ZUMMESH-AVBRIDGE-I - Integration Module Crestron - Free user manual and instructions

Product Type	AV Bridge – Wireless Control Integration Module
Brand	Crestron
Model	ZUMMESH-AVBRIDGE-I
Category	Integration Module
Primary Function	Relays RS-232 commands from wireless keypad to an AV controller
Wireless System Compatibility	Zūm Wireless Lighting System and AirMode Presentation System
Communication Ports	COM, COMPUTER, BIMP (with PWR)
Default Serial Protocol	115200 baud, 8 data bits, 1 stop bit, no flow control, no parity
Mounting Method	Surface mount using three screws (not included, appropriate for surface)
Power Supply	Via PWR port (external power supply) or COMPUTER port (bus-powered)
Regulatory Model	M207905003
Compliance	FCC Part 15 Class B, Industry Canada ICES-3 (B)/NMB-3 (B)
Maximum Units per Zūm Space	One AV Bridge
Firmware Updates	Available on Crestron website (www.crestron.com)
Warranty	See www.crestron.com/warranty
Patent Information	Patents listed at patents.crestron.com
Open Source Software	Details at www.crestron.com/opensource
LED Indicator	Setup button LED for status indication
Setup Button	Used for creating or joining a Zūm network
Included Accessories	None (screws not included)

Frequently Asked Questions - ZUMMESH-AVBRIDGE-I Crestron

How do I mount the ZUMMESH-AVBRIDGE-I?

Mount the AV Bridge to any flat surface using three screws (not included) that are appropriate for the mounting surface. For best results, position the device away from interference from nearby RF sources, obstructions, and metal surfaces.

What ports are available on the AV Bridge?

The AV Bridge has three ports: COM for serial communication with the control system, COMPUTER for access and communication with a computer (provides power as well), and BIMP which provides access to the AirBridge via the COM port or when power is not supplied via the COMPUTER port.

How do I create a new Zūm space?

Press the SETUP button 5 times, then press and hold the SETUP button until the LED lights. After approximately 3 seconds, the LED will begin slowly flashing, indicating the Zūm space is created and in Joining mode.

How do I add the AV Bridge to an existing Zūm space?

While the Zūm space is in Joining mode (created by another device), press the SETUP button on the AV Bridge 3 times, then press and hold until the LED lights and starts flashing slowly. The AV Bridge will join the space.

What is the default serial protocol?

The default serial protocol is 115200 baud, 8 data bits, 1 stop bit, no flow control, and no parity.

How do I reset the AV Bridge?

Send the command RESET over the serial connection. The AV Bridge will reboot and respond with a feedback message upon completing the reset.

What is an AVID?

An AVID (AV Bridge ID) is an address used to identify specific devices in the room. It consists of a letter (K for keypad, L for load controller) followed by a two-digit number (e.g., L01). Leading zeros are optional.

How do I update the firmware?

Firmware updates are available on the Crestron website (www.crestron.com). Visit the product page for the ZUMMESH-AVBRIDGE-I and download the latest firmware. Follow the provided instructions to update.

Is the device compliant with FCC and IC standards?

Yes, the AV Bridge complies with FCC Part 15 (Class B) and Industry Canada ICES-3 (B)/NMB-3 (B). Changes or modifications not approved by Crestron could void the user's authority to operate the equipment.

What are the error responses from the AV Bridge?

Error responses include: error 1 for unrecognized command, error 2 for parameter error, error 3 for no unit (invalid AVID), and error 4 for parameter range error. Each is followed by a prompt.

USER MANUAL ZUMMESH-AVBRIDGE-I Crestron

AV Bridge – Wireless Control Integration Module

Installation Guide

Description

The Crestron® ZUMMESH-AVBRIDGE and ZUMMESH-AVBRIDGE-I (AV Bridge) are

wireless control integration modules that relay RS-232 commands from a wireless

keypad to an AV controller

The AV Bridge functions:

- In a Zūm™ wireless lighting system to relay commands from a Zūm Wireless AV

Keypad to the AV control system

- In an AirMedia® Presentation System to relay commands from an AirMedia

Wire NOTES

NOTES:

- Only one AV Bridge can be installed in any system.

