EFFECTIVE IMPEDANCE"]
    AK --> AN["8-OHM SPEAKER SYSTEM"]
    AL --> AO["8-OHM EFFECTIVE IMPEDANCE"]
    AM --> AP["8-OHM SPEAKER SYSTEM"]
    AN --> AQ["8-OHM EFFECTIVE IMPEDANCE"]
    AO --> AR["8-OHM SPEAKER SYSTEM"]
    AP --> AS["8-OHM EFFECTIVE IMPEDANCE"]
    AQ --> AT["8-OHM SPEAKER SYSTEM"]
    AR --> AU["8-OHM EFFECTIVE IMPEDANCE"]

Basic Series/parallel/ combined diagram

Trouble Shooting...

Problem

No Sound

Please Check

• Check the speakers are connected to the cable correctly.
• Check the speaker cable is connected to the receiver amplifier correctly.
• Check the receiver amplifier is powered “on” at the mains, is not on “mute”, has no headphones attached and that the Channels used for the exterior speakers (usually A or B) is in operation.
• Refer to the owners guide that came with your receiver amplifier.
• Most initial problems are connectivity, please try a different connection cable to your outdoor speakers or equipment.

No Sound from one speaker

• Check the "balance" control on your receiver amplifier.
• Check all connections and cable to the inoperable speaker.
• 1. Disconnect the “working” speaker from the receiver amplifier connection/ channel. Switch the cord from the non-operating speaker from its current connection to the “working” speaker connection. If the speaker now works the problem is your receiver amplifier.
• 1. Reconnect as original. Remove the speaker cable at the “working” speaker directly and connect it directly to the non-working speaker. If the speaker now works the problem is somewhere in the original speaker cable.
• 1. If the speaker still does not work the problem is the speaker.

One speaker sounds distorted, lower volume or "different"

- Follow same procedure as above for "No Sound".

Treble or Bass

• Check the "tone" setting on your receiver amplifier.
• Adjust the Treble and Bass settings on your receiver amplifier.
• Check the connections carefully from the amplifier to your speakers and ensure correct Phase (+ to + and – to – accordingly). Poor sound replication is expected from a speakers or speakers out of polarity or phase.

Technical Specifications...

General Specifications TIC TFS14 & TFS15 Outdoor Rock Speakers
Woofer(s)	8" injection molded PP cone Butyl rubber surround
Mid Range	5" injection molded PP cone Butyl rubber surround
Tweeter	1" aluminum
Cabinetry	Multi-layer Composite
Grill	Multi-layer Composite
Frequency Response	27Hz – 19kHz
Sensitivity @1W/1m	89db ± 3db
Continuous/ Peak	200 / 300W
*Optional 70v system	Use TIC SP70vTA
Unit(s) Dimensions	TFS14: 18.5x21.5x18 in TFS15: 18.5x24x24 in
Unit(s) Weight	TFS14: 45 lbs TFS15: 51 lbs
Pack Dimensions	TFS14: 23x26x22 in TFS15: 22x28x26.5in
Pack Weight	TFS14: 48 lbs TFS15: 54 lbs

TIC Corporation engages in continual product research and development, new materials, production methods and design improvements. TIC Corporation therefore, reserves all rights to change or improve products specifications without notice.

TIC Corporation

15224 East Stafford Street

City of Industry, CA. 91744-4418 U.S.A.

Tel: [phone] (5 lines) Fax: [phone]

Email: [e-mail] WWW: www.ticcorp.com