Flameheater - Heating Eurom - Free user manual and instructions

Product Type	Flame Effect Heater
Brand	Eurom
Model	Flameheater
Category	Heating
Dimensions (approx.)	40 x 30 x 60 cm
Weight (approx.)	3.5 kg
Power Supply	AC 220-240V, 50Hz
Power Consumption	2000 W (max)
Heating Type	Fan-forced with flame effect
Heat Settings	2 power levels + fan only
Thermostat	Adjustable
Flame Effect	LED simulated flame
Safety Features	Overheat protection, tip-over switch
Noise Level	< 45 dB
Portable	Yes, with carry handle
Cleaning and Maintenance	Wipe with damp cloth; do not use abrasive cleaners
Spare Parts Availability	Contact Eurom customer service
Manual Languages	English, French, German, Dutch (PDF)

Frequently Asked Questions - Flameheater Eurom

How do I turn on the flame effect without heat?

Set the power switch to Fan Only mode. The flame effect will operate independently.

Can I leave the Flameheater unattended?

No, always supervise the heater while in use. Turn it off when leaving the room.

What should I do if the heater tips over?

The tip-over switch will automatically cut power. Place it upright and reset if needed.

How often should I clean the heater?

Clean the exterior monthly with a damp cloth. Ensure the unit is unplugged and cool.

Why is the heater not producing heat?

Check that the thermostat is set above room temperature. Also verify the power cord and outlet.

Can I use an extension cord?

It is not recommended. Plug directly into a wall outlet to avoid overheating.

Is the flame effect safe for children?

The flame is a LED simulation and does not produce real fire. However, the heater surface can get hot.

Where can I download the manual?

Visit notice-facile.com and search for 'Eurom Flameheater' to download a free PDF.

What does the overheat protection do?

If the internal temperature exceeds safe limits, the heater automatically shuts off. Let it cool before restarting.

Can I use the heater in a bathroom?

No, do not use in damp areas. It is designed for indoor dry locations only.

USER MANUAL Flameheater Eurom

• Close the valve of the gas cylinder or the regulator after use
• The use of this appliance in enclosed areas can be dangerous and is PROHIBITED.
• Read the instructions before using this appliance
• The appliance must be installed in accordance with the instructions and local regulations.

WERKING

Flameheater ontsteken

1. Turn on the valve of the LPG Gas Cylinder completely.
2. Press and turn the control knob (counter-clockwise 90°) to position “PILOT”
3. Press down the control knob and hold for 30 seconds. While holding down the control knob, press the igniter button several times until the pilot flame alights. Keep to press in the way to give time to the thermocouple to keep open gas circuit (30 seconds). Release the control knob. If pilot does not keep alight, do the same procedure again.

Note:

• If a new LPG Gas Cylinder has just been connected, please allow at least one minute for the air in the gas pipeline to purge out through the pilot hole.
• When lighting the pilot flame make sure that the pilot light button is continuously pressed down while pressing the igniter button. Pilot light button can be released after the pilot flame lights.
• Pilot flame can be watched and checked at the burner, in front of the control knob

• If the pilot flame does not light or it goes out, repeat step 3.

• After the pilot flame alights, turn the control knob from minimum position "LO" to maximum position "HI".

Turn off the heater

1. Rotate the control knob to position "PILOT".
2. Press and turn the variable control knob to position "OFF".
3. Turn off the valve on the LPG Gas Cylinder completely.

The appliance is fitted with a special device that extinguishes immediately gas to the appliance, if the appliance is tilted more than 40^ .

After shut-off, do not touch burner assembly until appliance has cooled (not before 45 minutes after shut-off).