01989 - Power bank Vimar - Free user manual and instructions

Product Type	Power Supply Unit for BUS Systems
Brand	Vimar
Model	01989
Input Voltage	120-230 V~ 50-60 Hz
Input Consumption	700 mA at 120 V, 450 mA at 230 V
Output Voltage (BUS)	29 V DC (SELV) with decoupling coil
Output Voltage (AUX)	29 V DC (SELV)
Total Output Current	1280 mA (BUS + AUX)
Dissipated Power	9 W
Operating Temperature	-5 °C to +45 °C (indoor)
Installation	DIN rail (EN 60715 TH35)
Dimensions (Width)	140 mm (8 modules x 17.5 mm)
Dimensions (Height)	Approx. 90 mm (standard DIN module)
Dimensions (Depth)	Approx. 60 mm
Weight	Approx. 200 g
Protection Features	Decoupling coil, SELV, requires external bipolar circuit breaker (min 3 mm gap)
Standards Compliance	LV directive, EMC directive, EN 60065, EN 61000-6-3, EN 50130-4, EN 50491, FCC Part 15 Class B
Marine Compliance	IEC 60068-2-52 (salt mist), IEC 60068-2-6 (vibration)
Environmental	WEEE compliant, no water exposure
Maintenance	No user-serviceable parts

Frequently Asked Questions - 01989 Vimar

What are the input voltage requirements?

The input voltage is 120-230 V~ 50-60 Hz.

What is the output voltage and current?

Output voltage is 29 V DC (SELV) for both BUS and AUX, with a total output current of 1280 mA (BUS + AUX).

Can this power supply be used in marine environments?

Yes, it has been tested to IEC 60068-2-52 (salt mist) and IEC 60068-2-6 (vibration) for marine use.

How many modules does it occupy on a DIN rail?

It occupies 8 modules of 17.5 mm, totaling 140 mm in width.

What are the installation requirements?

Installation must be by qualified personnel. Ensure sufficient ventilation, no water exposure, and install a bipolar circuit breaker with a contact gap of at least 3 mm above the power supply.

Does it comply with FCC regulations?

Yes, it complies with FCC Part 15 Class B limits and is subject to the conditions that it does not cause harmful interference and accepts any interference received.

What is the dissipated power?

The dissipated power is 9 W.

What is the operating temperature range?

The operating temperature range is -5 °C to +45 °C (indoor).

Can multiple power units be installed on the same line?

Yes, up to 2 power units can be installed on each line.

What standards does it meet?

It meets LV directive, EMC directive, EN 60065, EN 61000-6-3, EN 50130-4, EN 50491, and FCC Part 15 Class B.

USER MANUAL 01989 Vimar

Power unit with output 29 V d.c. 1280 mA, power supply 120-230 V\~50-60 Hz, with decoupling coil, installation on DIN rail (60715 TH35), occupies 8 modules of 17.5 mm. For nautical scope.

Power unit with decoupling coil.

At most 2 power units can be installed on each line.

CHARACTERISTICS.

• Power: 120-230 V\~ 50-60 Hz
- Consumption:
- 120 V: 700 mA
- 230 V: 450 mA
• Dissipated power: 9 W
- BUS output voltage: 29 V d.c. (SELV) with decoupling coil
• AUX output voltage: 29 V d.c. (SELV)
• Total max output current: 1280 mA ( I_HUS + I_ALX )
- Operating temperature: -5 °C - +45 °C (from inside)
- 8 modules of 17.5 mm only installation on DIN rail (60715 TH35)

INSTALLATION RULES.

Installation should be carried out by qualified personnel in compliance with the current regulations regarding the installation of electrical equipment in the country where the products are installed.

Ensure clearance around the appliance so there is sufficient ventilation.

There must be no dripping or splashes of water on the appliance.

WARNING: To prevent injury, the appliance must be secured to the wall as described in the installation instructions.

Above the power supply there must be a bipolar circuit breaker that is easily accessible with a contact gap of at least 3 mm.

CONFORMITY TO STANDARDS.

LV directive.

EMC directive.

Standards EN 60065, EN 61000-6-3, EN 50130-4, EN 50491.

For MARINE use, this device has been submitted to the following tests: IEC 60068-2-52 - Test Kb: Salt mist, cyclic (sodium, chloride solution), IEC 60068-2-6 - Test Fc: Vibration (sinusoidal)

This device complies with part 15 of the FCC Rules (with the limits for a Class B digital device). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesidered operation.

WEEE - Information for users

If the crossed-out bin symbol appears on the equipment or packaging, this means the product must not be included with other general waste at the end of its working life. The user must take the worn product to a sorted waste center, or return it to the retailer when purchasing a new one. Products for disposal can be consigned free of charge (without any new purchase obligation) to retailers with a sales area of at least 400 m ^2 if they measure less than 25 cm. An efficient sorted waste collection for the environmentally friendly disposal of the used device, or its subsequent recycling, helps avoid the potential negative effects on the environment and people's health, and encourages the re-use and/or recycling of the construction materials.

FRONT VIEW AND CONNECTIONS.