55LP1M - Tracking LG - Free user manual and instructions

Product Type	55-inch LCD Monitor
Model	55LP1M
Panel	55 inches (139.7 cm) TFT LCD, Pixel Pitch 0.630 mm
Maximum Resolution	1920 x 1080 @60Hz (RGB1/RGB2/DVI)
Recommended Resolution	WSXGA 1920 x 1080 @60Hz
Horizontal Frequency	30 - 83 kHz
Vertical Frequency	56 - 85 Hz
Power Supply	AC 100-240V~ 50/60Hz 3.5A
Power Consumption (On)	350 W
Power Consumption (Sleep/Off)	≤ 3 W
Dimensions (W x H x D) - [1]	1375.4 x 943.2 x 320.0 mm (54.15 x 37.13 x 12.60 inches)
Dimensions (W x H x D) - [2]	1612.0 x 943.2 x 320.0 mm (63.46 x 37.13 x 12.60 inches)
Weight - [1]	68.5 kg (151.01 lbs)
Weight - [2]	72.9 kg (160.71 lbs)
Input Connectors	15-pin D-Sub, DVI-D, S-Video, Composite, Component, RS-232C
Audio Output	RMS 10W + 10W (R+L), Speaker Impedance 8Ω
Special Features	PIP/POP/PBP, Tile Mode (up to 4x4), Auto Configure, OSD Menu, Child Lock, RS-232C Control
Stand Range	-30° to +30°
Wall Mount	VESA compatible (optional)
Operating Temperature	5°C to 35°C
Storage Temperature	-20°C to 60°C
Accessories	Power Cord, D-Sub Cable, DVI-D Cable, Audio Cable, Remote Control with Batteries, Brackets

Frequently Asked Questions - 55LP1M LG

What should I do if no image appears on the screen?

Check that the power cord is properly connected and the power switch is on. If the power indicator is amber, the monitor is in power saving mode; move the mouse or press any key. If you see 'Out of range', adjust the PC's resolution to 1920x1080 @60Hz. If 'Check signal cable' appears, ensure the signal cable is connected and press the INPUT button to select the correct source.

How do I unlock the controls if 'Controls locked' message appears?

Press and hold the MENU button and the ▶ button simultaneously for several seconds on the front panel of the monitor (not the remote control) to unlock. This feature prevents unintentional OSD changes.

Why is the screen not full size when connected to a PC?

If the screen size is not full, go to PIP/POP/PBP menu and change to full screen mode. Also, you can adjust the aspect ratio using the ARC button on the remote control. For PC analog signals, press the AUTO button to automatically optimize the screen.

How do I adjust the screen position or remove vertical stripes?

For D-Sub analog signals, press the AUTO button to automatically adjust position, clock, and phase. If not satisfactory, use the OSD menu: go to SCREEN > Clock to minimize vertical bars, Phase to sharpen the image, and Position to move the screen.

What does the Tile Mode function do?

Tile Mode allows you to create a large video wall by connecting multiple monitors. You can set rows and columns (up to 4x4) and assign each monitor an ID in the SPECIAL menu. Use the RS-232C protocol to control them from a PC.

Can I use PIP/POP/PBP with any input source?

PIP is not supported in 480i, 576i, and 1080i modes. Refer to the compatibility table in the manual. For example, when the main screen is RGB1, the sub-screen can be AV or Component, etc. Use the PIP, POP, or PBP button on the remote to switch modes.

How do I clean the monitor safely?

Unplug the power cord. Clean with a soft, dry cloth to avoid scratching. Do not use water, benzene, thinner, or alcohol. Use only authorized detergent if needed. Avoid spraying water directly onto the monitor.

Why is there no sound from the built-in speakers?

Ensure the audio cable is properly connected and the volume is turned up. Check that the sound is not muted (MUTE button). In PIP/POP/PBP mode, ensure Sound is set to On in the PIP menu. Also, the EZ Audio setting may affect output.

How do I reset the monitor to factory default settings?

In the OSD menu, go to SPECIAL > Reset. This initializes most settings, but language selection remains. Confirm the reset by pressing ENTER.

What does the RS-232C serial port allow?

The RS-232C port enables remote control of the monitor from a PC. You can turn power on/off, select input, adjust picture and sound settings, and set up Tile Mode. Use a standard RS-232C cable and control software with the provided command protocol.

USER MANUAL 55LP1M LG

P/NO.: 38289L0020A (0510-REV00) Printed in Korea

55LP1M

User's Guide

Please read this user's guide carefully before

operating your set.

Retain it for future reference.

Record model number and serial number of the set.

See the label attached on the product and give the

information to your dealer when you ask for service.

Table of Contents

Installation and Connection

Safety Precautions	A1
Accessories	A4
Using the Remote Control	A5
Name and Function of the Parts	A8
Connecting to External Devices	A9
When Connecting to your PC	A9
Watching RGB Outputs	A11
When Watching VCR/DVD	A12
When Watching HDTV (STB)/ DVD	A13
When Watching DVD(HDCP) from the VCR/DVD/Set top Box	A14
Watching AV Outputs	A15
How to mount the product assembly to the wall to protect the set tumbling	A16
To arrange cables in order - Optional	A17

Input Selection and Tracking

Selecting and Adjusting the Screen
How to adjust the OSD (On Screen Display) Screen	A21
Adjusting Screen Color	A22
Adjusting the audio function	A23
Selecting the Options	A24
Adjusting Screen CLOCK/PHASE and Position	A28
Adjusting PIP/POP/PBP Mode (Multiple Screen) Functions	A29

Miscellaneous

Troubleshooting	A31
Specifications	A34

is a trademark of SRS Labs, Inc. technology is incorporated under license from SRS Labs, Inc.

Safety Precautions

Please read these safety precautions carefully before using the product.

Warning

If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death.

Caution

If you ignore the caution message, you may be slightly injured or the product may be damaged.

Precautions in Installing the Product

Warning

• Keep away from heat sources like electrical heaters.
• Electrical shock, fire, malfunction or deformation may occur.
• Keep the packing anti-moisture material or vinyl packing out of the reach of children.
• Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children. Do not put heavy objects on the product or sit upon it.
• If the product collapses or is dropped, you may be injured. Children must pay particular attention. Do not leave the power or signal cable unattended on a pathway.
• The passerby can trip, which can cause electrical shock, fire, product breakdown or injury. Install the product in a neat and dry place.
• Dust or moisture can cause electrical shock, fire or product damage. If you can smell smoke or other odors or hear a strange sound, unplug the power cord and contact the service center.
• If you continue to use without taking proper measures, electrical shock or fire can occur. ■ If you dropped the product or the case is broken, turn off the product and unplug the power cord.
• If you continue to use without taking proper measures, electrical shock or fire can occur. Contact the service center. ■ Do not drop metallic objects such as coins, hair pins, chopsticks or wire into the product, or inflammable objects such as paper and matches. Children must pay particular attention.
• Electrical shock, fire or injury can occur. If a foreign object is dropped into the product, unplug the power cord and contact the service center.

Caution

■ Make sure the product ventilation holes are not blocked. Install the product in a suitably wide place (more than 10cm from the wall) - If you install the product too close to the wall, it may be deformed or fire can break out due to internal heat. ■ Do not block the ventilation hole of the product by a tablecloth or curtain. - The product can be deformed or fire can break out due to overheating inside the product. ■ Install the product on a flat and stable place that has no risk of dropping the product. - If the product is dropped, you may be injured or the product may be broken. ■ Install the product where no EMI occurs. - Keep the product away from direct sunlight. - The product can be damaged.

Electrical Power Related Precautions

Warning

■ Make sure the circuit is well grounded.

- You may be electrocuted or injured.

■ Use rated voltage only.

- The product can be damaged, or you may be electrocuted.

■ During a thunder or lightning storm, unplug the power cable or signal cable.

- You may be electrocuted or a fire can break out.

■ Do not connect several extension cords, electrical appliances or electrical heaters to a single outlet. Use a power bar with a grounding terminal designed for exclusive use with the computer.

- A fire can break out due to overheating.

Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, dry the power plug completely or wipe dust off.

You may be electrocuted due to excess moisture.

If you don't intend to use the product for a long time, unplug the power cable from the product.

Covering dust can cause a fire, or insulation deterioration can cause electric leakage, electric shock or fire.

Connect the power cable completely.

If the power cable is not connected completely, a fire can break out.

Hold the plug when pulling out the power cable. Do not bend the power cord with excessive force or put heavy objects on the power cord.

The power line can be damaged, which may cause electric shock or fire.

Do not insert a conductor (like a metal chopstick) into one end of the power cable while the other end is connected to the input terminal on the wall. Additionally, do not touch the power cable right after plugging into the wall input terminal.

You may be electrocuted.

The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation.

Caution

Do not unplug the power cord while the product is in use.

Electrical shock can damage the product.

Precautions in Moving the Product

Warning

■ Make sure to turn off the product.

- You may be electrocuted or the product can be damaged.

■ Make sure to remove all cables before moving the product.

- You may be electrocuted or the product can be damaged.

Safety Precautions

Caution

■ Do not shock the product when moving it. - You may be electrocuted or the product can be damaged. ■ Do not dispose of the product packing or box. Use it when you move. ■ Make the panel face forward and hold it with both hands to move. - If you drop the product, the damaged product can cause electric shock or fire. Contact the service center for repair.

- Precautions in Using the Product

Warning

■ Do not disassemble, repair, or modify the product at your own discretion. - Fire or electric shock accident can occur. - Contact the service center for check, calibration, or repair. ■ Do not spray water on the product or scrub with an inflammable substance (thinner or benzene). Fire or electric shock accident can occur. - Keep the product away from water. - Fire or electric shock accident can occur.

Caution

■ Do not put or store inflammable substances near the product. - There is a danger of explosion or fire due to careless handling of the inflammable substances. ■ When cleaning the brown tube surface, unplug the power cord and scrub with soft cloth to prevent scratching. Do not clean with a wet cloth. - The water can sink into the product, which can cause electric shock or serious malfunction.

■ Take a rest from time to time to protect your vision.

- Keep the product clean at all times.

Take a comfortable and natural position when working with a product to relax the muscles.

Take a regular break when working with a product for a long time.

Do not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make a scratch on it.

Keep proper distance from the product.

Your vision may be impaired if you look at the product too closely.

Set the appropriate resolution and clock by referring to the User's Guide.

Your vision can be impaired.

Use authorized detergent only when cleaning the product. (Do not use benzene, thinner or alcohol.)

Product can be deformed.

On Disposal

The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority.

Accessories

Please check the accessories in the product package.

* The product and the accessories can be different from the figures shown here.

OR

Product

User's Guide

15-pin D-Sub Signal Cable

DVI-D Signal Cable

2-TV Bracket Bolts

2-TV Brackets, 2-Wall Bracket

Power Cord

Audio Cable (PC) (Applicable only for models that support the speakers)

RCA-PC Audio Cable (Applicable only for models that support the speakers)

Twister Holder Remote Control/Batteries

Optional

Wall-mount Rack

Please refer to the enclosed "Installation Guide" when installing the wall-mount rack.

- Inserting batteries into remote Control.

1. Take out the battery cap.
2. Insert batteries with correct polarity (+/-).
3. Close the battery cap.
4. You can use a remote control at a distance of 7 meters and within a 30-degree angle (left/right) of the receiving unit.
5. Dispose of used batteries in the recycle bin to prevent environmental pollution.

Using the Remote Control

Names of the Remote Control Buttons

Using the Remote Control

EXIT

Exit the OSD by pressing the EXIT button.

PIP (Picture in Picture) Button

The sub-screen moves to the next mode whenever you press this button.

: SMALL -> MEDIUM -> LARGE -> OFF

POP (Picture out Picture) Button

The sub-screen moves to the next mode whenever you press this button.

:POP ON -> PBP(FULL) -> PBP(4:3) -> OFF

PIP

POP ON

PBP (FULL)

PBP (4:3)

SWAP Button

You can swap the main screen and the sub-screen when the PIP/POP/PBP function is used.

PIP

POP

PBP

When 'Input Signal 1' comes on in the main screen, only 'Input Signal 2' can be displayed on the sub-screen. On the contrary, if the main screen displays 'Input Signal 2', the sub-screen can display 'Input Signal 1' only. You can swap 'Input Signal 1' and 'Input Signal 2' using the SWAP button.

*PIP function is not supported in 480i, 576i and 1080i modes.

Sub-Screen\Main Screen	AV	S-Video	COMPONENT	RGB1	RGB2	DVI
AV	X	X	X	●	●	●
S-Video	X	X	X	●	●	●
COMPONENT	X	X	X	●	●	●
RGB1	●	●	●	X	X	●
RGB2	●	●	●	X	X	●
DVI	●	●	●	●	●	X

Name and Function of the Parts

* The product image in the user's guide could be different from the actual image.  Rear View  ① RS-232C Serial Ports ② Power Connector : Connect the power cord ③ Wired Remote Control Port 4 PC Signal Inputs ⑤ PC Sound Jack : Connect the audio cable to the *LINE OUT jack of the PC sound card. 6 AV Ports

*LINE OUT

A terminal used to connect to the speaker including a built-in amplifier (Amp). Make sure that the connecting terminal of the PC sound card is checked before connecting. If the Audio Out of PC sound card has only Speaker Out, reduce the PC volume. If the Audio Out of the PC sound card supports both Speaker Out and Line Out, convert to Line Out using the card jumper of the program (Refer to the Sound Card Manual).

Connecting to External Devices

■ When Connecting to your PC

1 First of all, see if the computer, product and the peripherals are turned off. Then, connect the signal input cable. (A) When connecting with the DVI signal input cable. (B1) When connecting with the D-Sub signal input cable. (IBM compatible PC1) B2 When connecting with the D-Sub signal input cable. (IBM compatible PC2) C When connecting with the D-Sub signal input cable. (Macintosh)  ② Connect the power cord.  ③ A Turn on power by pressing the power button on the product.  (B) Turn on the PC. 4 Select an input signal. Press the INPUT button on the remote control to select the input signal. INPUT → ▼▲→ ENTER Or, press the INPUT button at the front side of the product. INPUT → ▼▲→ SELECT (A) When connecting with a DVI-D signal input cable. \- Select DVI : DVI-D digital signal. When connecting with a D-Sub signal input cable. B1C • Select RGB1 : 15-pin D-Sub analog signal. B2 • Select RGB2 : 15-pin D-Sub analog signal.   • How to connect to two computers. Connect the signal cables (DVI and D-Sub) to each computer. Press the INPUT button in a remote control to select the computer to use. - Directly connect to a grounded power outlet on the wall or a power bar with a ground wire.

Connecting to External Devices

■ Watching RGB Outputs Use this function when displaying ANALOG RGB inputs of a PC to the other product.

• To use different products connected to each other

Connect one end of the signal input cable(15-pin D-Sub Signal Cable) to the RGB OUT connector of product 1 and connect the other end to the RGB INPUT connector of other products. \- Change source to RGB1 when desiring to see input signal of the RGB1, and select RGB2 when desiring to input signal of the RGB2. 

■ When watching VCR / DVD

1 Connect the video cable as shown in the below figure and then connect the power cord (See page A9). (A) When connecting with a RCA cable. \- Connect the input terminal with a proper color match. (Video – Yellow, Sound (left) – White, Sound (right) – Red) (B) When connecting with a S-Video cable. \- Connect to the S-Video input terminal to watch high image quality movies.  ② Select an input signal. Press the INPUT button on the remote control to select the input signal. INPUT → ▼▲→ ENTER Or, press the INPUT button at the front side of the product. INPUT → ▼▲→ SELECT (A) When connecting with an RCA cable. - Select AV. B When connecting with an S-Video cable. • Select S-Video. 

Connecting to External Devices

When watching HDTV(STB)/DVD

1 Connect the video/audio cable as shown in the below figure and then, connect the power cord (See page A9). \- Connect the input terminal with a proper color match. 

Mode\Terminal	Component
480i	○
576i	○
480p	○
576p	○
720p	○
1080i	○

② Select an input signal. Press the INPUT button on the remote control to select the input signal. INPUT → ▼▲→ ENTER Or, press the INPUT button at the front side of the product. INPUT → ▼▲→ SELECT \- Select COMPONENT. 

When watching DVI-D(HDCP) from the VCR/DVD/Set-top Box

1 Connect the video/audio cable as shown in the below figure and then connect the power cord (See page A9).  ② Select an input signal. Press the INPUT button on the remote control to select the input signal. INPUT → ▼▲→ ENTER Or, press the INPUT button at the front side of the product. INPUT → ▼▲→ SELECT \- Select DVI. 

Connecting to External Devices

■ Watching AV Outputs Connect to the external device if you record the broadcasting. \- When you set the input signal of the main screen as 'AV (CVBS)', you can transmit the signal that you're watching to the AV output terminal. 

How to mount the product assembly to the wall to protect the set tumbling

Please set it up carefully so the product doesn't fall over.

Set it up close to the wall so the product doesn't fall over when it is pushed backwards. The instructions shown below is a safer way to set up the product, which is to fix it on the wall so the product does-n't fall over when it is pulled in the forward direction. It will prevent the product from falling forward and hurting peo-ple. It will also prevent the product from damage caused by fall. Please make sure that children don't climb on or hang from the product.  1 The Product Back Side  2   3  1. Use the bracket and the bolt to fix the product to the wall as shown in the picture. 2. Secure the bracket with the bolt (not provided as parts of the product, must purchase separately) on the wall. 3. Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.

Notes

- When moving the product to another place undo the ropes first. - Use a product holder or a cabinet that is big and strong enough for the size and weight of the product. - To use the product safely make sure that the height of the bracket that is mounted on the wall is same as that of the product.

To arrange cables in order - Optional

1. Pull out the back panel cover using both hands by holding the sides of the cover.  2. Connect the cables.  3. Use the holes in the back panel to close the back cover. Pull the cables through the hole on the set and bundle the cables using the supplied twister holder.  

Selecting and Adjusting the Screen

 Name of the Buttons on front of the Unit  ENGLISH 

Power Button

\- Press this button to turn on the power. Press this button again to turn it off. 

Power Indicator

\- This indicator lights up green when the display operates normally(on mode). If the display is in sleep (Energy Saving) mode, this indicator color changes to amber. 

MENU Button

\- Use this button to show/hide the OSD (On Screen Display) menu screen. 

OSD Select / Adjust Button

\- Use this button to select an icon or adjust the setting in the OSD screen.  \- Use these buttons to directly control brightness and contrast of the PC signal (RGB1, RGB2 / DVI).   \- Adjust the volume. 

Selecting and Adjusting the Screen

Name of the Buttons on front of the Unit

 AUTO/SELECT Button [For PC Analog signal] 1) Auto in progress (Only 1920X1080 Mode) 2) Auto in Progress For optimal display change resolution to 1920X1080 [Other signals] • The current signal and mode information will be displayed.  INPUT Button INPUT → ▼▲ → AUTO/SELECT \- Select the input signal AV Composite Video S-Video Separate Video Component HDTV/ DVD RGB1 15-pin D-Sub analog signal RGB2 15-pin D-Sub analog signal DVI DVI digital signal    \- The unit that receives the signal from the remote control. 

OSD Menu

Icon	Function Description
	Adjusts screen brightness, contrast and color that you prefer.
PICTURE
	Adjusts the audio function.
SOUND
	Adjusts the screen status according to the circumstances.
SPECIAL
	Adjusts the screen video.
SCREEN
	Adjusts PIP/POP/PBP mode function.
PIP/POP/PBP

 OSD(On Screen Display) The OSD function enables you to adjust the screen status conveniently since it provides graphical presentation.

Selecting and Adjusting the Screen


How to adjust the OSD (On Screen Display) screen

 - Use the remote control to adjust the OSD screen. 1 Press the MENU Button, then the main menu of the OSD appears. 2 To access a control, use the ▼▲ Buttons. 3 When the icon you want becomes highlighted, press the ENTER Button. 4 To access a control, use the ▼▲ Buttons. 5 When the icon you want becomes highlighted, press the ENTER Button. 6 Use the ▼▲◀▶ Buttons to adjust the item to the desired level. 7 Accept the changes by pressing the ENTER Button. 8 Exit the OSD by pressing the EXIT Button. 

How to adjust the screen automatically

You need to adjust the screen display when connecting the product to a new computer or changing the mode. Refer to the following section to set an optimal product screen. Press the AUTO/SELECT button (AUTO button in a remote Control) in the PC analog signal. Then, an optimal screen status will be selected that fits into the current mode. If adjustment is not satisfactory, you need to adjust screen position, clock and phase in the OSD menu. Auto in progress 

Adjusting Screen Color

EZ Video  AV/S-Video/Component input only The EZ Video function automatically adjusts the screen image quality depending on the AV usage environment. • Dynamic : Select this option to display with a sharp image. - Standard: The most general and natural screen display status. - Mild : Select this option to display with a mild image. - Game : Select this option to enjoy dynamic image when playing a game. - User: Select this option to use the user-defined settings. 

Contrast

To adjust the contrast of the screen.

Brightness

To adjust the brightness of the screen.

Color

To adjust the color to desired level.

Sharpness

To adjust the cleanliness of the screen.

Tint

To adjust the tint to desired level. ACC  Selecting a factory setting color set. • Warm : Slightly reddish white. • Normal : Slightly bluish white. • Cool : Slightly purplish white.  If the input is RGB1, 2(D-Sub analog)/DVI(DVI Digital), the adjustable items in the ACC function are color temp (6500K / 9300K / 3600K). If the 'EZ Video' setting in the PICTURE menu is set to Dynamic, Standard, Mild or Game the subsequent menus will be automatically set.

Selecting and Adjusting the Screen


Adjusting Screen Color

ACC 

RGB1, 2 / DVI input only

• 6500K/9300K/3600K Selecting a factory setting color set. 6500K: Slightly reddish white. 9300K: Slightly bluish white. 3600K: Slightly yellowish white. \- User : Select this option to use the user-defined settings.  Contrast To adjust the contrast of the screen. Brightness To adjust the brightness of the screen. Red / Green / Blue Set your own color levels. 

Adjusting the audio function

\- The function is only available on the products that come with speakers. EZ Audio  The best sound tone quality will be selected automatically depending on the video type that you're currently watching. \- Flat The most commanding and natural audio. • Music Select this option to enjoy the original sound when listening to the music. \- Movie Select this option to enjoy sublime sound. \- Speech Select this option to watch sports broadcasting. \- User Select this option to use the user-defined audio settings. Balance Use this function to balance sound from the left and right speakers. AVL To adjust uneven sound volumes across all channels or signals automatically to the most appropriate level. To use this feature, select On. SRS WOW Set the SRS WOW menu on. The SRS WOW function plays back the mono or stereo sound input with the dynamic surround effects. It will provide rich and profound sound tone. If you set the SRS WOW on, user audio setting can not be adjusted.  When connected to your computer and the 'EZ Audio' setting in the audio menu is one of Flat, Music, Movie or Speech, the available menus are Balance, AVL and SRS WOW. 

Selecting the options


Input

 If you press the button once, the following Input Signal Window will appear. Select the signal type you want using the ▼▲ button.

Child Lock

Use the ▼▲ buttons to select On or Off. The Set can be set up so that it can only be used with the remote control. This feature can prevent unauthorized viewing. In order to lock the OSD screen adjustment, set the Child Lock tab to the 'On' position. In order to unlock it, do the following : 1) Push the MENU button on the remote control and set Child Lock to the 'Off' position.

Language

To choose the language in which the control names are displayed.

Power

Use this function to set the power indicator on the front side of the product to On or Off. If you set Off, it will go off. If you set On at any time, the power indicator will automatically be turned on.

Indicator

To adjust the transparency of the OSD menu screen.

Selecting and Adjusting the Screen


Selecting the options

• To use this function

\- You can connect the product with several other products and use the Tile mode function.

Tile mode

 It is used to enlarge the screen and also used with several products to view screen,  Tile mode and choose Tile alignment and set the ID of the current product to set location. * Only after pressing the ENTER button the adjustments made to the settings will be saved. 

- Position

The location of the screen can be adjusted at the Position menu and can be set by adjusting the size of the bezel. * If you exit the menu after making the changes to the settings the adjustments will be saved. 

• H Size

Adjust the horizontal size of the screen taking into account the size of the bezel.

• V Size

Adjust the vertical size of the screen taking into account the size of the bezel.

- Tile recall

Function to initialize and release Tile. All Tile setting are released when selecting. Tile recall and the screen returns to Full screen.

• ID

Select the location of the Tile by setting an ID. 

