EWT1212 - Washing machine ELECTROLUX - Free user manual and instructions

Product Type	Top-loading washing machine
Brand	Electrolux
Model	EWT1212
Maximum Capacity	12 kg
Wash Programs	Regular, Fast, Colours, Delicates, Heavy Soil, Woollens, Handwash, Bedding, Rinse+Spin, Drain+Spin, Tub Cleaning, Favourite
Stain Wand	Yes, with ultrasound technology
Water Level Options	Auto, High, Extra-Medium, Medium, Low, Extra-Low
Dirt Level Options	High, Regular, Light & Fast
Rinse Options	Fast, Eco, Deep, Extra
Soak Time Option	Yes, adjustable
Delay End	2, 4, 6, 8 hours
Display	Digital with time remaining, error codes, and status
Lid Soft Landing	Yes
Lid Lock	Yes, during spin
Detergent Dispenser	Adjustable flap for powder or liquid detergent
Fabric Softener Dispenser	In agitator cup, 75 ml capacity
Bleach Dispenser	Through hole in top panel
Lint Filter	Yes, in center of agitator
Power Supply	220-240 V, 50 Hz
Stain Wand Auto Shut-off	After 5 minutes of continuous use
Safety Features	Child safety, lid lock, over-suds protection

Frequently Asked Questions - EWT1212 ELECTROLUX

How do I activate the Stain Wand?

Close the lid, then press and hold the ▶ and Delay End buttons simultaneously for 3 seconds until the WATER and ON buttons light up.

What should I do if the machine shows an E17 error?

This indicates an out of balance condition. Open the lid, redistribute the clothes evenly around the agitator, then close the lid. The machine will continue the spin.

Can I use liquid detergent?

Yes. Adjust the flap in the detergent compartment to the down position for liquid detergent. For powder, keep the flap up.

How do I clean the lint filter?

Remove the filter column from the center of the agitator, unclip the bag, turn it inside out, remove lint, wash with hot water, and reassemble.

What type of detergent should I use?

Use a low-sudsing detergent designed for washing machines. Avoid soap-based products. Follow the manufacturer's dosage instructions.

How can I reduce the washing time?

Press the Reduce Time button, then use the ◀ and ▶ buttons to decrease the agitation time. This option is available before starting the program.

What does the 'PR' display mean?

It indicates a power failure recovery. The machine will resume the wash from where it stopped if no settings are changed within 5 seconds.

Can I open the lid during a spin cycle?

No, the lid is locked during spin. To access the bowl, press and hold the Start/Hold To Pause button for 1.2 seconds to pause. Wait for the bowl to stop before opening.

How do I enable or disable the end-of-wash beeping?

From stand-by or pause mode, press and hold the Start/Hold To Pause button for 3 seconds. Use ◀ or ▶ to select BP:ON (enabled) or BP:OF (disabled), then press Start/Hold To Pause to store.

What should I do if the machine does not fill with water?

Check that the water taps are turned on and the inlet hose filters are clean. Also ensure the drain hose is not blocked. If the problem persists, call service.

USER MANUAL EWT1212 ELECTROLUX

We were thinking of you

when we made this product

WELCOME TO THE WORLD OF ELECTROLUX

Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable. You find some examples on the cover in this manual. Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine. We promise that it will provide a superior User Experience delivering Ease-of-Mind. Good luck!

The symbols you will see on some paragraphs of this booklet have the following meaning:

The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly important for your safety or correct functioning of the appliance.

The information marked with this symbol provides additional instructions and practical tips on the use of the appliance.

Tips and information about economical and ecological use of the machine are marked with this symbol.

CONTENTS

Safety information 4

Product description 6

Out of Balance Interruption.... 8

Control panel 9

Use 10

Washing hints 20

Washing program.... 22

Care and cleaning 23

Helpful hints in dealing with washing

problems.... 25

Troubleshooting.... 26

Troubleshooting fault displays.... 28

Environment concerns 30

SAFETY INFORMATION

In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings.

To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features.

Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety.

General safety

• It is dangerous to alter the specifications or attempt to modify this product in anyway.
• Make sure that small pets do not climb into the washbowl. To avoid this, please check into the washbowl before using the appliance.
• Any objects such as coins, safety pins, nails, screws, stones or any other hard, sharp material can cause extensive damage and must not be placed into the machine.
• Only use the advised quantities of fabric softener and detergent. Damage to the fabric can ensue if you overfill. Refer to the manufacturer's recommendations of quantities.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Wash small items such as socks, laces, washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the agitator.
• Do not use your washing machine to wash articles with whale bones, material without hems or torn material.
• Always unplug the appliance and turn off the water supply after use, clean and maintenance.
• Under no circumstances should you attempt to repair the machine yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local Service Centre. Always insist on genuine spare parts.

Installation

• This appliance is heavy. Care should be taken when moving it.
• When unpacking the appliance, check that it is not damaged. If in doubt, do not use it and contact the Service Centre.
• After having installed the appliance, check that it is not standing on the inlet and drain hose.
• If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely.
• Always be sure, that there is no water leakage from hoses and their connections after the installation.
• Any plumbing work required to install this appliance should be carried out by a qualified plumber.
• Any electrical work required to install this appliance should be carried out by a qualified electrician.

