MBF10BC - Chauffe-eau et chaudière Mirage - Free user manual and instructions
Find the device manual for free MBF10BC Mirage in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Combi Boiler (Water Heater and Central Heating) |
| Brand | Mirage |
| Model | MBF10BC |
| Dimensions (H x W x D) | 700 x 400 x 300 mm |
| Weight | 28 kg |
| Power Supply | 230 V ~ 50 Hz |
| Electrical Consumption | 150 W |
| Fuel Type | Natural Gas (G20) or LPG (G30/G31) |
| Nominal Heating Power | 24 kW |
| Nominal DHW Power | 24 kW |
| Efficiency Class | A (ErP Directive) |
| Hot Water Flow Rate (ΔT=30°C) | 11.4 L/min |
| Maximum Operating Pressure (Heating) | 3 bar |
| Maximum Operating Pressure (DHW) | 10 bar |
| Expansion Vessel Capacity | 8 L |
| Flue Type | Room-sealed (concentric 60/100 mm) |
| Protection Rating | IPX4 |
| Noise Level | < 50 dB(A) |
| Main Functions | Central heating, domestic hot water, frost protection, summer mode |
| Control Panel | Digital display, rotary knobs for temperature adjustment |
| Maintenance | Annual service required; clean primary heat exchanger and burner |
| Safety Features | Overheat protection, flame failure device, safety valve, anti-freeze thermostat |
| Spare Parts Availability | 7 years after end of production |
| Repairability Index | 8.5/10 |
Frequently Asked Questions - MBF10BC Mirage
How do I reset the boiler after a lockout?
Press and hold the reset button for 3 seconds. If the lockout persists, check for gas supply issues or call a qualified technician.
What does error code E01 mean?
E01 indicates a flame failure. Ensure gas valve is open and ignition electrodes are clean. If the problem continues, contact Mirage support.
How often should I service the MBF10BC?
An annual service by a Gas Safe registered engineer is recommended to maintain efficiency and safety.
Can I use the boiler without central heating?
Yes, you can set the boiler to summer mode using the control panel. This provides hot water only.
What is the normal water pressure for the heating system?
The recommended pressure is between 1 and 1.5 bar when cold. Below 0.5 bar may cause lockout.
Why is the hot water not reaching the set temperature?
Check if the DHW temperature setting is correct. Low gas pressure or a faulty thermistor could also be the cause. Consult the manual for troubleshooting.
How do I bleed the radiators?
Use a radiator key to open the bleed valve slightly until air escapes and water appears. Close the valve and check boiler pressure.
What type of flue does the MBF10BC require?
This model is room-sealed and requires a concentric flue system (60/100 mm). Ensure proper installation by a professional.
Is the boiler compatible with smart thermostats?
Yes, it works with most OpenTherm or on/off thermostats. Refer to the manual for compatible models.
What should I do if the boiler is leaking water?
Turn off the boiler at the mains and close the gas valve. Check for visible leaks from pipes or the pressure relief valve. Contact a technician immediately.
User questions about MBF10BC Mirage
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Chauffe-eau et chaudière in PDF format for free! Find your manual MBF10BC - Mirage and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. MBF10BC by Mirage.