MOR-36 - Uncategorized Pico Macom - Free user manual and instructions
Find the device manual for free MOR-36 Pico Macom in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | RF Modulator/Processor for CATV/SMATV systems |
| Model | MOR-36 |
| Brand | Pico Macom |
| Rack Mountable | Yes, 19-inch standard rack, 1U height |
| Dimensions (W x D x H) | 19 x 10 x 1.75 inches (483 x 254 x 44 mm) |
| Weight | Approximately 5 lbs (2.3 kg) |
| Power Supply | 120V AC, 60 Hz, 15W max |
| Input Frequency | 50-1000 MHz |
| Output Frequency | 54-1000 MHz |
| Input/Output Impedance | 75 Ohms |
| Input/Output Connectors | F-type female |
| Gain | Adjustable, up to 30 dB |
| Noise Figure | < 8 dB |
| Operating Temperature | 0°C to 50°C (32°F to 122°F) |
| Cooling | Passive (no fan) |
| Main Functions | Signal processing, modulation/demodulation, amplification, filtering |
| Control Interface | Front panel knobs and switches, rear panel adjustment |
| LED Indicators | Power, signal level, fault |
| Compliance | FCC Part 15, CE |
| Maintenance | Wipe with dry cloth; keep vents clear |
| Repair Parts | Contact Pico Macom service center; no user-serviceable parts inside |
Frequently Asked Questions - MOR-36 Pico Macom
What is the Pico Macom MOR-36 used for?
The MOR-36 is an RF modulator/processor designed for CATV and SMATV systems. It processes and distributes video and audio signals over coaxial cable networks.
How do I install the MOR-36 in a rack?
Use standard 19-inch rack rails. Mount the unit with four screws (not provided). Ensure adequate ventilation and secure all cable connections before powering on.
What power cord does the MOR-36 need?
The unit uses a standard IEC C13/C14 power cord for 120V AC, 60 Hz. Verify local voltage compatibility before use.
Can the MOR-36 be used outdoors?
No, it is designed for indoor use only. Operating temperature range is 0°C to 50°C, and it must be kept dry.
How do I adjust the gain on the MOR-36?
Gain is adjustable via a front panel trim pot or rear panel control. Use a small screwdriver to turn clockwise to increase gain, counterclockwise to decrease.
What type of connectors does the MOR-36 use?
All RF input/output connectors are F-type female (75 Ohm). Use F-type male connectors with proper crimping or compression.
Why is the fault LED lit?
A lit fault LED indicates signal loss, overdrive, or internal failure. Check input signal level and cable connections. If issue persists, contact support.
Can I bypass the MOR-36 for maintenance?
The MOR-36 may have a bypass switch or can be temporarily removed from the signal path by connecting input directly to output with a coupler. Refer to your system design.
Is the MOR-36 compatible with digital signals?
Yes, it supports both analog and digital (QAM) signals within its 50-1000 MHz frequency range, provided proper modulation settings are used.
Where can I find the user manual?
The user manual is available for free download on notice-facile.com in PDF format. Search for 'Pico Macom MOR-36'.
User questions about MOR-36 Pico Macom
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual MOR-36 - Pico Macom and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. MOR-36 by Pico Macom.