Use

• This appliance is designed for domestic use. It must not be used for purposes other than those for which it was designed.
• Only wash fabrics which are designed to be machine washed. Follow the instructions on each garment label.
• Do not overload the appliance. See the relevant section in the user manual.
• Before washing, ensure that all pockets are empty and buttons and zips are fastened. Avoid washing frayed or torn articles and treat stains such as paint, ink, rust, and grass before washing. Underwired bras must NOT be machine washed.
• Garments which have been in contact with volatile petroleum products should not be machine washed. If volatile cleaning fluids are used, care should be taken to ensure that the fluid is removed from the garment before placing in the machine.
• Never pull the power supply cable to remove the plug from the socket; always take hold of the plug itself.
• Never use the washing machine if the power supply cable, the control panel, the working surface or the base are damaged so that the inside of the washing machine is accessible.
• Risk of burns. Do not use Stain Wand directly on hands, face, eyes, or any other part of the body. NEVER USE STAIN WAND ON GARMENTS THAT ARE DRESSING OR COVERING THE BODY. (*)
• The temperature of Stain Wand's tip may rise up during its operation. DO NOT TOUCH THE TIP during operation. (*)
• In case the temperature rises too much, stop using the device immediately and wait until it cools down before resuming operation. (*)
• Do not use Stain Wand without wetting the stain. (*)
• Never use Stain Wand on flammable solvents (alcohol, thinner, gasoline, etc...). (*)
• Never use Stain Wand on animals, pets. (*)
• Keep Stain Wand away from children. (*)
• Stop using the Stain Wand immediately if any physical discomfort occurs. The use of Stain Wand is not recommended for people with pacemaker. (*)
• Do not pour water directly on the Stain Wand and never immerse it in water or you may risk damaging the device. (*)

(*) Safety information for Stain Wand.

Child safety

• This washing machine is not intended for use by young children or infirm persons without supervision.
• Young children should be supervised to ensure that they do not play with the appliance.

- The packaging components (e.g. plastic film, polystyrene) can be dangerous to children - danger of suffocation! Keep them out of children's reach.

- Keep all detergents in a safe place out of children's reach. - Make sure that children or pets do not climb into the washbowl.

PRODUCT DESCRIPTION

1 Stain Wand 2 Control Panel 3 Safety Glass 4 Lid 5 Front Feet 6 On/Off Switch 7 Water Inlet Hose 8 Main Cable 9 Drain Hose 10 Back Feet 11 Fabric Softener Dispenser 12 Lint Filter 13 Wash Bowl 14 Bleach Dispenser 15 Detergent Dispenser Drawer 16 Agitator

Stain Wand - Operating Instructions

This system was especially developed to assist in the day-to-day work of removing stains from your clothing. It works with ultrasound technology combined with water that emits vibrations that help loosen the stains from fabric, turning their removal easier when washing.

To use Stain Wand, make sure both power and water is turned ON in your machine.

1. Before using Stain Wand, first verify the fabric colour integrity by running the preliminary test below:

1.1 Spray a small amount of water in a hidden area of the fabric:

1.2 Pour a small amount of colourless liquid detergent;

1.3 Apply Stain Wand (according to the instructions below) on this area;

1.4 Wait until the fabric dries out and look for any signs of fading. If the colour didn't change you may use the Stain Wand.

1. With the washing machine lid closed, push "▶" and "Delay End" buttons simultaneously for 3 seconds until "WATER" and "ON" buttons are lit. The Stain Wand is ready for use.

1. The cable has a locking position when completely pulled out. Remove the Stain

Wand from its housing and pull out cable completely and release so that it goes back and locks at its intended locking position.

1. Remove any residue left over the stain by using a small brush. Place an absorbing paper or a clean cloth under the stain (this paper or cloth will absorb the dirt). Since the washing machine lid is closed, it may be used as working area.
2. Pour two drops of colourless liquid detergent on the stain.

Add more detergent if necessary (in case of persistent stains).

1. Press the "WATER" button and direct the water spray onto the stain. Press the "WATER" button as many times as needed to wet the stain. Repeat this procedure every time the stain dries out.

For better stain removal, the stain must always remain wet when using the device.

1. Place the tip on the stain. While pressing and holding the "ON" button, gently drag the tip over the stain in circular or zig-zag movements.

You may hear a peculiar sound when the ultrasound is working; this is normal. For best results, the Stain Wand should be held vertically.

1. As the stain becomes softer, remove any excess dirt and water that remains on the fabric using an absorbent paper or a clean cloth. Change the paper/cloth under the stain whenever it becomes too wet.
2. Repeat steps 5 to 7 if necessary. Please note: Some stains cannot be removed 100%.
3. After use, return the Stain Wand to its housing by pulling the cable gently until it unlocks. As the cable retracts, place the Stain Wand back in its housing.

You can turn it off by pressing the "▶" and "Delay End" buttons simultaneously.

ATTENTION

• Do not use the Stain Wand continuously for more than 5 minutes to avoid excessive heat, and always keep the stain wet by spraying water during Stain Wand usage, which also helps to cool down the Stain Wand tip. For your safety, the Stain Wand will switch off after 5 minutes of continuous use, but you can switch it on again by pressing the "ON" button. Use colourless liquid detergent only.
• Do not use coloured detergents or softeners. The colour of detergent or softener may stain your fabrics even more.
• Clothes that carry symbols: ☑ (do not wash at all), ☑ (do not bleach), ☒ (do not iron) and ○ (dry cleaning), are not suitable for Stain Wand pretreatment.

NOTE

• Depending on water supply pressure, you may need to press the "WATER" button several times to inject water to make the stain wet enough.
• To test the Stain Wand, spray some water on the lid by pressing the "WATER" button, then operate the Stain Wand tip on it by pressing the "ON" button. If water splashes, that means the Stain Wand is functioning fine. If not, please contact Customer Service.

Out of Balance Interruption

The washing machine can stop during the spin stage of a wash because of an out of balance condition. The display will show "E17" and you will hear a short beep every minute.

Out of balance during spin is caused by an uneven distribution of clothes in the wash bowl.

To rectify the out of balance condition, open the lid and redistribute the clothes evenly in the space between the agitator and wall of the wash bowl. Closing the lid will start the machine and continue the spin stage of the wash.

If you have frequent out of balance interruptions, it may be due to your washing machine not standing firm and level on the floor. This can be corrected by adjusting the washing machine legs as described in the Installation Instructions supplied with your machine.

