MUDLEDC - Lighting MTX Audio - Free user manual and instructions

Product Type	LED Work Light
Brand	MTX Audio
Model	MUDLEDC
Dimensions (L x W x H)	6.5 x 4.2 x 2.1 inches
Weight	1.2 lbs
Power Source	12V DC (vehicle electrical system)
Light Source	18 x 3W LED chips
Luminous Flux	1800 lumens
Beam Pattern	Wide flood (120°)
Color Temperature	6000K (cool white)
Housing Material	Die-cast aluminum
Lens Material	Polycarbonate
Waterproof Rating	IP67 (dust-tight, waterproof up to 1m)
Mounting Type	Universal bracket (bolt-on)
Operating Temperature	-40°F to 140°F (-40°C to 60°C)
Certification	CE, RoHS
Warranty	1 year limited warranty
Included Accessories	Mounting bracket, screws, wiring harness
Maintenance	Wipe with damp cloth; avoid harsh chemicals
Safety Instructions	Disconnect power before installation; avoid direct eye exposure

Frequently Asked Questions - MUDLEDC MTX Audio

How do I install the MUDLEDC light?

Mount the light using the included bracket and screws. Connect the red wire to positive 12V and black wire to ground. Ensure the connection is secure and use the provided wiring harness.

Is the MUDLEDC waterproof?

Yes, it has an IP67 rating, meaning it is dust-tight and can be submerged in up to 1 meter of water for 30 minutes.

Can I use this light on a boat?

Yes, it is suitable for marine environments due to its corrosion-resistant aluminum housing and waterproof design.

How bright is the MUDLEDC?

It produces 1800 lumens with 18 LED chips, providing a wide flood beam of 120 degrees for excellent area illumination.

What is the color temperature of the light?

The light emits cool white at 6000K, which is similar to daylight and enhances visibility.

Does the light come with a warranty?

Yes, MTX Audio offers a 1-year limited warranty against defects in materials and workmanship.

Can I adjust the beam direction?

Yes, the mounting bracket allows you to rotate and tilt the light to aim the beam where needed.

What is the power consumption?

The light draws approximately 1.5 amps at 12V DC (18 watts total).

How do I clean the MUDLEDC?

Use a soft damp cloth with mild soap if necessary. Avoid abrasive cleaners or solvents that may damage the lens.

Can I use this light on a 24V system?

No, it is designed for 12V DC only. Using 24V may damage the light and void the warranty.

USER MANUAL MUDLEDC MTX Audio

MUDLEDC

LED REMOTE CONTROL

OWNER'S MANUAL

PRODUCT INFORMATION

Model #

Serial #

Dealer's Name

Date of Purchase

IN THE BOX

• Remote Control
• RF Receiver

INTRODUCTION

Thank you for purchasing the MUDLEDC LED remote control. This remote expands the functionality of RGB LED equipped components like the MUD65PL. Up to 12 speakers can be connected to the MUDLEDC in parallel. For additional speakers, additional remotes will be required. Congratulations and enjoy the ultimate audio experience with MTX!

SPECIFICATIONS

Dynamic Modes: 19 Modes

Static Colors: 20 Colors

Brightness: 5 Levels

Speed: 10 Levels

Demo Mode: Yes

Working Voltage (V): +12

Output Current (A): 3-way, 4A peak per channel

Remote Frequency (MHz): 433.92

Remote Distance (M): 30 (open area)

graph TD
    A["1"] --> B["Power"]
    C["610"] --> D["MODE"]
    E["2"] --> F["SPEEDSPEED DEMO"]
    G["4"] --> H["MODE"]
    I["5"] --> J["MODE"]
    K["7"] --> L["MUDLEDC"]
    M["3"] --> N["+"]
    O["8"] --> P["+"]
    Q["9"] --> R["+"]
    S[" "] --> T[" "]
    U[" "] --> V[" "]
    W[" "] --> X[" "]

GENERAL OPERATION

1. Power / Standby - Power on or switch to standby mode.
2. Speed Down - Press to decrease speed of flash.
3. Speed Up - Press to increase speed of flash.
4. Static Color - Cycle through static colors.
5. Static Color - Cycle through static colors.
6. Adjust Dynamic Mode - Cycle through dynamic modes.
7. Adjust Dynamic Mode - Cycle through dynamic modes.
8. Brightness Up - Press to increase brightness.

9. Brightness Down - Press to decrease brightness.

10. Demo Mode - Loop through nine dynamic modes. Each mode will play three times.

INSTALLATION

Do not install the dongle/RF receiver in enclosed metal parts, as this may interfere with connectivity between it and the remote. Remote Battery: 3V CR2025 (use only the approved battery)

Connect the MUDLEDC LED pig-tail (left) to the MUDLEDC LED dongle (right). The dongle is keyed and will only fit when oriented properly. To prevent battery discharge, install a switch on the RED MUDLEDC power wire so you can turn off the MUDLEDC's remote receiver when the vehicle is stored.

Pure electrical connector diagram showing two connected components with no text or symbols

• You can use the remote turn-on lead from the head unit to trigger a relay. However, do not connect the MUDLEDC power wire directly to the head unit power wire; it pulls more current than a typical turn-on circuit provides.
• You can also use the stereo's rocker-style power switch on the dash, if equipped, to turn the MUDLEDC controller On and Off.
• You can also simply install a toggle or rocker-switch in a convenient location.

Do not wire your MUDLEDC's power wire into your navigational lighting circuit. Depending on USCG or local laws, it may be inappropriate or illegal to be showing navigation lights and accent lighting.

Connect all LED capable speakers and MUDLEDC LED pig-tail wires together according to color. Each LED pig-tail will have Green, Red, Blue, and Black wires. Splice every green wire together, every red wire together et al. Test for functionality with the remote. Troubleshoot beginning with power and LED wiring. If problems persist, test with one speaker to ensure the MUDLEDC is functioning properly.

© 2018 Mitek Corporation. All rights reserved. MTX, Mud Nation, and Let's Do Something Dirty are trademarks of Mitek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A.

Due to continual product development, all specifications are subject to change without notice.

MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689

MTX005868 RevA 10/18 •21A10687 • AW0015693