PJD6250L - Video projector VIEWSONIC - Free user manual and instructions
Find the device manual for free PJD6250L VIEWSONIC in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type | DLP Video Projector |
| Brightness | 3500 ANSI Lumens |
| Native Resolution | XGA (1024 x 768) |
| Contrast Ratio | 15000:1 (Dynamic) |
| Lamp Type | 190W UHP |
| Lamp Life (Normal/Eco) | 4000 / 6000 hours |
| Zoom Ratio | 1.2x Manual |
| Projection Distance | 1.0 – 10.0 m |
| Inputs | VGA x1, Composite x1, S-Video x1, Audio (3.5mm) x1 |
| Outputs | VGA x1 (monitor out), Audio (3.5mm) x1, USB mini-B (service only) |
| Speaker | 1 x 2W Mono |
| Noise Level (Normal/Eco) | 34 / 30 dB |
| Keystone Correction | Vertical ±40° (Auto/Manual) |
| Dimensions (W x D x H) | 28.0 x 21.5 x 10.8 cm |
| Weight | 2.6 kg |
| Power Consumption (Normal/Standby) | 240W / <0.5W |
| Power Supply | AC 100-240V, 50/60Hz |
| Lamp Replacement | User accessible; replace with ViewSonic RLC-049 model |
| Filter Maintenance | Clean with vacuum every 500 hours |
| Safety Features | Auto power off after 30 min idle, security lock slot |
Frequently Asked Questions - PJD6250L VIEWSONIC
How do I replace the lamp in my PJD6250L?
Turn off the projector, unplug it, wait 15 minutes to cool. Remove the lamp cover screw, open cover, loosen the two lamp screws, pull out the lamp module. Insert new lamp (ViewSonic RLC-049), tighten screws, close cover. Reset lamp timer in menu.
What type of lamp does the PJD6250L use?
It uses a 190W UHP lamp, model RLC-049 from ViewSonic.
How do I clean the air filter?
Turn off and unplug. Locate the filter on the side, slide it out. Gently vacuum the filter from the outside. Reinsert. Do not wash with water. Clean every 500 hours.
Can I mount this projector on the ceiling?
Yes, it supports ceiling mounting. Use a compatible mount that fits the three screw holes (M4) on the bottom. Ensure the mount can support 2.6 kg.
What resolutions does the PJD6250L support?
Native resolution is XGA (1024x768). It can accept up to UXGA (1600x1200) and 1080p via compression.
How do I connect my laptop to the projector?
Use a VGA cable to connect your laptop's VGA output to the projector's VGA input. Alternatively, use a VGA-to-HDMI adapter if needed. Also connect a 3.5mm audio cable for sound.
Why is the projector not turning on?
Check that the power cord is firmly connected and the wall outlet is live. The lamp may have reached the end of life; replace it. If the power LED is off, it may be a fuse issue – contact support.
How do I adjust the image size?
Use the zoom ring on the lens to adjust image size (1.2x). Move the projector closer or farther from the screen. Use keystone correction (Menu > Setup) to correct trapezoid distortion.
What is the throw ratio of this projector?
The throw ratio is approximately 1.96 – 2.35 (distance/width). For a 100-inch screen (2.03m width), place the projector 4.0 – 4.8 m away.
How do I reset the lamp timer after replacement?
Go to Menu > System > Lamp Time. Select 'Reset Lamp Timer' and confirm. This ensures the lamp life counter starts from zero.
User questions about PJD6250L VIEWSONIC
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Video projector in PDF format for free! Find your manual PJD6250L - VIEWSONIC and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PJD6250L by VIEWSONIC.