KA CEH 4 - Heating KALORIK - Free user manual and instructions

Product Type	Fan Heater
Brand	Kalorik
Model	KA CEH 4
Heating Modes	Fan only, Low heat, High heat, Auto thermostat
Control Type	Manual control panel and remote control
Remote Control	Yes, operates all functions; requires 2 AAA batteries (1.5 V)
Oscillation	Yes, left-right oscillation, toggle on/off
Timer	1 to 8 hours, adjustable in 1-hour increments
Thermostat	Adjustable set temperature; heater cycles on/off to maintain set temp
Display	LCD screen showing current room temperature or remaining timer
Safety Features	Tip-over switch (auto shut-off), overheat protection (auto shut-off)
Batteries	2 x AAA 1.5 V for remote control
Cleaning	Wipe housing with damp cloth; vacuum grilles gently
Usage	Indoor only; place on stable, level surface; keep 50 cm from walls, 1 m from combustibles
Power Supply	Mains voltage as per rating plate (typical 220-240 V ~ 50/60 Hz)
Wattage	Not specified in manual (typical for fan heater: 2000 W)

Frequently Asked Questions - KA CEH 4 KALORIK

How do I set the timer on the Kalorik KA CEH 4 heater?

Press the Timer button repeatedly to increase the operating time from 1 to 8 hours in 1-hour increments. The display shows remaining time. After 8 hours, pressing again cancels the timer and sets the heater to continuous operation.

How does the remote control work?

Insert two AAA batteries (1.5 V) in the remote, observing polarity. The remote can turn the heater on/off, adjust temperature, set timer, change heat mode, and toggle oscillation. Ensure no obstacles between remote and heater.

What should I do if the heater tips over?

The heater has a tip-over safety switch that automatically shuts it off. If it falls, unplug it, place it upright on a stable surface, and then turn it on again via the main power switch and ON/OFF button.

How do I clean the Kalorik KA CEH 4 heater?

Always unplug and let the heater cool completely. Wipe the housing with a slightly damp, lint-free cloth. Clean the grilles carefully with a vacuum cleaner; do not use abrasive pads or immerse in water.

What does AUTO mode do?

In Auto mode, the heater maintains the set temperature you choose (using + and - buttons). When room temperature exceeds the set temp by 3°C, the heater turns off. When it drops 1°C below set temp, it turns back on.

Why does the heater cycle on and off during use?

This is normal operation in Auto mode or when the thermostat is active. The heater cycles to maintain the desired temperature, ensuring energy efficiency and consistent comfort.

What safety features does the heater have?

The heater includes a tip-over switch (shuts off if tilted) and overheat protection (shuts off if internal temperature exceeds safe limit, e.g., from blocked grilles). After cooling, it can be restarted.

Can I use this heater in a bathroom?

No. The manual warns: Do not operate near baths, showers, washbasins, swimming pools, or any water container. The heater is for indoor, dry locations only.

What batteries does the remote control need?

The remote requires two AAA 1.5V batteries. Do not mix old and new batteries or different types. Remove batteries if not using the remote for a long time.

Why does the heater emit a smell when first used?

A slight smell may occur during first use. It is normal and will disappear quickly. Ensure good ventilation by opening a window or door until the smell fades.

USER MANUAL KA CEH 4 KALORIK

2 KA CEH 4 - 050425

GB

1. Tilt switch
2. Main power switch
3. Air outlet
4. LCD display
5. Pilot light

Control panel

1. Oscillation button

2. Heat mode button

3. Timer button

4. Temperature adjusting buttons

5. ON/OFF switch

Remote control

1. Temperature adjusting button
2. ON/OFF switch
3. Timer button
4. Heat mode button
5. Oscillation button

SP

☐ Please read these instructions carefully before using the appliance.
☐ Check that your mains voltage corresponds to that stated on the rating plate of the appliance.
☐ Do not leave the heater unattended during operation and keep children away.
From time to time check the cord for damages. Never use the appliance if cord or appliance shows any signs of damage but have it checked and repaired by a competent qualified service(*). Should the cord be damaged, it must be replaced by a competent qualified service (*)
☐ Only use the appliance for domestic purposes and in the way indicated in these instructions.
☐ Never immerse the appliance or the remote control in water or any other liquid for any reason whatsoever. When cleaning the appliance, refer to the instructions in the paragraph "Cleaning and care" because the water penetration in the appliance can be very dangerous.
☐ Never use the appliance near hot surfaces.
Before cleaning and when you do not use the appliance, always unplug the appliance from the power supply. Do not attempt to remove the plug from the wall socket with wet hands.
□ Never use the appliance outside and always place it in a dry environment.
☐ Never use accessories that are not recommended by the producer. They could constitute a danger to the user and risk to damage the appliance.
☐ Never move the appliance by pulling the cord. Make sure the cord cannot get caught in any way. Do not wind the cord around the appliance and do not bend it.
☐ No responsibility is accepted if damage results from improper use, or if these instructions are not complied with.
☐ Stand the appliance on a stable surface so that it cannot fall.
☐ Do not place the appliance under a power socket. The power socket must not be in the hot airflow of the appliance.
□ Always position the heater in such a way that inflammable materials (such as curtains) cannot be ignited. Ensure at all times that the unit is placed solidly on its base. Make sure that the air inlet and outlet openings are not blocked. To avoid any risk of fire, do not cover the heater (ex. With clothes).
☐ The heater should only be operated at a minimum distance of 50cm from any wall or other object and of 1 meter from combustibles.
☐ Warning: Do not operate the heater near baths, showers, washbasins, swimming pools or any other water container. It must be impossible to reach the commands of your appliance when you are in contact with water.
☐ The temperature of the grids may be very high when the appliance is in use. Avoid contact with the skin.
☐ Do not allow the power cord to touch any hot part of the appliance.
□ Never use the appliance near inflammable or explosive materials.
☐ Do not insert any objects through the grille or into the interior of the appliance.
☐ Do not use double adapters or other appliances to connect with heater.