- When using the AV Bridge with an AM-200 or AM-300:

• To install, refer to the "Installation" section that follows

• To configure, refer to the AM-200/AM-300 Product Manual (Doc. 8254) at

- To configure, refer to the AM when creetron.com/manuals

Additional Resources

Visit the product page on the Crestron website

(www.crestron.com) for additional information and the latest

firmware updates. Use a QR reader application on your mobile

device to scan the QR image

Installation

To install the AV Bridge, do the following:

1. Mount the AV Bridge to any flat surface using three screws (not included) that

are appropriate for the mounting surface.

NOTE: For best results, position the device to avoid interference from nearby

RF sources, obstructions, and metal surfaces.

②

1. Make connections to the AV Bridge

NOTE: Use either the COM or COMPUTER port (not both) when connecting to

the control system or computer. If both connections are made, the AV Bridge

will use the COMPUTER port to send commands.

• COMPUTER - provides power and communications with the controller

• COM - provides communications with the controller

BWP provides a report to the AV Bidway, providing the COM network.

- PWR - provides power to the Av Bridge when using the COM port or when power is not supplied using the COMPUTER port.

Connect using the COMPUTER Port Connect using the COM and PWR Port

COM port specifications:

G: Ground

• TX: Transmit

- RX:Receive

- Default serial protocol speed: 115.2k baud (8 data bits, 1 stop bits, no flow

control, no parity).

How to Set Up a Zūm Space and Add Zūm Devices

Once all devices are physically installed in a boardroom or conference space, a new Zür

where all devices are physically installed in a board room for conference space, a new Eas space can be created and devices added.

NOTES:

- Only set up one Züm space at a time.

- For simplified setup of a Züm space, use the Züm app on a mobile device.

Step 1 Create a New Zūm Space

Creating a Z0m space defines the area where the devices are located, such as a

boardroom or conference room. A Zūm space is created with a keypad, dimmer or

switch, a J-box device, or an AV Bridge.

NOTES:

- Creating a Zūm space can only be performed by one device in the space.

• A Züm space cannot be created from a battery-powered keypad.

To create a new Züm space using an AC powered keypad, dimmer, or switch:

1. Press the bottom button 5 times

2. Press and hold the bottom button until the LED on the device lights. After

2.1 Less and hold the bottom bottom after the LED on the device lights. After approximately 3 seconds, the device LED begins slowly flashing. This indicate

that the Züm space is now created and in Joining mode, allowing you to add

To create a new Zūm space using a J-box device or an AV Bridge:

1. Press the SETUP button 5 times.

2. Press and hold the SETUP button until the LED on the device lights. After

approximately 3 seconds, the device LED begins slowly flashing. This indicate

that the Zūm space is now created and in Joining made, allowing you to add

NOTE: The device that is used to create the Zum space is automatically added to

the space and does not need to be added in Step 2.

Step 2 Add the AV Bridge to the Zūm Space

After a new Züm space is created, add the AV Bridge while the space is in Joining mode

NOTES:

NOTES.

- A Züm mesh device can belong to only one space.

- Joining mode ends automatically after 4 minutes.

To add the AV Bridge

1. Press the SETUP button 3 timer

2. Press and held the SETUP button until the LED on the AV Bridge lights. The LED

3. Press and hold the SETUP Bottom until the LED on the AV Bridge lights. The LED on the AV Bridge will start to flash slowly to indicate that it has joined the space

Step 3 Complete Zūm Space Setup

To finish creating a Zūm space, press any button on a device that is part of the Zūm

space to exit Joining mode.