Selecting the options

- Tile mode

- Tile mode : row x column ( r = 1, 2, 3, 4 c = 1, 2, 3, 4 ) - 4 x 4 available. - Configuration of an integration screen is also available as well as configuration of one by one Display.  \- Tile mode (product 1 \~ 4) : r(2) x c(2)  \- Tile mode (product 1 \~ 9) : r(3) x c(3) 

Selecting and Adjusting the Screen


Selecting the options

\- Tile mode (product 1 \~ 2) : r(2) x c(1)  Reset Use this function to reset the product to the factory default. However, language selection will not be initialized. 

Selecting the options

 Set ID  You can assign a unique Set ID NO (name assignment) to each product when several products are connected for display. Specify the number (0\~99) using the ▼▲ button and exit. Use the assigned Set ID to individually control each product using the Product Control Program. Logo Display Lamp Use this function to set the Logo Dispaly Lamp on the front side of the product to On or Off. If you set it to On, the lamp will automatically be turned on. Light Sensor Use this function to set the Light Sensor on the front side of the product to On or Off. If you set it to On, the sensor will automatically be turned on. 

Adjusting Screen CLOCK/PHASE and Position

 

ARC

To select the image size of the screen.   *When the component input signal is 720p or 1080i, the spectacle function is not supported.

Auto config.

This button is for the automatic adjustment of the screen position, clock and phase. This function is suitable for analoge signal input only(RGB PC input only).

Clock

To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. This function is suitable for analoge signal input only(RGB PC input only).

Phase

To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. This function is suitable for analoge signal input only(RGB PC input only).

Position

 To adjust position of the screen (RGB PC input only). Press the ▶ button to display the submenu for position. Left Moving the screen position ▶ Right horizontally. ▲ Up Moving the screen position ▼ Down vertically.

Selecting and Adjusting the Screen


Adjusting PIP/POP/PBP Mode (Multiple Screen) Functions

 On/Off  PIP After selecting PIP in the PIP On/Off menu, the following menu items can be adjusted.  POP After selecting POP in the POP On/Off menu, the following menu items can be adjusted.  PBP After selecting PBP in the PBP On/Off menu, the following menu items can be adjusted. PIP input To select an input signal for PIP/POP/PBP. Size To adjust the size of the PIP/POP/PBP screen. (PIP : Small, Medium, Large / PBP : Full, 4:3) Image To adjust the image of the PIP/POP/PBP screen; Press the ▶ button to display the submenu for PIP/POP/PBP image. Use the ◀▶ buttons to adjust the item to the desired level. The items of the sub-menu may vary depending on the type of the source.  ■ Contrast Adjust PIP/POP/PBP screen contrast. ■ Brightness Adjust PIP/POP/PBP screen brightness. Color Adjust the PIP/POP/PBP screen color. ■Tint To adjust the tint to desired level. This function is available only in NTSC * The sub-menu can differ according to the type of the input signal. Sound To turn the PIP/POP/PBP sound on/off. 

Adjusting PIP/POP/PBP Mode (Multiple Screen) Functions

Position  To adjust the position to PIP screen. Swap  To switch the main-screen and sub-screen in PIP/POP/PBP mode. PIP    POP    PBP   

Troubleshooting

No image is displayed

● Is the product power cord connected? ● Is the power indicator light on? ● Power is on, power indicator is green but the screen appears extremely dark. ● Is the power indicator amber? \- Does the 'Out of range' message appear? \- Does the 'Check signal cable' message appear? • See if the power cord is properly connected to the outlet. • See if the power switch is turned on. - Adjust brightness and contrast again. \- If the product is in power saving mode, move the mouse or press any key. \- The signal from the PC (video card) is out of the vertical or horizontal frequency range of the product. Adjust the frequency range by referring to the Specifications in this manual.

* Maximum resolution

RGB1 / RGB2 : 1920 X 1080 @60Hz DVI:1920 X 1080 @60Hz \- The signal cable between PC and product is not connected. Check the signal cable. \- Press the 'INPUT' menu in the remote Control to check the input signal.

'Controls locked' message appears.

● The 'Controls locked' message appears when pressing the Menu button. \- The control locking function prevents unintentional OSD setting change due to careless usage. To unlock the controls, simultaneously press the Menu button and ▶ button for several seconds. (You cannot set this function using the remote control buttons. You can set this function in the product only.)  * Vertical frequency: To enable the user to watch the product display, screen image should be changed tens of times every second like a fluorescent lamp. The vertical frequency or refresh rate is the times of image display per second. The unit is Hz. * Horizontal frequency: The horizontal interval is the time to display one vertical line. When 1 is divided by the horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal frequency. The unit is kHz.

The screen image looks abnormal.

● Is the screen position wrong? ● Do thin lines appear on the background screen? ● Horizontal noise appears or the characters look blurred. \- Screen size is automatically adjusted when connected to the PC. ● Brightness differs in the main and sub screen when connected to the PC. ● The screen is displayed abnormally. \- D-Sub analog signal – Press the "AUTO" button in the remote control to automatically select the optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Position OSD menu. \- See if the video card resolution and frequency are supported by the product. If the frequency is out of range, set to the recommended resolution in the Control Panel – Display – Setting menu. \- D-Sub analog signal – Press the "AUTO" button in the remote control to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Clock OSD menu. \- D-Sub analog signal – Press the "AUTO" button in the remote control to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Phase OSD menu. \- If the screen size is not full when connected to the PC, execute the PIP/POP/PBP to change to full screen mode. \- You cannot adjust brightness and tint in the PIP/POP/PBP Screen menu for the sub-screen among PIP/POP/PBP menus. Therefore, brightness can be different for the sub-screen. \- The proper input signal is not connected to the signal port. Connect the signal cable that matches with the source input signal.

After-image appears on the product.

● After-image appears when the product is turned off. \- If you use a fixed image for a long time, the pixels may be damaged quickly. Use the screensaver function.

Troubleshooting

The audio function does not work.

● No sound? ● No sound is available when the PIP/POP/PBP mode is engaged. ● Sound is too dull. ● Sound is too low. • See if the audio cable is connected properly. - Adjust the volume. • See if the sound is set properly. • See if the Sound is set to On in the PIP/POP/PBP menu. - Select the appropriate equalize sound. - Adjust the volume.

The screen size function in the OSD menu does not work.

● The screen size function in the OSD menu does not work. • See if the PIP/POP/PBP function is in use. If the PIP/POP/PBP function is in use, the screen size function may not work.

Screen color is abnormal.

● Screen has poor color resolution (16 colors). - Screen color is unstable or monocolored. ● Do black spots appear on the screen? - Set the number of colors to more than 24 bits (true color) Select Control Panel – Display – Settings – Color Table menu in Windows. - Check the connection status of the signal cable. Or, re-insert the PC video card. - Several pixels (red, green, white or black color) may appear on the screen, which can be attributable to the unique characteristics of the LCD panel. It is not a malfunction of the LCD.

Specifications

The product specifications can change without prior notice for product improvement.

LCD Panel	55 inches (139.7 cm) TFT (Thin Film Transistor)LCD (Liquid Crystal Display) PanelVisible diagonal size: 139.7 cm0.630 mm (Pixel Pitch)
Power	Rated VoltageAC 100-240V~ 50/60Hz 3.5APower ConsumptionOn Mode : 350WSleep Mode : ≤ 3WOff Mode : ≤ 3W
Stand range	-30°~30°
Dimensions &Weight	[1][2]Width x Height x Depth[1] 1375.4 cm (541.5 inches) x 943.2 cm (371.34 inches) x 320.0 cm (125.98 inches)[2] 1612.0 cm (634.6 inches) x 943.2 cm (371.34 inches) x 320.0 cm (125.98 inches)
	Net[1] 68.5 kg (151.01 lbs)[2] 72.9 kg (160.71 lbs)

NOTE

■ Information in this document is subject to change without notice.

Specifications

The product specifications can change without prior notice for product improvement.

Video Signal	Max. Resolution	RGB1 / RGB2 : 1920 X 1080 @60HzDVI : 1920 X 1080 @60Hz – It may not be supporteddepending on the OS or video card type.
	Recommended Resolution	RGB1 / RGB2 : WSXGA 1920 X 1080 @60HzDVI : WSXGA 1920 X 1080 @60Hz – It may not besupported depending on the OS or video card type.
	Horizontal Frequency	30 - 83 kHz
	Vertical Frequency	56 - 85 Hz
	Synchronization Type	Separate/Composite/SOG (Sync On Green)/Digital
Input Connector		15-pin D-Sub type, DVI-D (digital), S-Video,Composite Video, HDTV, DVD, RS-232C
Environmental Conditions	Operational ConditionStorage Condition	Temperature: 5°C ~ 35°C , Humidity: 10% ~ 80%Temperature: -20°C ~ 60°C , Humidity: 5% ~ 95%

* Applicable only for models that support the speakers

	RMS Audio Output	10W+10W(R+L)
Audio	Input Sensitivity	0.7Vrms
	Speaker Impedance	8Ω

NOTE

■ Information in this document is subject to change without notice.  PC Mode – Preset Mode

Preset mode		Horizontal Frequency (kHz)	Vertical Frequency (Hz)	Preset mode		Horizontal Frequency (kHz)	Vertical Frequency (Hz)
1	VGA 640 x 350	31.469	70	11	VESA 1024 x 768	60.123	75
2	VGA 720 x 400	31.468	70	12	VESA 1024 x 768	68.68	85
3	VGA 640 x 480	31.469	60	13	VESA 1360 x 768	47.72	60
4	VESA 640 x 480	37.500	75	14	VESA1280 x 1024	63.981	60
5	VESA 640 x 480	43.269	85	15	VESA1280 x 1024	79.98	75
6	VESA 800 x 600	37.879	60	16	VESA1920 x 1080	66.587	60
7	VESA 800 x 600	46.875	75
8	VESA 800 x 600	53.674	85
9	MAC 832 x 624	49.725	75
10	VESA 1024 x 768	48.363	60

 Power Indicator

Mode	Product
On Mode	Green
Sleep Mode	Amber
Off Mode	-

Specifications

VESA wall mounting

Connected to another object (stand type and wall-mounted type.) This product accepts a VESA-compliant mounting interface pad.- (optional) For further information, refer to the VESA Wall Mounting Instruction Guide. 

RS-232C GUIDE

 To remote control the Product Use this method to connect several products to a single PC. You can control several products at a time by connecting them to a single PC. 

Connecting the cable

Connect the RS-232C cable as shown in the picture. * The RS-232C protocol is used for communication between the PC and product. You can turn the product on/off, select an input source or adjust the OSD menu from your PC.  

Communication Parameter

G Baud Rate : 9600bps (UART) G Data Length : 8bits G Parity Bit: None G Stop Bit : 1bit G Flow Control: None G Communication Code : ASCII code  Command Reference List

	COMMAND1	COMMAND2	DATA(Hexa)
01. Power	k	a	00H - 01H
02. Input Select	k	b	02H - 08H
03. Aspect Ratio	k	c	01H - 06H
04. Screen Mute	k	d	00H - 01H
05. Volume Mute	k	e	00H - 01H
06. Volume Control	k	f	00H - 64H
07. Contrast	k	g	00H - 64H
08. Brightness	k	h	00H - 64H
09. Color	k	i	00H - 64H
10. Tint	k	j	00H - 64H
11. Sharpness	k	k	00H - 64H
12. OSD Select	k	l	00H - 01H
13. Remote Lock On/Off	k	m	00H - 01H
14. PIP/PBP/POP On/Off	k	n	00H - 03H
15. PIP Position	k	q	00H - 03H
16. Balance	k	t	00H - 64H
17. ACC	k	u	00H - 04H
18. PIP/PBP/POP SOURCE	k	y	00H - 08H
19. Auto Configure	j	u	01H
20. Key	m	c	Key Code
21. Tiling Mode	d	d	00H - 0FH
22. Tile H Position	d	e	00H - 64H
23. Tile V Position	d	f	00H - 64H
24. Tile H Size	d	g	00H - 64H
25. Tile V Size	d	h	00H - 64H
26. Tile ID Set	d	i	00H - 63H
27. Elapsed time return	d	l	FFH
* 28. Light Sensor value return	d	m	FFH
* 29. Temperature value return	d	n	FFH
* 30. Fan On/Off	d	o	00H - 01H
* 31. Lamp fault check	d	p	FFH
* 32. Video input fault return	d	q	FFH

*: Optional 

Transmission / Receiving Protocol

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

* [Command 1]: First command. (j, k, m, d) * [Command 2]: Second command. * [Set ID]: You can adjust the set ID to choose desired product ID number in Special menu. Adjustment range is 0 \~ 99. When selecting Set ID '0', every connected TV set is controlled. Set ID is indicated as decimal (0\~99) on menu and as Hexa decimal (0x0\~0x64) on transmission/receiving protocol. * [DATA]: To transmit command data. Transmit 'FF' data to read status of command. * [Cr]: Carriage Return ASCII code '0x0D' * [ ]: ASCII code Space (0x20)

OK Acknowledgement

[Command2][ ][Set ID][ ][OK][Data][x]

* The Product transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.

Error Acknowledgement

[Command2][ ][Set ID][ ][NG][Data][x]

* The Product transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors. Data 1: Illegal Code 2: Not supported function 3: Wait more time 

Transmission / Receiving Protocol

01. Power On (Command: a)

G To control Power On/Off of the Set. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0: Power Off 1: Power On Acknowledgement [a][ ][Set ID][ ][OK][Data][x] G To show the status of Power On/Off. Transmission [k][a][ ][Set ID][ ][FF][Cr] Data 0: Power Off 1: Power On Acknowledgement [a][ ][Set ID][ ][OK][Data][x] * The Product transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.

02. Input Select (Command: b) (Main Picture Input)

G To select input source for the Set. You can also select an input source using the INPUT button on the remote control. Transmission [k][b][ ][Set ID][ ][Data][Cr] Data 2:AV 6:RGB1 3 : S-Video 7 : RGB2 4 : Component 8 : DVI Acknowledgement [b][ ][Set ID][ ][OK][Data][x]

03. Aspect Ratio (Command: c)

To adjust the screen format. You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Screen menu. Transmission [k][c][ ][Set ID][ ][Data][Cr] Data 1 : 4:3 (Video) 2: Full (PC, Video) 3 : Spectacle (Video) 4:Zoom1(PC,Video) 5:Zoom2(Video) 6:1:1 (PC) Acknowledgement [c][ ][Set ID][ ][OK][Data][x]

04. Screen Mute (Command: d)

G select screen mute on/off. Transmission [k][d][ ][Set ID][ ][Data][Cr] Data 0 : Screen mute off (Picture on) 1: Screen mute on (Picture off) Acknowledgement [d][ ][Set ID][ ][OK][Data][x] 

Transmission / Receiving Protocol

05. Volume Mute (Command: e)

G To control On/Off of the Volume Mute.

Transmission

[k][e][ ][Set ID][ ][Data][Cr] Data 0 : Volume Mute On (Volume Off) 1: Volume Mute Off (Volume On)

Acknowledgement

[e][ ][Set ID][ ][OK][Data][x] Data 0 : Volume Mute On (Volume Off) 1: Volume Mute Off (Volume On)

06. Volume Control (Command: f)

g To adjust Volume.

Transmission

[k][f][ ][Set ID][ ][Data][Cr] Data Min: 00H \~ Max: 64H (Hexadecimal code)

Acknowledgement

[f][ ][Set ID][ ][OK][Data][x] Data Min : 00H - Max : 64H * Real data mapping 0:Step 0 A:Step 10 : F : Step 15 10:Step 16 : 64: Step 100

07. Contrast (Command: g)

G To adjust screen contrast. You can also adjust the contrast in the Picture menu.

Transmission

[k][g][ ][Set ID][ ][Data][Cr] Data Min:00H\~Max:64H \- Refer to 'Real data mapping' as shown below.

Acknowledgement

[g][ ][Set ID][ ][OK][Data][x] * Real data mapping 0:Step 0 A: Step 10 : F:Step 15 10:Step 16 64:Step 100

08. Brightness (Command: h)

G To adjust screen brightness. You can also adjust the brightness in the Picture menu.

Transmission

[k][h][ ][Set ID][ ][Data][Cr] Data Min:00H\~Max:64H • Refer to 'Real data mapping' as shown below.

Acknowledgement

[h][ ][Set ID][ ][OK][Data][x] * Real data mapping 0 : Step A : Step 10 ; F : Step 15 10:Step 16 64:Step 100 

Transmission / Receiving Protocol

09. Color (Command: i) (Video only)

To adjust the screen color. You can also adjust the color in the Picture menu.

Transmission

[k][i][ ][Set ID][ ][Data][Cr] Data Min: 00H \~ Max: 64H (Hexadecimal code)

Acknowledgement

[i][ ][Set ID][ ][OK][Data][x] Data Min: 00H \~ Max: 64H

10. Tint (Command: j) (AV/S-Video: NTSC only)

To adjust the screen tint. You can also adjust the tint in the Picture menu.

Transmission

[k][j][ ][Set ID][ ][Data][Cr] Data Red: 00H \~ Green: 64H (Hexadecimal code)

Acknowledgement

[j][ ][Set ID][ ][OK][Data][x] Data Red: 00H \~ Green: 64H * Tint : -50 \~ +50

11. Sharpness (Command: k) (Video only)

G To adjust the screen Sharpness. You can also adjust the sharpness in the Picture menu.

Transmission

[k][k][ ][Set ID][ ][Data][Cr] Data Min : 00H \~ Max : 64H (Hexadecimal code)

Acknowledgement

[k][ ][Set ID][ ][OK][Data][x] Data Min: 00H \~ Max: 64H 12. OSD Select(Command : l) G To control OSD on/off to the set.

Transmission

[k][I][ ][Set ID][ ][Data][Cr] Data 0: OSD Off 1: OSD On

Acknowledgement

[1][ ][Set ID][ ][OK][Data][x] Data 0: OSD Off 1: OSD On

13. Remote Control Lock/Key Lock (Command: m)

G To lock the remote control and the front panel controls on the set.

Transmission

[k][m][ ][Set ID][ ][Data][Cr] Data 0 : Lock Off 1 : Lock On

Acknowledgement

[m][ ][Set ID][ ][OK][Data][x] Data 0: Lock Off 1: Lock On G If you're not using the remote control and front panel controls on the set, use this mode. When main power is on/off, remote control lock is released. 

Transmission / Receiving Protocol

14. PIP/PBP/POP On/Off (Command: n)

G To control PIP/PBP/POP On/Off of the Set. Transmission [k][n][ ][Set ID][ ][Data][Cr] Data 0: OFF 1:PIP 2: PBP 3:POP Acknowledgement [n][ ][Set ID][ ][OK][Data][x] Data 0: OFF 1:PIP 2: PBP 3:POP

15. PIP Position (Command: q)

G To adjust PIP position. Transmission [k][q][ ][Set ID][ ][Data][Cr] Data 0 : Bottom of the right side on screen 1:Bottom of the left side on screen 2: Top of the left side on screen 3: Top of the right side on screen Acknowledgement [q][ ][Set ID][ ][OK][Data][x] Data 0 : Bottom of the right side on screen 1: Bottom of the left side on screen 2: Top of the left side on screen 3: Top of the right side on screen

16. Balance (Command: t)

G To adjust the sound balance. Transmission [k][t][ ][Set ID][ ][Data][Cr] Data Min:00H\~Max:64H (Hexadecimal code) Acknowledgement [t][ ][Set ID][ ][OK][Data][x] Data Min: 00H \~ Max: 64H * Balance : -50 \~ +50

17. ACC (Command: u)

G To adjust the screen color temperature. Transmission [k][u][ ][Set ID][ ][Data][Cr] Data 0 : Normal (9300K) 4 : 3600K 1: Cool PC:0,2,3,4 2:Warm(6500K) Video:0,1,2 3:User Acknowledgement [u][ ][Set ID][ ][OK][Data][x] Data 0 : Normal (9300K) 4 : 3600K 1: Cool PC:0,2,3,4 2:Warm(6500K) Video:0,1,2 3:User 

Transmission / Receiving Protocol

18. PIP/PBP/POP SOURCE (Command: y)

G To select the sub-screen source. Transmission [k][y][ ][Set ID][ ][Data][Cr] Data 2: AV 6:RGB1 3 : S-Video 7:RGB2 4: Component 8 : DVI

Acknowledgement

[y][ ][Set ID][ ][OK][Data][x] Data 2:AV 6:RGB1 3 : S-Video 7:RGB2 4: Component 8 : DVI

21. Tiling Mode (Command: d d)

G Change a Tiling Mode. Transmission [d][d][ ][Set ID][ ][Data][x]

Data	Description
00	Tiling mode is off.
12	1 x 2 mode(column x row)
13	1 x 3 mode
14	1 x 4 mode
...	...
44	4 x 4 mode

* The data can not be set to 0X or X0 except 00.

19. Auto Configure (Command: j u)

G To adjust picture position and minimize image shaking automatically. it works only in RGB(PC) mode.

Transmission

[j][u][ ][Set ID][ ][Data][Cr] Data 1 : To set

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

20. Key (Command: m c)

G To send IR remote key code.

Transmission

[m][c][ ][Set ID][ ][Data][Cr] Data Key code

Acknowledgement

[c][ ][Set ID][ ][OK][Data][x]

Acknowledgement

[d][ ][00][ ][OK/NG][Data][x]

22. Tile H Position (Command: d e)

G To set the horizontal position.

Transmission

[d][e][ ][Set ID][ ][Data][x] * The data range is from 00 to 64(in Hex).

Acknowledgement

[e][ ][Set ID][ ][OK/NG][Data][x] 

Transmission / Receiving Protocol

23. Tile V Position (Command: d f)

G To set the Vertical position. Transmission [d][f][ ][Set ID][ ][Data][x] * The data range is from 00 to 64(in Hex). Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]

24. Tile H Size (Command: d g)

G To set the Horizontal size. Transmission [d][g][ ][Set ID][ ][Data][x] * The data range is from 00 to 64(in Hex). Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]

25. Tile V Size (Command: d h)

G To set the Vertical size. Transmission [d][h][ ][Set ID][ ][Data][x] * The data range is from 00 to 64(in Hex). Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]

26. Tile ID Set (Command: d i)

G To assign the Tile ID for Tiling function. Transmission [d][i][ ][Set ID][ ][Data][x] * The data range is from 00 to 00 x 10 tile mode. Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]

27. Elapsed time return (Command: d l)

G To read the elapsed time. Transmission [d][I][ ][Set ID][ ][Data][x] * The data is always FF(in Hex). Acknowledgement [1][ ][Set ID][ ][OK/NG][Data][x]

*28. Light Sensor value Return (Command: d m) - Optional

G To read the light sensor value for adjusting the product brightness depending on the surrounding brightness. Transmission [d][m][ ][Set ID][ ][Data][x] * The data is always FF(in Hex). Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x] 

Transmission / Receiving Protocol

*29. Temperature value Return (Command: d n) - Optional

G To read the inside temperature value. Transmission [d][n][ ][Set ID][ ][Data][x] * The data is always FF(in Hex). Acknowledgement [n][ ][Set ID][ ][OK/NG][Data][x] Data are 1 byte long in Hex ASCII format.

* 31. Lamp fault Check (Command: d p) - Optional

G To check lamp fault. Transmission [d][p][ ][Set ID][ ][Data][x] * The data is always FF(in Hex). Acknowledgement [p][ ][Set ID][ ][OK/NG][Data][x] 0:NG 1:OK

*30. Fan On/Off (Command: d o) - Optional G To control Fan On/Off to set.

Transmission [d][o][ ][Set ID][ ][Data][x] Data 0 : Fan Off 1 : Fan On Acknowledgement [o][ ][Set ID][ ][OK/NG][Data][x]

*32. Video input fault return (Command: d q) - Optional

G To check Video input fault. Transmission [d][q][ ][Set ID][ ][Data][x] * The data is always FF(in Hex). Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x] 0:NG 1:OK

How to connect

g Connect your wired remote control to Remote Control port on the Product.

Remote Control IR Code

G Output waveform

single pulse, modulated with 37.917KHz signal at 455KHz  Carrier frequency FCAR = 1/Tc = fosc/12 Duty ratio = T1/Tc = 1/3

G Configuration of frame

\- 1st frame  \- Repeat frame 

G Lead code


G Repeat code


G Bit description

 \- Bit "1" 

G Frame interval: Tf

• The waveform is transmitted as long as a key is depressed. 

