JC-508 - Lawn mower Joycare - Free user manual and instructions

Product type	Hair clipper
Brand	Joycare
Model	JC-508
Power supply	220-240V ~ 50 Hz
Power	10 W
Blade type	Stainless steel
Cutting adjustment	Continuous lever from 1 mm to 2.4 mm
Cutting guides	4 guides (3, 6, 9, 12 mm)
Included accessories	Hair set (comb and scissors), maintenance set (brush and oil)
Recommended usage time	Maximum 8 consecutive minutes, then 10 minutes of cooling
Use	Against the grain, without forcing
Safety	Do not use near water, unplug after use, child supervision
Cleaning	With brush, oil blades, do not immerse
Operating conditions	Temperature 10-40°C, humidity 30-75%
Electrical class	Class II
Compliance	European directives
Recycling	Do not dispose of in household waste, take to a recycling center

Frequently Asked Questions - JC-508 Joycare

How to adjust the cutting length?

Use the lever on the left side for continuous adjustment from 1 mm to 2.4 mm. Fold the lever down to increase the length. For longer cuts, use the cutting guides of 3, 6, 9 or 12 mm.

How to install a cutting guide?

Always turn off the device before attaching or removing a guide. Slide the comb into the grooves until it clicks. Make sure it is inserted properly on both sides.

What is the maximum usage time?

Do not use the clipper for more than 8 consecutive minutes. For prolonged use, let the device cool down for about 10 minutes before resuming.

How to maintain the blades?

After each use, remove hair with the provided brush. Oil the blades regularly: unscrew the head, apply a drop of oil, then run for a few seconds to lubricate well.

Can I use the clipper in the shower?

No, never use the device near water (bathtub, sink, etc.). Do not immerse. Always unplug after use in a bathroom.

What to do if the blades are misaligned?

Slightly loosen the fixing screws, align the blade teeth by positioning the top blade about 1.2 mm lower than the bottom one, then retighten.

How to clean the clipper?

Unplug the device. Clean the exterior with a slightly damp soft cloth. Remove the guide and brush the blades. Never use solvents or abrasive products.

What accessories are included?

The clipper comes with 4 cutting guides (3,6,9,12 mm), a hair set (comb and scissors) and a maintenance set (brush and oil).

Can I cut wet hair?

It is recommended to use the clipper on dry hair for best results. For curly or long hair, comb against the grain before cutting.

How to store the clipper?

After use, turn off and unplug. Put the protective cap back on the blades. Store it in a dry place, away from heat sources. Do not wrap the cord around the device.

USER MANUAL JC-508 Joycare

Black-and-white photo of a pair of scissors and a comb (no text or symbols visible)

Mechanical diagram showing a lever mechanism with motion arrows (no text or symbols)

Thanks you for having purchased JOYCARE hair clipper.

Please, before starting using this appliance, read carefully the following instruction manual.

SAFETY WARNINGS

This appliance may be used by

children of more than 8 years of age, persons with physical, sensory or mental capabilities or inexpert persons only if they have been previously trained in using it in a safe manner, and only if they have been informed of the dangers the product can cause. Children may not play with the appliance. Children may not clean or carry out any maintenance on the appliance without adult supervision.

If you use the appliance in a bathroom, pull the plug out of the socket after use, because the presence of water is dangerous even when the appliance is switched off.

WARNING: do not use this

appliance near baths, washbasins or other containers full of water!

If the supply cord is damaged, it must be changed by manufacturer or by its service agent or by a qualified person in order to avoid an hazard.

GENERAL SAFETY INSTRUCTIONS

It is advisable to save these instructions for a future use.

Before connecting the appliance to the mains, please check if the voltage of your DC socket corresponds to the one stating in the rating label.

Never use the product in the bathroom or in other wet places.

In order to avoid electric shocks, it is advisable not to submerge the product into water or into other substances; if the product should accidentally fall into water, NEVER try to reach it and unplug immediately the product.

NEVER use the appliance if you are in direct contact with water: inside the bath, with water running in the basin or with wet hands.

Always keep the appliance and its accessories away from heating sources. When you store the product, it is advisable not to wind the cord round the appliance.

Never try to unplug the product pulling it from the cable or from the product itself.

In case of damages to the cable or to the product, it is necessary to stop immediately using the product and address to authorised centres.

Never try to repair the product by yourself.

In case the appliance needs to be repaired, it is necessary to address to specialised and authorised centres, otherwise the warranty will expire.

In order to avoid the product from possible overheating, it is advisable to unwind completely the cable and not to keep the product turned off it is not in use.

Never put the appliance, once turned on, under blankets or cushions.

OIL BOTTLE

Keep out of reach of children. Do not swallow. Do not apply to eyes. Dispose of properly when empty.

COMPONENT PARTS

ACCESSORIES

3 mm 6 mm

9 mm 12 mm

Black-and-white photo of a pair of scissors and a comb (no text or symbols visible)

1. On/off switch

2. Trim length adjustment lever (from 1 to 2.4mm)

3. Blades

ACCESSORIES:

4 cutting guides: 3 mm-6 mm-9 mm-12 mm

Hairdressing set (comb and scissors)

Cleaning and maintenance set (brush and oil)

INSTRUCTIONS FOR CORRECT USE OF THE PRODUCT

Remove the protective cap before switching on the device. Adjust the lever to select the desired trim length, or use one of the cutting guides provided.

Insert the plug in an electric socket and turn on the device by means of the on/off switch.