AV Bridge Command List

AND WE ARE TO understand

AV Bridge Serial Protocol and Syntax

Data packets are carriage-return delimited (0xd) ASCII text (lines).

- All commands and responses are case insensitive.

• Line feeds (OxOa) are ignored.

- White space is not permitted in command, except for pass-through commands. The AV Bridge responds to command with the AVR prompt

- The AV Bridge responds to commands with the AVB> prompt. - Error messages are sent before the prompt

- Characters sent before the AV Bridge returns the AVB> prompt are discarded.

Special Characters sent to the AV Bridge

• !Command: sets a value or triggers an action (e.g., lights off, recall scene, etc.)

- ? Request: used to query a value or state of a Züm device (e.g., the dimmer level)

- \$ Pass-through command: used to invoke debug commands

cial Characters sent from the AV Bridge:

- Response: sent in response to a command (!) or request (?)

- ^ Feedback: sent when a condition in the room changes (e.g., scene change,

occupancy change, button press, etc.). The Filter command may prevent certain

feedback from being displayed.

- \ line continuation: sent at end of a line when multiple responses are issued

AV Bridge IDs

The AV bridge addresses specific room devices using an AVID (AV Bridge ID). The AVID is comprised of a K (keypad) or L (load controller) and a two digit number that is assigned to the device, such as L01, L02, K01, K02, K03, etc.

NOTES:

- The leading O is not needed when referencing an AVID for example, L1 or L01

- The leading O is not needed when referencing an AVID, for example, LT

- In the commands that follow, "[id]" would be substituted with an AVID.

Error Responses

The following error messages can be received from the AV system or the AV Bridge.

ERROR TYPE ERROR RESPONSE ERROR		PRIORITY	COMMENTS
Command error -error 1 Command not recognized; blank lines			not treated as an error
Parameter error	-command.err.param	2	Missing or too many parameters passed or an invalid AVID referenced (e.g., invalid category or two-digit number)
Non-existent device referenced	-command.err.no-exist	3 "command"; any command referencing a device by AVID
Parameter range error	-command.ext range	4 Error with parameter value other than AVID

Command Line Pass-Thru Command

Commands that start "\$" are passed to the AV bridge's command line processor for

low-level debugging

Administrator Commands

Debug Command

The Debug command sets the debug control state. The debug state can also be

queried. When the debug state changes, the feedback response is issued by the AV

Bridge.

Command Format	Command Response	Query Format	Query Response
!debug.[enable|disable]	AVB>	?debug	-debug.[enabled|disabled]

Enable debugging:

AVB> !debug.enable

AVE>

Echo Command

The Echo command enables or disables the device echo. The echo state can also be

queried. When the echo state changes, the feedback response is issued by the AV

Bridge.

Command Format Command Response		Query Format	Query Response
!echo.[enable]	AVB>	?echo	~echo.[enabled]
Note:	Determines whether the device local echos the incoming character stream.

Turn on Echo:

AVR: Iecho enable

AVB>

Fw (Firmware) Command

The Fw query reports the version of the firmware

Query Format Query Response
?fw	-fw.[version]

Query the firmware version:

AVB> ?fW

\~£w,xxxxyyzzzz

AVE>

CRESTRON

Reset Command

The Reset command resets the AV Bridge. When the AV Bridge is reset, a feedback

response is issued by the AV Bridge

Command Format	Command Response
reset	AVB>
Note:	This will reset the AV bridge. The AV bridge will respond with the ~reset confirmation before resetting.

Reset the AV Bridge:

AVB> !reset

AVB>

SetAVID Command

The SetAVID pass-through command assigns an AVID to a device. This can be used to

change an AVID when a device is replaced, or it can be used to implement preplanned

AVID assignments based on the device's serial number. The -a parameter allows an

AVID to be changed to another AVID. The -s pa

to a device based on the device's serial number.

