SS-BCL - Loudspeaker Soundsphere - Free user manual and instructions

Product Type	Wireless Bluetooth Speaker
Brand	Soundsphere
Model	SS-BCL
Dimensions (W x H x D)	250 x 150 x 120 mm
Weight	1.5 kg
Power Output	20 W RMS
Frequency Response	80 Hz - 20 kHz
Impedance	4 Ohms
Connectivity	Bluetooth 5.0, AUX 3.5 mm, USB-C (charging)
Battery	Lithium-ion 2200 mAh, up to 8 hours playtime
Charging Time	Approximately 3 hours
Controls	Power, Volume +/-, Play/Pause, Bluetooth pairing
Housing Material	Plastic with fabric grille
Water Resistance	IPX5 (splash-proof)
Compatible Devices	Smartphones, tablets, laptops
Included Accessories	USB-C charging cable, user manual
Safety Features	Overcharge protection, short-circuit protection
Cleaning Instructions	Wipe with a dry cloth; do not use abrasive cleaners
Repairability	Refer to authorized service center; no user-serviceable parts

Frequently Asked Questions - SS-BCL Soundsphere

How do I pair my Soundsphere SS-BCL speaker via Bluetooth?

Turn on the speaker by pressing the Power button. The LED will flash blue. On your device, enable Bluetooth and select Soundsphere SS-BCL from the list. The speaker will confirm with a tone.

What is the battery life of the SS-BCL?

The built-in lithium-ion battery provides up to 8 hours of playback at moderate volume. Charging takes about 3 hours via the USB-C port.

Can I use the speaker while it is charging?

Yes, you can use the speaker while connected to a power source. However, to preserve battery health, it is recommended to fully charge before extended use.

Is the Soundsphere SS-BCL waterproof?

The speaker has an IPX5 rating, meaning it is splash-proof. It can withstand light rain or sweat, but should not be submerged in water.

How do I clean the speaker?

Use a soft, dry cloth to wipe the exterior. For the fabric grille, gently brush away dust. Do not use water, solvents, or abrasive cleaners.

What should I do if the speaker does not turn on?

Ensure the battery is charged by connecting the USB-C cable to a power source. If still no response, press and hold the Power button for 10 seconds to reset. If the issue persists, contact support.

Can I connect two Soundsphere SS-BCL speakers for stereo sound?

This model does not support wireless stereo pairing. For stereo sound, use a single speaker in a suitable location or connect via AUX to external speakers.

How do I reset the speaker to factory settings?

With the speaker on, press and hold both Volume + and Volume - buttons simultaneously for 5 seconds. The LED will flash red and the speaker will restart with all pairings cleared.

What is the range of Bluetooth?

The Bluetooth 5.0 connection has a range of approximately 10 meters (33 feet) in open space. Walls and obstacles can reduce this range.

Where can I find the user manual for the SS-BCL?

The manual is available for free download as a PDF on notice-facile.com. You can also request a translated version by selecting your language and providing your email.

USER MANUAL SS-BCL Soundsphere

Install Instructions

Please read this Installation Guide and the attached manufacturer's Installation Instructions carefully. These guidelines apply to the following product only: CADDY®, Flange Clamp, model 4-H-2-4 (4H24).

• Follow the manufacturer's installation instructions for proper installation techniques and use of this product (see page 2).
• This product is designed to be installed only on beam flanges that are between 1/8" and 1/4" thick (0.125 - 0.250 inches or 3.17 - 6.35mm).
• The Maximum Static Load (MSL limit) is 200 pounds (90.9 kg). The MSL applies to the clamp only - all other fasteners must meet or exceed that weight load rating.
• Never exceed the Safety Factor Limits of this product. Always allow a load safety factor based on local, state, and/or Federal codes and regulations
• The clamps are designed for axial loads only (see page 2 illustrations). Lateral or side loading must be avoided.
• Ensure the clamps are installed properly. They must not be forced onto a flange that is too thick (more than 1/4", 0.250" or 6.35mm). They must not be used on a flange that is too thin (1/8", 0.125" or 3.17mm). Measure the flange if in doubt of its thickness.
• Always visually inspect clamp installation. Check to ensure that the clamp is installed square with the flange. Check to ensure that the clamp is secure after installation.
• Never strike the clamp with a hammer or other metallic device.
  • These clamps are designed for indoor use in non-corrosive environments only.

WARNING

Be sure to securely tighten all appropriate hardware on loudspeakers, suspension systems, boo supports, mounting brackets, etc. when installation overhead systems. Wire rope, thimbles and clips with saddles of suitable strength are the recommended materials for overhead suspension. Chain and rope are not recommended, nor do we ever specify them, for the purpose of installing overhead loudspeaker systems. All loudspeakers should be redundantly safety wired to structural members of the building.

*Agency inspection of a new or renovated installation is usually required by most municipalities. Always check local (and all other applicable) safety codes before installing any overhead loudspeaker system.

Misuse or misapplication may cause product failure, resulting in property damage and/or bodily injury.

Please read the attached manufacturer's Installation Instructions and Warning.