PT798SBA - Home Theater Pyle - Free user manual and instructions

Product Type	Home Theater System with Bluetooth, DVD, AUX, FM/AM, and USB (not specified)
Model	Pyle PT798SBA
Dimensions (Subwoofer)	420 x 380 x 260 mm
Dimensions (Front L/R Speakers)	140 x 140 x 290 mm each
Dimensions (Surround Speakers)	140 x 140 x 290 mm each
Dimensions (Center Speaker)	400 x 75 x 100 mm
Net Weight	38.8 lbs (17.6 kg)
Gross Weight	43.6 lbs (19.8 kg)
Power Output (Peak)	Front: 400W x2, Center: 400W x1, Surround: 400W x2, Subwoofer: 500W x1
Drive Units	Satellite: 3.0 inch, Subwoofer: 10 inch
Frequency Response	Satellite: 150Hz-20kHz, Subwoofer: 40Hz-330Hz
Signal-to-Noise Ratio	85 dB
Total Harmonic Distortion	0.1%
Bluetooth	Built-in receiver, device ID: bluespeaker, password: 0000
Input Sources	DVD, AUX1, AUX2, FM, AM, Bluetooth
Display	VFD (Vacuum Fluorescent Display) with spectrum and channel indicators
Remote Control	Pull-function remote with full control
Channel Adjustment	Individual volume, treble, and bass for each channel
Speaker Cabinet Material	Satellites: Plastic, Subwoofer: Wooden
Finish	Black
Magnetic Shielding	Center speaker magnetically shielded; others not shielded
Power Supply	AC, operating voltage indicated on rear panel
Battery for Remote	2 x AAA (not included)
Cleaning	Soft cloth slightly moistened with mild detergent; avoid abrasives, alcohol, benzene
Safety Features	Auto shut-off on irregular current, protective circuit, replaceable fuse
Warranty / Service	Contact nearest Pyle dealer for service

Frequently Asked Questions - PT798SBA Pyle

How do I pair my phone via Bluetooth?

Press the 'Bluetooth' button or the '●' key on the remote control to enter pairing mode. The VFD will show 'pairing' and flicker. On your phone, search for 'bluespeaker' and connect with password 0000.

Why is there no sound from the speakers?

Ensure the correct input source is selected (e.g., DVD, AUX, Bluetooth). Check that speaker wires are securely connected. Verify the system is not muted (press MUTE) and master volume is turned up.

How do I adjust the volume for individual channels?

Use the remote control keys: MASTER VOL for overall volume, SIDE LEFT, SIDE RIGHT, CENTER, SUBWOOFER, REAR LEFT, REAR RIGHT for each channel. Press the corresponding key, then use -/+ to adjust.

Can I use the system without the subwoofer?

Yes, you can select 2.1CH or 5.1CH mode via the Source Output Selector. In 2.1CH, side and center speakers are muted; in 5.1CH, only side speakers are muted. The subwoofer remains active.

What should I do if the remote control stops working?

Replace the AAA batteries with new ones. Ensure there are no obstacles between the remote and the receiver. Point the remote directly at the front panel sensor.

How can I improve FM/AM radio reception?

Fully extend the FM/AM antenna on the rear panel. If reception is poor, consider using an outdoor antenna. Avoid connecting the system to an outdoor antenna during rain.

Why does the display show 'Protect' and shut off?

The 'Protect' message indicates an irregular current to the speakers. Check speaker connections for shorts. After a few seconds, the receiver will turn off automatically. Correct the issue and restart.

How do I clean the unit?

Use a soft cloth slightly moistened with a mild detergent solution. Do not use abrasive pads, scouring powders, alcohol, or benzene.

What are the dimensions of the subwoofer?

The subwoofer measures 420 x 380 x 260 mm (16.5 x 15.0 x 10.2 inches).

Is the center speaker magnetically shielded?

Yes, the center speaker is magnetically shielded, allowing it to be placed near a TV. The front, surround, and subwoofer speakers are not shielded; keep them at least 1-2 feet from the TV to avoid color distortion.