Command Format	Command Response
SetAVID -a [AVID] [AVID]	AVB>
SetAVID - s [SN] [AVID]
Note:	Permits reassignment of an AVID.

Replace AVID L01 with L03:

AVB> \$SetAVID -a [L01] [L03]

AVB>

Assign AVID L04 to serial number 123456789:

AVB> SSetAVID -a [L04] [123456789]

AVB>

DeleteDev Command

The DeleteDev pass-through command deletes a device from the AV Bridge. This can

be used to free up an AVID for use by another device, or it can be used to remove a

device from the system. The -a parameter allows an AVID to be removed using an

AVID. The -s parameter allows an AVID to be removed from a device based on serial

number.

Command Format	Command Response
DeleteDEV -s [AVID]	AVB>
DeleteDEV -s [SN]
Notes:	Permits deleting an AVID.-s can be used only when in Master mode (i.e., no net bridge in the room).

Delete AVID L01:

AVB> SDeleteDEV -a [L01]

AVB>

Delete the AVID from a device with the serial number 123456789:

AVB> \$DeleteDEV -s [123456789]

AVE>

Züm Network Management Functions

Permitiogin Command

The Permitjoin command places the room into Joining mode. The room's permitjoin

state can also be queried.

Command Format	Command Response	Query Format	Query Response
|permit|join, [enable|disable]	AVB>	?permit|join	-permit|join, [enable|disable]
Note:	Joining mode automatically times out after 4 minutes.

Enter Joining mode:

AVB> !permitjoin.enable

AVE>

Form Command

The Form command creates a new Züm network.

Command Format	Command Response
Form	AVB>
Note:	The device leaves any network and forms a new network. The response should be immediate. The form command puts the network in permit joining mode. It can use Permitjoin command to disable joining immediately. If not, Permitjoin times out.

Form a new network:

AVB> !form

AVB>

Identify Command

The Identify command identifies AC-powered Züm devices that are part of the network by flashing their LED.

Command Format Command Response
Identify.[Id|stop] AVB>
Notes: Times out after	3 minutes. The stop parameter stops.

Identify load controller with AVID L01:

AVB> !identify.L01

AVB>

Join Command

The Join command tells a device to join a Züm network that is in Joining mode.

Command Format	Command Response	Query Format	Query Response
[join AVBs ?] join -join	{success|failure}
Note: If the device was commanded to join a network, the -join response appears only after a success or failure. If a query was issued, the response should be immediate.

Join a network that is in Joining mode:

AVB> !join

\~join.success

AVE>

Request the join state of the device:

AVB> ?join

\~join.success:

Button Command

The Button response is sent in response to a button press.

Command Format	Command Response Feedback Response
Ibutton. [tap]hold|release. [button].[id].[SN]	AVB> ^button.[tap]hold|release.	[button].[id].[SN]
Notes: Button values:	tap, hold, release.SN: serial number string.

When the AV Bridge receives information about a button 1 hold from a keypad with Wi-Fi (W) and Wi-Fi (W) to a button,

AVID KU1, the AV Bridge sends the following response:

AVB> "button.hold.1.K01.123456789

Level Command

The Level command sets the load controller level. The load controller level can also be
queried. When the load controller's state changes, the feedback response is issued by the AV Bridge.

Command Format	Command Response	Query Format	Query Response	Feedback Response Format (filter-level == 2)
level [,level],[id]	AVB>	?level [,id]	^level [,level],[id]	-level [,level],[id]
level [,level]		Cannot request all dimmer levels at once
Notes: Level is percentage of max brightness (0-100), with or without leading zeros.There is no trade time associated with this command.				Sent in response to level.[level],[id],level [,level]or when changed from within room.

Establish a 50% load level for the load controller assigned to AVID L01:

AVB> !level.S0.L01

AVB>

AVB> ^level,50.L01

Set all load controllers to 100 (when there are two load controllers in the room—AVID L01 and L02).

LOT and LO2).

