AT9007G - Refrigerator Acros - Free user manual and instructions

Product Type	Refrigerator
Brand	Acros
Model	AT9007G
Voltage	127 V-
Frequency	50 Hz
Nominal Current	1.03 A
Temperature Control	Independent adjustments for refrigerator and freezer compartments
Shelves	Adjustable glass shelves
Multi-Position Rack	Yes, slides up and out for repositioning
Crisper Drawer	Yes, with partial extension and cleaning feature
Water Dispenser	Yes, internal tank with lever activation
Water Tank Capacity	Approximately 1.5 L (estimated)
Light Bulb	15 W refrigerator bulb
Leveling	Adjustable front legs
Installation Clearance	Top: 7.5 cm, Back: 5 cm, Sides: 1.25 cm
Electrical Grounding	3-prong grounded plug required
Safety Features	Do not use extension cords; keep away from heat sources
Maintenance	Clean condenser, replace light bulb, clean water tank
Compatible Models	AT9007G, AT091FG, AT091FA, AT096FG, AT091FQ
Manufacturer	Industrias Acros Whirlpool, Celaya, Mexico

Frequently Asked Questions - AT9007G Acros

How do I replace the light bulb in my Acros AT9007G refrigerator?

Unplug the refrigerator. Remove the old bulb and replace it with a 15 W refrigerator bulb. Plug the refrigerator back in.

How do I adjust the shelves?

Remove all items from the shelf. Lift the front, slide the shelf out, then reposition it on the rails. Push it fully back into place.

How do I use the multi-position rack?

Remove all parts from the rack. Grasp the rack from the bottom and slide it upwards and out. Release and repeat to reposition at a different height.

How do I use the crisper drawer?

Do not pull the drawer all the way out. To remove for cleaning, lift slightly and tilt forward while pulling. For normal use, slide it in and out as needed.

How do I use the water dispenser?

Fill the tank with drinkable water only. Press a glass against the lever until the desired water level is reached. The drip tray collects any spills.

Why is my refrigerator making unusual noises?

Normal sounds include: whistling from the fan, knocking from the compressor starting/stopping, and water dripping during defrost. Hard surfaces may amplify these sounds.

What should I check if the refrigerator does not work?

Verify the power cord is plugged directly into a grounded outlet (no extension cord). Check the circuit breaker. Ensure the temperature control is not set to OFF. Allow 24 hours after initial setup.

How do I level the refrigerator?

Use a level on top of the refrigerator. Adjust the front leveling legs by turning them clockwise to raise or counterclockwise to lower until the refrigerator is stable and doors close properly.

How do I clean the water tank?

Remove the tank. Do not use a dishwasher. Clean with a soft cloth and mild detergent, rinse well, and dry. Reinstall by aligning the valve and hooks properly.

What safety precautions should I follow?

Always use a grounded electrical outlet. Do not use extension cords. Keep the refrigerator away from heat sources. Do not allow children to play inside the refrigerator. Ensure proper ventilation around the unit.

USER MANUAL AT9007G Acros

How to replace the light bulb

1. Unplug the refrigerator or disconnect power

supply.

1. Replace the light bulb of for refrigerators (15 W).

2. Plug refrigerator o reconnect power supply

NOTE: Do not use any light bulb, make sure

to replace the light bulb with a similar

light bulb suitable for refrigerators.

Remove the shelves

Adjust the refrigerator's racks according to the way the refrigerator is used.

To remove the shelves:

1. Remove all items from the shelves.

2. Lift the top.

3. Slide the grill out

To replace the shelves:

1. Place the back of the shelf

on the rails located on the side walls

1. Guide the front of the grill onto the rails

2. Slide it in until it stops.

How to use the multi position rack

1. Remove all items from the rack.

2. Grab the rack with both hands from the bottom

part and slide upwards and out as indicated on the image. Release and reposition.

How to use the Crisper drawer

Do not pull out the crisper drawer. Turn down the

drawer as the image.

For cleaning lift slightly and slide towards you unt

release.

Water dispenser (some models)

Your refrigerator has a system that allows you to dispense cold water without

opening the door, thus avoiding excessive door openings, consequently,

reducing energy consumption.

Filling tank:

To fill up water in the tank, turn the lid on and fill

It with a jug. After filling close the funnel cover

the initial (closed) position.

Important:

Exclusive use for water

Any other liquid may cause malfunction of the product.

Only use potable water to fill the tank

The manufacturer is not responsible for damage caused to the system if the

tank is supplied with any

Dispensing water:

Press a container or a glass against the lever until the

desired level of water is completed

The container to collect water retains any

drops that may fall while you are dispensing water.

Use a dry cloth to

Cleaning the tank:

Clean the tank frequently. For cleaning, never use the

dishwasher. Remove the water tank by turning it and withdrawing it in the direction indicated in the figure

INTERESTING IS THE EFFECT INTENDED IN THE I-

Hold the tank and remove the lid.