USER MANUAL PT798SBA Pyle

Bluetooth Receiver

Black audio/video audio setup with multiple speakers and a CD-ROM (no visible text or symbols)

PT798SBA

Bluetooth

Owner's Manual

TABLE OF CONTENTS

Important Safety Information

Owner's Record....1

For Customers in the United States....1

Caution....1

Note to Home Theater System Installer....1

Installation

Front Panel Display Window....2

Rear Panel Connectors....3

Battery Installation....4

Using the Remote Control....5

Basic Operations

Turn On/Off the Power....6

Master Volume Control....6

Side Left Channel Volume Control....6

Side Right Channel Volume Control....6

Center Channel Volume Control....6

Subwoofer Volume Control....6

How to Adjust Treble....6

How to Adjust Bass....6

How to Play DVD 6

How to Play Bluetooth....6

How to Play AUX....6

How to Play Tuner....6

Select Program

Listen to the Preset Program

Memory Program

How to Mute....7

Introduction of DSP Control Key 7

Introduction of Source Output Selector Area....7

How to Pair the bluetooth receiver....7

Additional Information

Precautions....8

Troubleshooting....10

Specifications. .12

Important Safety Information

OWNER'S RECORD

The model and serial number are located on the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Pyle regarding this product.

Model No.

Serial No.

FOR CUSTOMERS IN THE UNITED STATES

This symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure, it may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

You are cautioned that changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

• To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
• To prevent fire, do not cover the ventilation of the apparatus with newspapers, table-cloths, curtains and etc. Do not place lighted candles on the apparatus.
• To prevent fire or shock hazard, do not place objects filled with liquid, such as vases, on the apparatus.
• Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
• Install this system so that the power cord can be unplugged from the wall socket immediately in the event of trouble.
• Batteries or batteries installed apparatus shall not be exposed to excessive heat such as sunlight or fire.

Note to Home Theater System Installer:

This reminder is provided to call Home Theater System installers' attention to Article 820-40 of the NEC that provides guidelines for proper grounding, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as possible.

INSTRUCTION OF CONTROL PANEL

1. Bluetooth device ID and pass word.
2. Main channel volume adjust knob: Increase/Decrease the main channel volume.
   3.VFD display panel.
3. Bluetooth working light: Flashing rapidly when pairing with the other bluetooth unit.

INDICATORS ON FRONT PANEL DISPLAY WINDOW

Name

1STEREO	AUX/TUNER INPUTBluetooth
2AC-3 PROLOGIC	DVD INPUT
3DSP	DSP STATE ICON
4DIGITAL DISPLAY
5KHz/MHz	KHz/MHZ ICON
6SPECTRUM DISPLAY

Function

Lights up when input mode is set to AUX1, AUX2, Bluetooth.

Lights up when input mode is set to 5.1 channel or DVD.

Lights up when play DSP effect.

Lights up to display value of current input mode.

Lights up when Tuner input is selected and indicates the value on the display for KHz/MHz.

Lights up to display the spectrum of different sound channels.

REAR PANEL CONNECTORS

Please install this system according to the following schematic diagram.

1. On the back of the remote control, push the tab and lift off the battery cover.
2. Obtain two (2) fully-charged AAA batteries. Match the "+" and "-" marks on the batteries to the "+" and "-" marks in the battery case, then insert the new batteries.
3. Align the cover keys with the case holes and press the cover back into place. The tab should click when the cover is locked.
4. Test the unit by pressing POWER or any mode key. If the batteries are inserted correctly, the selected mode key will blink once.

Line drawing of two open remote control devices with blades and a clip emerging from their sides (no text or symbols)

Notes

• Do not leave the remote control in an extremely hot or humid place.
  • Do not use a new battery with old ones.
• Do not mix manganese batteries with other kinds of batteries.
• Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction.
• If you do not intend to use the remote control for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.
• When you replace the batteries, the remote buttons may be reset to their factory settings. If this happens, reset the buttons again.