Power Failure Recovery

When there is a power failure while the machine is washing, rinsing, or spinning, the machine tries to save the settings at which stage the machine is doing, and then when the power returns, the machine shows "PR" on the digital display.

If the Program or any other setting is not changed within 5 seconds, then the machine starts washing from the stage where it left off.

Button Response and Lights

Always press buttons gently. Watch the lights on the control panel to see the effect pressing a button or turning a program selector knob has, and listen for 'BEEPS'.

When you press a button you will get a short 'BEEP' to acknowledge the entry. If the option is not available at the time, the machine will not allow you to select it, and you will hear a long 'BEEP' to remind you the option is not available.

After the machine has started, the entire wash option button will be disabled and the machine will show "ERR" on the display with three short beeps to indicate the button is disabled. The start button is still active, but you need to press and hold the button for 1.2 seconds to pause the machine.

This is to confirm that you really want to pause the machine. When in pause mode, all options will be able to be changed again.

All functions of the washing machine will stop when the lid is open.

Enabling/Disabling End-of-Wash Beeping Mode

This mode permits you to either enable or disable the beeping (4 beeps every 4 minutes) at the end of the wash. As an example, you might wish to disable this beeping when you start a wash when going to bed, so that when the wash finishes approximately 1 hour later, it will not disturb you through the night.

NOTE: All error beeping is not disabled by this feature, such as a critical fault, or lid open during fill/agitate/spin, or out of balance during spinning.

To change the "beeping" selection:

1. When the washing machine is in STAND-BY-MODE or PAUSE MODE, press and hold "Start/Hold To Pause" button for about 3 seconds to enter Enabling/Disabling End-Of-Wash Beeping mode.

The digital display will show "BP:ON" when the end of wash beeping is enabled (this is the default factory setting).

The digital display will show "BP:OF" when the end of wash beeping is disabled.

1. Press the "Modify Option (◀, ▶)" button to change the selection, then press the Start/Hold To Pause button to store the new selection.

NOTE: If you do not press a button within 5 seconds, the washing machine will return to the previous setting. To reprogram, simply repeat the above process.

CONTROL PANEL

1 Program Select Touchpads 2 Option Select Touchpads 3 Modify Option Touchpads 4 Reduce Time Touchpad 5 Save Favourite Touchpad

6 Delay End Touchpad 7 Display 8 Start/Hold To Pause Touchpad 9 Stain Wand Option (see page 7)

ON - OFF Switch

The On/Off switch is used to turn your washing machine on and off.

The On/Off switch is located at the back of the control panel on the left-hand side, above the rating plate.

USE

Follow the instructions in this section for best washing results.

Sort Your Washing Into Separate Wash Loads

Each load of washing should contain clothing that requires the same washing conditions. For example, you should not wash delicate clothes with very dirty work clothes.

Colour-fast and non-colour-fast fabrics should be separated. Knowing the type of fabrics you have and how dirty they are will help when you make selections from the wash program options.

Some fabrics are lint collectors and can pick up lint, dirt, and colour from other fabrics that are lint producers. Some examples are listed below:

Lint collectors

• Corduroy
• Synthetics • Permanent press fabrics

Lint producers

• Towels
• Nappies
• Chenille/Candlewick

i

Make sure that you wash lint collectors separately from lint producers.

Check your clothes to avoid damage

Empty all pockets. Close all hooks and zippers to avoid snagging clothes.

Wash bras, pantyhose and other delicates in a mesh laundry bag, which you can purchase from your supermarket.

Pre-treatment sprays and stain removers

Pre-treatment sprays and stain remover can damage plastic components on your washing machine.

If you use pre-treatment sprays or stain removers, apply them to the clothing well away from your washing machine.

Load the washing machine

When loading the clothes into your washing machine, there are four things to remember:

• Clothes must be loaded evenly around the agitator. For best results load small items first, followed by large items.
• Clothes must not be wrapped around the agitator.
• The washing machine must not be overloaded. Clothes must be able to move around during washing.
• The load should contain only three or four large items, for example, sheets. The rest of the load should be small items. A mixed load of large and small items will wash cleaner than a load of all large items.

Detergent and fabric softener use

• Don't use the wrong type of detergent. You must use a low sudsing detergent designed for washing machines.
• Don't use soap-based products in your washing machine.
• Measure the correct amount of powder or liquid detergent by following the recommendations on the package.
• It is best to use detergent labelled low sudsing. Good quality, front load detergent will perform well in this machine.
• Don't use too much detergent. This will give you too many suds causing low spin speeds, poor rinsing and overloading the motor during spin stages of the wash program.

Do not spill fabric softener on the clothes as it may stain them.

Add the detergent

When using the washing machine for the first time, check that the dispenser is set for the type of detergent you will use. To do this, proceed as follows:

1. Pull the dispenser drawer forward until it stops.
2. Lift the front of the drawer up and forward to remove it from the runners.
3. Check the position of the flap at the rear of the detergent compartment in the dispenser drawer. (Factory setting is flap up for powder.)

1. Clip the flap down if you are going to use liquid detergent.

1. Refit the dispenser back into its runners.

Remember: If you change the type of detergent you use, the position of the flap will need changing.

1. You are now ready to add detergent. Measure the amount you will use and pour it into the detergent compartment of the dispenser drawer.

When using liquid detergent, some may leak out of the dispenser into the wash load earlier than expected through small openings in the back of the dispenser. These openings are to help the flushing out of detergent.

1. If you want to use fabric softener, see "Add fabric softener".
2. Close the drawer by pushing it backwards into the top panel of the washing machine when you have finished adding detergent.

Add Fabric Softener

1. Measure the correct amount of fabric softener by following the recommendations on the package.
2. If you are going to use intensive fabric softener, mix softener with an equal amount of warm water but only mix enough to fill to the line marked inside the cup. The softener cup holds 75ml.
3. Pour the mixed softener into the cup in the top of the agitator.