Code (Hexa)	Function	Note
02	VOL (D)	R/C Button
03	VOL (E)	R/C Button
40	D	R/C Button
41	E	R/C Button
06	G	R/C Button
07	F	R/C Button
08	POWER ON/OFF	R/C Button (POWER On/Off)
5B	EXIT	R/C Button
09	MUTE	R/C Button
4D	EZ VIDEO(PSM)	R/C Button
52	EZ AUDIO(SSM)	R/C Button
98	INPUT(Source)	R/C Button
5A	AV	R/C Button
D8	S-VIDEO	R/C Button
BF	COMPONENT	R/C Button
C6	DVI	R/C Button
0E	SLEEP	R/C Button
43	MENU	R/C Button
44	ENTER	R/C Button
60	PIP	R/C Button
61	POP	R/C Button
63	SWAP	R/C Button
79	ARC	R/C Button
76	ARC(4:3)	R/C Button
77	ARC(Full)	R/C Button
AF	ARC(ZOOM1)	R/C Button
54	AUTO	R/C Button

Verwenden Sie dieses Verfahren, um mehrere Produkte an einen einzelnen PC anzuschließen. Sie können mehrere Produkte gleichzeitig verwenden, wenn Sie sie an einen einzelnen PC anschließen. 

Cable connection

Schließen Sie das RS-232C-Kabel wie im Bild gezeigt an. * Das RS-232C-Protokoll wird für die Kommunikation zwischen PC und Produkt verwendet. Von Ihrem PC aus, können Sie das Produkt ein-/ausschalten, eine Eingangsquelle wählen oder das OSD-Menü anpassen.  

Communication parameters

▶ Baudrate: 9600 bps (UART) ▶ Datenlänge: 8 bit Prüfbit: Ohne ▶ Stoppbit: 1 bit ▶ Flusskontrolle: Ohne ▶ Übertragungscode: ASCII-Code  Befehlsreferenzliste

	BEFEHL1	BEFEHL2	DATEN (Hex)
01. Power(Einschalten)	k	a	00H - 01H
02. Input Select(Eingangsauswahl)	k	b	02H - 08H
03. Aspect Ratio(Seitenverhältnis)	k	c	01H - 06H
04. Screen Mute(Bildschirm-Ruhezustand)	k	d	00H - 01H
05. Volume Mute(Stummschaltung)	k	e	00H - 01H
06. Volume Control(Lautstärkeregelung)	k	f	00H - 64H
07. Contrast(Kontrast)	k	g	00H - 64H
08. Brightness(Helligkeit)	k	h	00H - 64H
09. Color(Farbstärke)	k	i	00H - 64H
10. Tint(Farbton)	k	j	00H - 64H
11. Sharpness(Schärfe)	k	k	00H - 64H
12. OSD Select(OSD-Auswahl)	k	l	00H - 01H
13. Remote Lock On/Off(Fembedienungssperre Ein/Aus)	k	m	00H - 01H
14. PIP/PBP/POP On/Off(PIP/PBP/POP Ein/Aus)	k	n	00H - 03H
15. PIP Position(PIP-Bildlage)	k	q	00H - 03H
16. Balance	k	t	00H - 64H
17. ACC	k	u	00H - 04H
18. PIP/PBP/POP SOURCE(PIP/PBP/POP-QUELLE)	k	y	00H - 08H
19. Auto Configure(Auto-configuration)	j	u	01H
20. Key(Taste)	m	c	Tastencode
21. Tiling Mode(Kachelmodus)	d	d	00H - 0FH
22. Tile H Position(Kachel H-Position)	d	e	00H - 64H
23. Tile V Position(Kachel V-Position)	d	f	00H - 64H
24. Tile H Size(Kachel H-Größe)	d	g	00H - 64H
25. Tile V Size(Kachel V-Größe)	d	h	00H - 64H
26. Tile ID Set(Festlegen der Kachelkennung)	d	i	00H - 63H
27. Elapsed time return(Ablesen der Betriebszeit)	d	l	FFH
* 28. Light Sensor value return(Wertangabe des Lichtsensors)	d	m	FFH
* 29. Temperatur value return(Temperaturangabe)	d	n	FFH
* 30. Fan On/Off(Gebläse Ein/Aus)	d	o	00H - 01H
* 31. Lamp fault check(Funktionsprüfung der Lampe)	d	p	FFH
* 32. Video input fault return(Videoeingangsfehler-Rückgabe)	d	q	FFH

*: Optional 

Transmission/Reception protocol

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

* [Command 1]: Erster Befehl (j, k, m, d) * [Command 2]: Zweiter Befehl * [Set ID]: Sie können die Set-ID einstellen, um die gewünschte Produkt-ID im Menü „Speziell“ zu wählen. Der Einstellungsbereich beträgt 0-99. Wenn Sie als Set-ID „0“ auswählen, wird jedes angeschlossene TV-Set gesteuert. Die Set-ID wird im Menü als Dezimalzahl (0-99) und im Übertragungs-/Empfangsprotokoll als Hexadezimalzahl (0x0-0x64) angegeben. * [DATEN]: Für die Übertragung von Befehlsdaten „FF“ übertragen, um Befehlsstatus zu lesen. * [Cr]: Carriage Return (Zeilenschaltung) ASCII-Code „0x0D“ * [ ]: ASCII-Code „Leerschritt (0x20)“

OK acknowledgment

[Command2][ ][Set ID][ ][OK][Data][x]

* Das Produkt überträgt ACK (Bestätigung) beim Empfang normaler Daten basierend auf diesem Format. Wenn sich zu diesem Zeitpunkt Daten im Datenlesemodus befinden, werden die aktuellen Statusdaten angezeigt. Wenn sich die Daten im Datenschreibmodus befinden, werden die Daten an den PC zurückgegeben.

Error acknowledgment

[Command2][ ][Set ID][ ][NG][Data][x]

* Das Produkt überträgt ACK (Bestätigung) beim Empfang nicht normaler Daten von nicht brauchbaren Funktionen oder bei Kommunikationsfehlern basierend auf diesem Format. Daten 1: Ungültiger Code 2: Nicht unterstützte Funktion 3: Weiter warten 

Transmission/Reception protocol

01. Power (Command: a) (Power On)

▶ Für die Steuerung des Ein-/Ausschaltens des Geräts

Transmission

[k][a][ ][Set ID][ ][Data][Cr] Daten 0: Aus 1: Einschalten

Acknowledgment

[a][ ][Set ID][ ][OK][Data][x] ▶ Für die Anzeige des Ein-/Ausschaltens

Transmission

[k][a][ ][Set ID][ ][FF][Cr] Daten 0: Aus 1: Einschalten

Acknowledgment

[a][ ][Set ID][ ][OK][Data][x] * Das Produkt überträgt ACK (Bestätigung) beim Empfang normaler Daten basierend auf diesem Format. Wenn sich zu diesem Zeitpunkt Daten im Datenlesemodus befinden, werden die aktuellen Statusdaten angezeigt. Wenn sich die Daten im Datenschreibmodus befinden, werden die Daten an den PC zurückgegeben.

02. Input Select (Command: b) (Main Picture Input)

▶ Für die Auswahl der Eingangsquelle für das Gerät Sie können eine Eingangsquelle auch über die Taste INPUT an der Fernbedienung auswählen.

Transmission

[k][b][ ][Set ID][ ][Data][Cr]

Daten 2 : AV	6 : RGB1
3 : S-Video	7 : RGB2
4 : Component	8 : DVI

Acknowledgment

[b][ ][Set ID][ ][OK][Data][x]

03. Aspect Ratio (Command: c) (Main picture format)

Für die Einstellung des Bildformats Sie können das Bildformat auch über die Taste ARC (Aspect Ratio Control) der TV-Fernbedienung oder im Menü „Screen“ anpassen.

Transmission

[k][c][ ][Set ID][ ][Data][Cr] Daten 1 : 4:3 (Video) 2: Voll (PC, Video) 3 : Breitbild (Video) 4:Zoom1(PC,Video) 5:Zoom2(Video) 6:1:1(PC)

Acknowledgment

[c][ ][Set ID][ ][OK][Data][x]

04. Screen Mute (Command: d)

▶ Für die Aktivierung/Deaktivierung des Bildschirm-Ruhezustands

Transmission

[k][d][ ][Set ID][ ][Data][Cr] Daten 0 : Bildschirm-Ruhezustand aus (Bild an) 1 : Bildschirm-Ruhezustand ein (Bild aus)

Acknowledgment

[d][ ][Set ID][ ][OK][Data][x] 

Transmission/Reception Protocol

05. Volume Mute (Command: e)

▶ Für die Steuerung des Ein-/Ausschaltens der Stummschaltung

Transmission

[k][e][ ][Set ID][ ][Data][Cr] Daten 0 : Stummschaltung ein (Lautstärke aus) 1 : Stummschaltung aus (Lautstärke ein)

Acknowledgment

[e][ ][Set ID][ ][OK][Data][x] Daten 0 : Stummschaltung ein (Lautstärke aus) 1 : Stummschaltung aus (Lautstärke ein)

06. Volume Control (Command: f)

▶ Regeln Sie die Lautstärke.

Transmission

[k][f][ ][Set ID][ ][Data][Cr] Data Min.: 00 H \~ Max: 64 H (Hexadezimalcode)

Acknowledgment

[f][ ][Set ID][ ][OK][Data][x] Data Min.: 00 H \~ Max: 64 H

* Echtdatenzuordnung

0 : Schritt 0

:

A : Schritt 10

:

F : Schritt 15

10 : Schritt 16

:

64 : Schritt 100

07. Contrast (Command: g)

Für die Einstellung des Bildschirmkontrasts Sie können den Kontrast auch über das Menü „Imagine“ einstellen.

Transmission

[k][g][ ][Set ID][ ][Data][Cr] Data Min.: 00 H \~ Max: 64 H \- Siehe „Echtdatenzuordnung“ nachfolgend.

Acknowledgment

[g][ ][Set ID][ ][OK][Data][x] * Echtdatenzuordnung 0 : Schritt 0 A: Schritt 10 F : Schritt 15 10 : Schritt 16 64: Schritt 100

08. Brightness (Command: h)

Für die Einstellung der Bildschirmhelligkeit Sie können die Helligkeit auch über das Menü „Imagine“ einstellen.

Transmission

[k][h][ ][Set ID][ ][Data][Cr] Data Min.: 00 H \~ Max: 64 H \- Siehe „Echtdatenzuordnung“ nachfolgend.

Acknowledgement

[h][ ][Set ID][ ][OK][Data][x] * Echtdatenzuordnung 0 : Schritt A: Schritt 10 F : Schritt 15 10 : Schritt 16 64: Schritt 100 

Transmission/Reception protocol

09. Color (Command: i) (Video only)

Für die Einstellung der Bildschirmfarbstärke Sie können die Farbe auch über das Menü „Imagine“ einstellen.

Transmission

[k][i][ ][Set ID][ ][Data][Cr] Data Min.: 00 H \~ Max: 64 H (Hexadezimalcode)

Acknowledgement

[i][ ][Set ID][ ][OK][Data][x] Data Min.: 00 H \~ Max: 64 H

10. Tint (Command: j) (AV/S-Video: NTSC only)

▶ Für die Einstellung des Bildschirmfarbtons Sie können den Farbton auch über das Menü „Imagine“ einstellen.

Transmission

[k][j][ ][Set ID][ ][Data][Cr] Daten Rot: 00 H \~ Grün: 64 H (Hexadezimalcode)

Acknowledgement

[j][ ][Set ID][ ][OK][Data][x] Daten Rot: 00 H \~ Grün: 64 H * Farbton : -50 \~ +50

11. Sharpness (Command: k) (Video only)

Für die Einstellung der Bildschärfe Sie können die Bildschärfe auch über das Menü „Imagine“ einstellen.

Transmission

[k][k][ ][Set ID][ ][Data][Cr] Data Min.: 00 H \~ Max: 64 H (Hexadezimalcode)

Acknowledgement

[k][ ][Set ID][ ][OK][Data][x] Data Min.: 00 H \~ Max: 64 H

12. OSD Select (Command: I)

▶ Für die Steuerung des Ein-/Ausschaltens des OSD des Geräts

Transmission

[k][l][ ][Set ID][ ][Data][Cr] Daten 0: OSD Aus 1: OSD Ein

Confirmation

[1][ ][Set ID][ ][OK][Data][x] Daten 0: OSD Aus 1: OSD Ein

13. Remote Lock On/Off (Command: m)

▶ Für die Sperre der Tasten der Fernbedienung und der Frontkonsole am Gerät

Transmission

[k][m][ ][Set ID][ ][Data][Cr] Daten 0: Fernbedienungssperre Aus 1: Fernbedienungssperre Ein

Confirmation

[m][ ][Set ID][ ][OK][Data][x] Daten 0: Fernbedienungssperre Aus 1: Fernbedienungssperre Ein ▶ Wenn Sie die Fernbedienung und die Frontkonsole des Geräts nicht nutzen, verwenden Sie diesen Modus. Wenn der Hauptstrom aus-/eingeschaltet wird, wird die Fernbedienungssperre aufgehoben. 

Transmission/Reception Protocol

14. PIP/PBP/POP On/Off (Command: n)

▶ Für die Steuerung des Ein-/Ausschaltens von PIP/PBP/POP für das Gerät

Transmission

[k][n][ ][Set ID][ ][Data][Cr] Daten 0 : AUS 1:PIP 2 : PBP 3:POP

Confirmation

[n][ ][Set ID][ ][OK][Data][x] Daten 0 : AUS 1:PIP 2 : PBP 3:POP

15. PIP Position (Command: q)

▶ Für die Einstellung der PIP-Bildlage

Transmission

[k][q][ ][Set ID][ ][Data][Cr] Daten 0: Untere rechte Seite des Bildschirms 1: Untere linke Seite des Bildschirms 2: Obere linke Seite des Bildschirms 3: Obere rechte Seite des Bildschirms

Confirmation

[q][ ][Set ID][ ][OK][Data][x] Daten 0: Untere rechte Seite des Bildschirms 1: Untere linke Seite des Bildschirms 2: Obere linke Seite des Bildschirms 3: Obere rechte Seite des Bildschirms

16. Balance (Command: t)

▶ Für die Einstellung der Balance Übertragung [k][t][ ][Set ID][ ][Data][Cr] Data Min.: 00 H \~ Max: 64 H (Hexadezimalcode)

Confirmation

[t][ ][Set ID][ ][OK][Data][x] Data Min.: 00 H \~ Max: 64 H * Balance : -50 \~ +50

17. ACC (Command: u)

▶ Für die Einstellung der Farbtemperatur des Bildschirms

Transmission

[k][u][ ][Set ID][ ][Data][Cr] Daten 0 : Normal (9300K) 4 : 3600K 1:Kalt PC:0,2,3,4 2:Warm(6500K) Video:0,1,2 3 : Benutzer

Confirmation

[u][ ][Set ID][ ][OK][Data][x] Daten 0 : Normal (9300K) 4 : 3600K 1:Kalt PC:0,2,3,4 2:Warm(6500K) Video:0,1,2 3 : Benutzer 

Transmission/Reception protocol

18. PIP/PBP/POP SOURCE (Command: y)

▶ Für die Auswahl der Unterbild-Quelle Übertragung [k][y][ ][Set ID][ ][Data][Cr]

Daten 2 : AV	6 : RGB1
3 : S-Video	7 : RGB2
4 : Component	8 : DVI

Confirmation

[y][ ][Set ID][ ][OK][Data][x]

Daten 2 : AV	6 : RGB1
3 : S-Video	7 : RGB2
4 : Component	8 : DVI

19. Auto Configure (Command: j u)

▶ Für die automatische Einstellung der Bildposition und die automatische Minimierung des Bildwackelns. Nur in RGB (PC)-Modus.

Transmission

[j][u][ ][Set ID][ ][Data][Cr] Daten 1: Einstellen Acknowledgement [u][ ][Set ID][ ][OK][Data][x]

20. Key (Command: m c)

▶ Für das Senden des IR-Fernbedienungs-Tastencodes

Transmission

[m][c][ ][Set ID][ ][Data][Cr] Daten-Tastencode

Confirmation

[c][ ][Set ID][ ][OK][Data][x]

21. Tiling Mode (Command: d d)

▶ Ändern eines Kachelmodus Übertragung [d][d][ ][Set ID][ ][Data][x]

Daten	Beschreibung
00	Der Kachelmodus ist aus.
12	1 x 2-Modus (Spalte x Reihe)
13	1 x 3-Modus
14	1 x 4-Modus
...	...
44	4 x 4-Modus

* Die Daten können außer auf 00 nicht auf 0X oder X0 gesetzt werden.

Confirmation

[d][ ][00][ ][OK/NG][Data][x]

22. Tile H Position (Command: d e)

▶ Zur Einstellung der horizontalen Position Übertragung [d][e][ ][Set ID][ ][Data][x] * Die Daten müssen zwischen 00 und 64 (Hex) liegen.

Confirmation

[e][ ][Set ID][ ][OK/NG][Data][x] 

Transmission/Reception protocol

23. Tile V Position (Command: d f)

▶ Zur Einstellung der vertikalen Position Übertragung [d][f][ ][Set ID][ ][Data][x] * Die Daten müssen zwischen 00 und 64 (Hex) liegen. Bestätigung [f][ ][Set ID][ ][OK/NG][Data][x]

24. Tile H Size (Command: d g)

▶ Zur Einstellung der horizontalen Größe Übertragung [d][g][ ][Set ID][ ][Data][x] * Die Daten müssen zwischen 00 und 64 (Hex) liegen. Bestätigung [g][ ][Set ID][ ][OK/NG][Data][x]

25. Tile V Size (Command: d h)

▶ Zur Einstellung der vertikalen Größe Übertragung [d][h][ ][Set ID][ ][Data][x] * Die Daten müssen zwischen 00 und 64 (Hex) liegen. Bestätigung [h][ ][Set ID][ ][OK/NG][Data][x]

26. Tile ID Set (Command: d i)

Zur Einstellung der Kachelkennung für den Kachelmodus Übertragung [d][i][ ][Set ID][ ][Data][x] * Die Daten können im Kachelmodus zwischen 00 und 00 x10 liegen. Bestätigung [i][ ][Set ID][ ][OK/NG][Data][x]

27. Elapsed time return (Command: d l)

▶ Zum Ablesen der Betriebszeit Übertragung [d][I][ ][Set ID][ ][Data][x] * Die Daten sind immer auf FF (Hex) gesetzt. Bestätigung [1][ ][Set ID][ ][OK/NG][Data][x]

*28. Light Sensor value Return (Command: d m) - Optional

Über diesen Befehl können Sie den Lichtsensorwert zur Anpassung der Bildschirmhelligkeit an die Helligkeit der Umgebung ablesen. Übertragung [d][m][ ][Set ID][ ][Data][x] * Die Daten sind immer auf FF (Hex) gesetzt. Bestätigung [m][ ][Set ID][ ][OK/NG][Data][x] 

Transmission/Reception Protocol

*29. Temperature value

Return(Command : d n) (Temperaturangabe (Befehl: d n)) - Optional ▶ Zum Ablesen der Innentemperatur Übertragung [d][n][ ][Set ID][ ][Data][x] * Die Daten sind immer auf FF (Hex) gesetzt. Bestätigung [n][ ][Set ID][ ][OK/NG][Data][x] Die Datenlänge beträgt 1 Byte im Hex-/ASCII-Code.

*30. Fan On/Off (Command: d o)

(Gebläse Ein/Aus (Befehl: d o)) - Optional ▶ Für die Steuerung des Ein-/Ausschaltens des Gerätegebläses. Übertragung [d][o][ ][Set ID][ ][Data][x] Daten 0: Gebläse Aus 1 : Gebläse Ein Bestätigung [o][ ][Set ID][ ][OK/NG][Data][x]

*31. Lamp fault Check (Command: d p) - Optional

▶ Zur Funktionsprüfung der Lampe Übertragung [d][p][ ][Set ID][ ][Data][x] * Die Daten sind immer auf FF (Hex) gesetzt. Bestätigung [p][ ][Set ID][ ][OK/NG][Data][x] 0:NG 1:OK

*32. Video input fault return (Command: d q) - Optional

▶ Zur Prüfung des Videoeingangsfehlers Übertragung Übertragung [d][q][ ][Set ID][ ][Data][x] * Die Daten sind immer auf FF (Hex) gesetzt. Bestätigung [q][ ][Set ID][ ][OK/NG][Data][x] 0:NG 1:OK

Connecting

▶ Verbinden Sie das Kabel der Fernbedienung mit der Fernbedienungsbuchse am Produkt.

Remote control IR code

▶ Signaform-Ausgabe Einzelimpuls, Modulationssignal mit 37,917 kHz Signal bei 455 kHz  Trägerfrequenz FCAR = 1/Tc = fosc/12 Relative Einschaltdauer = T1/Tc = 1/3 ▶ Frame-Konfiguration - Erster Frame

Anschlusscode

Unterer Standardcode

Oberer Standardcode

Datencode

Datencode

C0

C1

C2

C3

C4

C5

C6

C7

C0

C1

C2

C3

C4

C5

C6

C7

D0

D1

D2

D3

D4

D5

D6

D7

D0

D1

D2

D3

D4

D5

D6

D7

• Frame-Wiederholung  Anschlusscode  ▶ Code-Wiederholung  ▶ Bit-Beschreibung   Frame-Intervall: Tf • Die Wellenform wird so lange übertragen, wie die Taste gedrückt wird. 

Code (Hex)	Funktion	Hinweis
02	VOL (▲)	Fernbedienungstaste
03	VOL (▼)	Fernbedienungstaste
40	▲	Fernbedienungstaste
41	▼	Fernbedienungstaste
06	▶	Fernbedienungstaste
07	◀	Fernbedienungstaste
08	POWER ON/OFF (Ein/Aus)	Fernbedienungstaste (POWER On/Off)
5B	EXIT	Fernbedienungstaste
09	MUTE (Lautlos)	Fernbedienungstaste
4D	EZ VIDEO(PSM)	Fernbedienungstaste
52	EZ AUDIO(SSM)	Fernbedienungstaste
98	INPUT(Quelle)	Fernbedienungstaste
5A	AV	Fernbedienungstaste
D8	S-VIDEO	Fernbedienungstaste
BF	COMPONENT	Fernbedienungstaste
C6	DVI	Fernbedienungstaste
0E	SLEEP	Fernbedienungstaste
43	MENU(Menü)	Fernbedienungstaste
44	ENTER	Fernbedienungstaste
60	PIP	Fernbedienungstaste
61	POP	Fernbedienungstaste
63	SWAP (Tausch)	Fernbedienungstaste
79	ARC(Bildformat)	Fernbedienungstaste
76	ARC(Bildformat 4:3)	Fernbedienungstaste
77	ARC(Bildformat Voll)	Fernbedienungstaste
AF	ARC(ZOOM1)	Fernbedienungstaste
54	AUTO	Fernbedienungstaste

Utilisez la méthode suivante pour connecter plusieurs appareils à un seul PC. Vous pouvez contrôler plusieurs appareils en même temps en les connectant à un seul PC. 

Cable connection.

Raccordez le câble RS-232C comme indiqué sur le schéma. * Le protocole RS-232C s'utilise lors de la communication entre le PC et l'appareil. Vous pouvez mettre l'appareil sous ou hors tension, sélectionner une source d'entrée ou régler le menu OSD depuis votre PC.  

