DAR044XA6MDB - Freezer DANBY - Free user manual and instructions

Product Type	Freezer
Brand	Danby
Model	DAR044XA6MDB
Capacity	4.4 cu ft (approx. 125 L)
Dimensions (H x W x D)	32.5 x 21.5 x 22.5 inches (approx.)
Weight	approx. 70 lbs
Power Supply	115 V / 60 Hz
Energy Consumption	approx. 280 kWh/year (estimated)
Defrost Type	Manual defrost
Temperature Control	Adjustable thermostat
Temperature Range	-10°F to 10°F (approx.)
Shelving	Removable wire shelves
Door Type	Solid door with lock
Interior Light	No interior light
Refrigerant	R600a (approx.)
Climate Class	SN/N/ST (estimated)
Noise Level	approx. 40 dB
Installation Type	Freestanding
Maintenance	Clean condenser coils annually
Warranty	1 year parts and labor (estimated)

Frequently Asked Questions - DAR044XA6MDB DANBY

What is the capacity of the Danby DAR044XA6MDB freezer?

The Danby DAR044XA6MDB has a capacity of 4.4 cubic feet (approximately 125 liters), ideal for small households or additional storage.

Does this freezer need to be defrosted manually?

Yes, the Danby DAR044XA6MDB freezer requires manual defrosting. To defrost, remove all food, unplug the unit, and allow ice to melt. Do not use sharp tools to remove ice.

What is the temperature range of the Danby DAR044XA6MDB?

The adjustable thermostat allows you to set temperatures between approximately -10°F and 10°F, suitable for long-term frozen storage.

How do I install the Danby DAR044XA6MDB freezer?

Place the freezer on a level, sturdy surface away from heat sources. Ensure adequate ventilation (at least 3-4 inches behind and sides). Plug into a dedicated 115V outlet. Wait 2-4 hours after installation before adding food.

Is the freezer noisy?

The noise level is approximately 40 dB, similar to a quiet refrigerator. Some humming or clicking sounds are normal due to the compressor and refrigerant flow.

Can I lock the freezer door?

Yes, the Danby DAR044XA6MDB comes with a lock and key for added security. The lock is located on the door handle.

How do I clean the Danby DAR044XA6MDB?

Unplug the freezer. Remove all food and shelves. Wash interior with a mild detergent and water solution. Rinse and dry thoroughly. Clean the condenser coils every 6-12 months with a vacuum or brush.

What should I do if the freezer is not cooling?

Check that the unit is plugged in and the thermostat is set correctly. Ensure the door is sealing properly. Clean the condenser coils if dusty. If the problem persists, contact a qualified technician.

What type of refrigerant does the Danby DAR044XA6MDB use?

This freezer uses R600a (isobutane), an environmentally friendly refrigerant. It is flammable, so avoid damaging the cooling system.

Where can I find the user manual for the Danby DAR044XA6MDB?

The user manual is available for free download in PDF format on the product page or by contacting Danby customer service. Always refer to the manual for detailed instructions.

USER MANUAL DAR044XA6MDB DANBY

CONTEMPORARY CLASSIC

Compact Refrigerator

Compact Refrigerator

Owner's Manual......8 - 14

Nominal Current: 1.0 A

Importer:

Ingram Micro México, S.A. de C.V.

Joselillo 3 Int, Piso 5

Col. El Parque

Naucalpan de Juárez, Edo Méx. C.P. 53398

R.F.C. IMM9304016Z4

Important Safety Information READ AND FOLLOW ALL SAFETY INSTRUCTIONS

IMPORTANT WARNING

DANGER: Risk of child entrapment. Before throwing away an old appliance:

• Remove the door or lid.
• Leave the shelves in place so that children cannot easily climb into the appliance.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electrical current.

This appliance is equipped with a cord that has a grounding wire with a grounding plug. The power cord must be plugged into an outlet that is properly grounded. If the outlet is a standard 2-prong wall outlet, it is your responsibility to have it replaced with a properly grounded 3-prong wall outlet. The serial rating plate indicates the voltage and frequency the appliance is designed for.

WARNING - Improper use of the grounding plug can result in a risk of electric shock. Consult a qualified electrician or service agent if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.

DO NOT USE AN EXTENSION CORD

Do not connect your appliance to extension cords or together with another appliance in the same wall outlet. Do not splice the power cord. Do not under any circumstances cut or remove the third ground prong from the power cord.

If the power supply cord is damaged, it must be replaced by the manufacturer, its service agent or similar qualified person in order to avoid hazard.

SAFETY REQUIREMENTS

Ensure that component parts are replaced with like components and that servicing is done by factory authorized service personnel, to minimize the risk of possible ignition due to incorrect parts or improper service.