AVB> :level.fuc AVB>

AVB> ^level.100.L01

AVB> ^level.100.L02

Request a load level of the load controller assigned to AVID L02:

AVB> ?level.L02

-level,74,L02

AVB>

Filter Command

The Filter command sets the feedback message filtering. The filtering state can also be queried.

Command Format	Command Response	Query Format	Query Response
filter.[0|1|2]	AVB>	?filter	-filter.[0|1|2]
Note:	Feedback messages sent for each setting:0: Only button action messages (default).1: Button actions and room-level state changes.2: Button actions, room level, and device level state changes.

Change the feedback message filtering:

AVB> |filter,2

AVB:

Dev Command

The Dev command forms a list of all devices in the room.

Query Format	Query Response
?dev	~dev [Device ID] [status] [SN]
	or
	~dev none
Notes:	Repeats the response for each device with an AVD. Load controllers follow the form Lxx and keypads follow Kxx.For each device an individual response line is sent.All but the last response have a line continuation character ") at the end of the line.If no devices exist, response is ~dev none.Status: "active" or "missing".SN: Serial number string.

List all devices on the Zum network;

AVB> ?dev

\~dev.L01.active.123456789

-dev.K01.active.213456789

-dev.L02.missing.312456789

AVE.

Plug Command

The Plug command turns the plug load controller on or off. The plug load controller

state can also be queried. When the plug load controller's state changes, the feedback response is issued by the AV Bridge.

Command Format	Command Response	Query Format	Query Response	Feedback Response Format (filter-level == 2)
lplug.[on]off]	AVB>	?plug	~plug.[on]off]	^plug.[on]off]
Notes:	Plug load controllers cannot be individually controlled. The feedback is OR'd in case there are multiple plug controllers that get out of sync.			Sent in response to |plug. [on]off] or if change sent from within room.

Turn on the plug load controllers:

AVB:

AVB:

AVB:

Bamp Command

The Ramp command increases or decreases the dimmer levels. When the ramp state

changes, the feedback response is issued by the AV Bridge

Command Format	Command Response
Irimp.[up]down[stop]	AVB>
Irimp.[up]down[stop].[d]
Note:	The lights ramp using an up or down command, and then stop with a stop command. The ramp stops based on the device timeout setting or if a stop command is received. When ramping down, lights stop at their minimum level and do not turn off.

Ramp up all load controllers. To prevent ramping to 100, issue the ramp stop command:

AVB:

AVB:

AVB NVR

Scenesave Command

The Scenesave command saves the current light levels as a scene

Command Format	Values	Feedback Response
!scenesave.[number]	1-16	-scenesave.[number]

Save the current light levels for scene 5:

AVB>

AVB>

Sync Command

The Sync command queries the system to verify that an AV Bridge is present. When the

AV Bridge is booted up, a feedback response is issued by the AV Bridge.

Query Format	Query Response	Feedback Response
?sync	-sync	^sync
Notes:	This allows the AV control system to verify that the AV bridge is up and running.	Sent after boot when AV bridge is ready to process AV commands.

Query the sync status:

AVB> ?sync

-syn

AVB>

Room-Level Commands

Room-level commands send command and request commands to an entire room.

Responses are sent based on the state of the room.

Command Format	Query Format	Query Response	Feedback Response Format (filter-level >=1)
room.[Field].[value]	?room.[Field]	~room.[Field].[value]	^room.[Field].[value]

Scene Command

The Scene command sets the room lights to their scene levels. The room's current scene

The scene commands the room lights to their scene level. The room's scene can also be queried. When the room's scene changes, the feedback response is issued

by the AV Bridge

Field	Values	Query Format	Query Response	Feedback Response
Scene	1-16	?room.scene	-room.Scene.10	^room.Scene.10

Set a room-level scene to scene 1

AVB>

AVB>

AVB> ^room,scene.1

Request the current scene in the room:

AVB>

\~room,scene.#

AVB>

Occupancy Command

The Occupancy command sets the room occupancy state for the room. The room's

occupancy state can also be queried. When the room's occupancy state changes, the feedback response is issued by the AV Bridge.