Important: Always move the hair cutters in the opposite direction to the hair growth. Position the device close to the nape of the neck and move it slowly over the hair, only cutting a few strands at a time.

Note: To achieve a uniform trim, the cutting guide should slide smoothly through the hair. Do not force it in an attempt to speed up the operation. If

this is your first experience of cutting hair, use the largest comb accessory. Avoid using the product for more than 8 minutes at a time. If you need to use it for longer, allow the device to cool down for about 10 minutes before recommencing use.

After every use, turn off the switch and remove the plug from the electric socket.

TRIM LENGTH ADJUSTMENT LEVER

Mechanical diagram showing a lever mechanism with motion arrows (no text or symbols)

The lever is conveniently positioned on the left side of the device, so that it can be moved by the thumb of the right hand while you are holding the clippers. By moving the lever up and down, you can control the depth of the trim. So, when the lever is in the highest position, the resulting trim will be shorter, and in the lowest position it will be longer.

The length of the cut ranges between a minimum of 1mm and a maximum of 2.4mm.

In addition, you are advised to use this lever to remove any hair that remains caught between the two blades. By moving the lever up and down rapidly while the machine is still switched on, you can clean the blades completely without needing to remove them.

CUTTING GUIDES

By use of the 4 cutting guides provided, you can adjust the length of the trim up to a maximum of 12 mm (with the guide comb inserted).

The cutting lengths are as follows:

Without a guide comb: 1 mm to 2.4 mm

With guide combs: from 3 - 6 - 9 - 12 mm. The length of the cut is shown on the guide comb.

IMPORTANT: The device must always be turned off when inserting or removing a cutting guide.

HOW TO CUT HAIR USING THE CUTTING GUIDES

Ease the comb into the grooves on the device until you hear a click.

Check that the comb is correctly inserted in the grooves on both sides.

Select the desired setting for the length of cut (3/6/9/12 mm).

It is advisable to start with the maximum length in order to familiarise yourself with the device.

Check that the flat side of the comb is always in contact with the scalp, in order to obtain the best possible cut.

Move the clippers slowly over the crown of the head, proceeding in different directions in order to achieve a uniform cut.

Make repeated passes over the head to ensure that the clippers cut all the hair. Comb the hair every so often in the direction of growth, to allow the clippers to grasp the hair more easily.

In order to obtain a good result with curly, thinning, long or fine hair, make use of a comb to guide the hair towards the device.

We advise you to eliminate hair from the device at frequent intervals.

ALIGNMENT OF THE BLADES

The hair clippers are put on sale ready for use and with the blades already aligned and lubricated. If the blades are not aligned correctly, they must be re-aligned in the following manner:

Slightly loosen the holding screws, and ensure that the teeth of the two blades are matching. Position those of the upper blade about 1.2 mm higher than those of the lower blade (as shown in the diagram), then re-tighten the screws.

TECHNICAL FEATURES

Power supply: 220-240V \~ 50 Hz

Wattage: 10 W

Stainless steel blades

4 cutting guides

Cleaning and maintenance set

Hairdressing set

Operation use conditions: Room temperature: from 10°C to 40°C.

Relative humidity: from 30% to 75% without condensation. Pressure: from 700 – 1060 hPa.

Environmental transportation and storage conditions: Temperature: from 10 to 40°C. Humidity: from 5 to 95%. Pressure: from 700 – 1060 hPa.

CLEANING AND MAINTENANCE

• Before starting cleaning the appliance, always unplug the appliance.
• Never immerse the appliance in water.
• Clean the unit with a damp and soft cloth.

• After having used the appliance remove the comb and using the cleaning brush clean the body of the device, in order to remove any hair from the cutting blade.

• Never use detergents and solvents to clean the appliance.

• In order to grant a long and good performance to the appliance, it is advisable to oil often the appliance. Unscrew the cutting unit, apply on oil drop and then allow the machine to run for several seconds so that the unit can lubricate properly.
• Fit the protective cap after use; keep the device only with the fitted protective cap.

SYMBOLS

appliance complies with all applicable European Directives.

DISPOSAL

The device (including its removable parts and accessories) must not be disposed of together with municipal waste at the end of its life, but in compliance with European Directive. Since it must be handled separately from household waste, either carry it to a separately-collected waste disposal centre for electrical and electronic appliances or give it back to the retailer on purchasing a new device with the same purpose. Any infringement will be severely prosecuted.

All the instructions and drawings are based on the latest information available at the time of going to print and may be subject to change.

F

MANUEL D'INSTRUCTIONS

Mechanical diagram showing a lever mechanism with motion arrows (no text or symbols)

Black-and-white photo of a pair of scissors and a comb (no text or symbols visible)

Mechanical diagram showing a lever mechanism with motion arrows (no text or symbols)

Black-and-white photo of a pair of scissors and a comb (no text or symbols visible)

Mechanical diagram showing a lever mechanism with motion arrows (no text or symbols)

MANUAL DE INSTRUÇÕES

Black-and-white photo of a pair of hair tools: a comb and a pair of scissors (no text or symbols visible)

Mechanical diagram showing a lever mechanism with motion arrows (no text or symbols)

MANUAL DE INSTRUCTIUNI

Mechanical diagram showing a lever mechanism with motion arrows (no text or symbols)

Black-and-white photo of a pair of scissors and a comb (no text or symbols visible)

Mechanical diagram showing a lever mechanism with motion arrows (no text or symbols)

Mechanical diagram showing a lever mechanism with motion arrows (no text or symbols)

Mechanical diagram showing a lever mechanism with motion arrows (no text or symbols)