ADE 906-2 G - Range hood Arçelik - Free user manual and instructions

Product Type	Range Hood
Brand	Arçelik
Model	ADE 906-2 G
Width	90 cm
Depth	50 cm
Height (min-max)	60-110 cm (adjustable)
Net Weight	Approx. 15 kg
Power Supply	220-240 V ~ 50 Hz
Motor Power	200 W
Lighting Power	2 x 1.5 W LED
Max Extraction Rate	650 m³/h
Noise Level (max speed)	62 dB(A)
Number of Speeds	3
Filter Type	Aluminum grease filter (washable)
Control Type	Slider controls
Exhaust Diameter	150 mm
Energy Class	A+
Installation Type	Built-in / Under-cabinet
Cleaning	Wipe with damp cloth; grease filter dishwasher safe
Safety Features	Thermal fuse, automatic shut-off
Spare Parts Availability	10 years after end of production

Frequently Asked Questions - ADE 906-2 G Arçelik

How do I install the Arçelik ADE 906-2 G range hood?

Installation should be carried out by a qualified technician. Ensure the hood is mounted at least 65 cm above gas hobs and 55 cm above electric hobs. Secure the hood to the wall using the provided brackets and connect the exhaust duct (minimum diameter 150 mm) to the exterior. Electrical connection must comply with local regulations.

How often should I clean the grease filter?

The aluminum grease filter should be cleaned every 2-3 months under normal usage. It is dishwasher safe at low temperature. More frequent cleaning may be necessary for heavy cooking to maintain optimal extraction performance.

How do I replace the LED lights?

The LED lights are not user-replaceable. If they fail, please contact an authorized service center or a qualified electrician for replacement to avoid damage.

Why is the range hood noisy?

Normal operational noise is up to 62 dB. If excessive, check if the duct is blocked, the filters are clogged, or the hood is not properly mounted. Clean filters and ensure secure installation.

Can I use the hood without an external exhaust?

This model is designed for ducted operation (air exhaust to outside). It can be used in recirculation mode by adding a carbon filter (not included). Contact the store for compatible filters.

What is the warranty period for the Arçelik ADE 906-2 G?

Arçelik offers a 2-year warranty on manufacturing defects. The warranty covers repair or replacement of defective parts. Keep the purchase receipt for service claims.

How do I change the speed settings?

Use the slider control on the front panel. Sliding up increases speed (1 to 3). Speed 3 is the highest extraction rate for intensive cooking.

What should I do if the hood does not turn on?

Check the power supply: ensure the plug is connected and the circuit breaker is on. If the thermal fuse has tripped, allow the motor to cool down for 15 minutes before restarting. If still not working, contact service.

How do I clean the exterior of the hood?

Use a soft damp cloth with mild detergent. Avoid abrasive cleaners or scouring pads that may scratch the surface. Dry with a soft cloth to prevent water marks.

Where can I find spare parts for the ADE 906-2 G?

Spare parts are available from authorized Arçelik service centers or online spare parts retailers. Provide the model number (ADE 906-2 G) to ensure compatibility. Parts are guaranteed for 10 years after end of production.

USER MANUAL ADE 906-2 G Arçelik

Icon of crossed wrench and screwdriver tools (no text or symbols)

TR / EN

1

2

6

7

Line drawing of a kitchen appliance with four stovels and a mounted stove on a counter, no text or symbols present.

11

12

Technical illustration of two mechanical assembly setups with no visible text or symbols

Technical line drawing of a multi-tiered industrial or electrical cabinet with mounting base and panel, no visible text or symbols

EN - Safety instruction

• Product must be installed by a qualified person in accordance with the regulations in force. The manufacturer shall not be held responsible for damages arising from procedures carried out by unauthorized persons which may also void the warranty.
• Preparation of location and electrical installation for the product is under customer's responsibility. Before calling the Authorized Service, make sure that the electrical installation is suitable. If not, call a qualified electrician to make the necessary arrangements.
• The product must be installed in accordance with all local electrical regulations.
• Before installing the product, remove all the materials and documents in it and visually check if the product has any defects on it. If so, do not have it installed.
• The product is heavy, carry the product with at least two people
• Disconnect electrical connections in the area to be installed before installation.
• Failure to install screws or fixing equipment in accordance with the instructions may result in electrical hazard.
• There may be sharp surfaces on product parts. Always wear protective gloves for installation.