Tips

Under normal conditions, the batteries should last for about 3 months. When the remote no longer operates the receiver, replace all the batteries with new ones.

1. POWER Button-Toggle Power OFF and ON		2. DSP Control Button
		13. AM/FM Input Selector
3. TUNER Number Button		14. MEMORY Button
4. INPUT MODE Selector Area
5. TREBLE Volume Increase Button	3——4——5——6——7——8——9——10——11——12——	15. TUNER Band Adjustment Button
		16. CHANNEL SOURCE OUTPUT Selector Area
6. MASTER Volume Control Button		17. BASS Volume Increase Button
7. LEFT Balance Selector Button		18. RIGHT Balance Selector Button
8. TREBLE Volume Decrease Button		19. MUTE Control Button
9. REAR LEFT Volume Adjustment Button		20. BASS Volume Decrease Button
10.SIDE LEFT Volume Adjustment Button		21. REAR LEFT Volume Adjustment Button
11. CENTER Volume Adjustment Button		22. SIDE RIGHT Volume Adjustment Button
12. Bluetooth Control Area		23. SUBWOOFER Volume selector Button

Basic Operation

Turn On/Off the Power

POWER

Press " 🔍 " key to control the power on and off.

Master Volume Control

Press the “VOL+” or “VOL-” Key to adjust the main channel volume.

Rear Left Channel Volume Control

Ruer Left Vol.

Press “- + ” key on the remote control, screen display the RL volume, press "-ADJUST+" key to adjust side left channel volume.

RearRight Channel Volume Control

Rear Right Vol.

Press "●" Key on the remote control, screen display the RR volume, press "-ADJUST+" key to adjust side right channel volume.

Side Left Channel Volume Control

Side Left Vol.

Press “-” key on the remote control, screen display the SL volume, press “-ADJUST+” key to adjust side left channel volume.

Side Right Channel Volume Control

Side Right Vol.

Press " - + "Key on the remote control, screen display the SR volume, press "-ADJUST+" key to adjust side right channel volume.

Center Channel Volume Control

Center Vol.

Press "→" key on the remote control, screen display the CEN volume, press "-ADJUST+" key to adjust center channel volume.

Subwoofer Volume Control

SW Vol.

Press "→" key on the remote control, screen display the SW volume, press "-ADJUST+" key to adjust subwoofer channel volume.

How to Adjust Treble

TroB4

Tree-

Press "●●" key to adjust the treble output of the main channel.

How to Adjust Bass

B

Bass

Press "●●" key to adjust the bass output of the main channel.

How to Play DVD

Make sure DVD connection lines are correct, Press the "☐" key to play DVD.

How to Play AUX

DVD

Make sure AUX1/AUX2 connection lines are correct, Press the “☐ / ☐” key to play AUX.

How to Play Bluetooth

Paring with a bluetooth sender as the following manual.

1. "M" play the previous song.
2. "M" play the next song.
3. " play/pause the song.
4. "●" paring the bluetooth sender.

How to Play Tuner

1. Select Program

Use "AM/FM" key to select AM/FM band. Press the "SCAN" key to adjust the band of tuner.

Press the “SCAN” key for 2 seconds, the AM/FM will search automatically. You can press

the “SCAN” key once or the input mode selector to stop the function.

2. Listen to the Preset Program

Press the number keys "10 11 12" to select the radio program that you already saved.

Once selected, screen will display the radio program's frequency in the memory area.

3. Memory Program

When you receive a clear radio program, press the "MEMORY" key first, and then the

screen displays the "Memory" icon. Press one of the 12 "⑩ ⑪ ⑫" number key on the remote control to select the memory station. If you want to extract the channel you saved, just press the number key you selected.

How to Mute

Press "MUTE" key to turn sound off/on.

Press again to restore the audio to the original level.

Introduction of DSP Control Key

Press the key “DSP” repeatedly to switch to different operations: Live, Hall or Church. All the above functions can give different sound effects.