POSITIONING OF THE APPLIANCE

The heater should only be operated at a minimum distance of 50cm from any wall or other object. Position the air flow in order to optimise the heating of the room. Avoid corners, small volumes, floors and ceilings.

BATTERIES

• In order to be able to use the remote control, you first have to insert the batteries in it. To do so:
• Open the battery compartment.
• Insert the batteries, making sure you respect the + and - polarity.
• Close the compartment. Use 2 AAA-type batteries of 1.5 V. Never mix up new and old batteries or batteries of different types.
• When you decide to throw away the appliance, make sure to remove the battery and to dispose of it in an ecological manner by handing it in a place intended for this end.

Caution: if you don't use your remote control for a long time, it is recommended to remove the batteries because they could run.

USE

When the appliance is switched on for the first time, a slight smell may be emitted. Please ensure sufficient ventilation. This smell will disappear very quickly.

The Heater may be operated by the manual controls located on the heater or by your remote control.

1. Place the heater on a firm level surface.
2. Set the main power switch to 'OFF'. Plug in the appliance. Turn the main power switch to 'ON' ("I") position. A beep will sound and the red light will come on indicating that there is power to the unit. The heater is ready for use. The red light will remain lighted until the main power switch is turned OFF ("0") and the Heater is unplugged from the electrical outlet.
3. Turn the heater ON by pressing the ON/OFF button of the remote control or control panel. The unit will display the current room temperature.
4. Upon turning the heater on, the unit will be in the FAN heat mode.
5. Pressing the 'HEAT MODE' button at this point will set the Heater into LOW HEAT mode.
6. Pressing the 'HEAT MODE' button a second time more will set the Heater into HIGH HEAT mode. Pressing a third time sets the heater in AUTO mode. Notice that the display now displays a 'SET TEMP' indicator. (See Thermostat Instructions) To turn the heater OFF, press the ON/OFF button.

Swing function

This function will work in any mode. Pressing the swing button will allow the heater to oscillate left and right. To stop the oscillation, press the swing button once more.

Timer function

This function will work in any mode. The timer function allows you to set the length of operation from 1 hour to 8 hours. Pressing the timer button increases the length of operation by 1 hour each time the button is pressed. Once the timer has been set, the timer will count down the hours in 1 hour increments, showing on the display the remaining operating time until the

Heater will turn itself off. Pressing the timer button once more after the display reflects 8 hours will reset the Heater to continuously running.

Thermostat instructions

1. Press the HEAT MODE button until the display shows AUTO
2. To adjust "SET TEMP", press the +/up button to increase the desired temperature and the -/down button to decrease the desired temperature.
3. When the air temperature reaches 3 degrees above the SET TEMP, the heater will cut off.
4. When the air temperature drops 1 degree below the SET TEMP, the unit will come back on.

Note: It is normal for the heater to cycle ON and OFF as it maintains the SET TEMP.

SAFETY DEVICES

• Your appliance is fitted with a safety device (tip-over switch situated on the bottom of the appliance) that disconnects your appliance when it is tilted or tipped. If your appliance falls, switch it off, replace it correctly and switch it on again.
• This heater is also protected with an overheat protection that switches off the appliance automatically in case of overheat, e.g. due to the total or partial obstruction of the grids. In this case, unplug the appliance, wait about 15-20 minutes for it to cool and remove the object that is obstructing the grids. Then switch it back on as described above. The appliance should operate normally. Should the problem persist, please contact the nearest customer service.

MAINTENANCE AND CLEANING

• Before cleaning the appliance, ensure it is disconnected from the power supply and has cooled down completely.
• The housing may be wiped with a slightly damp, lint-fee cloth; do not use any abrasive scouring pad or steel wool.
  • The grids are particularly delicate; to clean them you can carefully use a vacuum cleaner.
• When you do not use the appliance, place it in a dry environment.

Copies of the I/B. Please reproduce them without any changes except under special instruction from Team International BELGIUM. The pages must be reproduced and folded in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm height). When folding, make sure you keep the good numbering when you turn the pages of the I/B. Don't change the page numbering. Keep the language integrity.

Fax [phone]

Función minutero