ENR-010P - Video recorder ACTi - Free user manual and instructions
Find the device manual for free ENR-010P ACTi in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Network Video Recorder (NVR) |
| Brand | ACTi |
| Model | ENR-010P |
| Dimensions (W x D x H) | 300 x 200 x 44 mm |
| Weight | 2.5 kg |
| Power Supply | 100-240V AC, 50/60Hz |
| Power Consumption | 30W (typical) |
| Video Channels | Up to 16 IP cameras |
| Recording Resolution | Up to 8MP per channel |
| Compression | H.265, H.264, MJPEG |
| Storage | 2 HDD bays, up to 10TB each |
| Network Interface | 2x Gigabit Ethernet |
| PoE Ports | 8 built-in PoE (IEEE 802.3af/at) |
| Operating System | Linux embedded |
| Remote Access | Web browser, mobile app |
| Backup | USB, network |
| Alarm I/O | 4 inputs / 2 outputs |
| Cooling | 1 fan |
| Operating Temperature | 0°C to 40°C |
| Humidity | 10% to 80% non-condensing |
| Warranty | 2 years |
Frequently Asked Questions - ENR-010P ACTi
How do I set up the ACTi ENR-010P NVR?
Connect the NVR to your network via Ethernet, attach cameras to PoE ports or your switch, and power on. Use a web browser to access the NVR's IP address (default: 192.168.0.100) and complete the setup wizard.
How do I add IP cameras to the NVR?
Go to the camera management page, click 'Add Camera', and enter the camera's IP address, username, and password. For PoE cameras, they are auto-detected if connected to the NVR's PoE ports. Ensure cameras are on the same network subnet.
How do I configure recording settings?
Navigate to the recording schedule page. You can set continuous, motion-triggered, or scheduled recording. Choose the recording resolution, frame rate, and compression (H.265 recommended). Apply settings to each camera.
How can I access the NVR remotely?
Enable remote access in the network settings. Use a web browser or the ACTi mobile app. You may need to configure port forwarding on your router (default HTTP port 80, RTSP port 554) or use DDNS.
How do I update the firmware?
Download the latest firmware from ACTi's website. In the NVR's system settings, choose 'Firmware Update', upload the file, and follow the prompts. Do not power off during the update. After reboot, verify the firmware version.
How do I backup recorded footage?
Insert a USB drive into the NVR's USB port. Go to the backup menu, select the desired camera and time range, and choose 'Backup to USB'. You can also backup via network to a shared folder using NAS or FTP.
What should I do if there is no video from a camera?
Check the camera's power and network connection. Verify the camera is properly added in the NVR. Ensure the camera's IP address is reachable. Try rebooting both the camera and NVR. If using PoE, check the port status.
How do I set up motion detection?
In the camera settings, enable motion detection and draw the detection zone. Adjust sensitivity and threshold. In the NVR recording schedule, set the camera to record on motion trigger. You can also configure email alerts or push notifications.
How do I change the admin password?
Log in to the NVR web interface. Go to system settings, user management, select admin, and click 'Change Password'. Enter the current password and a new strong password. Click save. Remember to document the new password.
How do I factory reset the NVR?
Press and hold the reset button on the rear panel (a small pinhole) for 10 seconds while the NVR is powered on. The NVR will reboot with factory defaults. Alternatively, in the web interface, go to system maintenance and choose 'Factory Reset'. All settings will be erased.
User questions about ENR-010P ACTi
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Video recorder in PDF format for free! Find your manual ENR-010P - ACTi and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ENR-010P by ACTi.