Introduction of Source Output Selector Area

• Press "7.1CH" to receive 7.1 channel. (7.1 channel output is the default mode)
• Press "5.1CH" to receive 5.1 channel. (Side left speaker and Side right speaker mute)
• Press "2.1CH" to receive 2.1 channel. (Side left speaker, Side right speaker and Center speaker mute)

How to Pair the bluetooth receiver

The subwoofer have built in a bluetooth receiver. If you need to pair with a bluetooth sender(mobile phone), first open the subwoofer, and press the "●" key on the remote control, the VFD will show "pairing" and flicker. Then search the bluetooth receiver(Device ID:bluespeaker) by your own bluetooth sender and connect them by the password:0000. After that, you can enjoy the music by the bluetooth receiver. The system will turn to the normal working statue if no paring in 10 minutes.

Additional information

PRECAUTIONS

On Safety

- Should any solid object or liquid fall into the receiver, unplug the receiver and have it checked by qualified personnel before operating it any further.

On Power Sources

• Before operating the system, check that the operating voltage is identical with your local power supply.
  • The operating voltage is indicated on the back of the speakers.
• As long as the unit is not removed from the wall outlet, the unit will not be disconnected from the AC power source (main) even if the unit itself has been turned off.
• If you are not going to use the system for a long time, be sure to disconnect the system from the wall outlet. To disconnect the AC power cord, disconnect by grasping the plug itself; never pull the cord.
  • One contact prong of the plug is wider than the other for safety purposes, which will fit into the wall outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.
  • The AC power cord should only be changed at a qualified service shop.

On Heat Buildup

- Although the system heats up during operation, this is not a malfunction. If you continuously use this system at a large volume, the receiver temperature on top, side and bottom may rise considerably. To avoid burning yourself, do not touch the receiver.

On Placement

• Place the system in a location with adequate ventilation to prevent heat buildup and to prolong the life of the system.
• Do not place the system near heat sources or in a place subject to direct sunlight, excessive dust, or mechanical shock.
• Do not place anything on top of the receiver that might block the ventilation holes and cause malfunctions.
• Do not place the system near equipments such as a TV, VCR, or tape deck. (If the system is being used in combination with a TV, VCR or tape deck, and is placed too close to such equipment, noise may occur and picture quality may suffer. Especially, when using an indoor antenna).
  • Use caution when placing the system or speakers on surfaces that have been specially treated (with wax, oil, polish, etc.) as staining or discoloration of the surface may result.

On Operation

• Before connecting other components, be sure to turn off and unplug the system.
• The center speaker is magnetically shielded to allow it to be installed near a TV set. However, color irregularities may still be observed on certain types of TV sets.
• As the front speakers, center speaker and the subwoofer are not magnetically shielded, we recommend that you place them slightly further away from the TV set.
- If color irregularity is observed, turn off the TV set then turn it on again after 15 to 30 minutes.

• If color irregularity is observed again, then place the speaker further away from the TV set.
• If howling occurs, reposition the speakers or turn down the volume on the receiver.

On Cleaning

• Clean the receiver panel, and controls with a soft cloth slightly moistened with mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzene.
• If you have any questions or problems concerning your system, please consult your nearest Pyle dealer.

Use this chart to help you solve operational problems. If there are any problems that can not be solved, please contact Service Center.

