ELPC40B - Rear Camera BOSS - Free user manual and instructions

Product Type	Rear View License Plate Mount Camera
Brand	BOSS Audio Systems
Model	ELPC40B
Power Supply	DC 12V
Lens Angle	170°
TV System	NTSC
Video Output	1.0 Vp-p, 75 Ω
S/N Ratio	< 48 dB
IP Rating	IP68
Operating Temperature	-30°C to +70°C (RH 95% Max.)
White Balance	Auto
Minimum Illumination	0.5 Lux
AGC	Auto
Resolution	480 TV Lines
Electronic Shutter	1/60 (NTSC)
Effective Pixels	628 x 586
Mounting Type	License Plate Frame Mount with Hidden Bracket
Image Features	Distance Guide Lines (removable), Image Invertible
Safety Warning	Do not rely solely on reverse camera; always check surroundings.
Troubleshooting	Refer to manual for common issues (no image, blur, shake, slant).
Compliance	Parameters subject to change without notice.

Frequently Asked Questions - ELPC40B BOSS

What power supply does the ELPC40B camera require?

The camera requires a DC 12V power supply.

What is the lens angle of this camera?

The lens angle is 170°.

What is the IP rating of the ELPC40B?

The camera has an IP68 rating, making it water and dust resistant.

How do I remove the distance guide lines?

Turn the system off, then cut the white loop wire at the camera connection points. Insulate both ends. Reconnecting the wire will restore the lines.

Can I invert the camera image?

Yes. Turn the system off, cut the blue loop wire at the connection points, and insulate both ends. Reconnecting the wire returns the image to original orientation.

What TV system does the camera use?

It uses the NTSC TV system.

What is the minimum illumination for the camera?

The minimum illumination is 0.5 Lux.

How do I troubleshoot if no image appears?

Check that the power cable is securely connected, ensure good video connection, confirm reverse gear is engaged, and verify monitor setup.

What should I do if the image is blurry?

Check for water, stains, or dust on the camera lens and clean it.

Is it safe to rely solely on the reverse camera?

No, the manual warns: Do not fully rely on reverse camera when backing up. Always use mirrors and look around.

USER MANUAL ELPC40B BOSS

Power Supply	DC 12v
Lens Angle (Deg.)	170°
TV System	NTSC
Video Output	1.0vp-p, 75Ω
S/N Ratio	< 48 dB
IP Rating	IP68
Operating Temp. (Deg. C)	-30°C ~ +70°C (RH 95% Max.)
White Balance	Auto
Minimum Illumination	0.5 LUX
AGC	Auto
Resolution (TV Lines)	480
Electronic Shutter	1/60 (NTSC)
Effective Pixels	628 x 586

Above parameters can be modified without notification.

BOSS Audio Systems

3451 Lunar Court • Oxnard, CA 93030

www.bossaudio.com

800-999-1236 US Toll-free

805-751-4853 Customer Service

Tech Support: www.bossaudio.com/support/technical-support

USER'S MANUAL ELPC40B

REAR VIEW LICENSE PLATE MOUNT CAMERA

FEATURING HIDDEN MOUNTING BRACKET

Black handheld device with attached cable and sensor, shown against a red and white background (no text or symbols visible)

DO NOT FULLY RELY ON REVERSE CAMERA WHEN BACKING UP.

Complete all required connections so that all lines are hidden in vehicle.

2. CAMERA INSTALLATION

Camera should be installed in the following configuration:

License Plate Frame Mount – Align camera frame with top-set of screw holes on license plate or license plate frame. Affix camera using license plate mount screws. See: (diagram 1)

Attention: The camera switch is controlled by reverse gear shift.

OPTIONAL

To remove the distance guide lines:

1. Turn the system OFF before proceeding
2. Cut the white loop wire located at the connection points (camera end).
3. Insulate the wire, using tape or crimp connectors on both ends.
4. Reconnecting the wire will display the guide lines again.

To invert the camera image:

1. Turn the system OFF before proceeding
2. Cut the blue loop wire located at the connection points (camera end)
3. Insulate the wire, using tape or crimp connectors on both ends.
4. Reconnecting the wire will orient the image back to its original position.

TROUBLESHOOTING GUIDE

The following checklist might help to solve the problems when using this unit. Please double check to ensure connection and procedure of operation is done properly before using checklist.

PROBLEM	CAUSE/SOLUTION
NO IMAGE	Check that power cable is securely connected.Check to ensure there is a good connection between video-in and monitor.Check that REVERSE GEAR is engaged.Check to ensure correct monitor setup.
IMAGE BLURRING	Check for water/water stain or dust on camera lens.Clean camera lens
IMAGE SHAKING	Check to insure camera is mounted and secured tightly
IMAGE SLANTED	Adjust camera mounting bracket

NOTE:

If problems persist – consult nearest service dealer. DO NOT attempt to disassemble or modify unit.