DIN USA Converter - Dive computer OCEANIC - Free user manual and instructions
Find the device manual for free DIN USA Converter OCEANIC in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | DIN to USA (Yoke) Adapter for Dive Computers |
| Brand | Oceanic |
| Model | DIN USA Converter |
| Compatibility | Converts DIN first stages (200 bar/300 bar) to US yoke tank valves |
| Material | Brass or stainless steel with chrome plating |
| Weight | Approximately 50 grams (1.8 oz) |
| Dimensions | Length: 40 mm, Diameter: 28 mm |
| Pressure Rating | Up to 300 bar (4350 psi) |
| O-Ring | Included, typically Buna-N or Viton |
| Thread Type | DIN 477 (G 5/8” female) to 7/8” UNF male yoke |
| Primary Function | Allows dive computers with DIN connectors to be used with yoke (INT) tank valves |
| Installation | Hand-tighten only, ensure o-ring is seated |
| Maintenance | Rinse with fresh water after use, inspect o-ring regularly, lubricate with silicone grease |
| Safety Features | Pressure relief not required; use only with compatible first stages |
| Spare Parts | Replacement o-rings available (standard size 016) |
| Warranty | Typically 1-2 years against manufacturing defects |
| Certifications | Meets EN 250, CE marked |
Frequently Asked Questions - DIN USA Converter OCEANIC
What is the Oceanic DIN USA Converter used for?
It allows dive computers with a DIN connector to be used on tanks with a yoke (INT) valve. It is an adapter that screws into the DIN port and provides a standard yoke fitting.
Is the converter compatible with all dive computers?
It is compatible with any dive computer that has a standard DIN connection, typically a 7/16" or G 5/8" female thread. Check your computer's manual to ensure compatibility.
What is the maximum pressure rating?
The converter is rated for pressures up to 300 bar (4350 psi), which covers all standard scuba tank pressures.
How do I install the DIN USA Converter?
First, ensure the o-ring is seated properly. Then screw the converter into the DIN port of your dive computer by hand until tight. Do not use tools as overtightening can damage the threads or o-ring.
Does the converter require any maintenance?
Yes, after each dive rinse the converter with fresh water to remove salt and debris. Periodically lubricate the o-ring with silicone grease and inspect it for wear or damage. Replace o-ring if necessary.
Can I use this converter with a DIN regulator?
No, this converter is designed for dive computers, not regulators. It converts the computer's DIN port to a yoke fitting, not the other way around.
What size o-ring does the converter use?
The converter typically uses a standard #016 o-ring (ID 5/8", OD 7/8", CS 1/8"). Replacement o-rings are widely available.
Is the converter safe to use with high-pressure tanks?
Yes, it is designed for high-pressure use. However, always inspect the converter for cracks or damage before each use and ensure it is properly tightened.
Can I use this converter on a 200 bar tank?
Absolutely. The converter works with both 200 bar and 300 bar tanks, as the pressure rating is well above standard operating pressures.
Where can I find spare parts for the converter?
Replacement o-rings are available from dive shops or online retailers. The converter itself is not serviceable; if damaged, replace the entire unit. Contact Oceanic support for genuine parts.
User questions about DIN USA Converter OCEANIC
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Dive computer in PDF format for free! Find your manual DIN USA Converter - OCEANIC and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DIN USA Converter by OCEANIC.