Communication parameters

Débit en bauds : 9600 o/s (UART - émetteur-récepteur universel asynchrone) ▶ Longueur des données : 8 bits ▶ Bit de parité : Aucun ▶ Bit d'arrêt : 1 bit ▶ Contrôle de flux : Aucun ▶ Code de communication : code ASCII  Liste des références de commandes

	COMMANDE 1	COMMANDE 2	DONNÉES (Hexadéomales)
01. Power(Marche/Arrêt )	k	a	00H - 01H
02. Input Select(Sélection de l'entrée)	k	b	02H - 08H
03. Aspect Ratio(Format d'image)	k	c	01H - 06H
04. Screen Mute(Activation/Désactivation des images)	k	d	00H - 01H
05. Volume Mute(Volume muet)	k	e	00H - 01H
06. Volume Control(Contrôle du volume)	k	f	00H - 64H
07. Contrast(Contraste)	k	g	00H - 64H
08. Brightness(Luminosité)	k	h	00H - 64H
09. Color(Couleur)	k	i	00H - 64H
10. Tint(Teinte)	k	j	00H - 64H
11. Sharpness(Brillance)	k	k	00H - 64H
12. OSD Select(ACTivation/Désactivation de l'affichage à l'écran)	k	l	00H - 01H
13. Remote Lock On/Off(Blocage M-A de la télécommande)	k	m	00H - 01H
14. PIP/PBP/POP On/Off(PIP/PBP/POP Marche/Arrêt)	k	n	00H - 03H
15. PIP Position(Position PIP)	k	q	00H - 03H
16. Balance	k	t	00H - 64H
17. ACC	k	u	00H - 04H
18. PIP/PBP/POP SOURCE(SOURCE PIP/PBP/POP )	k	y	00H - 08H
19. Auto Configure(Configuration Auto.)	j	u	01H
20. Key(Clé)	m	c	Code clé
21. Tiling Mode(Mode Mosaïque)	d	d	00H - 0FH
22. Tile H Position(Position H en Mosaïque)	d	e	00H - 64H
23. Tile V Position(Position V en Mosaïque)	d	f	00H - 64H
24. Tile H Size(Taille H en Mosaïque)	d	g	00H - 64H
25. Tile V Size(Taille V en Mosaïque)	d	h	00H - 64H
26. Tile ID Set(Configuration ID en Mosaïque)	d	i	00H - 63H
27. Elapsed time return(Valeur de temps écoulé)	d	l	FFH
* 28. Light Sensor value return(Valeur de senseur lumineux)	d	m	FFH
* 29. Temperatur value return(Valeur de température)	d	n	FFH
* 30. Fan On/Off(Ventilateur Marche/Arrêt)	d	o	00H - 01H
* 31. Lamp fault check(Vérification de défaut de la lampe)	d	p	FFH
* 32. Video input fault return(Retour d'erreur d'entrée vidéo)	d	q	FFH

*: En option 

Transmission/Reception protocol

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

* [Command 1] : première commande (j, k, m, d) * [Command 2] : deuxième commande * [Set ID]: vous pouvez régler cette fonction afin de choisir le numéro d'identification de l'appareil désiré, dans le menu Spécial. La plage de réglage est comprise entre 0 et 99. Lorsque vous sélectionnez la valeur « 0 », vous commandez chacun des téléviseurs connectés. Set ID est indiqué en décimales (de 0 à 99) dans le menu et en hexadécimales (0x0 à 0x64) dans le protocole de transmission/réception. * [DATA]: pour transmettre des données de commande. Transmettre des données 'FF' pour voir l'état de commande. * [Cr]: retour de chariot Code ASCII « 0x0D » * [ ]: code ASCII espace (0x20)

Acknowledgement OK

[Command2][ ][Set ID][ ][OK][Data][x]

* L'appareil transmet un accusé de réception (ACK) de ce format quand il reçoit des données normales. Si les données reçues sont en mode lecture, il indique l'état actuel des données. Si ces données sont en mode écriture, ce sont celles de l'ordinateur.

Acknowledgement incorrect

[Command2][ ][Set ID][ ][NG][Data][x]

* L'appareil transmet un accusé de réception (ACK) de ce format quand il reçoit des erreurs de communication ou des données anormales de fonctions non viables. Données 1 : code non autorisé 2 : fonction non disponible. 3 : attendre un peu plus 

Transmission / Reception protocol

01. Power (Command: a) (Power On (Command: a))

Pour vérifier si le poste est allumé ou éteint. Transmission [k][a][ ][Set ID][ ][Data][Cr] Données 0 : Mise hors tension 1 : Mise sous tension Accusé de réception [a][ ][Set ID][ ][OK][Data][x] Pour montrer l'état de Marche ou d'Arrêt. Transmission [k][a][ ][Set ID][ ][FF][Cr] Données 0 : Mise hors tension 1 : Mise sous tension Accusé de réception [a][ ][Set ID][ ][OK][Data][x] * L'appareil transmet un accusé de réception (ACK) de ce format quand il reçoit des données normales. Si les données reçues sont en mode lecture, il indique l'état actuel des données. Si ces données sont en mode écriture, ce sont celles de l'ordinateur.

02. Input Select (Command: b) (Main Picture Input) (Input Selection (Command: b) (Main Picture Input))

Pour sélectionner l'entrée du poste. Vous pouvez également sélectionner une entrée en utilisant la touche INPUT de la télécommande. Transmission [k][b][ ][Set ID][ ][Data][Cr] Données 2 : AV 6 : RGB1 3 : S-Video 7 : RGB2 4 : Component 8 : DVI Accusé de réception [b][ ][Set ID][ ][OK][Data][x]

03. Aspect Ratio (Command: c) (Main Picture Format) (Aspect Ratio (Command: c) (Main Picture Format))

Permet de régler le format d'image. Vous pouvez également régler le format d'image à l'aide de la touche ARC (Aspect Ratio Control) de la télécommande ou à partir du menu Screen. Transmission [k][c][ ][Set ID][ ][Data][Cr] Données 1 : 4:3 (Video) 2: Plein écran (PC, Video) 3 : Spectacle (Video) 4:Zoom1(PC,Video) 5:Zoom2(Video) 6:1:1 (PC) Accusé de réception [c][ ][Set ID][ ][OK][Data][x]

04. Screen Mute (Command: d) (Screen On/Off (Command: d))

▶ Permet de commander l'affichage des images. Transmission [k][d][ ][Set ID][ ][Data][Cr] Données 0 : Activation de l'image (affichage des images) 1: Désactivation de l'image (aucune image affichée) Accusé de réception [d][ ][Set ID][ ][OK][Data][x] 

Transmission / Reception protocol

05. Volume Mute (Command: e) (Volume Mute (Command: e))

Pour contrôler si le volume muet est activé ou désactivé.

Transmission

[k][e][ ][Set ID][ ][Data][Cr] Données 0 : Volume muet activé (Volume éteint) 1 : Volume muet désactivé (Volume activé)

Acknowledgement

[e][ ][Set ID][ ][OK][Data][x] Données 0 : Volume muet activé (Volume éteint) 1 : Volume muet désactivé (Volume activé)

06. Volume Control (Command: f)

▶ Permet de régler le volume.

Transmission

[k][f][ ][Set ID][ ][Data][Cr] Données Min : 00H \~ Max : 64H (code hexadécimal)

Acknowledgement

[f][ ][Set ID][ ][OK][Data][x] Données Min : 00H \~ Max : 64H * Mise en correspondance réelle 0 : étape 0 A : étape 10 F : étape 15 10 : étape 16 64 : étape 100

07. Contrast (Command: g)

Pour régler le contraste de l'écran. Vous pouvez aussi régler le contraste dans le menu Image.

Transmission

[k][g][ ][Set ID][ ][Data][Cr] Données Min : 00H \~ Max : 64H \- Consultez le chapitre « Mise en correspondance réelle » comme indiqué ci-dessous.

Acknowledgement

[g][ ][Set ID][ ][OK][Data][x] * Mise en correspondance réelle 0 : étape 0 A : étape 10 F : étape 15 10 : étape 16 64 : étape 100

08. Brightness (Command: h)

Pour régler la luminosité de l'écran. Vous pouvez aussi régler la luminosité dans le menu Image.

Transmission

[k][h][ ][Set ID][ ][Data][Cr] Données Min : 00H \~ Max : 64H \- Consultez le chapitre « Mise en correspondance réelle » comme indiqué ci-dessous.

Acknowledgement

[h][ ][Set ID][ ][OK][Data][x] * Mise en correspondance réelle 0 : étape A: étape 10 F : étape 15 10 : étape 16 64 : étape 100 

Transmission/Reception Protocol

09. Color (Command: i) (Video only)

Pour régler la couleur de l'écran. Vous pouvez aussi régler la couleur dans le menu Image. Transmission [k][i][ ][Set ID][ ][Data][Cr] Données Min : 00H \~ Max : 64H (code hexadécimal) Accusé de réception [i][ ][Set ID][ ][OK][Data][x] Données Min : 00H \~ Max : 64H

10. Tint (Command: j) (AV/S-Video: NTSC only)

Pour régler la teinte de l'écran. Vous pouvez aussi régler la teinte dans le menu Image. Transmission [k][j][ ][Set ID][ ][Data][Cr] Données Rouge : 00H \~ Vert : 64H (code hexadécimal) Accusé de réception [j][ ][Set ID][ ][OK][Data][x] Données Rouge : 00H \~ Vert : 64H * Teinte : -50 \~ +50

11. Sharpness (Command: k) (Video only)

Pour régler la netteté de l'écran. Vous pouvez aussi régler la netteté dans le menu Image. Transmission [k][k][ ][Set ID][ ][Data][Cr] Données Min : 00H \~ Max : 64H (code hexadécimal) Accusé de réception [k][ ][Set ID][ ][OK][Data][x] Données Min : 00H \~ Max : 64H

12. OSD Select (Command: I)

Pour activer ou désactiver l'affichage à l'écran. Transmission [k][l][ ][Set ID][ ][Data][Cr] Données 0 : OSD désactivé 1 : OSD activé Accusé de réception [1][ ][Set ID][ ][OK][Data][x] Données 0 : OSD désactivé 1 : OSD activé

13. Remote Lock On/Off (Command: m)

Permet de verrouiller la télécommande ainsi que les touches du panneau avant du téléviseur. Transmission [k][m][ ][Set ID][ ][Data][Cr] Données 0 : Blocage à distance désactivé 1 : Blocage à distance activé Accusé de réception [m][ ][Set ID][ ][OK][Data][x] Données 0 : Blocage à distance désactivé 1 : Blocage à distance activé Utilisez ce mode si vous n'utilisez pas la télécommande et les touches du panneau avant du téléviseur. Lorsque l'alimentation principale est sous/hors tension, le verrouillage de la télécommande se désactive. 

Transmission / Reception Protocol

14. PIP/PBP/POP On/Off (Command: n)

Pour activer ou désactiver PIP/PBP/POP du poste. Transmission [k][n][ ][Set ID][ ][Data][Cr] Données 0 : OFF 1:PIP 2: PBP 3:POP Accusé de réception [n][ ][Set ID][ ][OK][Data][x] Données 0 : OFF 1:PIP 2: PBP 3:POP

15. PIP Position (Command: q)

Pour régler la position PIP. Transmission [k][q][ ][Set ID][ ][Data][Cr] Données 0 : en bas à droite de l'écran 1 : en bas à gauche de l'écran 2 : en haut à gauche de l'écran 3 : en haut à droite de l'écran Accusé de réception [q][ ][Set ID][ ][OK][Data][x] Données 0 : en bas à droite de l'écran 1 : en bas à gauche de l'écran 2 : en haut à gauche de l'écran 3 : en haut à droite de l'écran

16. Balance (Command: t)

▶ Pour régler la balance de bruit Transmission [k][t][ ][Set ID][ ][Data][Cr] Données Min : 00H \~ Max : 64H (code hexadécimal) Accusé de réception [t][ ][Set ID][ ][OK][Data][x] Données Min : 00H \~ Max : 64H * Balance : -50 \~ +50

17. ACC (Command: u)

Pour régler la température de couleur de l'écran. Transmission [k][u][ ][Set ID][ ][Data][Cr] Données 0 : Normal(9300K) 4 : 3600K 1 : Froid PC : 0, 2, 3, 4 2:Chaud(6500K) Video:0,1,2 3 : Utilisateur Accusé de réception [u][ ][Set ID][ ][OK][Data][x] Données 0 : Normal(9300K) 4 : 3600K 1 : Froid PC : 0, 2, 3, 4 2:Chaud(6500K) Video:0,1,2 3 : Utilisateur 

Transmission / Reception Protocol

18. PIP/PBP/POP SOURCE (Command: y)

Pour sélectionner la source du sous-écran. Transmission [k][y][ ][Set ID][ ][Data][Cr]

Données 2 : AV	6 : RGB1
3 : S-Video	7 : RGB2
4 : Component	8 : DVI

Accusé de réception [y][ ][Set ID][ ][OK][Data][x]

Données 2 : AV	6 : RGB1
3 : S-Video	7 : RGB2
4 : Component	8 : DVI

19. Auto Configure (Command: j u)

Pour régler la position de l'image et minimiser automatiquement les vibrations de l'image. Disponible uniquement en mode RGB (PC). Transmission [j][u][ ][Set ID][ ][Data][Cr] Données 1 : validation Accusé de réception [u][ ][Set ID][ ][OK][Data][x]

20. Key (Command: m c)

Permet d'envoyer le code de clef de la télécommande par infrarouge. Transmission [m][c][ ][Set ID][ ][Data][Cr] Données code de clef Accusé de réception [c][ ][Set ID][ ][OK][Data][x]

21. Tiling Mode (Command: d d)

▶ Permet de changer un mode Mosaïque. Transmission [d][d][ ][Set ID][ ][Data][x]

Données	Description
00	Le mode Mosaïque est désactivé.
12	1 x 2 mode (colonne x ligne)
13	1 x 3 mode
14	1 x 4 mode
...	...
44	4 x 4 mode

* Les données ne peuvent pas être réglées sur 0X or X0, sauf 00. Accusé de réception [d][ ][00][ ][OK/NG][Data][x]

22. Tile H Position (Command: d e)

▶ Permet de régler la position Horizontale Transmission [d][e][ ][Set ID][ ][Data][x] * La plage de données est comprise entre 00 et 64 (Hex). Accusé de réception [e][ ][Set ID][ ][OK/NG][Data][x] 

Transmission / Reception Protocol

23. Tile V Position (Command: d f)

▶ Permet de régler la position Verticale. Transmission [d][f][ ][Set ID][ ][Data][x] * La plage de données est comprise entre 00 et 64 (Hex).

Acknowledgement

[f][ ][Set ID][ ][OK/NG][Data][x]

24. Tile H Size (Command: d g)

▶ Permet de régler la taille Horizontale. Transmission [d][g][ ][Set ID][ ][Data][x] * La plage de données est comprise entre 00 et 64 (Hex).

Acknowledgment

[g][ ][Set ID][ ][OK/NG][Data][x]

25. Tile V Size (Command: d h)

▶ Permet de régler la taille Verticale. Transmission [d][h][ ][Set ID][ ][Data][x] * La plage de données est comprise entre 00 et 64 (Hex).

Acknowledgment

[h][ ][Set ID][ ][OK/NG][Data][x]

26. Tile ID Set (Command: d i)

Permet d'assigner l'identificateur Mosaïque à la fonction Mosaïque.

Transmission

[d][i][ ][Set ID][ ][Data][x] * La plage de données est comprise entre 00 et 00 x 10 en mode mosaïque.

Acknowledgment

[i][ ][Set ID][ ][OK/NG][Data][x]

27. Elapsed time return (Command: d I)

▶ Permet de lire le temps écoulé. Transmission [d][I][ ][Set ID][ ][Data][x] * Les données sont toujours FF (Hex).

Acknowledgment

[1][ ][Set ID][ ][OK/NG][Data][x]

*28. Light Sensor value Return (Command: d m) – Optional

Permet de lire la valeur du senseur lumineux afin de régler la luminosité de l'appareil selon la luminosité ambiante.

Transmission

[d][m][ ][Set ID][ ][Data][x] * Les données sont toujours FF (Hex).

Acknowledgment

[m][ ][Set ID][ ][OK/NG][Data][x] 

Transmission/Reception Protocol

*29. Temperature value Return (Command: d n) – Optional

▶ Permet de lire la valeur de la température intérieure. Transmission [d][n][ ][Set ID][ ][Data][x] * Les données sont toujours FF (Hex). Accusé de réception [n][ ][Set ID][ ][OK/NG][Data][x] Les données ont une longueur de un octet en format hexadécimal ASCII.

*30. Fan On/Off (Command: d o) – Optional

Pour activer ou désactiver le contrôle du ventilateur de l'unité. Transmission [d][o][ ][Set ID][ ][Data][x] Données 0 : Ventilateur Arrêt 1: Ventilateur Marche Accusé de réception [o][ ][Set ID][ ][OK/NG][Data][x]

*31. Lamp fault Check (Command: d p) – Optional

▶ Permet de vérifier si la lampe a un défaut. Transmission [d][p][ ][Set ID][ ][Data][x] * Les données sont toujours FF (Hex). Accusé de réception [p][ ][Set ID][ ][OK/NG][Data][x] 0 : NG 1:OK

*32. Video input fault return (Command: d q) – Optional

Pour vérifier l'erreur d'entrée vidéo. Transmission [d][q][ ][Set ID][ ][Data][x] * Les données sont toujours FF (Hex). Accusé de réception [q][ ][Set ID][ ][OK/NG][Data][x] 0:NG 1:OK

Connection

▶ Branchez la télécommande à fil sur la prise de l'appareil prévue à cet effet.

Remote control IR code

▶ Forme d'onde émise Impulsion unique, fréquence de 37.917 KHz modulée à 455 KHz  Fréquence de l'onde porteuse FPorteuse = 1/TC = FOscillateur/12 Ratio = T1/Tc = 1/3 ▶ Configuration de la trame • 1 ^ère trame

Code d'entiète

Octet personnalisé bas

Octet personnalisé haut

Données

Données

C0

C1

C2

C3

C4

C5

C6

C7

C0

C1

C2

C3

C4

C5

C6

C7

D0

D1

D2

D3

D4

D5

D6

D7

D0

D1

D2

D3

D4

D5

D6

D7

\- Trame de répétition  Code d'entête  Code de répétition  ▶ Bit description   ▶ Intervalle de trame : Tf \- Le signal est transmis tant qu'une touche est maintenue enfoncée. 

Code (Hexa)	Fonction	Remarque
02	VOL (▲)	Touche de la télécommande
03	VOL (▼)	Touche de la télécommande
40	▲	Touche de la télécommande
41	▼	Touche de la télécommande
06	►	Touche de la télécommande
07	◀	Touche de la télécommande
08	ALIMENTATION	Touche de la télécommande (Marche/Arrêt)
5B	EXIT	Touche de la télécommande
09	MUTE	Touche de la télécommande
4D	EZ VIDEO(PSM)	Touche de la télécommande
52	EZ AUDIO(SSM)	Touche de la télécommande
98	INPUT(Source)	Touche de la télécommande
5A	AV	Touche de la télécommande
D8	S-VIDEO	Touche de la télécommande
BF	COMPONENT	Touche de la télécommande
C6	DVI	Touche de la télécommande
0E	SLEEP	Touche de la télécommande
43	MENU	Touche de la télécommande
44	ENTER	Touche de la télécommande
60	PIP	Touche de la télécommande
61	POP	Touche de la télécommande
63	SWAP	Touche de la télécommande
79	ARC	Touche de la télécommande
76	ARC(4:3)	Touche de la télécommande
77	ARC(Plein)	Touche de la télécommande
AF	ARC(ZOOM1)	Touche de la télécommande
54	AUTO	Touche de la télécommande

Utilizzare questo metodo per collegare diversi prodotti ad un unico PC. È possibile controllare diversi prodotti allo stesso tempo collegandoli ad un unico PC. 

Cable connection

Collegare il cavo RS-232 come mostrato nell'illustrazione. * Il protocollo RS-232C viene impiegato per le comunicazioni tra il PC e il prodotto. È possibile accendere/spegnere il prodotto, selezionare una sorgente d'ingresso o regolare il menu OSD dal PC.  

Communication parameters

▶ Lunghezza dati: 8 bit ▶ Bit di parità: nessuno ▶ Bit di stop: 1 bit ▶ Controllo di flusso: nessuno Codice di comunicazione: codice ASCII ▶ Velocità di trasmissione in baud: 9600 bps (UART)  Elenco di riferimento dei comandi

	COMANDO1	COMANDO 2	DATI (Esadecimale)
01. Power(Alimentazione)	k	a	00H - 01H
02. Input Select(Selezione ingresso)	k	b	02H - 08H
03. Aspect Ratio(Rapporto larghezza-altezza)	k	c	01H - 06H
04. Screen Mute(Schermo silenzioso)	k	d	00H - 01H
05. Volume Mute(Volume silenzioso)	k	e	00H - 01H
06. Volume Control(Controllo volume)	k	f	00H - 64H
07. Contrast(Contrasto)	k	g	00H - 64H
08. Brightness(Luminosità)	k	h	00H - 64H
09. Color(Colore)	k	i	00H - 64H
10. Tint(Tinta)	k	j	00H - 64H
11. Sharpness(Nitidezza)	k	k	00H - 64H
12. OSD Select(Selezione OSD)	k	l	00H - 01H
13. Remote Lock On/Off(Blocco telecomando On/Off)	k	m	00H - 01H
14. PIP/PBP/POP On/Off(PIP/PBP/POP On/Off)	k	n	00H - 03H
15. PIP Position(Posizione PIP)	k	q	00H - 03H
16. Balance(Bilanciamento)	k	t	00H - 64H
17. ACC	k	u	00H - 04H
18. PIP/PBP/POP SOURCE(SORGENTE PIP/PBP/POP)	k	y	00H - 08H
19. Auto Configure(Configurazione Automatica)	j	u	01H
20. Key(Pulsante)	m	c	Codice pulsante
21. Tiling Mode(Modalità ad elementi affiancati)	d	d	00H - 0FH
22. Tile H Position(Posizione H affiancato)	d	e	00H - 64H
23. Tile V Position(Posizione V affiancato)	d	f	00H - 64H
24. Tile H Size(Dimensioni H affiancato)	d	g	00H - 64H
25. Tile V Size(Dimensioni V affiancato)	d	h	00H - 64H
26. Tile ID Set(Impostazione ID affiancato)	d	i	00H - 63H
27. Elapsed time return(Risposta tempo trascorso)	d	l	FFH
* 28. Light Sensor value return(Risposta del valore sensore luce)	d	m	FFH
* 29. Temperatur value return(Risposta del valore temperatura)	d	n	FFH
* 30. Fan On/Off(Ventola On/Off)	d	o	00H - 01H
* 31. Lamp fault check(Controllo guasto lampada)	d	p	FFH
* 32. Video in put fault return(Risposta errore ingresso video)	d	q	FFH

* : opzionale 

Transmission / reception protocol

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

* [Comando 1]: primo comando. (j, k, m, d) * [Comando 2]: secondo comando. * [Set ID] : [Imposta ID]: È possibile regolare l'impostazione ID per selezionare il numero ID del prodotto desiderato nel menu speciale. La gamma di regolazioni è 0 \~ 99. Quando si seleziona Set ID '0', si controlla ogni impianto TV collegato. Set ID viene indicato come numero decimale (0\~99) sul menu e come numero esadecimale (0x0\~0x64) nel protocollo di trasmissione/ricezione. * [DATA]: [DATI]: Per la trasmissione dei dati di comando. Trasmettere i dati 'FF' per leggere lo stato del comando. * [Cr]: Ritorno a margine codice ASCII '0x0D' * [ ]: Spazio codice ASCII (0x20)

OK acknowledgment

[Command2][ ][Set ID][ ][OK][Data][x]

* Il prodotto trasmette ACK (riconoscimento) in base al formato quando si ricevono dati normali. A questo punto se i dati sono in modalità lettura, indica i dati nello stato corrente. Se i dati sono in modalità scrittura, restituisce i dati del PC.

Error acknowledgment

[Command2][ ][Set ID][ ][NG][Data][x]

* Il prodotto trasmette ACK (riconoscimento) in base a questo formato quando si ricevono dati normali anomali da funzioni non utilizzabili o errori di comunicazione. Dati 1 : codice illegale 2 : Funzione non supportata 3 : Attendere ancora 

Transmission / reception protocol

01. Power (Command: a)

▶ Per controllare l'alimentazione On/Off dell'impianto. Trasmissione [k][a][ ][Set ID][ ][Data][Cr] Dati 0: alimentazione non attiva 1: alimentazione attiva Riconoscimento [a][ ][Set ID][ ][OK][Data][x] ▶ Per visualizzare lo stato dell'alimentazione On/Off. Trasmissione [k][a][ ][Set ID][ ][FF][Cr] Dati 0: alimentazione non attiva 1: alimentazione attiva Riconoscimento [a][ ][Set ID][ ][OK][Data][x] * Il prodotto trasmette ACK (riconoscimento) in base al formato quando si ricevono dati normali. A questo punto se i dati sono in modalità lettura, indica i dati nello stato corrente. Se i dati sono in modalità scrittura, restituisce i dati del PC.

02. Input Select (Command: b) (Main Picture Input)

Per selezionare la sorgente dell'ingresso per l'impianto. È possibile selezionare anche una sorgente d'ingresso con il pulsante INPUT sul telecomando. Trasmissione [k][b][ ][Set ID][ ][Data][Cr]

Dati	2 : AV	6 : RGB1
	3 : S-Video	7 : RGB2
	4 : Component	8 : DVI

Riconoscimento [b][ ][Set ID][ ][OK][Data][x]

03. Aspect Ratio (Command: c) (Main picture format)

Per regolare il formato dello schermo. È inoltre possibile regolare il formato dello schermo con il pulsante ARC (Aspect Ratio Control [Controllo rapporto larghezza-altezza]) presente sul telecomando o nel menu dello schermo. Trasmissione [k][c][ ][Set ID][ ][Data][Cr] Dati 1:4:3 (Video) 2: Pieno (PC, Video) 3: Spettacolo (Video) 4:Zoom1(PC,Video) 5:Zoom2(Video) 6:1:1(PC) Riconoscimento [c][ ][Set ID][ ][OK][Data][x]

04. Screen Mute (Command: d)

▶ Per selezionare la funzione schermo silenzioso on/off. Trasmissione [k][d][ ][Set ID][ ][Data][Cr] Dati 0 : Schermo silenzioso off (Immagine on) 1: Schermo silenzioso attivato (immagine disattivata) Riconoscimento [d][ ][Set ID][ ][OK][Data][x] 

Transmission / reception protocol

05. Volume Mute (Command: e)

▶ Per controllare l'opzione On/Off dell'azzeramento del volume.