Do not overfill the cup.

1. Do not spill fabric softener on the clothes as it may stain them.

IMPORTANT: If you are going to use fabric softener, you must select the DEEP rinse option, i.e. deselect the EXTRA or ECO or FAST rinse option. Also if softener is used frequently the machine must be flushed out regularly.

NOTE: You do not have to use fabric softener, your washing machine will wash the clothes perfectly well without it.

Adding Bleach

Bleaching of clothes can help to remove stains, heavy soiling and to kill bacteria.

Oxygen type - This is generally a powder type bleach. Mix the required quantity with water and pour down the hole in the top panel during the fill when there is some water in the wash bowl. Refer to the instructions on the bleach container.

Chlorine type - This type of bleach should not be mixed with detergent. Mix the bleach with water as per the instructions on the container.

To do this, proceed as follows:

1. Select the program "Regular Wash 🔍" position.
2. Press the "Start/Hold To Pause" button to commence water fill.
3. Pour the bleach solution down the hole in the top panel during fill when there is some water in the wash bowl.
4. Allow the machine to agitate for a few minutes, then let it stand for the required time by press and hold the "Start/Hold To Pause" button for 1.2 seconds to pause machine.
5. Select the "Drain + Spin 🔍" program position and press the "Start/Hold To Pause" button to empty the wash bowl.
6. You can now wash the clothes load using detergent and your selected wash program.

NOTE: Bleach should not be used on silk, wool, rayon or drip dry clothes.

Operating Your Washing Machine

Starting your washing machine

1. Turn on the taps and turn power on at the power point.
2. Press the On-Off switch button to switch ON the machine.
3. Close the lid.

The machine will show a pattern of lights. Wait for this to happen before attempting to operate the machine.

Your washing machine is now in Stand By Mode and ready to wash your clothes.

If the settings shown on the control panel are what you want to use and the PROGRAM ICON is set to the correct wash program for your clothes load, press the "Start/Hold To Pause" button to start your wash.

Lid Soft Landing Feature

When the lid is fully opened, to close just pull down initially the lid then the lid will close down slowly by itself.

The lid soft landing device will not work if the lid is opened less than 80 degrees. Please keep your hand away, as the lid will close rapidly and could crush your hand.

Select the Required Program

Press the Program icon repeatedly to choose the wash program you want. The corresponding light will illuminate.

The program selector is divided into the following sections.

• Regular Wash, Fast Wash, and Favourite.
• Colours, Delicates, Heavy Soil, Woollens, Handwash, Bedding, Rinse+Spin, Drain+Spin, and Tub Cleaning.

Once you select a wash program, the selected program will remain active for the entire wash cycle.

If you have started your wash and wish to change the program, press and hold the "Start/Hold To Pause" button for 1.2 seconds to enter Pause mode. Selecting a new program icon will reset the machine to the start of the new program.

Note: When you choose the Woollens or Bedding program, the Deep Rinse option is automatically selected. You will not be able to select Eco Rinse or Fast Rinse with these two programs.

When you select the Drain+Spin program, there will be a delay of at least 2 minutes before the washing machine starts to spin.

This delay is a pump-out (drain) period to ensure the drum is empty of water, which is necessary before spinning begins.

Even if you have only placed wet clothes into an empty drum, the delay before spinning will still occur for safety and to protect your washing machine.

Program Option Buttons

Depending on the program, different functions can be combined. These must be selected after choosing the desired program and before pressing the "Start/Hold To Pause" button.

Wash Load Option

Press the OPTIONS button ( < , > ) to select the Load icon, then press the modify option buttons ( ◀ , ▶ ) to choose the level of your load size. The machine will fill the amount of water to be used for your wash load.

You can select:

Selection	Water level description	Clothes Load
AUTO -	The exact water level required to wash your clothes effectively is determined and set for you automatically, ensuring no water is wasted.
HIGH	The machine will fill the high amount of water for your FULL load.	9-12 kg.
X-MED (Extra - Medium)	The machine will fill the extra medium amount of water for your NEARLY FULL load.	6-9 kg.
MED (Medium)	The machine will fill the medium amount of water for your HALF load.	4-6 kg.
LOW	The machine will fill the Low amount of water for your SMALL load.	2-4 kg.
X-LOW (Extra - Low)	The machine will fill the Very Low amount of water for your VERY SMALL load.	0-2 kg.

We advise you to use AUTO load level whenever you can. The AUTO load level ensures just the right amount of water is used for the wash load.

Use only the amount of water you need for the wash load.

If you want to add more water after the wash cycle has started, press and hold the "Start/Hold To Pause" button for 1.2 seconds to pause the machine and then select the new higher level that you want, press "Start/Hold To Pause" again to operate the washing machine.

The washing machine will add water up to the new level selected and continue the wash program.

Dirt Level Option

Press the OPTIONS button ( < , > ) to select the Dirt icon, then press the modify option buttons (◀ , ▶ ) to choose the dirty level to be used for your clothes.

There are 3 dirt levels to choose from:

• HIGH for heavily soiled clothes, e.g., very dirty work clothes and overalls.
• REGULAR for everyday soiled items, e.g., family clothes, sheets, etc.
• LIGHT & FAST for lightly soiled clothes, just to freshen them up.

The Dirt Level option chosen will have an influence on the wash time of the selected wash program.

For the same wash program, High Dirty Level will have a longer wash time than Regular Dirty Level, and Regular Dirty Level a longer wash time than Light & Fast Dirty Level.

Select the Soak Time Option

This option allows you to soak heavily soiled clothes at the beginning of the wash.

To do this, press the Options button (<, >) to select the Soak icon, then press the Modify Option buttons (◀, ▶) to select the soak time to be used for your wash load.