Disengage the tip of the valve by turning it to the

I felt until you feel that the piece Remove it and clean it carefully

Use sponge or soft cloth moistened w

detergent or neutral soap. Rinse well

and dry with a clean dry cloth.

Important:

Do not remove the body of the valve, indicated in the figure.

Replace the tank:

Fit and lock the valve again, as shown in the figure

[Non-Text]

Important

Before replacing the tank, verify that the valve is correctly installed.

Valve is correctly installed

Install the tank on the side hooks

and in the hole in the doo

Verify that the tank is firmly installed.

Note the absence of sp support and the door.

Support and the best

Noises that you may hear

Your new refrigerator may can make sounds, most of them are normal, but hard surfaces like the floor, kitchen walls and the refrigerator itself can make them more noticeable.

Soft whisper, soft whistling

These can be the fan and the air moving

Knocking sounds or rattle noises

The thermostat emits a well-defined knock like sound when the refrigerator

The remote start is a wait defined within the board when the temperature stops and when it starts to work again.

The defroster control clock also emits the same type of sound when the defrost cycle has gone.

cycle begins

Sounds of water

After the refrigerator stops, a drip in the pipeline can be heard for a few minutes.

Water can also be heard running into the water collection tray and a peculiar

sound like water falling on a hot surface during defrosting cycles.

Before calling the technician

VERY IMPORTANT

IT IS THE RESPONSIBILITY OF THE USER TO VERIFY THE FOLLOWING

INFORMATION BEFORE CALLING THE TECHNICIAN:

If you followed the instructions in the installation, use and care manual

correctly, and have questions about the operation of the refrigerator, this guide offers solutions to problems you can detect and correct in your home.

IF THE REFRIGERATOR DOES NOT WORK

IF THE REPRODUCTION DOES NOT WORK

- Connect the plug directly, DO NOT USE CORD EXTENSIONS. Check the ELECTRICAL CONTACT IT COULD BE DAMAGES

- Check the ELECTRIC CONTACT, IT COULD BE DAMAGED, connect another device and test if it works.

- Avoid starting several devices at the same time: THE ELECTRICAL

INSTALLATION MAY OVERLOAD.

- Verify that the TEMPERATURE CONTROL IS IN THE ON-OFF POSITION.

• Make sure the refrigerator is NOT NEXT TO A HEAT SOURCE such as an

over, stove or direct sunlight

- THE DOORS MUST CLOSE HERMETICALLY, check the magnetic gasket of the doors.

• LEVEL THE REFRIGERATOR, remove the wooden bases and adjust the

leveling screws (fi gure 1).

• DO NOT OVERLOAD THE REFRIGERATOR, the circulation of cold air will

be den client.

- Set the TEMPERATURE control knob to MED (medium cold) and wait at least 24 hours before making a new temperature change.

1. PBOE SOIRS MATING 2 NEW TEMPERATURE CHANGE

YOU HAVE NOTICED THAT THE REFRIGERATOR WORKS FOR

EXTENDED PERIODS

- Check that the CONDENSER IS FREE OF DUST AND LINT (figure 1)

- AVOID OPENING THE DOOR CONTINUOUSLY or for prolonged periods.

• DO NOT STORE HOT FOODS and keep them covered.

• Check that there are NO OBJECTS OVER OR BEHIND THE REFRIGERTOR

• The COMPRESSOR DOES NOT WORK PROPERLY, it may be that a low

voltage is present, verify the intensity of the light, if it is low this indicates that it has a low voltage, open to your company of light to parent the new

supply (fi gure 1).

IF AFTER FOLLOWING THESE INSTRUCTIONS, THE REFRIGERATION IS MALFUNCTIONING, PLEASE CONTACT OUR TECHNICAL SUPPORT CENTER

W11347791 Rev. A STM W11226608 Rev. B

STM W11354975 Rev. A

Use and Care

Guide

This manual contains useful information, please read it carefully.

THIS DOCUMENT COVERS THE FOLLOWING MODELS FROM THE

WHIRLPOOL BRAND

AT9007G, AT091FG, AT091FA, AT096FG, AT091FQ

Manufactured by:

Industrias Acros Whirlpool

Address:

Carretera Panamericana km. 280

Celaya Gto. Tel: [phone]

Important Safety Instructions

WARNING

In order to reduce the risk of fi re, electric

shock or personal injury when using your

refrigerator, follow these basic precaution

- Read all the instructions carefully before using your refrigerator.

• Leaving a refrigerator abandoned can cause that someone may get

stuck in it while playing around and suffocate.

• If you are planning on changing your refrigerator, please do it in a safe

way for everyone.

• We recommend removing the refrigerator doors of your ol

disposal or at least, secure the doors with a resistant rope.

- Never leave the refrigerator unattended for unexperienced children to play with it or walk in the refrigerator.

• Never clean the refrigerator parts wit

Never clean the refrigerator parts with flammable liquids, the flames may cause fire or explosions.

• This appliance is not intended for use by persons (including children

whose physical, sensory or mental abilities are different or reduced, or

lack experience or knowledge, unless such persons receive supervision

or training for the operation of the device by a person responsible for you safety:

safety.