Transmission

[k][e][ ][Set ID][ ][Data][Cr] Dati 0 : azzeramento volume On (volume Off) 1 : Azzeramento volume Off (volume On)

Acknowledgment

[e][ ][Set ID][ ][OK][Data][x] Dati 0 : azzeramento volume On (volume Off) 1 : Azzeramento volume Off (volume On)

06. Volume Control (Command: f)

▶ Regolare il volume.

Transmission

[k][f][ ][Set ID][ ][Data][Cr] Dati min.: 00H \~ Max: 64H (codice esadecimale)

Acknowledgment

[f][ ][Set ID][ ][OK][Data][x] Dati min.: 00H \~ Max: 64H * Rilevamento dati reali 0 : punto 0 A: punto 10 F : punto 15 10 : punto 16 64 : punto 100

07. Contrast (Command: g)

▶ Per regolare il contrasto dello schermo. È possibile regolare anche il contrasto nel menu Immagine.

Transmission

[k][g][ ][Set ID][ ][Data][Cr] Dati min.: 00H \~ Max: 64H \- Consultare il 'rilevamento dati reali' come indicato di seguito.

Acknowledgment

[g][ ][Set ID][ ][OK][Data][x] * Rilevamento dati reali 0 : punto 0 A: punto 10 F : punto 15 10 : punto 16 64 : punto 100

08. Brightness (Command: h)

▶ Per regolare la luminosità dello schermo. È possibile regolare anche la luminosità del menu Immagine.

Transmission

[k][h][ ][Set ID][ ][Data][Cr] Dati min.: 00H \~ Max: 64H \- Consultare il 'rilevamento dati reali' come indicato di seguito.

Acknowledgment

[h][ ][Set ID][ ][OK][Data][x] * Rilevamento dati reali 0 : punto A: punto 10 F : punto 15 10 : punto 16 64 : punto 100 

Transmission / Reception Protocol

09. Color (Command: i) (Video only)

▶ Per regolare il colore dello schermo. È possibile regolare anche il colore nel menu Immagine. Trasmissione [k][i][ ][Set ID][ ][Data][Cr] Dati min.: 00H \~ Max: 64H (codice esadecimale) Riconoscimento [i][ ][Set ID][ ][OK][Data][x] Dati min.: 00H \~ Max: 64H

10. Tint (Command: j) (AV/S-Video: NTSC only)

▶ Per selezionare la tinta dello schermo. È possibile regolare anche la tinta del menu Immagine. Trasmissione [k][j][ ][Set ID][ ][Data][Cr] Dati rosso: 00H \~ Verde: 64H (codice esadecimale) Riconoscimento [j][ ][Set ID][ ][OK][Data][x] Dati rosso: 00H \~ Verde: 64H * Tinta : -50 \~ +50

11. Sharpness (Command: k) (Video only)

▶ Per regolare la nitidezza dello schermò. È possibile regolare anche la nitidezza nel menu Immagine. Trasmissione [k][k][ ][Set ID][ ][Data][Cr] Dati min.: 00H \~ Max: 64H (codice esadecimale) Riconoscimento [k][ ][Set ID][ ][OK][Data][x] Dati min.: 00H \~ Max: 64H

12. OSD Select (Command: I)

▶ Per controllare l'opzione On/Off dell'OSD per l'impianto. Trasmissione [k][I][ ][Set ID][ ][Data][Cr] Dati 0: OSD Off 1: OSD On Riconoscimento [1][ ][Set ID][ ][OK][Data][x] Dati 0: OSD Off 1: OSD On

13. Remote Lock On/Off (Command: m)

Per bloccare il telecomando e i controlli del pannello frontale sull'apparecchiatura. Trasmissione [k][m][ ][Set ID][ ][Data][Cr] Dati 0: Blocco telecomando Off 1: Blocco telecomando On Riconoscimento [m][ ][Set ID][ ][OK][Data][x] Dati 0: Blocco telecomando Off 1: Blocco telecomando On Se non si utilizza il telecomando e i controlli del pannello frontale sull'apparecchiatura, utilizzare questa modalità. Quando l'alimentazione principale è attivata/disattivata, il blocco del telecomando viene disabilitato. 

Transmission / Reception Protocol

14. PIP/PBP/POP On/Off (Command: n)

▶ Per controllare l'opzione On/Off di PIP/PBP/POP dell'impianto.

Transmission

[k][n][ ][Set ID][ ][Data][Cr] Dati 0:OFF 1:PIP 2: PBP 3:POP

Acknowledgment

[n][ ][Set ID][ ][OK][Data][x] Dati 0:OFF 1:PIP 2: PBP 3:POP

15. PIP Position (Command: q)

▶ Per regolare la posizione PIP.

Transmission

[k][q][ ][Set ID][ ][Data][Cr] Dati 0 : in basso a destra sullo schermo 1: in basso a sinistra sullo schermo 2: in alto a sinistra sullo schermo 3 : in alto a destra sullo schermo

Acknowledgment

[q][ ][Set ID][ ][OK][Data][x] Dati 0 : in basso a destra sullo schermo 1 : in basso a sinistra sullo schermo 2: in alto a sinistra sullo schermo 3: in alto a destra sullo schermo

16. Balance (Command: t)

Per selezionare il bilanciamento dello suono.

Transmission

[k][t][ ][Set ID][ ][Data][Cr] Dati min.: 00H \~ Max: 64H (codice esadecimale)

Recognition

[t][ ][Set ID][ ][OK][Data][x] Dati min.: 00H \~ Max: 64H * Bilanciamento: -50 \~ +50

17. ACC (Command: u)

▶ Per regolare la temperatura del colore dello schermo.

Transmission

[k][u][ ][Set ID][ ][Data][Cr] Dati 0 : Normale (9300K) 4 : 3600K 1 : Freddo PC : 0, 2, 3, 4 2:Caldo(6500K) Video:0,1,2 3 : Utente

Recognition

[u][ ][Set ID][ ][OK][Data][x] Dati 0 : Normale (9300K) 4 : 3600K 1 : Freddo PC : 0, 2, 3, 4 2:Caldo(6500K) Video:0,1,2 3 : Utente 

Transmission / reception protocol

18. PIP/PBP/POP SOURCE (Command: y)

▶ Per selezionare la sorgente del sottoschermo. Trasmissione

[k][y][ ][Set ID][ ][Data][Cr]
Dati	2: AV	6: RGB
	3: S-Video	7: RGB
	4: Component	8: DVI

Riconoscimento

[y][ ][Set ID][ ][OK][Data][x]
Dati	2: AV	6: RGB1
	3: S-Video	7: RGB2
	4: Component	8: DVI

19. Auto Configure (Command: j u)

Per regolare la posizione dell'immagine riducendo al minimo lo sfarfallio in modo automatico. Funziona esclusivamente in modalità RGB (PC). Trasmissione [j][u][ ][Set ID][ ][Data][Cr] Dati 1: da impostare Riconoscimento [u][ ][Set ID][ ][OK][Data][x]]

20. Key (Command: m c)

▶ Per inviare il codice pulsante del telecomando all'infrarosso. Trasmissione [m][c][ ][Set ID][ ][Data][Cr] Codice pulsanti dati Riconoscimento [c][ ][Set ID][ ][OK][Data][x]

21. Tiling Mode (Command: d d)

▶ Modifica di una modalità ad elementi affiancati. Trasmissione [d][d][ ][Set ID][ ][Data][x]

Dati	Descrizione
00	La modalità ad elementi affiancati è disattivata.
12	Modalità 1 x 2 (columne x righe)
13	Modalità 1 x 3
14	Modalità 1 x 4
...	...
44	Modalità 4 x 4

* Non è possibile impostare i dati su 0x o 0X tranne 00. Riconoscimento [d][ ][00][ ][OK/NG][Data][x]

22. Tile H Position (Command: d e)

▶ Impostazione della posizione orizzontale. Trasmissione [d][e][ ][Set ID][ ][Data][x] * L'intervallo dei dati va da 00 a 64 (in un sistema esadecimale). Riconoscimento [e][ ][Set ID][ ][OK/NG][Data][x] 

Transmission / reception protocol

23. Tile V Position (Command: d f)

▶ Impostazione della posizione verticale. Trasmissione [d][f][ ][Set ID][ ][Data][x] * L'intervallo dei dati va da 00 a 64 (in un sistema esadecimale). Riconoscimento [f][ ][Set ID][ ][OK/NG][Data][x]

24. Tile H Size (Command: d g)

▶ Impostazione delle dimensioni orizzontali. Trasmissione [d][g][ ][Set ID][ ][Data][x] * L'intervallo dei dati va da 00 a 64 (in un sistema esadecimale). Riconoscimento [g][ ][Set ID][ ][OK/NG][Data][x]

25. Tile V Size (Command: d h)

▶ Impostazione delle dimensioni verticali. Trasmissione [d][h][ ][Set ID][ ][Data][x] * L'intervallo dei dati va da 00 a 64 (in un sistema esadecimale). Riconoscimento [h][ ][Set ID][ ][OK/NG][Data][x]

26. Tile ID Set (Command: d i)

▶ Assegnazione dell'ID affiancato per la funzione ad elementi affiancati. Trasmissione [d][i][ ][Set ID][ ][Data][x] * L'intervallo dei dati va dalla modalità affiancati 00 a 00 x 10. Riconoscimento [i][ ][Set ID][ ][OK/NG][Data][x]

27. Elapsed time return (Command: d l)

▶ Lettura del tempo trascorso. Trasmissione [d][I][ ][Set ID][ ][Data][x] * I dati sono sempre FF (in un sistema esadecimale). Riconoscimento [1][Set ID][OK/NG][Data][x] * 28. Light Sensor value Return(Command : d m) (Risposta del valore sensore luce (comando: d m)) - opzionale La lettura del valore del sensore luce per la regolazione della luminosità del prodotto dipende dalla luminosità circostante. Trasmissione [d][m][ ][Set ID][ ][Data][x] * I dati sono sempre FF (in un sistema esadecimale). Riconoscimento [m][ ][Set ID][ ][OK/NG][Data][x] 

Transmission / reception protocol

* 29. Temperature value Return(Command : d n) (Risposta del valore temperatura (comando: d n)) - opzionale ▶ Lettura del valore della temperatura interna. Trasmissione [d][n][ ][Set ID][ ][Data][x] * I dati sono sempre FF (in un sistema esadecimale). Riconoscimento [n][ ][Set ID][ ][OK/NG][Data][x] I dati hanno la lunghezza di un byte in formato ASCII esadecimale. * 30. Fan On/Off(Command : d o) (Ventola On/Off (comando: d o)) - opzionale ▶ Controllo della ventola da impostare su On/Off. Trasmissione [d][o][ ][Set ID][ ][Data][x] Dati 0: Ventola Off 1: Ventola On Riconoscimento [o][ ][Set ID][ ][OK/NG][Data][x] * 31. Lamp fault Check(Command : d p) (Controllo guasto lampada (comando: d p)) - opzionale ▶ Controllo del guasto lampada. Trasmissione [d][p][ ][Set ID][ ][Data][x] * I dati sono sempre FF (in un sistema esadecimale). Riconoscimento [p][ ][Set ID][ ][OK/NG][Data][x] 0:NG 1:OK *32. Video input fault return(Command : d q) (Risposta errore ingresso video (comando: d q)) - opzionale ▶ Per verificare l'errore dell'ingresso video. Trasmissione [d][q][ ][Set ID][ ][Data][x] * I dati sono sempre FF (in un sistema esadecimale). Riconoscimento [q][ ][Set ID][ ][OK/NG][Data][x] 0:NG 1:OK

Connection methods

▶ Collegare il telecomando a cavo all'apposita porta presente sul prodotto.

Remote control IR code

▶ Forma d'onda in uscita impulso singolo modulato con segnale da 37.917 KHz a 455 KHz  Frequenza portante FCAR = 1/Tc = fosc/12 Fattore di utilizzazione = T1/Tc = 1/3 ▶ Configurazione di sequenza \- 1° sequenza

Codice guida

Ottetto personalizzato basso

Ottetto personalizzato alto

Codice dati

Codice dati

C0

C1

C2

C3

C4

C5

C6

C7

C0

C1

C2

C3

C4

C5

C6

C7

D0

D1

D2

D3

D4

D5

D6

D7

D0

D1

D2

D3

D4

D5

D6

D7

\- Sequenza di ripetizione  Codice guida  Codice di ripetizione  ▶ Descrizione bit   ▶ Intervallo di sequenza: Tf \- La forma d'onda viene trasmessa fino a quando sono premuti i pulsanti. 

Codice (Esadec.)	Funzione	Nota
02	VOL (▲)	Pulsante R/C
03	VOL (▼)	Pulsante R/C
40	▲	Pulsante R/C
41	▼	Pulsante R/C
06	►	Pulsante R/C
07	◄	Pulsante R/C
08	POWER ON/OFF	Pulsante R/C (POWER On/Off)
5B	EXIT	Pulsante R/C
09	MUTE	Pulsante R/C
4D	EZ VIDEO(PSM)	Pulsante R/C
52	EZ AUDIO(SSM)	Pulsante R/C
98	INPUT(Source)	Pulsante R/C
5A	AV	Pulsante R/C
D8	S-VIDEO	Pulsante R/C
BF	COMPONENT	Pulsante R/C
C6	DVI	Pulsante R/C
0E	SLEEP [spegnimento]	Pulsante R/C
43	MENU	Pulsante R/C
44	ENTER	Pulsante R/C
60	PIP	Pulsante R/C
61	POP	Pulsante R/C
63	SWAP	Pulsante R/C
79	ARC	Pulsante R/C
76	ARC(4:3)	Pulsante R/C
77	ARC(Pieno)	Pulsante R/C
AF	ARC(ZOOM1)	Pulsante R/C
54	AUTO	Pulsante R/C

Utilice este método para conectar varios productos a un solo PC. Puede controlar varios productos simultáneamente mediante su conexión a un solo PC. 

Cable connection

Conecte el cable RS-232C tal como se muestra en la imagen. * El protocolo RS-232C se utiliza para comunicaciones entre el PC y el producto. Puede apagar y encender el producto, seleccionar una fuente de entrada o ajustar el menú OSD desde el PC.  

Communication parameter

▶ Velocidad de línea en baudios: 9600 bps (UART) ▶ Longitud de los datos: 8 bits ▶ Bit de paridad: ninguno ▶ Bit de parada: 1 bit ▶ Control de flujo: ninguno ▶ Código de comunicación: código ASCII  Lista de referencia de comandos

	COMMAND1	COMMAND2	DATA(Hexa)
01. Power(Encendido)	k	a	00H - 01H
02. Input Select(Selección de entrada)	k	b	02H - 08H
03. Aspect Ratio(Relación de aspecto)	k	c	01H - 06H
04. Screen Mute(Silencio de pantalla)	k	d	00H - 01H
05. Volume Mute(Silencio de volumen)	k	e	00H - 01H
06. Volume Control(Control de volumen)	k	f	00H - 64H
07. Contrast(Contraste)	k	g	00H - 64H
08. Brightness(Luminosidad)	k	h	00H - 64H
09. Color	k	i	00H - 64H
10. Tint(Tinte)	k	j	00H - 64H
11. Sharpness(Definición)	k	k	00H - 64H
12. OSD Select(Selección)	k	l	00H - 01H
13. Remote Lock On/Off(Bloqueo/Desbloqueo del mando a distancia)	k	m	00H - 01H
14. PIP/PBP/POP On/Off(Activación/Desactivación de PIP/PBP/POP)	k	n	00H - 03H
15. PIP Position(Posición PIP)	k	q	00H - 03H
16. Balance	k	t	00H - 64H
17. ACC	k	u	00H - 04H
18. PIP/PBP/POP SOURCE(FUENTE PIP/PBP/POP )	k	y	00H - 08H
19. Auto Configure(Config. automático)	j	u	01H
20. Key(Clave)	m	c	Código de clave
21. Tiling Mode(Modo mosaico)	d	d	00H - 0FH
22. Tile H Position(Posición H en mosaico)	d	e	00H - 64H
23. Tile V Position(Posición V en mosaico)	d	f	00H - 64H
24. Tile H Size(Tamaño H en mosaico)	d	g	00H - 64H
25. Tile V Size(Tamaño V en mosaico)	d	h	00H - 64H
26. Tile ID Set(Definir ID en mosaico)	d	i	00H - 63H
27. Elapsed time return(Valor de tiempo transcurrido)	d	l	FFH
*28. Light Sensor value return(Valor de sensor luminoso)	d	m	FFH
*29. Temperatur value return(Valor de temperatura)	d	n	FFH
*30. Fan On/Off(Ventilador conectado/desconectado)	d	o	00H - 01H
*31. Lamp fault check(Comprobación de fallos de la lámpara)	d	p	FFH
*32. Video input fault return(Respuesta de fallo de entrada de vídeo)	d	q	FFH

* : opcional 

Transmission and reception protocol

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

* [Command 1]: primer comando (j, k, m, d) * [Command 2]: segundo comando. * [Set ID]: puede ajustar Set ID para seleccionar el número de ID del producto que desee en el menú Especial. El rango de ajuste es 0 \~ 99. Al seleccionar Set ID '0', controlará todos los monitores conectados. Set ID se expresa como un número decimal (0\~99) en el menú y como un número hexadecimal (0x0\~0x64) en el protocolo de transmisión y recepción. * [DATA]: para transmitir los datos del comando. Transmita datos 'FF' para leer el estado del comando. * [Cr]: retorno de carro Código ASCII '0x0D' * [ ]: espacio en código ASCII (0x20)'

Confirmation of correct

[Command2][ ][Set ID][ ][OK][Data][x]

* El producto transmite un ACK (confirmación) basado en este formato al recibir datos normales. En ese momento, si los datos son datos en modo de lectura, indicará los datos del estado actual. Si los datos son datos en modo de escritura, devolverá los datos al PC.

Error confirmation

[Command2][ ][Set ID][ ][NG][Data][x]

* El producto transmite un ACK (confirmación) basado en este formato al recibir datos incorrectos de funciones no viables o comunicaciones de error. Data 1 : código no admitido 2 : función no admitida 3: solicitud de ampliación de espera 

Transmission and reception protocol

01. Power (Command: a)

Para controlar el encendido y apagado de la unidad. Transmisión [k][a][ ][Set ID][ ][Data][Cr] Data 0: Apagado 1: encendido Confirmación [a][ ][Set ID][ ][OK][Data][x] Para mostrar el estado de encendido o apagado. Transmisión [k][a][ ][Set ID][ ][FF][Cr] Data 0: Apagado 1: encendido Confirmación [a][ ][Set ID][ ][OK][Data][x] * El producto transmite un ACK (confirmación) basado en este formato al recibir datos normales. En ese momento, si los datos son datos en modo de lectura, indicará los datos del estado actual. Si los datos son datos en modo de escritura, devolverá los datos al PC.

02. Input Select (Command: b) (Main Picture Input)

Para seleccionar la fuente de entrada de la unidad. También puede seleccionar una fuente de entrada utilizando el botón INPUT del mando a distancia. Transmisión [k][b][ ][Set ID][ ][Data][Cr]

Data 2:AV	6:RGB1
3:S-Video	7:RGB2
4:Component	8:DVI

03. Aspect Ratio (Command: c) (Main Picture Format)

Para ajustar el formato de la pantalla. También puede ajustar el formato de la pantalla con el botón ARC (Control de relación de aspecto) desde el mando a distancia o en el menú Screen.

Transmission

[k][c][ ][Set ID][ ][Data][Cr] Data 1:4:3 (Video) 2: Completo (PC, Video) 3 : Spectacle (Video) 4:Zoom1(PC,Video) 5:Zoom2(Video) 6:1:1(PC)

Confirmation

[c][ ][Set ID][ ][OK][Data][x]

04. Screen Mute (Command: d)

Para seleccionar la activación o desactivación del silencio de pantalla.

Transmission

[k][d][ ][Set ID][ ][Data][Cr] Data 0 : Silencio de pantalla desactivado (Imagen sí) 1: Silencio de pantalla activado (Imagen no)

Confirmation

[d][ ][Set ID][ ][OK][Data][x] Confirmación [b][ ][Set ID][ ][OK][Data][x] 

Transmission and reception protocol

05. Volume Mute (Command: e)

Para controlar la activación y desactivación del silencio de volumen.

Transmission

[k][e][ ][Set ID][ ][Data][Cr] Data 0: silencio de volumen activado (volumen apagado) 1: silencio de volumen desactivado (volumen encendido)

Confirmation

[e][ ][Set ID][ ][OK][Data][x] Data 0: silencio de volumen activado (volumen apagado) 1: silencio de volumen desactivado (volumen encendido)

06. Volume Control (Command: f)

▶ Ajuste el volumen.

Transmission

[k][f][ ][Set ID][ ][Data][Cr] Data Min: 00H \~ Max: 64H (código hexadecimal)

Confirmation

[f][ ][Set ID][ ][OK][Data][x] Data Min: 00H \~ Max: 64H * Asignación de datos reales 0: Paso 0 A: Paso 10 F : Paso 15 10: Paso 16 64: Paso 100

07. Contrast (Command: g)

Para ajustar el contraste de la pantalla. También puede ajustar el contraste en el menú Imagen.

Transmission

[k][g][ ][Set ID][ ][Data][Cr] Data Min: 00H \~ Max: 64H \- Consulte la 'Asignación de datos reales' tal como se muestra más abajo.

Acknowledgment

[g][ ][Set ID][ ][OK][Data][x] * Asignación de datos reales 0 : Paso 0 A: Paso 10 F: Paso 15 10: Paso 16 64: Paso 100

08. Brightness (Command: h)

Para ajustar el brillo de la pantalla. También puede ajustar la luminosidad en el menú Imagen.

Transmission

[k][h][ ][Set ID][ ][Data][Cr] Data Min: 00H \~ Max: 64H \- Consulte la 'Asignación de datos reales' tal como se muestra más abajo.

Acknowledgment

[h][ ][Set ID][ ][OK][Data][x] * Asignación de datos reales 0 : Paso A: Paso 10 F: Paso 15 10: Paso 16 64: Paso 100 

Transmission and reception protocol

09. Color (Command: i) (Video only)

Para ajustar el color de la pantalla. También puede ajustar el color en el menú Imagen.

Transmission

[k][i][ ][Set ID][ ][Data][Cr] Data Min: 00H \~ Max: 64H (código hexadecimal)

Acknowledgment

[i][ ][Set ID][ ][OK][Data][x]

10. Tint (Command: j) (AV/S-Video: NTSC only)

Para ajustar el tinte de la pantalla. También puede ajustar el tinte en el menú Imagen.

Transmission

[k][j][ ][Set ID][ ][Data][Cr] Data Rojo: 00H \~ Verde: 64H (código hexadecimal)

Acknowledgment

[j][ ][Set ID][ ][OK][Data][x] Data Rojo: 00H \~ Verde: 64H * Tinte : -50 \~ +50

11. Sharpness (Command: k) (Video only)

Para ajustar la definición de la pantalla. También puede ajustar la definición en el menú Imagen.

Transmission

[k][k][ ][Set ID][ ][Data][Cr] Data Min: 00H \~ Max: 64H (código hexadecimal)

Acknowledgment

[k][ ][Set ID][ ][OK][Data][x] Data Min: 00H \~ Max: 64H

12. OSD Select (Command: I)

Para habilitar o deshabilitar el control de OSD de la unidad.

Transmission

[k][I][ ][Set ID][ ][Data][Cr] Data 0: OSD desactivado 1: OSD activado

Acknowledgement

[1][ ][Set ID][ ][OK][Data][x] Data 0: OSD desactivado 1: OSD activado

13. Remote Lock On/Off (Command: m)

Para bloquear el mando a distancia y los controles del panel frontal de la unidad.

Transmission

[k][m][ ][Set ID][ ][Data][Cr] Data 0: bloqueo mando a distancia desactivado 1: bloqueo mando a distancia activado

Acknowledgement

[m][ ][Set ID][ ][OK][Data][x] Data 0: bloqueo mando a distancia desactivado 1: bloqueo mando a distancia activado ▶ Si no utiliza el mando a distancia ni los controles del panel frontal de la unidad, utilice este modo. Si la alimentación está activada o desactivada, se libera el bloqueo del mando a distancia. 

Transmission/Reception Protocol

14. PIP/PBP/POP On/Off (Command: n)

Para controlar la activación y la desactivación de PIP/PBP/POP de la unidad.

