SEP 702BT - Earphones SENCOR - Free user manual and instructions

Product Type	Wireless Over-Ear Headphones
Brand	Sencor
Model	SEP 702BT
Bluetooth Version	5.3
Driver Diameter	30 mm
Impedance	32 Ω
Sensitivity	99 dB ± 3 dB
Frequency Range	20 Hz - 20 kHz
Battery Capacity	400 mAh
Charging Time	1 hour
Playing Time	7 hours (at 50% volume)
Charging Connector	Micro USB
Audio Input	3.5 mm AUX (cable included)
Memory Card Support	TF/microSD (FAT32)
Controls	On/Off, Volume, Play/Pause, Track Forward/Backward, Source Switch (M)
LED Indicator	Red when charging, off when fully charged
IP Rating	IP20
Bluetooth Range	Up to 10 meters
Safety Features	Volume limitation to protect hearing
Included Accessories	Audio cable (3.5 mm), Micro USB charging cable, User manual

Frequently Asked Questions - SEP 702BT SENCOR

How do I pair the Sencor SEP 702BT with my smartphone?

Turn on the headphones by pressing and holding the On/Off button until you hear a greeting. On your smartphone, enable Bluetooth and search for devices. Select "SEP 702" from the list. If prompted for a PIN, enter 0000. The headphones will connect automatically.

How do I charge the headphones?

Connect the included Micro USB cable to the charging port on the headphones and to a USB power source. The red LED will indicate charging. When the battery is fully charged, the red LED turns off. Charging time is approximately 1 hour.

What is the battery life of the SEP 702BT?

At 50% volume, the battery provides up to 7 hours of playback time. Higher volume reduces battery life. A low battery is indicated at 20% and again at 10%.

Can I use the headphones while they are charging?

Yes, you can use the headphones while charging, but it is recommended to charge them fully before first use. Note that using them during charging may extend charging time slightly.

How do I play music from a memory card?

Insert a TF/microSD card (formatted as FAT32) into the memory card slot with the contacts facing outward. The headphones will automatically switch to memory card mode and start playing. Use the M button to switch sources if needed.

What should I do if the headphones won't turn on?

First, charge the headphones for at least 30 minutes. If they still do not turn on, try resetting them by pressing and holding the On/Off button for 10 seconds. If the issue persists, contact an authorized service center.

How do I reset the Sencor SEP 702BT?

To reset, press and hold the On/Off button for about 10 seconds until the LED flashes or you hear a confirmation sound. This will clear paired devices and restore default settings.

Are the SEP 702BT headphones waterproof?

No, they are not waterproof. They have an IP20 rating, meaning they are protected against solid objects larger than 12.5 mm but not against water. Do not immerse in water or expose to heavy rain.

How should I clean the headphones?

Use a soft, dry cloth to wipe the exterior. Do not use liquid cleaners or abrasive materials. Keep the ear cushions dry and avoid moisture entering the ear cups.

Can I adjust the volume on the headphones?

Yes, press the Volume Up or Volume Down buttons to adjust. Long-press the Volume Up or Down buttons to skip to the next or previous track. Always start at a low volume to protect your hearing.

USER MANUAL SEP 702BT SENCOR

Line drawing of a pair of outdoor headphones (no text or symbols)

USER'S MANUAL

NÁVOD K OBSLUZE

NÁVOD NA OBSLUHU

INSTRUKCJA OBSŁUGI

HASZNÁLATI ÚTMUTATÓ

UPUTSTVO ZA UPOTREBU

KORISNIČKI PRIRUČNIK

ΕΓΧΕΙΡΙΔΙΟ ΧΡΗΣΗΣ

Children wireless headphones

Micro USB charging cable

2.Description of BT Headphones and Controls

|1| Memory card slot
|2| On/Off button (long press) PLAY/PAUSE (press 1×)
|3 | "M" button change source (Bluetooth, memory card)
|4| Volume down button (press 1×) previous track (long press)
|5| Volume up button (press 1×) Next track (long press)
|6| Socket for audio AUX IN mini jack (3.5 mm)
|7| MicroUSB charging connector
|8| LED connection/charging status indicator
IL Left earpiece - left audio channel
|R| Right earpiece - right audio channel

3. Putting into operation

Before first use, be sure to read the safety instructions contained in this user's manual carefully.

Before first use, start charging the headphones to the maximum level.

Turning on the headphones – press and hold the power button and wait for the headphones to greet you.

Turning off the headphones – press and hold the power button and wait for the headphones to announce the shutdown.

Warning: To prevent damage to your hearing, always keep the volume level of your device to a minimum before connecting BT headphones to your mobile device.

Note: The BT headphones will turn off after a longer period of inactivity unless they are paired to another device.