Problem	Possible Reasons	Solutions
Can't get through power supply	The plug is not inserted properly.	Check power supply and plug.
	The socket has no power.	Check socket and power supply.
Display can't be turned on
	The fuse is broken.	Replace the fuse.
	Have not pressed "POWER" button.	Press the "POWER" button again.
No sound at all	Incorrect selection of input signal.	Read the manual carefully again.
	The wire and lead are not connected correctly.	Check the wire and lead.
	The mute state is turned on.	Turn off the mute state.
	Sound source machine is not powered.	Turn on the power of sound source.
Neither of the main channels have sound	The speaker line is not connected properly.	Read the manual.
	The signal plug is connected incorrectly or lines are short-circulted.	Check the connection of the signal plug.
Center channel has no sound.	The speaker line is not connected properly.	Read the manual.
	Mode is not set properly.	Mode should be set that the center channel has output.
Side Surround channels have no sound	The speaker line is not connected properly.	Read page 3 of the manual.
	Mode is not set properly.	Mode should be set that the surround channel has output, for example, 5.1 channel.
The sound of surround channel is low	The sensitivity of speakers is too low.
	The volume is set too low.	Reset volume.
	The input signal is STEREO.	Change to 5.1 channel.
The sound of center channel is low.	The sensitivity of speakers is too low.
	The volume is set too low.	Reset volume.
Sound from speakers is out of order	Speakers are located inappropriately.	Read the manual.
	The lines are not connected properly or the Disc is defective.
Can't operate or display normally	Affected by exterior strong disturbance.	Turn off first then turn on again.
		Avoid direct sunlight/heat.
No sound when play with bluetooth	No pacing with a bluetooth sender.	Repairing with the bluetooth sender.
	No play music by a bluetooth sender.	Play music by the bluetooth sender.
	The input signal is not bluetooth.	Choose the bluetooth input mode.
Radio
The FM/AM reception is poor.	Need outdoor antenna.	Stretch the FM/AM antenna of the receiver in the rear panel. But please don't connect the receiver to an outdoor FM/AM antenna on raining days.
Radio stations cannot be tuned in.	Check that the antennas are connected securely.	Adjust the antennas and connect an external antenna, if necessary.
	The signal strength of the stations is too weak (when tuning in with automatic tuning).	Adjust manually
	No stations have been preset or the preset stations have been cleared (tuning by scanning preset stations).	Make sure you set the tuning interval correctly.
The remote control does not function.	Obstacles exist between the remote and the receiver.	Remove any obstacles in the path between the remote and the receiver.
	The remote batteries are weak.	Replace all batteries in the remote control with new ones.
	Incorrect input selection on the remote control.	Make sure you select the correct input on the remote control.
Error messages	If appears a message, there may be a malfunction.	You can check the condition of the system by the message.
	Should any problems persist.	Consult your nearest dealer.
Protect	Irregular current is output to the speakers. The receiver will automatically turn off after a few seconds.	Check the speaker connection then turn on the power again.
If you are unable to remedy the problem using the troubleshooting guide		Clearing the receiver's memory may remedy the problem. Note that all memorized settings will be reset to their initial settings on the receiver.
If the problem persist		Take the complete appliance to the nearest dealer for advice.

Powered Home Theater PT798SBA

Functions	Specifications
DVD	DVD input
AUX1,AUX2	AUX input
FM/AM	FM/AM built-in
Bluetooth	Bluetooth input
Magnetically Shielded	Yes
Display	VFD display
Remote Control	Pull function remote control
Adjustment	Every channel adjusts separately
Output Power	Front 400W-PEAK x2
	Center 400W-PEAK x1
	Surround 400W-PEAK x2
	Subwoofer 500W-PEAK x1
Drive Unit	Satellite: 3.0 inch
	Subwoofer: 10 inch
Frequency Response	Satellite: 150Hz-20kHz
	Subwoofer: 40Hz-330Hz
S/N	85dB
TED	0.1%
Box Material	Satellite: plastic
	Subwoofer: wooden
Size	Subwoofer: 420 x 380 x 260mm
	L, R channel: 140 x 140 x 290mm
	Surround channel: 140 x 140 x 290mm
	Center channel: 400 x 75 x 100mm
Weight	N.W.: 38.8lbs
	G.W.: 43.6lbs
Finishes	Black

Pyle AV receivers patent pending technologies are for the world's finest music and home theater systems. All models patent pending. All product titles, publisher's names, artwork, logos and associated images are the trademarks and/or copyright material of their respective owners. All rights reserved. Suggested prices don't represent a bonafide selling price in the metro trading area. Model number, specifications and prices are subject to change without notice.