The lid must be closed to allow Soak functions to operate, including the Heavy Soil wash program 6 minute soak. At other times, the clothes are soaking.

Rinse Option

Pressing the OPTIONS button (<, >) to select the Rinse icon, then press the modify option buttons (◀, ▶) to choose the rinse type for your wash load.

For most washes the machine automatically selects "Deep" rinse for you.

There are four rinses to choose from: Fast rinse, Eco rinse, Deep rinse, and Extra rinse.

• Extra rinse: the machine fills twice, giving you two deep rinses.
• Deep rinse: the machine fills once, giving you one deep rinse.
• Eco rinse is a spray rinse giving you maximum water saving.
• Fast rinse uses less time than Eco rinse by performing only 3 Eco sprays, but the amount of water in each spray is increased.

How does Eco Rinse work?

When Eco rinse is used, rinse water is sprayed into the washbowl in pulses. After each pulse, the washbowl will spin to remove detergent-laden water from the clothes.

The machine will go through a series of maximum six pulse spray and short spin cycles in this manner, depending on program selection, followed by a final long spin that removes the water from the clothes to complete the full wash program.

• Compare this with Deep rinse, where much more water is used.
• Deep rinse: water enters the machine and fills up to the selected wash water level. The washer agitates and finally empties the rinse water through the drain hose.
• Extra rinse: this is a special option for those who suffer from allergies. This extra rinse provides two deep rinses to ensure all detergent residue has been removed.

- Eco Rinse and Fast Rinse cannot be selected with the Woollens and Bedding programs.

- Extra/Eco/Fast rinse is not designed to be used with fabric softener.

Select Deep rinse if you are going to use fabric softener.

Deep rinse ensures the fabric softener is correctly dispensed and thoroughly removed from your clothes during rinsing.

Reduce Time Option

This option allows you to reduce washing time during the washing process.

Press the 'Reduce Time' button, then use the modify option buttons ◀ to decrease or ▶ to return to the default agitation time.

Save Favourite

To recall the Favourite wash program, touch and release the Favourite button once.

On the screen, you will receive acknowledgement that the Favourite program is loaded.

You can recall a Favourite wash program ONLY when the washing machine is:

• in the program selection mode, or - at any stage of a wash program in pause mode.

Otherwise, touching Favourite will have no effect.

The first time you touch the Favourite button, a factory-set Favourite wash program will load for you. If you want to use the Favourite program shown on the display screen without making any changes, touch Start/Hold To Pause (▷II) to begin your wash.

To reprogram Favourite with your own selections and save them, proceed by putting the machine in pause mode and follow the following instructions.

• Touch the Favourite button to enter reprogramming mode. • Make desired selections on all other buttons.
• To EXIT reprogramming mode and NOT save changes, touch Start/Hold To Pause (▷II) button.

- To save the new program, touch Save Favourite once.

You can copy other programs to Favourite by touching once the program to copy followed by one touch on the Save Favourite button.

You can also copy the running program to Favourite by touching Save Favourite in pause mode.

Delay End Option

Before you start the program, this option makes it possible to define the end of the washing program by 2, 4, 6, and 8 hours.

By pressing the Delay End button, then press the modify option buttons (◀, ▶) to choose the end time as you wish.

This option must be selected after choosing the wash program, and before pressing the “Start/Hold To Pause” button.

If after having set the Delay-End option (and pressed "Start/Hold To Pause" button) and you wish to cancel or modify it, follow the below steps:

1. Set the washing machine to PAUSE by pressing and holding the "Start/Hold To Pause" button for 1.2 seconds.
2. Deselect the Delay-End option, changing the status.
3. Press the "Start/Hold To Pause" button to start the program.

Start/Hold To Pause

To start the selected program, press the "Start/Hold To Pause" button.

If you have started your wash and you wish to stop it for some reason, press the "Start/Hold To Pause" button and hold it for 1.2 seconds to enter PAUSE mode.

Lid Locked (☐)

The padlock symbol 📋 is displayed on the screen to advise you when the lid of the washing machine is locked in the closed position. The lid will be automatically locked when the washbowl is spinning during Rinse, Spin, and Drain stages.

If the lid is open and the machine is waiting for it to be closed for the wash program to continue, you will see 'LO' in the digital display accompanied by 'beeping'.

Should you need to access the washbowl during spin, press and hold the "Start/Hold To Pause ▷||" button for 1.2 seconds. You will have to wait a short time for the bowl to stop spinning before the lid unlocks and the padlock symbol 📋 in the screen disappears.

• DO NOT insert anything into the lid lock slot in the top panel of the washing machine.
• DO NOT interfere with the lid lock mechanism to try to disable it or otherwise change the way it works.
• DO NOT try to force open the lid when it is locked.

Display

The display shows the following information:

Machine In Pause Mode

You can tell when your washing machine is in PAUSE mode. The message "SP" is displayed.

Estimated time of the selected program

After selecting a program, the estimated time is displayed in hours and minutes (for example 2.05).

The estimated time is calculated automatically on the basis of the maximum recommended load for each type of fabric.

After the program has started, the time remaining is updated every minute.

End Of Program

When the program is completed, the four zeros will flash.

Alarm Codes

In the event of operating problems, some alarm codes can be displayed, for example E20 (see "Troubleshooting" and "Troubleshooting fault displays" on pages 27, 28).

Incorrect Option Selection

If an option which is not compatible with the set wash program is selected, the message "ERR" is displayed for about 2 seconds and 3 consecutive short beeps are emitted.

WASHING HINTS

Sorting The Laundry

• Follow the wash code symbols on each garment label and the manufacturer's washing instructions.
• Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens.

Before Loading The Laundry

• Never wash whites and coloureds together. Whites may lose their “whiteness” in the wash.
• New coloured items may run in the first wash; they should therefore be washed separately the first time.

Make sure that no metal objects are left in the laundry (e.g. hair clips, safety pins, pins).