4. Bluetooth

To pair the BT headphones with your mobile device, do the

mZ

following:

Turn on the BT speaker and search for its Bluetooth name "SEP 702" on the device to which you wish to pair and start the pairing process. If you are requested to enter a pairing code while your device and the BT headphones are pairing, use the following code: "0000".

To cancel the pairing process, disconnect the BT earphones from your mobile device (cancel the Bluetooth pairing).

Note: To ensure a stable Bluetooth connection, make sure that the distance between the BT headphones and your paired device is kept within 10 meters. Depending on ambient interference, in some cases it may be necessary to maintain a shorter distance between the BT headphones and the paired device.

5. Memory Card Playback

Insert the memory card with the contacts towards the outside of the headphones (side of the headphones). When you insert a memory card, the BT headphones will automatically start playing back its contents. If there is no file to play on the memory card, the BT headphones will switch to Bluetooth mode. To release the TF memory card, press it gently into the body of the BT headphones with your fingernail or a blunt instrument and the card will release. Then you can carefully remove it with your fingernails (or with tweezers). Store audio files on the memory card in the order you want them to be played back later.

Attention: Due to a number of devices on the market, compatibility and playback support are not guaranteed for all media. The memory devices you want to connect should be tested in advance and/or formatted as FAT32. The playback of protected media, files or content stored inside them may fail.

6. Audio AUX IN

The headphones are equipped with a 3.5mm jack. Your device can be connected to the BT headphones using the audio cable included in the box with the headphones. First connect the audio connector to your appliance and then into the socket in the BT headphones.

Notice: Before connecting your device to the BT headphones, ensure that the output signal from your device is at its minimum level (minimum output volume). This will prevent damage to the BT headphones and your hearing.

7. Charging

A charged battery provides power for several hours of operation at normal volume levels. A high volume consumes more battery power; therefore, we recommend listening at normal volume levels. Charging of the BT headphones will be indicated by a red LED. An extinguished red LED indicates a fully charged battery.

Attention: For charging, use only the original accessories supplied with the appliance. To achieve maximum battery life, it is advisable to start charging the battery only when the battery is low (10% - 20%). Charge continuously until fully charged. If the battery life is already very short, it is exhausted and we recommend you contact an authorised service centre for more information.

Recommendation: A low battery is first reported at 20% and then at 10%. We recommend that you start charging to full level at the first sign of a low battery.

Recommendation: If your headphones are not to be used for an extended period of time, we recommend to fully charge the batteries once every two to three months.

Specification:

• Bluetooth Version 5.3
• Impendance:32Ω
• Driver Diameter: 30 mm
• Sensitivity: 99dB±3 dB
• Frequency Range: 20 Hz - 20 kHz
• IP20
• Battery Capacity: 400 mAh
- Connector: MicroUSB
- Charging Time: 1h
- Playing Time: 7h (50% volume)

mZ

Safety Notice:

Please observe the rules of the Country or Region which you are in while driving.

Do not disassemble or modify the headset at any reason, otherwise, it may damage or burn the headset.

If there is any quality problem, please send headset to authorized service center for repairing.

Please keep the equipment along with all the accessories out of the reach of children and pets.

Extreme temperatures will cause the device deformation, reduce the charging capacity and shorten the working life.

Please do not immerse the earphone into water. Guarantee will be lost if damage is caused by immersed into water.

It will damage your hearing if you listen with high volume for a long time. It is recommended that only use the lowest volume which is necessary for speaking and listening to music.

Instructions and information regarding the disposal of used packaging materials

Dispose of packaging material at a public waste disposal site.

Disposal of used electrical and electronic appliances

The meaning of the symbol on the product, its accessory or packaging indicates that this product shall not be treated as household waste. Please, dispose of this product at your applicable collection point for the recycling of electrical & electronic equipment waste. Alternatively in some states of the European Union or other European states you may return your products to your local retailer when buying an equivalent new product. The correct disposal of this product will help save valuable natural resources and help in preventing the potential negative impact on the environment and human health, which could be caused as a result of improper liquidation of waste. Please ask your local authorities or the nearest waste collection centre for further details. The improper disposal of this type of waste may fall subject to national regulations for fines.

For business entities in the European Union

If you wish to dispose of an electrical or electronic device, request the necessary information from your seller or supplier.

Disposal in other countries outside the European Union

If you wish to dispose of this product, request the necessary information about the correct disposal method from local government departments or from your seller.

This appliance complies with EU rules and regulations regarding electromagnetic and electrical safety. Changes to the text, design and technical specifications may occur without prior notice and we reserve the right to make these changes.

Hereby, FAST CR, a.s. declares that the radio equipment type SEP 702 BT is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address: www.sencor.eu

1. Obsah balení

Sluchátka

Audio jack 3,5 mm

Pure horizontal and vertical lines without any text, numbers, or symbols

SENCOR

Manufacturer: FAST CR, a.s.

U Sanitasu 1621

25101 Ricany

Czech Republic