Transmission

[k][n][ ][Set ID][ ][Data][Cr] Data 0 : DESACTIVADO 1 : PIP 2 : PBP 3:POP

Acknowledgement

[n][ ][Set ID][ ][OK][Data][x] Data 0 : DESACTIVADO 1:PIP 2: PBP 3:POP

15. PIP Position (Command: q)

Para ajustar la posición PIP.

Transmission

[k][q][ ][Set ID][ ][Data][Cr] Data 0:esquina inferior derecha de la pantalla 1:esquina inferior izquierda de la pantalla 2:esquina superior izquierda de la pantalla 3:esquina superior derecha de la pantalla

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x] Data 0:esquina inferior derecha de la pantalla 1:esquina inferior izquierda de la pantalla 2:esquina superior izquierda de la pantalla 3:esquina superior derecha de la pantalla

16. Balance (Command: t)

Para ajustar el balance de la sonido. Transmisión [k][t][ ][Set ID][ ][Data][Cr] Data Min: 00H \~ Max: 64H (código hexadecimal)

Acknowledgement

[t][ ][Set ID][ ][OK][Data][x] Data Min: 00H \~ Max: 64H * Balance : -50 \~ +50

17. ACC (Command: u)

Para ajustar la temperatura de color de la pantalla. Transmisión [k][u][ ][Set ID][ ][Data][Cr] Data 0 : Flat (9300K) 4 : 3600K 1 : Frío PC : 0, 2, 3, 4 2 : Caliente (6500K) Video : 0, 1, 2 3 : Usuario

Confirmation

[u][ ][Set ID][ ][OK][Data][x] Data 0 : Flat (9300K) 4 : 3600K 1 : Frío PC : 0, 2, 3, 4 2 : Caliente (6500K) Video : 0, 1, 2 3 : Usuario 

Transmission and reception protocol

18. PIP/PBP/POP SOURCE (Command: y)

Para seleccionar la fuente de la subpantalla. Transmisión [k][y][ ][Set ID][ ][Data][Cr]

Data 2:AV	6:RGB1
3:S-Video	7:RGB2
4:Component	8:DVI

Confirmación [y][ ][Set ID][ ][OK][Data][x]

Data 2:AV	6:RGB1
3:S-Video	7:RGB2
4:Component	8:DVI

19. Auto Configure (Command: j u)

Para ajustar la posición de la imagen y minimizar las vibraciones automáticamente. Funciona solamente en modo RGB(PC). Transmisión [j][u][ ][Set ID][ ][Data][Cr] Data 1: Validación Confirmación [u][ ][Set ID][ ][OK][Data][x]

20. Key (Command: m c)

Para enviar el código de clave del mando a distancia por infrarrojos. Transmisión [m][c][ ][Set ID][ ][Data][Cr] Data Código de clave Confirmación [c][ ][Set ID][ ][OK][Data][x]

21. Tiling Mode (Command: d d)

▶ Cambia un modo mosaico. Transmisión [d][d][ ][Set ID][ ][Data][x]

Data	Descripción
00	Modo mosaico desactivado.
12	Modo 1 x 2 (columna x fila)
13	Modo 1 x 3
14	Modo 1 x 4
...	...
44	Modo 4 x 4

* Los datos no pueden ajustarse en 0X o X0, excepto 00. Confirmación [d][ ][00][ ][OK/NG][Data][x]

22. Tile H Position (Command: d e)

▶ Ajusta la posición horizontal. Transmisión [d][e][ ][Set ID][ ][Data][x] * El rango de datos varía entre 00 y 64 (Hex). Confirmación [e][ ][Set ID][ ][OK/NG][Data][x] 

Transmission and reception protocol

23. Tile V Position (Command: d f)

▶ Ajusta la posición vertical. Transmisión [d][f][ ][Set ID][ ][Data][x] * El rango de datos varía entre 00 y 64 (Hex). Confirmación [f][ ][Set ID][ ][OK/NG][Data][x]

26. Tile ID Set (Command: d i)

▶ Asigna un ID de mosaico a la función mosaico. Transmisión [d][i][ ][Set ID][ ][Data][x] * El rango de datos varía entre 00 y 00 x 10 en modo mosaico. Confirmación [i][ ][Set ID][ ][OK/NG][Data][x]

24. Tile H Size (Command: d g)

▶ Ajusta el tamaño horizontal. Transmisión [d][g][ ][Set ID][ ][Data][x] * El rango de datos varía entre 00 y 64 (Hex).

27. Elapsed time return (Command: d l)

▶ Lee el tiempo transcurrido. Transmisión [d][I][ ][Set ID][ ][Data][x] * Los datos son siempre FF (Hex). Confirmación [g][ ][Set ID][ ][OK/NG][Data][x] Confirmación [1][ ][Set ID][ ][OK/NG][Data][x]

25. Tile V Size (Command: d h)

▶ Ajusta el tamaño vertical. Transmisión [d][h][ ][Set ID][ ][Data][x] * El rango de datos varía entre 00 y 64 (Hex).

*28. Light Sensor value Return (Command: d m) - optional

▶ Lee el valor del sensor luminoso para ajustar la luminosidad del producto en función de la luminosidad ambiente. Transmisión [d][m][ ][Set ID][ ][Data][x] * Los datos son siempre FF (Hex). Confirmación [h][ ][Set ID][ ][OK/NG][Data][x] Confirmación [m][ ][Set ID][ ][OK/NG][Data][x] 

Transmission and reception protocol

*29. Temperature value

Return(Command : d n) - opcional (Valor de temperatura(Comando: d n)) ▶ Lée el valor de temperatura interna. Transmisión [d][n][ ][Set ID][ ][Data][x] * Los datos son siempre FF (Hex). Confirmación [n][ ][Set ID][ ][OK/NG][Data][x] Los datos tienen una longitud de 1 en formato hexadecimal ASCII.

*30. Fan On/Off (Command: d o)

(Ventilador conectado/desconectado (Comando: d o)) - opcional Para habilitar o deshabilitar el control del ventilador de la unidad. Transmisión [d][o][ ][Set ID][ ][Data][x] Data 0: Ventilador desconectado 1: Ventilador conectado Confirmación [o][ ][Set ID][ ][OK/NG][Data][x]

*31. Lamp fault Check (Command: d p)

(Comprobación de fallos de la lámpara(Comando: d p)) - opcional ▶ Realiza la comprobación de fallos de la lámpara. Transmisión [d][p][ ][Set ID][ ][Data][x] * Los datos son siempre FF (Hex). Confirmación [p][ ][Set ID][ ][OK/NG][Data][x] 0:NG 1:OK

*32. Video input fault return (Command: d q) (Lamp fault check (Command: d q)) - optional

Para comprobar los fallos de la entrada de vídeo. Transmisión [d][q][ ][Set ID][ ][Data][x] * Los datos son siempre FF (Hex). Confirmación [q][ ][Set ID][ ][OK/NG][Data][x] 0:NG 1:OK

How to connect

▶ Conecte el mando a distancia cableado al puerto del mando a distancia del producto.

Remote control IR code

▶ Forma de onda en la salida impulso único, modulado con señal de 37,917 Khz. a 455 Khz.  Frecuencia portadora FCAR = 1/Tc = fosc/12 Relación de trabajo = T1/Tc = 1/3 ▶ Configuración del cuadro \- 1er cuadro

Código del cable conductor

Bajo código personalizado

Alto código personalizado

Código de datos

Código de datos

C0

C1

C2

C3

C4

C5

C6

C7

C0

C1

C2

C3

C4

C5

C6

C7

D0

D1

D2

D3

D4

D5

D6

D7

D0

D1

D2

D3

D4

D5

D6

D7

\- Repetir cuadro  ▶ Código del cable conductor  ▶ Código de repetición  ▶ Descripción de bits   ▶ Intervalo de cuadros: Tf \- La forma de onda se transmite siempre que esté pulsada una tecla. 

Código (Hexa)	Función	Nota
02	VOL (▲)	Botón R/C
03	VOL (▼)	Botón R/C
40	▲	Botón R/C
41	▼	Botón R/C
06	▶	Botón R/C
07	◀	Botón R/C
08	ENCENDIDO/APAGADO	Botón R/C (Encendido/apagado)
5B	EXIT	Botón R/C
09	MUTE	Botón R/C
4D	EZ VIDEO(PSM)	Botón R/C
52	EZ AUDIO(SSM)	Botón R/C
98	INPUT(Source)	Botón R/C
5A	AV	Botón R/C
D8	S-VIDEO	Botón R/C
BF	COMPONENT	Botón R/C
C6	DVI	Botón R/C
0E	SLEEP	Botón R/C
43	MENU(MENÚ)	Botón R/C
44	ENTER	Botón R/C
60	PIP	Botón R/C
61	POP	Botón R/C
63	SWAP	Botón R/C
79	ARC	Botón R/C
76	ARC(4:3)	Botón R/C
77	ARC(Completo)	Botón R/C
AF	ARC(ZOOM1)	Botón R/C
54	AUTO	Botón R/C

Use este método para conectar vários aparelhos a um único PC. Você pode controlar vários aparelhos de uma vez conectando-os a um único PC. 

Connecting the cable

Conectando o cabo RS-232C como mostrado na figura. * O protocolo RS-232C é usado para a comunicação entre o PC e o aparelho. Você pode ligar/desligar o aparelho, selecionar uma fonte de entrada ou ajustar o menu OSD do PC.  

Communication parameter

▶ Taxa de Transmissão: 9600bps (UART) ▶ Comprimento de Dados: 8 bits ▶ Bits de Paridade: Nenhum ▶ Bit de parada: 1 bit ▶ Controle de Fluxo: Nenhum ▶ Código de Comunicação: Código ASCII  Lista de referência de comandos

	COMANDO1	COMANDO2	DADOS (Hexa)
01. Power(Ligar/desligar)	k	a	00H - 01H
02. Input Select(Seleção de Entrada)	k	b	02H - 08H
03. Aspect Ratio(Taxa de Proporção)	k	c	01H - 06H
04. Screen Mute(Tela Sem Áudio)	k	d	00H - 01H
05. Volume Mute(Volume Sem Áudio)	k	e	00H - 01H
06. Volume Control(Controle de Volume)	k	f	00H - 64H
07. Contrast(Contraste)	k	g	00H - 64H
08. Brightness(Brilho)	k	h	00H - 64H
09. Color(Cor)	k	i	00H - 64H
10. Tint(Colorir)	k	j	00H - 64H
11. Sharpness(Nitidez)	k	k	00H - 64H
12. OSD Select(Seleção de OSD)	k	l	00H - 01H
13. Remote Lock On/Off(Bloqueio ativado/desativado)	k	m	00H - 01H
14. PIP/PBP/POP On/Off(PIP/PBP/POP ativado/desativado)	k	n	00H - 03H
15. PIP Position(Posição PIP)	k	q	00H - 03H
16. Balance(Balanço)	k	t	00H - 64H
17. ACC	k	u	00H - 04H
18. PIP/PBP/POP SOURCE(EMISSÃO PIP/PBP/POP)	k	y	00H - 08H
19. Auto Configure(Configuração Automática)	j	u	01H
20. Key(Tecla)	m	c	Código da Tecla
21. Tiling Mode(Modo lado a lado)	d	d	00H - 0FH
22. Tile H Position(Lado a lado na posição horizontal)	d	e	00H - 64H
23. Tile V Position(Lado a lado na posição vertical)	d	f	00H - 64H
24. Tile H Size(Tamanho horizontal de lado a lado)	d	g	00H - 64H
25. Tile V Size(Tamanho vertical de lado a lado)	d	h	00H - 64H
26. Tile ID Set(ID Set de lado a lado)	d	i	00H - 63H
27. Elapsed time return(Retorno de tempo decorrido)	d	l	FFH
* 28. Light Sensor value return(Retorno do valor do sensor de iluminação)	d	m	FFH
* 29. Temperatur value return(Retorno do valor de temperatura)	d	n	FFH
* 30. Fan On/Off(Ventilador Ativado/Desativado)	d	o	00H - 01H
* 31. Lamp fault check(Verificação de defeitos da lâmpada)	d	p	FFH
* 32. Video input fault return(Retorno de falha na entrada de vídeo)	d	q	FFH

*: opcional 

Transmission/reception protocol

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

* [Command 1]: Primeiro comando. (j,k,m,d) * [Command 2]: Segundo comando. * [Set ID]: Você pode ajustar a opção Set ID para escolher o número de identificação do aparelho desejado no menu Especial. O ajuste varia de 0 a 99, aproximadamente. Ao selecionar '0' em Set ID (identificação), cada aparelho de TV conectado é controlado. A opção Set ID é indicada como decimal (0\~99) no menu e como Hexa decimal (0x0\~0x64) no protocolo de transmissão/recepção. * [DATA]: Para transmitir dados de comando. Transmitir dados 'FF' para ler o status de comando. * [Cr]: Retorno de carro Código ASCII '0x0D' * [ ]: Código ASCII espaço (0x20)

OK confirmation

[Command2][ ][Set ID][ ][OK][Data][x]

* O aparelho transmite uma ACK (confirmação) com base nesse formato ao receber dados normais. Nesse momento, se os dados estiverem no modo de leitura de dados, indicará o status atual dos dados. Se os dados estiverem no modo de gravação, os dados do computador serão retornados.

Error confirmation

[Command2][ ][Set ID][ ][NG][Data][x]

* O aparelho transmite uma ACK (confirmação) com base nesse formato ao receber dados anormais de funções não viáveis ou erros de comunicação. Data 1 : Código ilegal 2 : Função sem suporte 3 : Aguarde alguns minutos 

Transmission/Reception Protocol

01. Power (Command: a) (Power On/Off (Command: a))

Para controlar a função ligar/desligar do monitor. Transmissão [k][a][ ][Set ID][ ][Data][Cr] Data 0: Desligar 1: Ligar Confirmação [a][ ][Set ID][ ][OK][Data][x] Para mostrar o status de Ligar/desligar. Transmissão [k][a][ ][Set ID][ ][FF][Cr] Data 0: Desligar 1: Ligar Confirmação [a][ ][Set ID][ ][OK][Data][x] * O aparelho transmite uma ACK (confirmação) com base nesse formato ao receber dados normais. Nesse momento, se os dados estiverem no modo de leitura de dados, indicará o status atual dos dados. Se os dados estiverem no modo de gravação, os dados do computador serão retornados.

02. Input Select (Command: b) (Main Picture Input) (Input Selection (Command: b) (Main Picture Input))

Para selecionar a fonte de entrada do monitor. Você também pode selecionar uma fonte de entrada usando o botão INPUT do controle remoto da TV. Transmissão [k][b][ ][Set ID][ ][Data][Cr] Data 2:AV 6:RGB1 3 : S-Video 7 : RGB2 4 : Component 8 : DVI Confirmação [b][ ][Set ID][ ][OK][Data][x]

03. Aspect Ratio (Command: c) (Main Picture Format) (Aspect Ratio (Command: c) (Main Picture Format))

Para ajustar o formato da tela. Você também pode ajustar o formato da tela usando o botão ARC (Aspect Ratio Control, controle de proporção de vídeo) no controle remoto ou no Menu Screen (Menu de tela). Transmissão [k][c][ ][Set ID][ ][Data][Cr] Data 1:4:3 (Video) 2: Completo (PC, Video) 3 : Espéctac. (Video) 4:Zoom1(PC,Video) 5:Zoom2(Video) 6:1:1(PC) Confirmação [c][ ][Set ID][ ][OK][Data][x]

04. Screen Mute (Command: d) (Screen Mute (Command: d))

Para ativar/desativar o recurso tela sem áudio. Transmissão [k][d][ ][Set ID][ ][Data][Cr] Data 0 : Recurso tela sem áudio desativado (recurso de imagem ativado) 1 : Recurso tela sem áudio ativado (recurso de imagem desativado) Confirmação [d][ ][Set ID][ ][OK][Data][x] 

Transmission/Reception Protocol

05. Volume Mute (Command: e) (Volume Mute (Command: e))

Para ativar/desativar o recurso volume sem áudio.

Transmission

[k][e][ ][Set ID][ ][Data][Cr] Data 0 : Recurso volume sem áudio ativado (Volume desativado) 1: Recurso volume sem áudio desativado (Volume ativado)

Confirmation

[e][ ][Set ID][ ][OK][Data][x] Data 0 : Recurso volume sem áudio ativado (Volume desativado) 1: Recurso volume sem áudio desativado (Volume ativado)

06. Volume Control (Command: f) (Volume Control (Command: f))

▶ Ajuste o volume.

Transmission

[k][f][ ][Set ID][ ][Data][Cr] Data Mín: 00H \~ Máx: 64H (Código hexadecimal)

Confirmation

[f][ ][Set ID][ ][OK][Data][x] Data Mín: 00H \~ Máx: 64H * Mapeamento de dados reais 0 : Etapa 0 A: Etapa 10 F : Etapa 15 10: Etapa 16 64 : Etapa 100

07. Contrast (Command: g) (Contrast (Command: g))

Para ajustar o contraste da tela. Você também pode ajustar o contraste no menu Imagem.

Transmission

[k][g][ ][Set ID][ ][Data][Cr] Data Mín: 00H \~ Máx: 64H \- Consulte 'Mapeamento de dados reais' como mostrado a seguir.

Confirmation

[g][ ][Set ID][ ][OK][Data][x] * Mapeamento de dados reais 0 : Etapa 0 A: Etapa 10 F : Etapa 15 10: Etapa 16 64: Etapa 100

08. Brightness (Command: h)

Para ajustar o brilho da tela. Você também pode ajustar o brilho no menu Imagem.

Transmission

[k][h][ ][Set ID][ ][Data][Cr] Data Mín: 00H \~ Máx: 64H \- Consulte 'Mapeamento de dados reais' como mostrado a seguir.

Confirmation

[h][ ][Set ID][ ][OK][Data][x] * Mapeamento de dados reais 0 : Etapa A: Etapa 10 F : Etapa 15 10 : Etapa 16 64 : Etapa 100 

Transmission/Reception Protocol

09. Color (Command: i) (Video only)

Para ajustar a cor da tela. Você também pode ajustar a cor no menu Imagem.

Transmission

[k][i][ ][Set ID][ ][Data][Cr] Data Mín: 00H \~ Máx: 64H (Código hexadecimal)

Confirmation

[i][ ][Set ID][ ][OK][Data][x] Data Mín: 00H \~ Máx: 64H

10. Tint (Command: j) (AV/S-Video: NTSC only)

Para ajustar a tonalidade da tela. Você também pode ajustar a tonalidade no menu Imagem.

Transmission

[k][j][ ][Set ID][ ][Data][Cr] Data Vermelho : 00H \~ Verde: 64H (Código hexadecimal)

Confirmation

[j][ ][Set ID][ ][OK][Data][x] Data Vermelho : 00H \~ Verde: 64H * Colorir : -50 \~ +50

11. Sharpness (Command: k) (Video only)

Para ajustar a nitidez da tela. Você também pode ajustar a nitidez no menu Imagem.

Transmission

[k][k][ ][Set ID][ ][Data][Cr] Data Mín: 00H \~ Máx: 64H (Código hexadecimal)

Confirmation

[k][ ][Set ID][ ][OK][Data][x] Data Mín: 00H \~ Máx: 64H

12. OSD Select (Command: I)

Para controlar o OSD ativado/desativado no aparelho.

Transmission

[k][l][ ][Set ID][ ][Data][Cr] Data 0: OSD desativado 1: OSD ativado

Confirmation

[1][ ][Set ID][ ][OK][Data][x] Data 0: OSD desativado 1: OSD ativado

13. Remote Lock On/Off (Command: m)

Para bloquear o controlo remoto e os controlos do painel frontal do televisor.

Transmission

[k][m][ ][Set ID][ ][Data][Cr] Data 0: Bloqueio desativado 1: Bloqueio ativado

Confirmation

[m][ ][Set ID][ ][OK][Data][x] Data 0: Bloqueio desativado 1: Bloqueio ativado Se não está a utilizar o controlo remoto e os controlos do painel frontal do televisor, utilize este modo. Quando a fonte de alimentação principal está ligada/desligada, o bloqueio do controlo remoto é retirado. 

Transmission/Reception Protocol

14. PIP/PBP/POP On/Off (Command: n)

Para controlar a função PIP/PBP/POP On/Off do monitor.

Transmission

[k][n][ ][Set ID][ ][Data][Cr] Data 0 : DESATIVADO 1:PIP 2: PBP 3:POP

Confirmation

[n][ ][Set ID][ ][OK][Data][x] Data 0 : DESATIVADO 1:PIP 2: PBP 3:POP

15. PIP Position (Command: q)

Para ajustar a posição PIP.

Transmission

[k][q][ ][Set ID][ ][Data][Cr] Data 0 : Parte inferior do lado direito da tela 1: Parte inferior do lado esquerdo da tela 2:Parte superior do lado esquerdo da tela 3: Parte superior do lado direito da tela

Confirmation

[q][ ][Set ID][ ][OK][Data][x] Data 0 : Parte inferior do lado direito da tela 1 : Parte inferior do lado esquerdo da tela 2: Parte superior do lado esquerdo da tela 3 : Parte superior do lado direito da tela

16. Balance (Command: t)

Para ajustar o Balanço da som. Transmissão [k][t][ ][Set ID][ ][Data][Cr] Data Mín: 00H \~ Máx: 64H (Código hexadecimal)

Confirmation

[t][ ][Set ID][ ][OK][Data][x] Data Mín: 00H \~ Máx: 64H * Balanço : -50 \~ +50

17. ACC (Command: u)

Para ajustar a temperatura de cor da tela.

