AR7754W - Inverter APC - Free user manual and instructions
Find the device manual for free AR7754W APC in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type de produit | Onduleur (UPS) |
| Marque | APC |
| Modèle | AR7754W |
| Topologie | Line-interactive |
| Puissance apparente (VA) | 1500 VA |
| Puissance active (Watts) | 1000 W |
| Forme d'onde | Sinusoïdale pure |
| Tension d'entrée | 230 V AC |
| Tension de sortie | 230 V AC ± 5% |
| Fréquence | 50/60 Hz (auto-détection) |
| Nombre de prises | 8 (sur batterie + parasurtenseur) |
| Type de batterie | Plomb-acide scellée, sans entretien |
| Autonomie typique (50% charge) | ~15 minutes |
| Temps de recharge | 3 heures (jusqu'à 90%) |
| Dimensions (L x P x H) | 432 x 350 x 85 mm (2U rack) |
| Poids | 12 kg |
| Indice de protection | IP20 |
| Interface de communication | USB, RS-232, SmartSlot |
| Logiciel de gestion | PowerChute (compatible) |
| Niveau sonore | 40 dBA |
| Température de fonctionnement | 0 à 40 °C |
| Entretien et nettoyage | Dépoussiérer avec un chiffon sec ; ne pas utiliser de liquides. |
| Sécurité | Protection contre les surtensions, les sous-tensions et les courts-circuits. |
| Pièces détachées et réparabilité | Batterie remplaçable par l'utilisateur ; autres réparations par un technicien agréé. |
Frequently Asked Questions - AR7754W APC
How do I perform the initial setup of the APC AR7754W?
Connect the UPS to a grounded wall outlet, plug in your equipment, and press the power button. The UPS will perform a self-test. For detailed instructions, refer to the user manual.
What is the typical battery backup time for the AR7754W?
At half load (500W), the backup time is approximately 15 minutes. At full load (1000W), it provides about 5 minutes, enough for safe shutdown.
How often should I replace the battery?
APC recommends replacing the battery every 3 to 5 years, depending on usage and environmental conditions. The UPS will indicate when replacement is needed.
Can I connect a printer or laser printer to the UPS?
It is not recommended to connect laser printers to a UPS because they draw peak power that can overload the UPS. Use a surge protector instead.
How do I replace the battery on the AR7754W?
The battery is hot-swappable. Open the front bezel, disconnect the battery connector, remove the old battery, insert the new one, and reconnect. Refer to the manual for part numbers.
What does the 'Replace Battery' light mean?
It indicates that the battery has reached end-of-life and should be replaced promptly to maintain backup protection.
How do I set up remote monitoring?
Use the USB or RS-232 connection to connect to a computer and install APC PowerChute software. For network monitoring, install a SmartSlot management card.
What voltage does the AR7754W output?
It outputs a pure sine wave at 230V AC ± 5%, suitable for sensitive electronics.
Can the UPS be mounted in a rack?
Yes, the AR7754W is designed for 2U rack mounting. It includes rack ear brackets and supports 19-inch racks.
How do I silence the alarm?
Press the alarm silence button on the front panel. This will mute the audible alarm until the next power event.
User questions about AR7754W APC
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Inverter in PDF format for free! Find your manual AR7754W - APC and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. AR7754W by APC.