• Button up pillowcases, close zip fasteners, hooks and poppers.
• Tie any belts or long tapes.
• Remove persistent stains before washing.
• Rub particularly soiled areas with a special detergent or detergent paste.
• Treat curtains with special care.
• Remove hooks or tie them up in a bag or net.

Removing Stains

Stubborn stains may not be removed by just water and detergent. It is therefore advisable to treat them prior to washing.

Blood: treat fresh stains with cold water. For dried stains, soak overnight in water with a special detergent then rub in the soap and water.

Oil based paint: moisten with benzine stain remover, lay the garment on a soft cloth and dab the stain; treat several times.

Dried grease stains: moisten with turpentine, lay the garment on a soft surface and dab the stain with the fingertips and a cotton cloth.

Rust: oxalic acid dissolved in hot water or a rust removing product used cold. Be careful with rust stains which are not recent since the cellulose structure will already have been damaged and the fabric tends to hole.

Mould stains: treat with bleach, rinse well (whites and fast coloureds only).

Grass: soap lightly and treat with bleach (whites and fast coloureds only).

Ball point pen and glue: moisten with acetone (*), lay the garment on a soft cloth and dab the stain.

Lipstick: moisten with acetone (*) as above, then treat stains with methylated spirits. Remove any residual marks from white fabrics with bleach.

Red wine: soak in water and detergent, rinse and treat with acetic or citric acid, then rinse. Treat any residual marks with bleach.

Ink: depending on the type of ink, moisten the fabric first with acetone (*), then with acetic acid; treat any residual marks on white fabrics with bleach and then rinse thoroughly.

Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste.

(*) do not use acetone on artificial silk.

Tips For Stain Wand

Warm up a small amount of water to approximately 40°C, wet the stain, pour two or more drops of liquid detergent, spread it over the stain and let it soak for approximately 5 minutes. After this time, apply Stain Wand according to the operating instructions and continue to pour warm water as needed.

Ketchup / Tomato Extract / Beans

Broth: Prepare a solution of two measures of white vinegar with one measure of water. For example: for each tablespoon of water add two tablespoons of vinegar. Mix the solution and wet the entire stain. Apply Stain Wand according to operating instructions and keep wetting the stain with the solution as needed.

Red Wine: Wet the entire stain with cold water; pour two or more drops of liquid detergent; spread it over the stain and let it soak for approximately 5 minutes. After this time, apply Stain Wand according to operating instruction.

Best results are achieved on:

• Fresh stains that are not completely settled;
• Stains that were previously washed but not dried in a dryer nor ironed;
• Small stains, localized in a small area of the garment.

Examples: drops and spills of drinks and/or food; small stains caused by laying the garment on a dirty surface, etc.

Less efficient on:

• Very concentrated or very old stains;

• Stains that were previously washed and dried in a dryer or ironed;
• Large stains, spread on a large area of the garment.

Detergents and Additives

Good washing results also depend on the choice of detergent and use of the correct quantities to avoid waste and protect the environment.

Although biodegradable, detergents contain substances which, in large quantities, can upset the delicate balance of nature.

The choice of detergent will depend on the type of fabric (delicates, woollens, cottons, etc.), the colour, washing temperature and degree of soiling.

Quantity Of Detergent To Be Used

The type and quantity of detergent will depend on the type of fabric, load size, degree of soiling and hardness of the water used.

Water hardness is classified in so-called “degrees” of hardness. Information on hardness of the water in your area can be obtained from the relevant water supply company, or from your local authority.

Follow the product manufacturers' instructions on quantities to use.

Use less detergent if:

• you are washing a small load; • the laundry is lightly soiled;
• large amounts of foam form during washing.

WASHING PROGRAMS

	ProgramIcon Description Options
	Regular Wash*	For an average domestic load of mixed fabrics.	Wash Load / Dirt Level / Soak Time / Rinse Option / Delay End
	Fast Wash	For a very small load of mixed fabrics.	Wash Load / Dirt Level / Soak Time (only ‘No Soak’) / Rinse Option (can not select ‘Extra’) / Delay End
	Save Favourite	Favourite wash program -
	Colours	For colours item of mixed fabrics.	Wash Load / Dirt Level / Soak Time (only ‘No Soak’) / Rinse Option / Delay End
	Delicates	For lingerie, lace, trimmed and embroidered items.	Wash Load / Dirt Level / Soak Time / Rinse Option / Delay End
	Heavy Soil	For a heavily soiled cotton wash load.	Wash Load / Dirt Level / Soak Time / Rinse Option / Delay End
	Woollens	For woollen fabrics labelled “Machine Washable”.	Wash Load / Dirt Level / Soak Time / Rinse Option (only ‘Deep’ & ‘Extra’) / Delay End
	Handwash	Special program for articles of clothing whose label indicates that they must be hand-washed .	Wash Load / Dirt Level / Soak Time / Rinse Option / Delay End
	Bedding	For bedding fabrics labelled “Machine Washable”.	Wash Load / Dirt Level / Soak Time / Rinse Option (only ‘Deep’ & ‘Extra’) / Delay End
	Rinse+ Spin	For items that you want to rinse and spin eg. clothes items you have hand washed in a wash tub.	Wash Load / Rinse Option / Delay End
	Drain+ Spin	For very wet clothes to remove the water.	Delay End
	Tub Cleaning	For cleaning the wash bowl.	Delay End

* "Regular Wash" selected is recommended for a full load of normally soiled cottons.

CARE AND CLEANING

What To Do After You Have Finished Your Washing.

• Press 'OFF' at the ON - OFF Switch.
• Switch off the electricity at the power point.
• Turn off the water taps.
• Leave lid open for a while. This allows time for moisture inside the washing machine to evaporate and for any odours to disperse.

You must DISCONNECT the appliance from the electricity supply, before you can carry out any cleaning or maintenance work.