Transmission

[k][u][ ][Set ID][ ][Data][Cr] Data 0 : Normal (9300K) 1 : Frio 2:Morno(6500K) 3 : Utiliz. 4:3600K PC:0,2,3,4 Video:0,1,2

Confirmation

[u][ ][Set ID][ ][OK][Data][x] Data 0 : Normal (9300K) 1 : Frio 2:Morno(6500K) 3 : Utiliz. 4:3600K PC:0,2,3,4 Video:0,1,2 广力云智慧零售收银系统 

Transmission/reception protocol

18. PIP/PBP/POP SOURCE(Command: y) (PIP/PBP/POP SOURCE (Command: y))

Para selecionar a fonte da subtela. Transmissão [k][y][ ][Set ID][ ][Data][Cr]

Data 2:AV	6:RGB1
3:S-Video	7:RGB2
4:Component	8:DVI

Confirmação

[y][ ][Set ID][ ][OK][Data][x]

Data 2:AV	6:RGB1
3:S-Video	7:RGB2
4:Component	8:DVI

19. Auto Configure(Command: j u) (Auto Configure (Command: j u))

Para ajustar a posição da imagem e diminuir o tremor da imagem automaticamente. Funciona somente no modo RGB(PC). Transmissão

[j][u][ ][Set ID][ ][Data][Cr]

Data 1: Para definir Confirmação

[u][ ][Set ID][ ][OK][Data][x]

20. Key(Command: m c) (Key (Command: m c))

Para enviar códigos de tecla IR remota. Transmissão

[m][c][ ][Set ID][ ][Data][Cr]

Código de tecla de dados Confirmação

[c][ ][Set ID][ ][OK][Data][x]

21. Tiling Mode(Command: d d) (Tiling Mode (Command: d d))

▶ Altera um Modo lado a lado. Transmissão [d][d][ ][Set ID][ ][Data][x]

Dados:	Descrição
00	O modo lado a lado está desativado.
12	Modo 1 x 2 (coluna x linha)
13	Modo 1 x 3
14	Modo 1 x 4
...	...
44	Modo 4 x 4

* Os dados não podem ser definidos como 0X ou X0, exceto 00. Confirmação

[d][ ][00][ ][OK/NG][Data][x]

22. Tile H Position(Command: d e) (Tile H Position (Command: d e))

Para definir a posição horizontal. Transmissão

[d][e][ ][Set ID][ ][Data][x]

* O intervalo de dados é de 00 a 64(em Hex). Confirmação

[e][ ][Set ID][ ][OK/NG][Data][x]


Transmission/reception protocol

23. Tile V Position(Command : d f) (Posição vertical de lado a lado(Comando : d f)) Para definir a posição vertical. Transmissão [d][f][ ][Set ID][ ][Data][x] * O intervalo de dados é de 00 a 64(em Hex). Confirmação [f][ ][Set ID][ ][OK/NG][Data][x] 24. Tile H Size(Command : d g) (Tamanho horizontal de lado a lado(Comando : d g)) Para definir o tamanho horizontal. Transmissão [d][g][ ][Set ID][ ][Data][x] * O intervalo de dados é de 00 a 64(em Hex). Confirmação [g][ ][Set ID][ ][OK/NG][Data][x] 25. Tamanho vertical de lado a lado(Comando : d h) Para definir o tamanho vertical. Transmissão [d][h][ ][Set ID][ ][Data][x] * O intervalo de dados é de 00 a 64(em Hex). Confirmação [h][ ][Set ID][ ][OK/NG][Data][x] 26. Tile ID Set(Command : d i) (ID Set de lado a lado(Comando : d i)) Para atribuir a ID lado a lado para a função Lado a lado. Transmissão [d][i][ ][Set ID][ ][Data][x] * O intervalo de dados é de 00 a 00 x 10 modo lado a lado. Confirmação [i][ ][Set ID][ ][OK/NG][Data][x] 27. Elapsed time return(Command : d l) (Retorno de tempo decorrido d l)) Para ler o tempo decorrido. Transmissão [d][I][ ][Set ID][ ][Data][x] * Os dados estão sempre em FF (em Hex). Confirmação [1][Set ID][OK/NG][Data][x] *28. Light Sensor value Return(Command : d m) (Retorno do valor do sensor de iluminação(Comando : d m)) - opcional Para ler o valor do sensor de iluminação para ajustar o brilho do produto, dependendo do brilho do ambiente. Transmissão [d][m][ ][Set ID][ ][Data][x] * Os dados estão sempre em FF (em Hex). Confirmação [m][ ][Set ID][ ][OK/NG][Data][x] 

Transmission/reception protocol

*29. Temperature value Return(Command : d n) (Retorno do valor de temperatura (Comando : d n)) - opcional Para ler o valor de temperatura interna. Transmissão [d][n][ ][Set ID][ ][Data][x] * Os dados estão sempre em FF (em Hex). Confirmação [n][ ][Set ID][ ][OK/NG][Data][x] Os dados têm o tamanho de 1 byte no formato Hex ASCII. *30. Fan On/Off(Command : d o) (Ativado/Desativado(Comando : d o)) - opcional Para controlar definição de Ventilador Ativado/Desativado. Transmissão [d][o][ ][Set ID][ ][Data][x] Dado 0: Ventilador desativado 1: Ventilador ativado Confirmação [o][ ][Set ID][ ][OK/NG][Data][x] *31. Lamp fault Check(Command : d p) - opcional (Verificação de defeitos da lâmpada (Comando : d p)) Para verificar os defeitos da lâmpada. Transmissão [d][p][ ][Set ID][ ][Data][x] * Os dados estão sempre em FF (em Hex). Confirmação [p][ ][Set ID][ ][OK/NG][Data][x] *31. Lamp fault Check(Command : d p) - opcional (Verificação de defeitos da lâmpada (Comando : d p)) Para verificar os defeitos da lâmpada. Transmissão [d][p][ ][Set ID][ ][Data][x] * Os dados estão sempre em FF (em Hex). Confirmação [p][ ][Set ID][ ][OK/NG][Data][x] 0 : NG 1:OK *32. Video input fault return(Command : d q) - opcional (Retorno de falha na entrada de vídeo(Comando : d q)) Para verificar falha na entrada de vídeo Transmissão [d][q][ ][Set ID][ ][Data][x] * Os dados estão sempre em FF (em Hex). Confirmação [q][ ][Set ID][ ][OK/NG][Data][x] 0 : NG 1:OK

How to connect

▶ Conecte o controle remoto com fio à porta do controle remoto no aparelho.

Remote control IR code

▶ Forma da onda de saída pulso único, modulado com o sinal 37.917 KHz a 455KHz  Frequência da portadora FCAR = 1/Tc = fosc/12 Ciclo ativo = T1/Tc = 1/3 ▶ Configuração do quadro \- Primeiro quadro

Código de cabo conduto

Código personalizado baixo

Código personalizado alto

Código de dados

Código de dados

C0

C1

C2

C3

C4

C5

C6

C7

C0

C1

C2

C3

C4

C5

C6

C7

D0

D1

D2

D3

D4

D5

D6

D7

D0

D1

D2

D3

D4

D5

D6

D7

• Repetir quadro  ▶ Código de cabo condutor   ▶ Descrição de bits   ▶ Intervalo entre quadros: Tf \- A forma de onda é transmitida assim que a tecla é pressionada. 

Código (Hexa)	Função	Nota
02	VOL (▲)	Botão do controle remoto
03	VOL (▼)	Botão do controle remoto
40	▲	Botão do controle remoto
41	▼	Botão do controle remoto
06	►	Botão do controle remoto
07	◀	Botão do controle remoto
08	POWER ON/OFF	Botão do controle remoto (Liga/Desliga)
5B	EXIT	Botão do controle remoto
09	MUTE	Botão do controle remoto
4D	EZ VIDEO(PSM)	Botão do controle remoto
52	EZ AUDIO(SSM)	Botão do controle remoto
98	INPUT(Source)	Botão do controle remoto
5A	AV	Botão do controle remoto
D8	S-VIDEO	Botão do controle remoto
BF	COMPONENT	Botão do controle remoto
C6	DVI	Botão do controle remoto
0E	SLEEP	Botão do controle remoto
43	MENU	Botão do controle remoto
44	ENTER	Botão do controle remoto
60	PIP	Botão do controle remoto
61	POP	Botão do controle remoto
63	SWAP	Botão do controle remoto
79	ARC	Botão do controle remoto
76	ARC(4:3)	Botão do controle remoto
77	ARC(Full)	Botão do controle remoto
AF	ARC(ZOOM1)	Botão do controle remoto
54	AUTO	Botão do controle remoto

Met behulp van deze methode kunt u verschillende producten op één pc aansluiten. U kunt verschillende producten tegelijkertijd bedienen door ze op één pc aan te sluiten. 

Connecting cables

Sluit de RS-232C-kabel aan zoals in de afbeelding wordt weergegeven. * Het RS-232C-protocol wordt gebruikt voor de communicatie tussen pc en product. U kunt vanaf uw pc het product in-/uitschakelen, een ingang selecteren of het schermmenu aanpassen.  

Communication parameters

▶ Baudsnelheid: 9600bps (UART) ▶ Gegevenslengte: 8 bits ▶ Pariteitsbit: geen ▶ Stopbit: 1 bit ▶ Voortgangsbesturing: geen ▶ Communicatiecode: ASCII-code  Lijst met bedieningsfuncties

	OPDRACHT1 OPDRACHT2		DATA (hexa)
01. Power(Aan/uit)	k	a	00H - 01H
02. Input Select(Ingang selecteren)	k	b	02H - 08H
03. Aspect Ratio(Beeldverhouding)	k	c	01H - 06H
04. Screen Mute(Beeld dempen)	k	d	00H - 01H
05. Volume Mute(Volume dempen)	k	e	00H - 01H
06. Volume Control(Volume regelen)	k	f	00H - 64H
07. Contrast(Contrast)	k	g	00H - 64H
08. Brightness(Helderheid)	k	h	00H - 64H
09. Color(Kleur)	k	i	00H - 64H
10. Tint	k	j	00H - 64H
11. Sharpness(Scherpte)	k	k	00H - 64H
12. OSD Select(Schermmenu selecteren)	k	l	00H - 01H
13. Remote Lock On/Off(Vergr. afst.bed. aan/uit)	k	m	00H - 01H
14. PIP/PBP/POP On/Off(PIP/PBP/POP aan/uit)	k	n	00H - 03H
15. PIP Position(PIP-positie)	k	q	00H - 03H
16. Balance(Balans)	k	t	00H - 64H
17. ACC	k	u	00H - 04H
18. PIP/PBP/POP SOURCE(PIP/PBP/POP-bron)	k	y	00H - 08H
19. Auto Configure(Autoconfiguratie)	j	u	01H
20. Key(Sleutel)	m	c	Key Code
21. Tiling Mode(Mozaiekmodus)	d	d	00H - 0FH
22. Tile H Position(H positie mozaïek)	d	e	00H - 64H
23. Tile V Position(V positie mozaïek)	d	f	00H - 64H
24. Tile H Size(H grootte mozaïek)	d	g	00H - 64H
25. Tile V Size(V grootte mozaïek)	d	h	00H - 64H
26. Tile ID Set(Mozaïek-id instellen)	d	i	00H - 63H
27. Elapsed time return(Verstreken tijd retourneren)	d	l	FFH
*28. Light Sensor value return(Waarde lichtsensor retourneren)	d	m	FFH
*29. Temperatur value return(Temperatuurwaarde retourneren)	d	n	FFH
*30. Fan On/Off(Ventilator aan/uit)	d	o	00H - 01H
*31. Lamp fault check(Controleren op lampfout)	d	p	FFH
*32. Video input fault return(Pengembalian kerusakan masukan video)	d	q	FFH

*: optioneel 

Transmission/reception protocol

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

* [Command 1 (Opdracht 2)]: Eerste opdracht. (j,k,m,d) * [Command 2 (Opdracht 2)]: Tweede opdracht. * [Set ID]: U kunt de set-ID aanpassen om het identificatienummer van het gewenste product te kiezen in het menu Special (Speciaal). U kunt een waarde tussen 0 en 99 kiezen. Als u als set-ID '0' kiest, worden alle aangesloten tv's aangestuurd. De Set ID wordt in het menu als een decimale waarde (0 - 99) aangegeven en in het protocol voor uitzending/ontvangst als een hexadecimale waarde. * [DATA]: Hiermee worden opdrachtgegevens verzonden. Verzend FF-gegevens om de status van een opdracht te lezen. * [Cr]: Carriage Return (regelterugloop) ASCII-code '0x0D * [ ]: ASCII-code Ruimte (0x20)'

Positive acknowledgement

[Command2][ ][Set ID][ ][OK][Data][x]

* Het product verzendt een ACK (bevestiging) in deze indeling bij de ontvangst van normale gegevens. Op dit moment, met de gegevens in de leesmodus, worden de huidige statusgegevens weergegeven. Als de gegevens zich in de schrijfmodus bevinden, worden de gegevens van de pc geretourneerd.

Error acknowledgement

[Command2][ ][Set ID][ ][NG][Data][x]

* Het product verzendt een ACK (bevestiging) in deze indeling bij de ontvangst van abnormale gegevens ten gevolge van niet-uitvoerbare functies of communicatiefouten. Data 1: Ongeldige code 2: Niet-ondersteunde functie 3: Even geduld graag 

Transmission/reception protocol

01. Power (Command: a) (Power on (command: a))

▶ Hiermee zet u de set aan en uit. Uitzending [k][a][ ][Set ID][ ][Data][Cr] Data 0: Uitschakelen 1: Voeding aan Bevestiging [a][ ][Set ID][ ][OK][Data][x] Hier ziet u of de voeding is in- of uitgeschakeld. Uitzending [k][a][ ][Set ID][ ][FF][Cr] Data 0: Uitschakelen 1: Voeding aan Bevestiging [a][ ][Set ID][ ][OK][Data][x] * Het product verzendt een ACK (bevestiging) in deze indeling bij de ontvangst van normale gegevens. Op dit moment, met de gegevens in de leesmodus, worden de huidige statusgegevens weergegeven. Als de gegevens zich in de schrijfmodus bevinden, worden de gegevens van de pc geretourneerd.

02. Input Select (Command: b) (Main Picture Input) (Input select (command: b) (Main picture input))

Hiermee selecteert u de ingangsbron voor de set. U kunt ook een ingangsbron selecteren met behulp van de knop INPUT op de afstandsbediening. Uitzending [k][b][ ][Set ID][ ][Data][Cr]

Data 2:AV	6:RGB1
3:S-Video	7:RGB2
4:Component	8:DVI

Bevestiging [b][ ][Set ID][ ][OK][Data][x]

03. Aspect Ratio (Command: c) (Main picture format) (Aspect ratio (command: c) (Main window))

Hiermee past u de beeldgrootte aan. U kunt het schermformaat ook aanpassen met de knop ARC (Aspect Ratio Control, beeldverhouding) op de afstandsbediening of in het schermmenu.

Transmission

[k][c][ ][Set ID][ ][Data][Cr] Data 1:4:3 (Video) 2: Full (volledig) (PC, Video) 3 : Spectacle (weergave optimaliseren) (Video) 4:Zoom1 (zoomen1) (PC, Video) 5:Zoom2(zoomen2)(Video) 6:1:1(PC)

Acknowledgement

[c][ ][Set ID][ ][OK][Data][x]

04. Screen Mute (Command: d) (Screen mute (command: d))

Hiermee schakelt u de beelddemping in/uit.

Transmission

[k][d][ ][Set ID][ ][Data][Cr] Data 0 : Beeld dempen uit (Beeld aan) 1 : Beeld dempen aan (Beeld uit)

Acknowledgement

[d][ ][Set ID][ ][OK][Data][x] 

Transmission/Reception Protocol

05. Volume Mute (Command: e)

▶ Hiermee schakelt u Volume dempen in en uit.

Transmission

[k][e][ ][Set ID][ ][Data][Cr] Data 0 : Volume dempen aan (Volume uit) 1 : Volume dempen uit (Volume aan)

Acknowledgment

[e][ ][Set ID][ ][OK][Data][x] Data 0 : Volume dempen aan (Volume uit) 1 : Volume dempen uit (Volume aan)

06. Volume Control (Command: f)

▶ Met deze knop regelt u het volume.

Transmission

[k][f][ ][Set ID][ ][Data][Cr] Data Min : 00H \~ Max : 64H (Hexadecimale code)

Acknowledgment

[f][ ][Set ID][ ][OK][Data][x] Data Min : 00H \~ Max : 64H * Bestaande gegevenstoewijzing 0 : Step 0 : A : Step 10 : F : Step 15 10 : Step 16 : 64 : Step 100

07. Contrast (Command: g)

▶ Hiermee past u het contrast op het scherm aan. U kunt het contrast ook aanpassen vanuit het menu Picture (Beeld).

Transmission

[k][g][ ][Set ID][ ][Data][Cr] Data Min : 00H \~ Max : 64H • Zie 'Bestaande gegevenstoewijzing' hieronder.

Acknowledgment

[g][ ][Set ID][ ][OK][Data][x] * Bestaande gegevenstoewijzing 0 : Step 0 A : Step 10 F : Step 15 10 : Step 16 64 : Step 100

08. Brightness (Command: h)

Hiermee kunt u de helderheid van het scherm aanpassen. U kunt de helderheid ook aanpassen vanuit het menu Picture (Beeld).

Transmission

[k][h][ ][Set ID][ ][Data][Cr] Data Min : 00H \~ Max : 64H • Zie 'Bestaande gegevenstoewijzing' hieronder.

Acknowledgment

[h][ ][Set ID][ ][OK][Data][x] * Bestaande gegevenstoewijzing 0 : Step A : Step 10 F : Step 15 10 : Step 16 64 : Step 100 

Transmission/Reception Protocol

09. Color (Command: i) (Video only)

▶ Hiermee past u de kleuren van het beeld aan. U kunt de kleuren ook aanpassen vanuit het menu Picture (Beeld).

Transmission

[k][i][ ][Set ID][ ][Data][Cr] Data Min : 00H \~ Max : 64H (Hexadecimale code)

Acknowledgement

[i][ ][Set ID][ ][OK][Data][x] Data Min : 00H \~ Max : 64H

10. Tint (Command: j) (AV/S-Video: NTSC only)

▶ Hiermee past u de tint van het beeld aan. U kunt de tint ook aanpassen vanuit het menu Picture (Beeld).

Transmission

[k][j][ ][Set ID][ ][Data][Cr] Data rood: 00H \~ Groen: 64H (Hexadecimale code)

Acknowledgement

[j][ ][Set ID][ ][OK][Data][x] Data rood: 00H \~ Groen: 64H * Tint : -50 \~ +50

11. Sharpness (Command: k) (Video only)

Hiermee past u de scherpte van het beeld aan. U kunt de scherpte ook aanpassen vanuit het menu Picture (Beeld).

Transmission

[k][k][ ][Set ID][ ][Data][Cr] Data Min : 00H \~ Max : 64H (Hexadecimale code)

Acknowledgement

[k][ ][Set ID][ ][OK][Data][x] Data Min:00H\~Max:64H

12. OSD Select (Command: I)

▶ Hiermee schakelt u het schermmenu in of uit.

Transmission

[k][l][ ][Set ID][ ][Data][Cr] Data 0 : OSD Uit 1 : OSD Aan

Acknowledgement

[1][ ][Set ID][ ][OK][Data][x] Data 0: OSD Uit 1: OSD Aan

13. Remote Lock On/Off (Command: m)

▶ De afstandsbediening en de besturingselementen op het voorpaneel van de tv vergrendelen.

Transmission

[k][m][ ][Set ID][ ][Data][Cr] Data 0 : Vergrendeling afstandsbediening uit 1 : Vergrendeling afstandsbediening aan

Acknowledgement

[m][ ][Set ID][ ][OK][Data][x] Data 0: Vergrendeling afstandsbediening uit 1: Vergrendeling afstandsbediening aan Gebruik deze modus als u de afstandsbediening en de besturingselementen op het voorpaneel van de tv niet gebruikt. De vergrendeling van de afstandsbediening wordt opgeheven als de voeding wordt in- of uitgeschakeld. 

Transmission/Reception Protocol

14. PIP/PBP/POP On/Off (Command: n)

Hiermee zet u PIP/PBP/POP van de set aan en uit.

Transmission

[k][n][ ][Set ID][ ][Data][Cr] Data 0 : UIT 1:PIP 2 : PBP 3:POP

Acknowledgement

[n][ ][Set ID][ ][OK][Data][x] Data 0 : UIT 1 : PIP 2 : PBP 3:POP

15. PIP Position (Command: q)

▶ Hiermee past u de PIP-positie aan.

Transmission

[k][q][ ][Set ID][ ][Data][Cr] Data 0 : Rechtsonder in het scherm 1: Linksonder in het scherm 2:Linksboven in het scherm 3:Rechtsboven in het scherm

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x] Data 0 : Rechtsonder in het scherm 1 : Linksonder in het scherm 2:Linksboven in het scherm 3 : Rechtsboven in het scherm

16. Balance (Command: t)

▶ Hiermee past u de beeldbalans geluid. Uitzending [k][t][ ][Set ID][ ][Data][Cr] Data Min : 00H \~ Max : 64H (Hexadecimale code)

Acknowledgement

[t][ ][Set ID][ ][OK][Data][x] Data Min : 00H \~ Max : 64H * Balans : -50 \~ +50

17. ACC (Command: u)

▶ Hiermee past u de kleurtemperatuur van het beeld aan.

Transmission

[k][u][ ][Set ID][ ][Data][Cr] Data 0 : Normaal (9300K) 4 : 3600K 1: Koel PC: 0, 2, 3, 4 2:Warm(6500K) Video:0,1,2 3 : Aangepast

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x] Data 0 : Normaal (9300K) 4 : 3600K 1: Koel PC: 0, 2, 3, 4 2:Warm(6500K) Video:0,1,2 3 : Aangepast 

Transmission/Reception Protocol

18. PIP/PBP/POP SOURCE (Command: y)

▶ Hiermee kiest u de bron voor het subvenster. Uitzending [k][y][ ][Set ID][ ][Data][Cr]

Data 2:AV	6:RGB1
3:S-Video	7:RGB2
4:Component	8:DVI

Bevestiging [y][ ][Set ID][ ][OK][Data][x]

Data 2:AV	6:RGB1
3:S-Video	7:RGB2
4:Component	8:DVI

19. Auto Configure (Command: j u)

Hiermee past u de beeldpositie aan en minimaliseert u de beeldtrillingen automatisch. Alleen in de modus RGB(PC). Uitzending [j][u][ ][Set ID][ ][Data][Cr] Data 1 : Instellen Bevestiging [u][ ][Set ID][ ][OK][Data][x]

20. Key (Command: m c)

Hiermee verzendt u de sleutelcode voor de IR-afstandsbediening. Uitzending [m][c][ ][Set ID][ ][Data][Cr] Datacode Bevestiging [c][ ][Set ID][ ][OK][Data][x]

21. Tiling Mode (Command: d d)

▶ Hiermee wijzigt u een mozaïekmodus. Uitzending [d][d][ ][Set ID][ ][Data][x]

Data	Beschrijving
00	Mozaïekmodus is uitgeschakeld.
12	Modus 1 x 2 (kolom x rij)
13	Modus 1 x 3
14	Modus 1 x 4
...	...
44	Modus 4 x 4

* De gegevens kunnen niet worden ingesteld op 0X of X0, behalve 00. Bevestiging [d][ ][00][ ][OK/NG][Data][x]

22. Tile H Position (Command: d e)

▶ Hiermee stelt u de horizontale positie in. Uitzending [d][e][ ][Set ID][ ][Data][x] * Het gegevensbereik ligt tussen 00 en 64 (hexadecimaal). Bevestiging [e][ ][Set ID][ ][OK/NG][Data][x] 

Transmission/Reception Protocol

23. Tile V Position (Command: d f)

▶ Hiermee stelt u de verticale positie in. Uitzending [d][f][ ][Set ID][ ][Data][x] * Het gegevensbereik ligt tussen 00 en 64 (hexadecimaal). Bevestiging [f][ ][Set ID][ ][OK/NG][Data][x]

24. Tile H Size (Command: d g)

▶ Hiermee stelt u de horizontale grootte in. Uitzending [d][g][ ][Set ID][ ][Data][x] * Het gegevensbereik ligt tussen 00 en 64 (hexadecimaal). Bevestiging [g][ ][Set ID][ ][OK/NG][Data][x]

25. Tile V Size (Command: d h)

▶ Hiermee stelt u de verticale grootte in. Uitzending [d][h][ ][Set ID][ ][Data][x] * Het gegevensbereik ligt tussen 00 en 64 (hexadecimaal). Bevestiging [h][ ][Set ID][ ][OK/NG][Data][x]

26. Tile ID Set (Command: d i)

Hiermee wijst u de mozaïek-id toe voor de functie Mozaïek. Uitzending [d][i][ ][Set ID][ ][Data][x] * Het gegevensbereik ligt tussen 00 en mozaïekmodus 00 x 10. Bevestiging [i][ ][Set ID][ ][OK/NG][Data][x]

27. Elapsed Time Return (Command: d l)

▶ Hiermee leest u de verstreken tijd. Uitzending [d][I][ ][Set ID][ ][Data][x] * De gegevenswaarde is altijd FF (hexadecimaal). Bevestiging [1][ ][Set ID][ ][OK/NG][Data][x]

*28. Light Sensor Value Return (Command: d m) - optional

Hiermee leest u de waarde van de lichtsensor om de helderheid van het product aan te passen afhankelijk van de helderheid in de omgeving. Uitzending [d][m][ ][Set ID][ ][Data][x] * De gegevenswaarde is altijd FF (hexadecimaal). Bevestiging [m][ ][Set ID][ ][OK/NG][Data][x] 

Transmission/Reception Protocol

*29. Temperature Value Return

(Command : d n) (Temperatuurwaarde retourneren (opdracht: d n)) - optioneel Hiermee leest u de temperatuur aan de binnenkant.

Transmission

[d][n][ ][Set ID][ ][Data][x] * De gegevenswaarde is altijd FF (hexadecimaal).

Acknowledgment

[n][ ][Set ID][ ][OK/NG][Data][x] Gegevens zijn 1 byte lang in hexadecimale ASCII-indeling.

*30. Fan On/Off (Command: d o)

(Ventilator aan/uit (opdracht: d o)) - optioneel ▶ Hiermee schakelt u de ventilator voor de set in of uit.

Transmission

[d][o][ ][Set ID][ ][Data][x] Data 0: Ventilator uit 1: Ventilator aan

Confirmation

[o][ ][Set ID][ ][OK/NG][Data][x]

*31. Lamp fault Check (Command: d p) (Check for lamp fault (command: d p)) - optional

▶ Hiermee controleert u op een lampfout.

Transmission

[d][p][ ][Set ID][ ][Data][x] * De gegevenswaarde is altijd FF (hexadecimaal).

Confirmation

[p][ ][Set ID][ ][OK/NG][Data][x]

*31. Lamp fault Check (Command: d p) (Check for lamp fault (command: d p)) - optional

▶ Hiermee controleert u op een lampfout.

Transmission

[d][p][ ][Set ID][ ][Data][x] * De gegevenswaarde is altijd FF (hexadecimaal).

Confirmation

[p][ ][Set ID][ ][OK/NG][Data][x] 0:NG 1:OK

*32. Video input fault return (Command: d q) (Return of video input fault (command: d q)) - optional

▶ Untuk memeriksa kesalahan masukan video.

Transmission

[d][q][ ][Set ID][ ][Data][x] * De gegevenswaarde is altijd FF (hexadecimaal).

