HDD Copy Cruiser 330122 - Copieur de disque dur Aleratec - Free user manual and instructions
Find the device manual for free HDD Copy Cruiser 330122 Aleratec in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Hard Drive Duplicator / Copier |
| Brand | Aleratec |
| Model | HDD Copy Cruiser 330122 |
| Supported Drive Types | 2.5" and 3.5" SATA HDD/SSD |
| Dimensions (approx.) | 200 x 150 x 80 mm (7.9 x 5.9 x 3.1 in) |
| Weight (approx.) | 1.0 kg (2.2 lbs) |
| Power Supply | 12V DC, 2A adapter (included) |
| Copy Speed | Up to 10 GB/min for SATA drives |
| Copy Modes | Disk copy, backup, and verification |
| Standalone Operation | No PC required; copies directly from source to target |
| Supported File Systems | All standard (FAT, NTFS, ext4, etc.) via sector-by-sector copy |
| Display | LCD panel showing progress and status |
| User Interface | Buttons for selection and start/stop |
| Maintenance | Clean exterior with a dry, soft cloth; avoid liquids |
| Safety | Use only the supplied power adapter; do not open the device |
| Spare Parts | Power adapter available from Aleratec support |
| Repairability | No user-serviceable parts; contact professional repair |
| Package Contents | Duplicator, power adapter, user manual |
| Warranty | 1 year limited warranty |
Frequently Asked Questions - HDD Copy Cruiser 330122 Aleratec
What is the maximum drive capacity supported?
The HDD Copy Cruiser 330122 supports any SATA drive capacity up to the maximum available (tested up to 16 TB). There is no firmware limit.
Can I clone an SSD to an HDD or vice versa?
Yes, it supports sector-by-sector copying between any SATA drives, including SSD and HDD of different sizes (target must be equal or larger).
How do I start a clone operation?
Connect the source and target drives, press the Source button, then the Target button to confirm, and press Start to begin copying.
Does it require a computer to operate?
No, the device is standalone and can duplicate drives without any PC connection.
What should I do if the copy fails or shows an error?
Check that both drives are properly seated and powered. Try a different SATA cable. If the error persists, the source drive may have bad sectors; use a different source.
Can I copy a drive that is larger than the target?
No, the target drive must be at least the same size or larger than the source. The duplicator will not copy if the target is smaller.
How long does a typical 1 TB clone take?
At a speed of up to 10 GB/min, a 1 TB clone takes approximately 100 minutes, depending on drive performance and fragmentation.
Is the power adapter universal (110-240V)?
Yes, the included 12V DC adapter accepts 100-240V AC input, so it works worldwide with a simple plug adapter.
Can I use this device to erase a drive?
The primary function is cloning, but you can overwrite a drive by copying blank data. For secure erasure, use a dedicated eraser or software.
How do I clean the device?
Use a soft, dry cloth to wipe the exterior. Do not use any liquids or cleaners. Do not attempt to open the case.
User questions about HDD Copy Cruiser 330122 Aleratec
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Copieur de disque dur in PDF format for free! Find your manual HDD Copy Cruiser 330122 - Aleratec and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. HDD Copy Cruiser 330122 by Aleratec.