Cleaning The Dispenser

The dispenser needs to be cleaned regularly, preferably after each wash. Inspect the dispenser after each wash to see if there is any residue of detergent.

To do this proceed as follows:

• Pull the dispenser drawer forward until it stops.
• Lift the front of the drawer up and forward to remove it from the runners.
• Clean the dispenser drawer with hot water and a brush, e.g., an old toothbrush.
• Dry the drawer.

- Before replacing the dispenser back in its recess, clean the inside of the drawer with an old toothbrush.

- Put the dispenser back into its runners and close the drawer.

Cleaning the Lint Filter

Lint is a collection of threads and fluff which comes off your clothes during washing.

Your washing machine collects this lint in the lint filter. It is important to clean out this lint filter, preferably after each wash.

How to clean the lint filter:

- Remove the filter column from the centre of the agitator.

- Unclip the filter bag from the column.

• Turn the bag inside out and remove the lint.
• Wash the filter bag in hot water. Clean the filter bag with an old brush, making sure water can flow through the bag mesh.
• Reassemble the filter to the column and place it back in the centre of the agitator.

Cleaning Your Washing Machine

To clean the inside and outside of your washing machine you should:

• Wipe the surface with a mild dishwashing detergent and warm water.
• Wipe dry with a soft cloth.

Never use solvents, aerosol cleaners, spray pack cleaners, glass cleaners, metal polishes, caustic materials, scourers or general household cleaners on or near the top panel and lid, control panel or other parts of your washing machine.

Cleaning Stains In The Washbowl

Stains and residue in the washbowl can be caused by:

• Metal objects such as bobby pins, dress making pins and nails. Salt.
• Body oils and grease from very dirty or sweaty clothes being deposited around the top of the washbowl.
• Excessive foam during wash if incorrect or too much detergent is used.

• Check all pockets before loading clothes into your washing machine.
• Don't leave wet clothing (especially swimwear) in the bowl for too long before you wash it.

How to clean the washbowl:

• Wipe with a cleaning product which is suitable for stainless steel.
• Oily deposits can be removed by wiping surfaces with a mild dishwashing detergent and warm water.

Never use bleach cleaners or steel wool to clean the stainless steel washbowl.

HELPFUL HINTS IN DEALING WITH WASHING PROBLEMS

Residues On Washed Items

If you are experiencing residue on some clothes, the following tips will help:

• Pre-mix the detergent thoroughly in warm water to improve the dissolving.
• Reduce detergent dosage to between a 1/2 and 2/3 of the manufacturer's standard recommendation to avoid over concentration (the lower water usage requires lower detergent usage).
• Some residue may be re-deposited lint, so be careful to not have lint producing items in a load which has darker clothes.
• Select Deep rinse or Extra rinse and NOT Eco and Fast rinse to help flush more particles away.

Some detergents have ingredients which do not fully dissolve and as a consequence, may leave white residue or particles evident on the surface of darker clothes in the finished wash load.

Similarly, some soils may not dissolve fully, resulting in residue evident on lighter coloured clothes.

Stained Clothes

Treat all stains as soon as possible. The longer you leave a stain the harder it will be to remove. Try soakers and stain removers first.

If you use pre-treatment sprays or stain removers, apply them to the clothes items in a well ventilated area away from your washing machine.

• Use light strokes and don't rub the stain remover into the fabric.
• If you use a chlorine bleach, follow the instructions on the bottle and dilute it before putting it on clothing.
• Test coloured fabrics on an inside seam for colour fastness before using any stain removers or bleaches.
• Test synthetic fabric on an inside seam before using any chemicals or bleaches.

NOTE: Chemicals referred to for stain removal are available from your local supermarket, hardware store or the chemist.

Pre-treatment sprays and stain removers can damage plastic components on your washing machine.

Do not use dry cleaning fluids or solvents near your washing machine. These fluids will damage your washing machine and may cause an explosion.

Yellowing Or Greying Clothes

Problem	Possible causes What to do
Greyness	Incorrect wash times and using insufficient detergent which can cause redepositing of detergent on clothes.Using incorrect type or too much detergent can cause poor rinsing and poor spin performance.Mixing whites with very dirty clothes, eg work clothes.	ONLY use low sudsing detergent for washing machine.Re-sort load, then re-wash using program selections suitable for the fabric.If the water is very dirty or very sudsy, repeat 2 above reducing the amount of detergent you use.
Yellowing	A build-up of oils in clothes that come into close contact with the skin, eg underwear, T-shirts.Ageing of clothes.Iron deposits in the wash water.Use of chlorine bleaches on fabrics with resin finishes.Incorrect drying.	Re-sort load, then re-wash using wash program selections suitable for the fabric.If the water is very dirty or very sudsy, repeat 1 above reducing the amount of detergent you use.

TROUBLESHOOTING

Before calling for service, if you notice the problem, use the guidance in the table below. It will be helpful for your solution with some temporary symptoms. Your washing machine will come back to work as normal before service people come or while waiting in any queue from the service provider.

For some problems, you will get a message in the display screen accompanied by 'Beeps'. The message will be brief information about the problem and what you can do to try and rectify it.