Confirmation

[q][ ][Set ID][ ][OK/NG][Data][x] 0:NG 1:OK

Connection

▶ Sluit de afstandsbediening met draad aan op de daarvoor bestemde poort van het product.

IR code remote control

▶ Output waveform

Enkelvoudige impuls, gemoduleerd met 37,917 KHz-signaal bij 455 KHz  Draagfrequentie FCAR = 1/Tc = fosc/12 Pulsverhouding = T1/Tc = 1/3

▶ Frame configuration

- 1^e frame  • Frame herhalen  ▶ Voorloopcode  ▶ Code herhalen  ▶ Omschrijving bit   ▶ interval van frame: Tf - Zolang een toets wordt ingedrukt, wordt de golfvorm verzonden. 

Code(Hexa)	Functie	Opmerking
02	VOL (▲)	Knop afstandsbediening
03	VOL (▼)	Knop afstandsbediening
40	▲	Knop afstandsbediening
41	▼	Knop afstandsbediening
06	▶	Knop afstandsbediening
07	◀	Knop afstandsbediening
08	AAN/UIT	Knop afstandsbediening (aan/uit)
5B	EXIT	Knop afstandsbediening
09	MUTE	Knop afstandsbediening
4D	EZ VIDEO(PSM)	Knop afstandsbediening
52	EZ AUDIO(SSM)	Knop afstandsbediening
98	INPUT(Source)	Knop afstandsbediening
5A	AV	Knop afstandsbediening
D8	S-VIDEO	Knop afstandsbediening
BF	COMPONENT	Knop afstandsbediening
C6	DVI	Knop afstandsbediening
0E	SLEEP	Knop afstandsbediening
43	MENU	Knop afstandsbediening
44	ENTER	Knop afstandsbediening
60	PIP	Knop afstandsbediening
61	POP	Knop afstandsbediening
63	SWAP	Knop afstandsbediening
79	ARC	Knop afstandsbediening
76	ARC(4:3)	Knop afstandsbediening
77	ARC(Full)	Knop afstandsbediening
AF	ARC(ZOOM1)	Knop afstandsbediening
54	AUTO	Knop afstandsbediening

Ezzel a módszerrel egyszerre több készüléket csatlakoztathat egyetlen számítógéphez. Egyetlen számítógépről egyszerre kezelheti az összes csatlakoztatott készüléket. 

Cable connection

Csatlakoztassa az RS-232C kábelt az ábrán látható módon. * A számítógép az RS-232C protokoll segítségével vezérli a készülékeket. Így a számítógép segítségével ki- és bekapcsolhatja a készüléket, kiválaszthatja a bemeneti jelet vagy megadhatja a beállításokat a képernyőmenüben (OSD).  

Communication parameters

Adatsebesség: 9600 bps (UART) ▶ Adathossz: 8 bit Paritásbit: nincs ▶ Stopbit: 1 bit ▶ Adatáram-vezérlés: nincs ▶ Kommunikációs kód: ASCII-kód  Részletes parancslista

	1.PARANCS	2.PARANCS	ADAT (hexodecimális)
01. Power(Tápellátás)	k	a	OOH - 01H
02. Input Select(Bemenetválasztás)	k	b	02H - 08H
03. Aspect Ratio(Méretarány)	k	c	01H - 06H
04. Screen Mute(Kép kikapcsolása)	k	d	OOH - 01H
05. Volume Mute(Hang némítása)	k	e	OOH - 01H
06. Volume Control(Hangerőszabályzás)	k	f	OOH - 64H
07. Contrast(Kontraszt)	k	g	OOH - 64H
08. Brightness(Fényerő)	k	h	OOH - 64H
09. Color(Szín)	k	i	OOH - 64H
10. Tint(Színárnyalat)	k	j	OOH - 64H
11. Sharpness(Élesség)	k	k	OOH - 64H
12. OSD Select(OSD választása)	k	l	OOH - 01H
13. Remote Lock On/Off(Távirányító-zárolás be/ki)	k	m	OOH - 01H
14. PIP/PBP/POP On/Off(PIP/PBP/POP be/ki)	k	n	OOH - 03H
15. PIP Position(PIP helyzet)	k	q	OOH - 03H
16. Balance(Balansz)	k	t	OOH - 64H
17. ACC	k	u	OOH - 04H
18. PIP/PBP/POP SOURCE(PIP/PBP/POP forrása)	k	y	OOH - 08H
19. Auto Configure(Automatikus konfigurálás)	j	u	01H
20. Key(Gomb)	m	c	Gomb kódja
21. Tiling Mode(Mozaikrendezési mód)	d	d	OOH - 0FH
22. Tile H Position(Mozaik vízszintes helyzete)	d	e	OOH - 64H
23. Tile V Position(Mozaik függőleges helyzete)	d	f	OOH - 64H
24. Tile H Size(Mozaik vízszintes mérete)	d	g	OOH - 64H
25. Tile V Size(Mozaik függőleges mérete)	d	h	OOH - 64H
26. Tile ID Set(Mozaikazonosító beállítása)	d	i	OOH - 63H
27. Elapsed time return(Elteit idő lekérdezése)	d	l	FFH
* 28. Light Sensor value return(Fényérzékelő értékének lekérdezése)	d	m	FFH
* 29. Temperatur value return(Hómérséklet értékének lekérdezése)	d	n	FFH
* 30. Fan On/Off(Ventilátor be/ki)	d	o	OOH - 01H
* 31. Lamp fault check(Jelzőfényhiba ellenőrzése)	d	p	FFH
* 32. Video input fault return(Videobemenet-hiba lekérése)	d	q	FFH

* : külön rendelhetó 

Data transmission protocol

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

* [1. parancs]: Elsö parancs. (j, k, m, d) * [2. parancs]: Második parancs. * [Készülékazonosító]: A készülékazonosítót a Special (Speciális) menüben állíthatja be a kívánt azonosító kiválasztásához. A beállítási tartomány 0–99. Ha a készülékazonosító értéke „0”, minden csatlakoztatott TV-készüléket vezérel. A készülékazonosító decimális (0–99) alakban jelenik meg a menüben, és hexadecimális (0x0–0x64) alakban az adatátviteli protokollban. * [ADAT]: A parancsadat továbbítása. A parancsállapot olvasásához az „FF” adatot kell küldeni. * [KV]: Kocsi vissza „0x0D” ASCII-kód * [ ]: Szóköz, „0x20” ASCII-kód

OK acknowledgment

[Command2][ ][Set ID][ ][OK][Data][x]

* A készülék ebben a formátumban küldi a visszaigazolást (ACK), ha helyes adatokat kapott. Adatolvasási mód esetén a jelenlegi állapotadatokat tartalmazza. Adatírási mód esetén a számítógépből származó adatokat küldi vissza.

Error acknowledgment

[Command2][ ][Set ID][ ][NG][Data][x]

* A készülék ebben a formátumban küld visszaigazolást (ACK), ha hibás adatokat kap nem használható funkciókhoz, vagy kommunikációs hiba történt. Adat 1: Illegális kód 2: Nem használható funkció 3: További várakozás szükséges 

Data transmission protocol

01. Power (Command : a) (Bekapcsolás (Parancs ▶ A készülék be- és kikapcsolását vezérli. Küldés [k][a][ ][Set ID][ ][Data][Cr] Adat 0: Kikapcsolás 1: Bekapcsolás Visszaigazolás [a][ ][Set ID][ ][OK][Data][x] ▶ A be- vagy kikapcsolt állapot megjelenítése. Küldés [k][a][ ][Set ID][ ][FF][Cr] Adat 0: Kikapcsolás 1: Bekapcsolás Visszaigazolás [a][ ][Set ID][ ][OK][Data][x] * A készülék ebben a formátumban küldi a visszaigazolást (ACK), ha helyes adatokat kapott. Adatolvasási mód esetén a jelenlegi állapotadatokat tartalmazza. Adatírási mód esetén a számítógépből származó adatokat küldi vissza. 02. Input Select(Command : b) (Main Picture Input) (Bemenetválasztás (Parancs: b) (Fókép bemenete)) ▶ A készülék bemeneti jelforrásának kiválasztása. A távirányító INPUT gombjával is kiválaszthatja a bemeneti jelforrást. Küldés [k][b][ ][Set ID][ ][Data][Cr] Adat 2:AV 6:RGB1 3 : S-Video 7:RGB2 4: Component 8 : DVI Visszaigazolás [b][ ][Set ID][ ][OK][Data][x] 03. Aspect Ratio(Command : c) (Manin picure format) (Méretarány (Parancs: c) (Fökép formátuma)) ▶ A képformátum beállítása. A Screen (Képernyő) menüben vagy a távirányító ARC (Méretarány-vezérlés) gombjával is beállíthatja a képformátumot. Küldés [k][c][ ][Set ID][ ][Data][Cr] Adat 1:4:3 (Video) 2: Full (Teljes) (PC, Video) 3 : Spectacle (Látvány) (Video) 4:Zoom1(Nagyítás1)(PC,Video) 5:Zoom2(Nagyítás2)(Video) 6:1:1(PC) Visszaigazolás [c][ ][Set ID][ ][OK][Data][x] 04. Screen Mute(Command : d) (Kép kikapcsolása (Parancs: d)) ▶ A kép be-/kikapcsolásának választása. Küldés [k][d][ ][Set ID][ ][Data][Cr] Adat 0 : Képkikapcsolás bekapcsolva) inaktív (kép 1: Képkikapcsolás kikapcsolva) aktív (kép Visszaigazolás [d][ ][Set ID][ ][OK][Data][x] 

Data transmission protocol

05. Volume Mute(Command : e) (Hang némítása (Parancs: e)) ▶ A hangnémítás be- és kikapcsolását vezérli.

Transmission

[k][e][ ][Set ID][ ][Data][Cr] Adat 0: Hang némítása aktiv (hang kikapcsolva) 1: Hang némítása inaktív (hang bekapcsolva)

Acknowledgment

[e][ ][Set ID][ ][OK][Data][x] Adat 0: Hang némítása aktiv (hang kikapcsolva) 1: Hang némítása inaktív (hang bekapcsolva) 06. Hangerő-szabályozás (Parancs: f) ▶ A hangerő beállítása.

Transmission

[k][f][ ][Set ID][ ][Data][Cr] Adat Min.: 00H – Max: 64H (Hexadecimális kód)

Acknowledgment

[f][ ][Set ID][ ][OK][Data][x] Adat Min.: 00H - Max: 64H * Valós adatok leképezése 0:0. lépés A: 10. lépés F : 15. lépés 10 : 16. lépés 64 : 100. lépés 07. Contrast(Command : g) (Kontraszt (Parancs: g)) ▶ A képernyőkontraszt beállítása. A kontrasztot a Picture (Kép) menüben is beállíthatja.

Transmission

[k][g][ ][Set ID][ ][Data][Cr] Adat Min.: 00H - Max: 64H \- Šlásd az alábbi „Valós adatok leképezése” pontot.

Confirmation

[g][ ][Set ID][ ][OK][Data][x] * Valós adatok leképezése 0 : 0. lépés A: 10. lépés F : 15. lépés 10 : 16. lépés 64 : 100. lépés 08. Brightness(Command : h) (Fényerő (Parancs: h)) ▶ A képernyő fényerejének beállítása. A fényerőt a Picture (Kép) menüben is beállíthatja.

Sending

[k][h][ ][Set ID][ ][Data][Cr] Adat Min.: 00H - Max: 64H \- Šlásd az alábbi „Valós adatok leképezése” pontot.

Confirmation

[h][ ][Set ID][ ][OK][Data][x] * Valós adatok leképezése 0 : 0. lépés A: 10. lépés F : 15. lépés 10 : 16. lépés 64 : 100. lépés 

Data transmission protocol

09. Color(Command : i) (Video only) (Szín (Parancs: i) (csak Video)) ▶ A képernyő színbeállítása. A színt a Picture (Kép) menüben is beállíthatja. Küldés [k][i][ ][Set ID][ ][Data][Cr] Adat Min.: 00H – Max: 64H (Hexadecimális kód) Visszaigazolás [i][ ][Set ID][ ][OK][Data][x] Adat Min.: 00H - Max: 64H 10. Tint(Command : j) (Színárnyalat (Parancs: j)(AV/S-Video: ccsak NTSC) ▶ A képernyő színárnyalatának beállítása. A színárnyalatot a Picture (Kép) menüben is beállíthatja. Küldés [k][j][ ][Set ID][ ][Data][Cr] Adat: Vörös: 00H – Zöld: 64H (Hexadecimális kód) Visszaigazolás [i][ ][Set ID][ ][OK][Data][x] Adat: Vörös: 00H – Zöld: 64H * Színárnyalat: -50 - +50 11. Sharpness(Command : k) (Video only) (Élesség (Parancs: k) (csak Video)) ▶ A képernyő élességének beállítása. Az élesseget a Picture (Kép) menüben is beállíthatja. Küldés [k][k][ ][Set ID][ ][Data][Cr] Adat Min.: 00H – Max: 64H (Hexadecimális kód) Visszaigazolás [k][ ][Set ID][ ][OK][Data][x] Adat Min.: 00H - Max: 64H 12. OSD Select(Command : I) (OSD választása (Parancs: I)) ▶ A készülék képernyőmenűjének (OSD) be- és kikapcsolását vezérli. Küldés [k][l][ ][Set ID][ ][Data][Cr] Adat 0: OSD kikapcsolva 1: OSD bekapcsolva Visszaigazolás [1][ ][Set ID][ ][OK][Data][x] Adat 0: OSD kikapcsolva 1: OSD bekapcsolva 13. Remote Lock On/Off(Command : m) (A távirányító és a gombok lezárása (Parancs: m)) ▶ A készülék távirányítóján és előlapján található kezelőszervek zárolása. Transmission [k][m][ ][Set ID][ ][Data][Cr] Data 0 : Remote Lock Off 1 : Remote Lock On Acknowledgement [m][ ][Set ID][ ][OK][Data][x] Data 0: Remote Lock Off 1: Remote Lock On Ha nem használja a készülék távirányítóját és az előlapján található kezelőszerveket, állítsa be ezt a módot A tápellátós be- és kikapcsolása esetén a távvezérlés zárolása kikapcsol. 

Data transmission protocol

14. PIP/PBP/POP On/Off(Command : n) (PIP/PBP/POP be- vagy kikapcsolása (Parancs: n)) ▶ A PIP/PBP/POP be- és kikapcsolását vezérli.

Sending

[k][n][ ][Set ID][ ][Data][Cr] Adat 0 : Kikapcsolva 1:PIP 2 : PBP 3:POP

Confirmation

[n][ ][Set ID][ ][OK][Data][x] Adat 0: Kikapcsolva 1 : PIP 2 : PBP 3:POP 15. PIP Position(Command : q) (PIP helyzet (Parancs: q)) ▶ A PIP helyzetének beállítása.

Sending

[k][q][ ][Set ID][ ][Data][Cr] Adat 0 : A képernyő jobb alsó sarkában 1 : A képernyő bal alsó sarkában 2 : A képernyő bal felső sarkában 3 : A képernyő jobb felső sarkában

Confirmation

[q][ ][Set ID][ ][OK][Data][x] Adat 0 : A képernyő jobb alsó sarkában 1: A képernyő bal alsó sarkában 2 : A képernyő bal felső sarkában 3 : A képernyő jobb felső sarkában 16. Balance(Command : t) (Balansz (Parancs: t)) ▶ A képernyő balanszbeállításának meghatározása. Küldés [k][t][ ][Set ID][ ][Data][Cr] Adat Min.: 00H - Max: 64H (Hexadecimális kód) Visszaigazolás [t][ ][Set ID][ ][OK][Data][x] Adat Min.: 00H - Max: 64H * Balansz : -50 \~ +50 17. ACC(Command : u) (ACC (Parancs: u)) ▶ A képernyő színhömérsékletének beállítása. Küldés [k][u][ ][Set ID][ ][Data][Cr] Adat 0: Normál (9300K) 4: 3600K 1: Hideg PC: 0, 2, 3, 4 2:Meleg(6500K) Video:0,1,2 3 : Egyéni

Confirmation

[u][ ][Set ID][ ][OK][Data][x] Adat 0: Normál (9300K) 4: 3600K 1: Hideg PC: 0, 2, 3, 4 2:Meleg(6500K) Video:0,1,2 3 : Egyéni 

Data transmission protocol

18. PIP/PBP/POP SOURCE(Command : y) (PIP/PBP/POP forrása (Parancs: y)) ▶ A kis képernyő jelforrásának kiválasztása. Küldés

[k][y][ ][Set ID][ ][Data][Cr]
Adat 2:AV	6:RC
3:S-Video	7:RC
4:Component	8:DV

Visszaigazolás

[y][ ][Set ID][ ][OK][Data][x]
Adat 2:AV	6:RG
3:S-Video	7:RG
4:Component	8:DV

19. Auto Configure(Command: j u) (Automatikus konfigurálás (Parancs: j u)) A kép helyzetének beállítása és a kép remegésének csökkentése automatikusan. Kizárólag RGB (PC) üzemmódban használható. Küldés [j][u][ ][Set ID][ ][Data][Cr] Adat 1: Beállítás Visszaigazolás [u][ ][Set ID][ ][OK][Data][x] 20. Key(Command : m c) (Gomb (Parancs: m c)) ▶ Infravörös távirányító gombkódjának küldése. Küldés [m][c][ ][Set ID][ ][Data][Cr] Gombkódok Visszaigazolás [c][ ][Set ID][ ][OK][Data][x] 21. Tiling Mode(Command : d d) (Mozaikrendezési mód (Parancs: d d)) ▶ Mozaikrendezési mód módosítása. Küldés [d][d][ ][Set ID][ ][Data][x]

Adat	Leírás
00	Mozakrendezési mód kikapcsolva.
12	1 x 2 mód (oszlop x sor)
13	1 x 3 mód
14	1 x 4 mód
...	...
44	4 x 4 mód

* Az adat nem állítható be 0X vagy X0 értékre a 00 kivételével. Visszaigazolás [d][ ][00][ ][OK/NG][Data][x] 22. Tile H Position(Command : d e) (Mozak vizszintes helyzete (Parancs: d e)) ▶ A vízszintes helyzet beállítása. Küldés [d][e][ ][Set ID][ ][Data][x] * Az adatérték 00 és 64 (hexadecimális) közötti lehet. Visszaigazolás [e][ ][Set ID][ ][OK/NG][Data][x] 

Data transmission protocol

23. Tile V Position(Command : d f) (Mozak függöleges helyzete (Parancs: d f)) ▶ A függöleges helyzet beállítása. Küldés [d][f][ ][Set ID][ ][Data][x] * Az adatérték 00 és 64 (hexadecimális) közötti lehet. Visszaigazolás [f][ ][Set ID][ ][OK/NG][Data][x] 24. Tile H Size(Command : d g) (Mozak vízszintes mérete (Parancs: d g)) ▶ A vízszintes méret beállítása. Küldés [d][g][ ][Set ID][ ][Data][x] * Az adatérték 00 és 64 (hexadecimális) közötti lehet. Visszaigazolás [g][ ][Set ID][ ][OK/NG][Data][x] 25. Tile V Size(Command : d h) (Mozak függöleges mérete (Parancs: d h)) ▶ A függőleges méret beállítása. Küldés [d][h][ ][Set ID][ ][Data][x] * Az adatérték 00 és 64 (hexadecimális) közötti lehet. Visszaigazolás [h][ ][Set ID][ ][OK/NG][Data][x] 26. Tile ID Set(Command : d i) (Mozakazonosító beállítása (Parancs: d i)) ▶ Mozaikazonosító hozzárendelése a mozaikrendezési funkcióhoz. Küldés [d][i][ ][Set ID][ ][Data][x] * Az adatérték 00 és a 00 x 10 mozaikrendezési mód közötti lehet. Visszaigazolás [i][ ][Set ID][ ][OK/NG][Data][x] 27. Elapsed time return(Command : d l) (Éltelt idő lekérdezése (Parancs: d l)) ▶ Az eltelt idő kiolvasása. Küldés [d][l][ ][Set ID][ ][Data][x] * Az adat értéke mindig FF (hexadecimális). Visszaigazolás [1][ ][Set ID][ ][OK/NG][Data][x] *28. Light Sensor value Return(Command : d m) (Fényérzékelő értékének lekérdezése (Parancs: d m)) - külön rendelhető ▶ A fényérzékelő értékének kiolvasása a készüléken a környezeti fényviszonyoktól függő fényerősség beállításához. Küldés [d][m][ ][Set ID][ ][Data][x] * Az adat értéke mindig FF (hexadecimális). Visszaigazolás [m][ ][Set ID][ ][OK/NG][Data][x] 

Data transmission protocol

*29. Temperature value Return(Command : d n) (Hőmérséklet értékének lekérdezése (Parancs: d n)) - külön rendelhető ▶ A belső hömérséklet értékének kiolvasása.

Sending

[d][n][ ][Set ID][ ][Data][x] * Az adat értéke mindig FF (hexadecimális).

Confirmation

[n][ ][Set ID][ ][OK/NG][Data][x] Az adat hossza 1 bájt, hexadecimális ASCII-formátumban. *30. Fan On/Off(Command : d o) (Ventilátor be/ki (Parancs: d o)) - külön rendelhetó ▶ A készülék ventilátorának be- és kikapcsolását vezérli.

Send

[d][o][ ][Set ID][ ][Data][x] Adat 0: Ventilátor ki 1: Ventilátor be

Confirmation

[o][ ][Set ID][ ][OK/NG][Data][x] *31. Lamp fault Check(Command : d p) (Jelzőfényhiba ellenőrzése (Parancs: d p)) - külön rendelhető ▶ A jelzőfényhibák ellenőrzése.

Send

[d][p][ ][Set ID][ ][Data][x] * Az adat értéke mindig FF (hexadecimális).

Confirmation

[p][ ][Set ID][ ][OK/NG][Data][x] *31. Lamp fault Check(Command : d p) (Jelzőfényhiba ellenőrzése (Parancs: d p)) - külön rendelhető ▶ A jelzőfényhibák ellenőrzése.

Send

[d][p][ ][Set ID][ ][Data][x] * Az adat értéke mindig FF (hexadecimális).

Confirmation

[p][ ][Set ID][ ][OK/NG][Data][x] 0:NG 1:OK *32. Video input fault return(Command : d q) (Jelzőfényhiba ellenőrzése (Parancs: d q)) - külön rendelhető ▶ A videobemenet-hibák ellenőrzése.

Send

[d][q][ ][Set ID][ ][Data][x] * Az adat értéke mindig FF (hexadecimális).

Confirmation

[q][ ][Set ID][ ][OK/NG][Data][x] 0:NG 1:OK

Connection

▶ A vezetékes távirányítót a készülék Remote Control (Távirányító) aljzatához kell csatlakoztatni.

Remote control infrared code

▶ Kimeneti hullámforma egyimpulzusú, 37.917 kHz-es jellel modulált 455 kHz-es jel  Vivöfrekvencia FCAR = 1 / Tc = f o s c / 1 2 Idóarány = T1 / Tc = 1 / 3 ▶ A keret felépítése •1. keret  - Ismétlökeret  ▶ Bevezető kód  ▶ Ismétlőkód  ▶ Bitek felépítése   ▶ Keret idötartama: Tf \- A távirányító a gomb nyomva tartása alatt folyamatosan sugározza a hullámot. 

Kód (hex.)	Funkció	Megjegyzés
02	VOL (▲)	Távirányító gombja
03	VOL (▼)	Távirányító gombja
40	▲	Távirányító gombja
41	▼	Távirányító gombja
06	►	Távirányító gombja
07	◀	Távirányító gombja
08	TÁPELLÁTÁS BE- ÉS KIKAPCSOLÁSA	Távirányító gombja (be/ki)
5B	EXIT	Távirányító gombja
09	MUTE	Távirányító gombja
4D	EZ VIDEO(PSM)	Távirányító gombja
52	EZ AUDIO(SSM)	Távirányító gombja
98	INPUT(Source)	Távirányító gombja
5A	AV	Távirányító gombja
D8	S-VIDEO	Távirányító gombja
BF	COMPONENT	Távirányító gombja
C6	DVI	Távirányító gombja
OE	SLEEP (ALVÓ ÜZEMMÓD)	Távirányító gombja
43	MENU (MENÜ)	Távirányító gombja
44	ENTER	Távirányító gombja
60	PIP	Távirányító gombja
61	POP	Távirányító gombja
63	SWAP (CSERE)	Távirányító gombja
79	ARC (MÉRETARÁNY)	Távirányító gombja
76	ARC(4:3)	Távirányító gombja
77	ARC(Full)	Távirányító gombja
AF	ARC(ZOOM1)	Távirányító gombja
54	AUTO	Távirányító gombja

_ | _ \- 1 _ | _ \- 1