SuperServer E403-9D-12C-FN13TP - Server Supermicro - Free user manual and instructions
Find the device manual for free SuperServer E403-9D-12C-FN13TP Supermicro in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Rackmount Server |
| Form Factor | 1U |
| Dimensions (W x D x H) | 17.2 in x 25.5 in x 1.7 in (437 mm x 648 mm x 43 mm) |
| Net Weight | 28 lbs (12.7 kg) |
| Power Supply | Redundant 800W Platinum Level |
| Processor | Intel Xeon D-1557 (12 Cores, 1.5 GHz) |
| Memory | Up to 512GB DDR4 ECC, 4 slots |
| Storage | 2 x 2.5" SATA/SAS hot-swap bays, 2 x M.2 NVMe |
| Networking | 2 x 10GbE RJ45, 2 x 1GbE RJ45, 1 x IPMI dedicated |
| Expansion Slots | 1 x PCIe 3.0 x16, 1 x PCIe 3.0 x8 |
| Operating System Support | Windows Server, Linux distributions, VMware |
| Main Functions | Data processing, virtualization, storage, network services |
| Maintenance and Cleaning | Clean with compressed air; avoid liquids; replace fans if noisy |
| Safety | Operate in well-ventilated area; grounded outlet; avoid blocking vents |
| Spare Parts and Repairability | Hot-swap drives, redundant PSU, replaceable fans and memory |
| General Information | Supports IPMI 2.0 remote management; includes SuperDoctor 5 health monitoring |
Frequently Asked Questions - SuperServer E403-9D-12C-FN13TP Supermicro
How do I access the IPMI interface for remote management?
Connect the dedicated IPMI LAN port to your network. By default, DHCP is enabled. Find the IP address via your router's DHCP list or use the Supervisor utility. Access via web browser at that IP. Default credentials are ADMIN/ADMIN.
What type of memory is compatible?
This server supports DDR4 ECC RDIMM and LRDIMM modules. Use 2400/2666 MHz speeds. Maximum capacity is 512 GB across 4 slots.
How can I reset the BIOS to factory defaults?
Power off the server. Remove the power cord. Locate the CMOS clear jumper (JBT1) on the motherboard. Short pins 2-3 for at least 5 seconds. Replace the jumper to pins 1-2. Reconnect power and boot.
Can I install a non-Supermicro hard drive?
Yes, the server supports standard SATA and SAS drives in the hot-swap bays. For SAS drives, ensure you have a compatible SAS controller. NVMe drives are supported via M.2 slots.
How do I update the firmware?
Download the latest firmware (BIOS, BMC, etc.) from the Supermicro support site. Use the IPMI web interface or the SUM (Supermicro Update Manager) tool. Follow the included instructions.
What does the LED blinking pattern mean?
Refer to the manual's LED indicator section. Generally: solid green = normal, blinking green = activity, solid amber = warning (e.g., fan failure), blinking amber = critical error.
Is this server compatible with VMware ESXi?
Yes, the Supermicro E403-9D-12C-FN13TP is listed on the VMware HCL. Install ESXi 6.7 or later. Use the latest drivers from Supermicro for networking and storage.
How to configure RAID?
This server typically uses a software RAID or an optional hardware RAID controller. Enter the BIOS RAID configuration by pressing Ctrl+R or Ctrl+I during boot. Alternatively, use the IPMI storage settings.
What is the recommended ambient temperature range?
Operate between 10°C to 35°C (50°F to 95°F). Ensure proper airflow with at least 1U clearance above and below the chassis for ventilation.
How do I replace a failed power supply?
The power supplies are hot-swappable. Unplug the AC cord from the failed PSU. Press the latch and pull the module out. Insert a new 800W Platinum PSU until it clicks. Reconnect the cord.
User questions about SuperServer E403-9D-12C-FN13TP Supermicro
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual SuperServer E403-9D-12C-FN13TP - Supermicro and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SuperServer E403-9D-12C-FN13TP by Supermicro.