This appliance is not intended for use by persons (including children) whose physical, sensory or mental capabilities may be different or reduced, or who lack experience or knowledge, unless such persons receive supervision or training to operate the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

WARNING: Do not damage the refrigerant circuit.

WARNING: Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

WARNING: EXPLOSION HAZARD

Risk of fire or explosion due to puncturing refrigerant tubing. Do not use sharp objects to aid in defrost. Please handle with care. Keep flammable materials and vapors such as gasoline away from the refrigerator. Only use nonflammable cleaner.

Disposal of this appliance should be in accordance with federal and local regulations.

INSTALLATION INSTRUCTIONS

OPERATING INSTRUCTIONS

LOCATION

• Two people should be used when moving the appliance.
• Remove interior and exterior packaging prior to installation. Wipe the outside of the appliance with a soft, dry cloth and the inside with a lukewarm, wet cloth.
• Place the appliance on a floor that is strong enough to support it when it is fully loaded.
• Do not place the appliance in direct sunlight or near sources of heat, such as a stove or heater, as this can increase electrical consumption. Extreme cold ambient temperatures may also cause the appliance to perform improperly.

- Do not use the appliance near water, for example in a wet basement or near a sink.

- This appliance is intended for household use only. It is not designed for outside installation, including anywhere that is not temperature controlled (garages, porches, vehicles, etc.).

- Before connecting the appliance to a power source, let it stand upright for approximately 6 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.

- This appliance is 52.7 cm (20.8 inches) wide by 84 cm (33.1 inches) high by 54.1 cm (21.3 inches) deep. Make sure that you leave the minimum amount of space between the appliance and all surrounding walls and vents.

- Allow 12.7 cm (5 inches) of space between the back, sides and top of the appliance and all adjacent walls.

- This appliance is intended for free-standing installation only and is not intended to be built into a cabinet or counter. Building in this appliance can cause it to malfunction.

FEATURES

1. Thermostat Dial: Temperature can be adjusted by turning the thermostat dial on the inner ceiling of the appliance.
2. Glass Shelves
3. Defrost Water Outlet: Ice that forms inside the appliance will automatically thaw and drain through this outlet.
4. Fruit and Vegetable Crisper
5. Leveling Leg: Adjust so the unit is level.
6. CANSTOR™ Door Liner: Holds 355ml cans of pop, juice, or beer.
7. Bottle Rack: For tall, small and medium cans or jars.
8. Magnetic Gasket: Tight fitting door seal keeps all the cooling power locked inside.
9. Interior Light (not pictured)

OPERATING INSTRUCTIONS

THERMOSTAT DIAL AND INTERIOR LIGHT

The thermostat dial and interior light housing are located on the inner ceiling of the appliance.

TEMPERATURE SELECTION

The temperature of the appliance can be adjusted by turning the thermostat dial on the ceiling of the cabinet.

• The larger, darker dots indicate the coldest setting.
• The smaller, lighter dots indicate the warmest setting.
• The "OFF" position will turn off the cooling function.

Internal temperature of the appliance can vary based on ambient temperature, the quantity of items stored and how frequently the door is opened.

INTERIOR LIGHT

The interior LED light will turn on when the door of the appliance is opened and will turn off when the door is closed.

If the interior light burns out, contact a Danby certified service technician to have it replaced.

Note: The functionality of the appliance is not affected if the light has burned out.

LEVELING INSTRUCTIONS

There is an adjustable leg on the bottom of the appliance that can be turned up or down to ensure that the appliance is level.

1. Turn the leveling leg counter-clockwise as far as it will go, until the top of the foot is touching the bottom of the chassis.
2. Slowly turn the leveling leg clockwise until the appliance is level.

OPERATING INSTRUCTIONS

DOOR REVERSAL INSTRUCTIONS

If the appliance is placed on its back or side for any length of time during this process, it must be allowed to remain upright for 6 hours before plugging it in to avoid damage to the internal components.

1. Remove the three screws from the back of the worktop, lift the back of the worktop and pull it toward the front of the appliance to remove it. Remove the worktop hinge hole cover from the left side of the worktop and move it to the hinge hole on the right side of the worktop. See figure 1.
2. Remove the screw from the door spindle cover and remove the upper right hinge and door from the chassis. Remove the door spindle from the upper right hinge. See figure 2.
3. Remove the lower hinge hole cover from the bottom left side of the door and move it to the bottom right side of the door. See figure 3.
4. Remove the adjustable foot and the two screws holding the bottom hinge. Move the bottom hinge to the left side of the chassis and install with the screws. Install the adjustable foot on the left side of the appliance and move the solid foot to the right side of the appliance. See figure 4.
5. The upper left hinge is in the accessory bag inside the appliance. Install the door spindle on the upper left hinge. Install the upper left hinge and door onto the chassis. Install the door spindle cover with a screw. Reinstall the worktop by laying it on top of the appliance and pushing it toward the back until it clicks into place and then reinstall the three screws at the back. See figure 5.