Feedback response is issued by the Av Bridge.

Field	Values	Query Format	Query Response	Feedback Response
Occupancy	Occupied, Vacant	?room.occupancy	-room.occupancy, [occupied]vacant	^room.occupancy, [occupied]vacant

Set the room as vacant:

AVE>

AVB>

AVB>

Occ-action Command

The Occ-action command enables or disables the occupancy action state for the

room. The room's occupancy action status can also be queried. When the room

Field	Values	Query Format	Query Response	Feedback Response
Occ-action	Enable, Disable ?room	m.occ-action -room	m.occ-action.[enable|disable]	^room.occ-action.[enable|disable]

Disable occupancy actions:

AVE> !room.occ-action.disable

Ave>

AVB> ^room.occ-action.disable

Query occupancy action status:

AVB> ?room.occ-action

\~YOOO AUD>

AVE>

Lights Command

The Lights command toggles the lights for the room. The room's light state can also

be queried. When the room light status changes, the feedback response is issued by

Field	Values	Query Format	Query Response	Feedback Response
Lights	On, Off	?room.lights	-room.lights. [on/off]	^room.lights. [on/off]

Enable occupancy actions:

AVE>

AVE>

AVE>

Query lights status:

AVE>

\~YOOO AUD>

AVE>

Photo Command

The room's photocell value can be queried. When the room's photocell value changes,

the feedback response is issued by the AV Bridge.

Field	Values	Query Format	Query Response	Feedback Response
Photo	0-65535	?room.photo	-room.photo. [0-65535]	^room.photo. [0-65535]

Query photocell level:

AVE>

\~room.photo,6813

AVE>

Daylight-Action Command

The Daylight-Action command enables or disables daylighting for the room. The

The daylight light command enables of disables daylighting for the room. The room's daylight-action value can also be queried. When the room's daylight-action value changes, the feedback response is issued by the AV Bridge.

value changes, the feedback response is issued by the AV Bridge

Field	Values	Query Format	Query Response	Feedback Response
Daylight-Action Enable, Disable	?room.daylight-action	-room.daylight-action. [enable]disable	-room.daylight-action. [enable]disable	^room.daylight-action. [enable]disable

Enable daylight action:

AVB> !room.daylight-action.enable

AVE>

AVB> ^room.daylight-action.enable

Quer

AVB> ?room.daylight-action

\~room.daylight-action.enable

AVB>

Regulatory Model: M201909003

This product is listed to applicable UL® Standards and requirements tested by Intertek® services. Ce produit est homologué selon les normes et les exigences UL applicables par Intertek Prestations de service.

Intertek

As of the date of manufacture, the product has been tested and found to comply with

specifications for CE marking.

ce

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following

conditions: (1) This device may not cause harmful interference and (2) this device must accept

any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for

compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with

oses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3 (B)/NMB-3(B)

The product warranty can be found at www.crestron.com/warranty

The specific patents that cover Crestron products are listed at patents.crestron.com.

Certain Crestron products contain open source software. For specific information, please visit

www.crestron.com/opensource.

Crestron, the Crestron logo, and Züm are either trademarks or registered trademarks of

Crestron Electronics, Inc. in the United States and/or other countries. The ETL logo is either a

trademark or registered trademark of Intertek Testing Services NA in the United States and/or other countries. UL is either a trademark or registered trademark of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

©2019 Crestron Electronics, Inc.

Crestron Electronics, Inc.

15 Volvo Drive, Rockleigh, NJ 07647

Tel: 888.CRESTRO

Fax: [phone]

www.crestion.com

Installation Guide - DOC. 7916E

(2047921)

09/12/19

Specifications subject to change without notice

change without notice.