- Do not use extensions or adapters without an electrical ground terminal

• Children must be supervised around the refrigerator. Make sure the refrigerator is not used as a toy

FOR YOUR SAFETY

- Do not store gasoline or any other flammable gases or explosive substances

( such as aerosol cans) around this or any other kitchen appliance.

Fumes may cause fi re or explosions.

- If the electrical cord is damaged, this must be replaced by the manufacturer,

authorized repair service technician or by someone qualified. Avoid risks.

- This device is intended for use in domestic and similar applications, such as

a) Kitchen areas for personnel working in stores, offices and other work environments.

environments; b) Forms hotels

b) Farms, hotels, hotels and other work environments; c) In bed and breakfast type environments:

c) In bed and breakfast type environments d) For the preparation of food and similar o

a) For the preparation of food and similar commercial applications KEEP THESE INSTRUCTIONS

KEEP THESE INSTRUCTIONS

Correct Installation

WARNING

This appliance must be connected to an electrical ground.

Do NOT modify the electrical cord. If the electrical plug

doesn't fit, have a qualified electrician to install a proper

electrical outlet on the wall.

Do NOT use a cord extension for this refrigerator.

Contact a qualified electrician if you have doubts about the

contact a qualified electrician if you are electrical grounding of the refrigerator

Not following these prosecutions correctly may save injury.

Not following these precautions correctly may call or even death.

Before plugging your refrigerator to a power supply

- Keep the refrigerator away from outdoor weather

- Keep the refrigerator away from outdoor weather.

- Plug the refrigerator only in an electrical grounded wall outlet

Make sure power supply is within the accepted standards.

- Do not store food in the refrigerator before allowing some time for the refrigerator to anal

for the refrigerator to cool.

- Only use the refrigerator as it's been specifi ed in this guide.

• Schedule maintenance for your refrigerator.

• This refrigerator is intended for domestic use only

• This device is intended for use in domestic and similar applications, such as

Kitchen areas for personnel working in stores, offices and other work

environments

Farms, hotels, motels and other work environments;

In bed and breakfast type environments;

For the preparation of food and similar commercial applications.

(2)

How to install the refrigerator

How to install the refrigerator

Follow these steps before turning on your new refrigerator:

1. Remove all accessories and shelves from inside

2. Place the refrigerator under the following recommendations:

- Leave a minimum space of 3" (7,5 cm) between top of the refrigerator and

the cabinets

- Leave at least a space of 2^ (5 cm) between the refrigerator condenser on

the back of the fridge and the wall.

- Leave a space of 1/2" (1.25 cm) on each side of the refrigerator to ease

installation

• If the refrigerator will be placed against a side wall

leave some additional space to allow the door to

open

1. Level the refrigerator.

- Follow these instructions to rise or lower the height of

the refrigerator. See Figure

- For more accuracy, check the level using a level

on top of the refrigerator. Check if the refrigerator

rocks back to front or side to side v opening the door. Adjust if needed

opening the door. Adjust if needed. We recommend leaving the refrigerator slightly

• We recommend leaving the refrigerator slightly loaned back, as the door can close by itself.

leaned back, so the door can close by itself.

1. Let the refrigerator stand for 2 to 3 hours before connecting to a power supply, this will allow the

connecting to a power supply, this will allow the gas and oil to settle before starting the cooling process.

and oil to settle before

Plug the refrigerator

The voltage required for its operation is 127 V\~ at a

nominal frequency of 60 Hz. Use 15 or 20 A fuses.

Figure 1

Instructions to connect to ground

Procedure for electrical grounding

Your refrigerator is equipped with an electric

Your refrigerator is equipped with an electric cord provided with a 3-terminal grounding

plug. To reduce the possibility of electric

shock to a minimum, the cord must be

connected to an electrical grounded wall

outlet for 3-prong plugs. The installation must be grounded in accordance with the

must be grounded in accordance with the National Electric Code and all local codes

National Electric and regulations

If there is no outlet of this type, it is the responsibility and obligation of the

customer to install a wall outlet with 3 terminals and properly grounded by a

qualifi ed electrician

How to use the refrigerator

Adjust temperature control

Your refrigerator has 2 controls that allow you to regulate the temperature in

the refrigerator and freezer compartment independently.

When you connect for the first time:

- Set the refrigerator and freezer temperature controls to the Cold Medium

- Set the refrigerator and freezer temperature controls to the cold position (★★). Controls range from less cold (★) to colder (★★★,

- Moving the refrigerator control to OFF

- Moving the refrigerator control to 61 stops the freezer and refrigerator from

stops the freezer and refrigerator from cooling but does not disconnect from

electricity.

- Allow the refrigerator time to cool

completely before putting food in it

Its cooling may take several hours.

Adjust the temperature control to keep

the food as cold as you want. The positions suggested above

The positions suggested above are the correct ones for normal home use.

2017-03-05 for the next

Freezer Refrigerator

Shelf extension accessory

This is a useful and practical accessory to store products

on 2 different heights