Problem		Possible CausesDisplay	Work to do
Machine not working.		Power not switched on.	Switch on power point.
		No electricity supply through the power point.	Check power point with another appliance.
		Machine not switched on.	Press On-Off switch ON.
	E11	Water taps not turned on.	Turn on taps.
	E17	Out of balance switch off.	Open lid, redistribute load and close lid.
	LD	Lid not fully closed.	Close lid.
Machine has washed load but will not spin Water in washbowl.	E17	Out of balance.	Open lid, redistribute load, close lid.
	LO	Lid not fully closed.	Close lid.
	E20	Drain hose blocked.	Check drain hose for blockage.
	EFO	Too much suds causing motor temperature overload.	Wait a short while, the wash will continue.In future, reduce detergent dose or use low sudsing (front load) detergent.
Will not fill with water.	E11	Water taps not turned on.	Turn taps on.
		Inlet hoses blocked.	Clean tap filters/washers.
Water flowing into washbowl indefinitely.	E13	Drain hose too low.	Raise drain hose or fit a syphon break.Refer to installation instructions for correct positioning of hose.
Machine goes out of balance or vibrates excessively when spinning.	E17	Machine not level.	Make the machine level.
		Levelling feet not adjusted.	Adjust feet to touch the floor.
		Clothes not evenly distributed.	Redistribute clothes evenly.
		Too much water for load size.
Water on floor.		Loose inlet hose connections.	Check connections at taps and rear of machine.
		Incorrect water level for size of load.	Use low water level.
The Stain Wand does not start.		The Washer's plug is not connected to the socket.	Connect the Washer's plug in the socket.
		Stain Wand is not activated.	Activate the Stain Wand.Press the "Delay End" and "►" keys at the same time during 3 seconds, until the Stain Wand buttons turn on.
		The Washer lid is open.	Close the Washer lid.
No water goes out of the Stain Wand.		The tap is closed.	Open the tap.
		The water hose filter is clogged.	Clean the filter.
		No water goes out of the tap.	Check the house's hydraulic installation.
		The water inlet hose is folded or squashed.	Unclog the tap.
		The Stain Wand water button was not pressed.	Press the Stain Wand water button.
Problem Possible Causes	Display Code	What to do
Clothes still dirty after wash program.		Not enough or no detergent.	Check detergent use and rewash clothes.
		Too many clothes in load.	Remove some clothes and rewash.
		Incorrect wash program or temperature selected.	Reselect program or temperature and rewash.
		Incorrect water level selected.	Use a higher water level.
Scraping noise on spin.		Bra wire or other thin items caught between inner and outer washbowls.	If the item is visible, remove it with pliers.
			Use a wash bag in future.
Humming, clicking and other noises.		Bowl rotation at start of wash.	Normal noise.
		Brake activation when stopping after spin.	Normal noise.

TROUBLESHOOTING FAULT DISPLAYS

Fault information and a guide for when you should call for service.

If you have a problem with your washing machine and before you call service, make sure you have followed ALL of the instructions that may remedy the problem. You will find instructions in the 'Troubleshooting' section and in the table below.

When the washing machine detects a problem that requires your attention, you will be alerted. The machine will warn you of this problem by displaying a fault code in the digital display, accompanied by "Beeping".

Fault information and the action you should take are described in the following table.

Description	Display Code	Customer action (Summary)
Not filling with water	E11	Press and hold the “Start/Hold To Pause” button for 1.2 seconds to PAUSE machine.Make sure wall tap is on and hose filter are not blocked. Raise drain hose if water is flowing out of drain hose. Press ‘Start/Hold To Pause’ to re-start wash.If problem remains, call Service.
Flood	E30	If the water is pouring onto the floor, turn OFF both wall taps. Wait a few minutes to see if the fault is corrected.If not, call Service.
Description Customer Displan (Secondary)
Draining problem	E20	Wait a few minutes to see if the fault is corrected. If not, press 'Start/Hold To Pause' then check the drain hose for blockage. Press 'Start/Hold To Pause' to continue the wash. If problem remains, call Service.
Loss of water, while washing	E13	If water level in wash bowl is low and water is flooding the floor, select program 'Drain + Spin ' position, then press 'Start/Hold To Pause'. Should this make things worse, press the power switch and call Service. Otherwise, press 'Start/Hold To Pause' to continue the wash
Water level problem	E30	Wait, this fault may clear itself. If not, select program 'Drain + Spin [6407]' position, then press 'Start/Hold To Pause' to drain the wash bowl. If this problem is repeated, call Service.
Motor fault	ESO	Wait, this fault may clear itself. If not, select program 'Drain + Spin [640W]' position, position to drain the wash bowl. You may have to press 'Start/Hold To Pause' to commence draining. If this problem is repeated, call Service.
Communication error	E91	Call Service.
Machine in pause mode	SP	Press Start/Hold To Pause.
Incorrect option selection	ERR	Choose the correct option.
Out of balance interruption	E17	Make the machine level. Adjust feet to touch the floor. Redistribute clothes evenly, then close the lid to continue
Power down recovery	PR	Wait, this fault may clear itself.

Packaging materials

The materials marked with the symbol

are recyclable.

PE<=polyethylene PS<=polystyrene PP<=polypropylene

This means that they can be recycled by disposing of them properly in appropriate collection containers.

Old machine

Use authorised disposal sites for your old appliance. Help to keep your country tidy!

The symbol 📄 on the product or on its packaging indicates that this product may not be treated as household waste.

Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Ecological hints

To save water, energy and to help protect the environment, we recommend that you follow these tips:

• Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!).
• The machine works more economically if it is fully loaded.
• With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature.
• Measure out detergent according to the water hardness, the degree of soiling and the quantity of laundry being washed.

PE = polyethylene, PS = polystyrene, PP = polypropylene

Washing Programs 78

Care and Cleaning 79

1 Stain Wand 2 Control Panel 3 Protective Glass 4 Lid 5 Front Feet 6 ON/OFF Switch 7 Water Inlet Hose 8 Power Cord 9 Drain Hose 10 Rear Feet 11 Fabric Softener Dispenser 12 Lint Filter 13 Wash Tub 14 Bleach Dispenser 15 Dispenser Drawer 16 Agitator

○ (dry cleaning)

4 Reduce time button 5 Save favourite button 6 Delay End button

7 Display 8 Start/Hold To Pause 9 Stain Wand option, see page 63.

ON/OFF switch

Alarm code

WASHING INSTRUCTIONS

Sorting Laundry

- Remove the filter bag from the stem.