• If the product is not fastened sufficiently, there may be a risk of falling. Make sure that all fixings are securely fastened.

• The width of the hood should be at least equal to the width of your hob.

• The dimensions given in the installation diagrams are in mm.
• The air to be exhausted with the hood should not be given to a chimney used by other devices burning gas or other fuels. (Not only for devices that return air to the room)
• Regulations regarding the exhaust of air must be followed.

Installing the product

Product dimensions and security measures (Picture 1-2)

• Pay attention to product dimensions.
  Check the suitability for your furniture. (Picture 1)
• The height between the lower surface of your hood and the upper surface of the hob should not be less than 650 mm for gas hobs, 500 mm for electrical hobs. (Picture 2)

* In the installation pictures, a demonstration on the gas hob was made as an example, and the size that should be left on the hob was shown as 650 mm. If you have an electric hob, take this measurement as 500 mm as a reference.

Control and preparation of the wall to be installed

- The wall on which the product will be installed must be in an upright and flat position that has the carrying power of the product.

- There must be no water, electricity and gas connections on the wall to be installed and around the holes to be drilled.

Connecting the appliance to the electricity supply

• Manufactured with 2-track power cable, this device must be connected to the mains by an electrical switch with at least 3mm clearance between bipolar contact leads. Have the electrical connections done by a qualified electrician.
• Before starting any work on the electrical installation, disconnect the product from the mains supply. There is the risk of electric shock!
• The product must be connected to the mains supply only by an authorised and qualified person. The product's warranty period starts only after correct installation.

Manufacturer shall not be held responsible for damages arising from procedures carried out by unauthorised persons.

• Install your appliance so that you can reach the power connection (plug, outlet) easily after installation.
- If your product has been produced with plug, do not cut the plug to connect to electrical supply during installation. Otherwise, the warranty becomes void and the safety risks may happen for users.

Installation dimensions and details (Picture 3-4))

• The dimensions in which the product can be installed with a double chimney are shown in picture 3b.
• If you are going to install it with a double chimney, the measure from the required clearance distance above the hob to your furniture should be in the range of 910-1138 mm. (Picture 4b)
• If you are going to install it with a single chimney, the measure from the required clearance distance above the hob to your furniture should be 748 mm. (Picture 3a-4a) For the installation with one chimney, use the upper chimney which has ventilation hole.

Assembling the product fixing parts (Picture 5-6-7)

Your product is described over double chimney sheet assembly sampling.

• Center your hob and draw a vertical axis line on the wall.
• Draw a horizontal reference line measuring 650 mm from the top of your hob. (Picture 5)
• Center the template given with the product on the reference point you have drawn, paste it on the wall and mark the holes in the template with a pencil. (Picture 6)
• Mark the holes for the chimney fixing parts according to the dimensions given in picture 6 from the top of your furniture or ceiling.
• Fix the hood fixing part and chimney fixing parts to the wall as shown in picture 7.

Hanging, aligning and fixing the hood (Picture 8-9-10-11)

- Hang your hood on the hood fixing part that you have fixed to the wall. (Picture 8)

- Align your hob in a central position by sliding the hood left and right on the fixing parts. (Picture 9)

- Open the glass cover of the hood and remove the aluminum filter as shown in picture 10.

- Fix your hood on the hood fixing part as shown in picture 11 with the glass cover open.

- Close the hood glass cover by fitting the aluminum filter into its place.

- Fitting the chimney outlet pipe (Picture 12)

- As shown in the picture 12, place the cover that prevents reversed air flow to the chimney outlet.

- If your chimney connection pipe's diameter is 150 mm place the chimney outlet pipe onto the cover

- If your chimney connection pipe's diameter is 120 mm; Place the chimney outlet pipe after placing the connection adapter on the cover.

- Properly insulate the connection points.

Fixing the chimney sheets (Picture 13-14)

- If your chimney connection pipe's diameter is 120 mm; Stick the supplied tape around the junction of the connection adapter and the air outlet slot. (Picture 13)

- Fix the upper chimney sheet to the upper chimney fixing part with 2 screws from the sides of the curves. (Picture 13)

- Fix the lower chimney sheet to the lower chimney fixing part with 2 screws from the curves on the sides. (Picture 14)

- Complete the installation by fixing the lower chimney sheet with 2 screws from the bottom hole circles on the hood. (Picture 14)

Final check

- Control your hood and lamp by operating it as described in the user manual.