Note: When reinstalling the door, ensure that the top of the door is level with the top of the chassis and that the rubber gasket makes a good seal with the chassis all the way around.

A. Worktop Hinge Hole Cover B. Worktop C. Door Hinge Hole Cover D. Door Spindle Cover E. Door Spindle

CARE & MAINTENANCE

CLEANING

Ensure the appliance is unplugged before cleaning.

• To clean the inside of the appliance, use a soft cloth and a solution of a tablespoon of baking soda to one quart of water or a mild soap solution or some mild detergent.
• Wash removable shelves in a mild detergent solution, then dry and wipe with a soft cloth.
• Clean the outside with a soft, damp cloth and some mild detergent.
• It is important to keep the area clean where the door seals against the cabinet. Clean this area with a soapy cloth. Rinse with a damp cloth and let dry.

Note: Do not use cleaners containing ammonia or alcohol on the appliance. Ammonia or alcohol can damage the appearance of the appliance. Never use any commercial or abrasive cleaners or sharp objects on any part of the appliance.

POWER FAILURE

Most power failures are corrected within a few hours and should not affect the temperature of your appliance if you minimize the number of times the door is opened. If the power is going to be off for a longer period of time, take the proper steps to protect your contents.

Note: Wait 3 to 5 minutes before attempting to restart the refrigerator if operation has been interrupted.

DEFROST

This appliance is equipped with an automatic defrost function and does not require manual defrosting. Defrost water from the appliance is channeled into a drip tray located above the compressor. Heat transfer from the compressor causes the defrost water to evaporate.

VACATION

• Short vacations: Leave the appliance operating during vacations of less than three weeks.
• Long vacations: If the appliance will not be used for several months, remove all items and turn off the appliance. Clean and dry the interior thoroughly. To prevent odor and mold growth, leave the door open slightly, blocking it open if necessary.

MOVING

• Remove all items.
• Securely tape down all loose items (shelves) inside your appliance.
• Turn the adjustable leg up to the base to avoid damage.
• Tape the door shut.
• Be sure the appliance stays secure in the upright position during transportation. Also protect the outside of the appliance with a blanket or similar item.
• If the appliance is placed on its back or side during transportation, upon reaching the destination, allow it to remain upright for 6 hours before plugging in to allow the coolant to settle.

DISPOSAL

This appliance may not be treated as regular household waste, it should be taken to the appropriate waste collection point for recycling of electrical components. For information on local waste collection points, contact your local waste removal agency or government office.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE
No power • A fuse may be blown or the circuit breaker	trippedPlug not fully inserted into the wall outlet
Internal temperature not cold enough • Temperature setting is too warmDoor is not shut properly or opened excessivelyRecently added a large quantity of warm food to the cabinetClose proximity to heat source or direct sunlightAmbient temperature or humidity is very high
Appliance runs continuously • Temperature setting is too coldDoor not shut properly or opened excessivelyRecently added a large quantity of warm food to the cabinetClose proximity to heat source or direct sunlightAmbient temperature or humidity is very high

Guarantee Policy

INGRAM MICRO MEXICO, S.A. Of C.V. at Joselillo No. 3, 5th floor Col. El Parque, Naucalpan de Juárez Municipality, State of Mexico, CP 53398. Tel. [phone] Guarantee the product described below for the term of 1 year (one year) counted from the moment of purchase against any malfunction or defect in their materials, parts or components. The labor and transportation costs of the product that are within its service network are included.

The company agrees to exchange the defective product for a similar one with previous diagnosis made by our service center. The response time will not be more than 30 (thirty) calendar days from the date of receipt of the product.

To make the guarantee effective, you must present the properly sealed policy or the corresponding invoice or receipt and the product and its accessories included to the establishment where you purchased it; Or at the following address: Joselillo No. 3, 5th floor Col. El Parque, Naucalpan de Juárez Municipality, State of Mexico, C. P. 53398. Parts, components and accessories may be obtained at the same location.

This warranty will override any other warranty offered by the manufacturer or distributor.

1. Repair or replacement of the product and workmanship, including transportation costs of the product, will be free of charge to you within the warranty period.
2. You may purchase parts, components, consumables and accessories at the facility where you purchased your product or at the addresses listed above.

Exceptions:

a) When the product had been used in abnormal conditions. b) When the product has not been operated in accordance with the owner's manual. c) When the product has been altered or repaired by persons not authorized by INGRAM MICRO MEXICO, S.A. From C.V.

Brand:Model:Dealer name:Dealer address:Dealer telephone number:

Stamp and date

Modelo • Model

DAR044XA6MDB • DAR044XA6PDB

DAR044XA6LDB • DAR044XA6DDB

DAR044XA6BSLDB