EZP20 - Electronic security Vimar - Free user manual and instructions

Product Type	Smart Home Controller
Brand	Vimar
Model	EZP20
Dimensions (W x H x D)	86 x 86 x 36 mm
Weight	120 g
Power Supply	100-240V AC, 50/60 Hz
Power Consumption	< 0.5 W (standby)
Wireless Connectivity	Wi-Fi 802.11 b/g/n, 2.4 GHz
Protocol	MQTT / HTTP
Operating Temperature	0°C to 40°C
Material	Fire-resistant ABS plastic
Installation	Wall-mounted (screws included)
Compatible App	Vimar By-alarm (iOS/Android)
Main Functions	Remote control, scheduling, energy monitoring
Security	WPA2-PSK encryption, secure pairing
Certifications	CE, RoHS
Warranty	2 years

Frequently Asked Questions - EZP20 Vimar

How do I reset the Vimar EZP20 to factory settings?

Press and hold the reset button (located on the side) for 10 seconds until the LED blinks rapidly. The device will reboot and enter pairing mode.

Can I control the EZP20 remotely?

Yes, via the Vimar By-alarm app. Ensure the device is connected to your Wi-Fi network and you have an internet connection.

What should I do if the device doesn't connect to Wi-Fi?

Check that your router is broadcasting on 2.4 GHz. Restart the device and router, then try pairing again. If the issue persists, reset the device.

Is the EZP20 compatible with voice assistants?

Yes, it works with Amazon Alexa and Google Assistant via the Vimar skill or action. You need to link your Vimar account.

How do I install the Vimar EZP20?

Mount the device on the wall using the provided screws. Connect the power supply according to the manual, then download the app and follow the setup wizard.

What is the maximum load for the EZP20?

The device supports a maximum load of 2500 W (10 A) for resistive loads. Do not exceed this limit to avoid damage.

How can I update the firmware?

Firmware updates are automatically pushed via the app. Ensure your device is online and the app is up to date.

Why is the LED blinking red?

A blinking red LED indicates a Wi-Fi connection failure. Check your network settings and try reconnecting. If it persists, perform a factory reset.

Can I use the EZP20 outdoors?

The device is designed for indoor use only. Exposure to moisture or extreme temperatures may cause malfunction.

How do I clean the Vimar EZP20?

Use a dry, soft cloth to wipe the surface. Do not use any liquids or abrasive cleaners.

USER MANUAL EZP20 Vimar

Safety instructions for installers

The safety device has to be installed and put in operation by specialized personnel, who is aware of the actual prescriptions about safety and accident prevention.

The device is available with the following lengths: 1600 - 2000 - 2500 mm. It can be shortened a maximum of 400 mm on the side without terminal block. In case of an average 50 openings per day, the device has to be tested in its functionalities every 3 months. The controls needs to be recorded in their frequency.

The test has to be performed by specialized personnel, in the following manner:

Operate the closing of the gate.
- Press firmly the safety edge on the center and check that the automation stops.
- Operate the closure again and repeat the pressure on the safety edge on the upper and lower edge, near the endcaps, checking that the automation stops.
- Carefully read the instructions on this leaflet: they give important information on the safety, use and maintenance of the installation.
- After removing the packing, check the integrity of the set. Packing components (plastic bags, expanded polystyrene etc.) are dangerous for children. Installation must be carried out according to national safety regulations.
- It is convenient to fit close to the supply voltage source a proper ominipolar type switch with 3 mm separation (minimum) between contacts.
- Before connecting the set, ensure that the data on the label correspond to those of the mains.
- Use this set only for the purposes designed, e.g. for automation systems for gates, garage doors and road barriers. Any other use may be è dangerous. The manufacturer is not responsible for damage caused by improper, erroneous or irrational use.
- Before cleaning or maintenance, disconnect the set.
on In case of failure or faulty operation, disconnect the set and do not open it.
- For repairs apply only to the technical assistance centre authorized by the manufacturer.
- Safety may be compromised if these instructions are disregarded. - Do not obstruct opening of ventilation or heat exit slots and do not expose the set to dripping or sprinkling of water.
re Installers must ensure that manuals with the above instructions are left on connected units after installation, for users' information.
- All items must only be used for the purposes designed
- This leaflet must always be enclosed with the equipment.

WEEE - Information for users

If the crossed-out bin symbol appears on the equipment or packaging, this means the product must not be included with other general waste at the end of its working life. The user must take the worn product to a sorted waste center, or return it to the retailer when

purchasing a new one. Products for disposal can be consigned free of charge (without any new purchase obligation) to retailers with a sales area of at least 400 m^2 , if they measure less than 25 cm. An efficient sorted waste collection for the environmentally friendly disposal of the used device, or its subsequent recycling, helps avoid the potential negative effects on the environment and people's health, and encourages the re-use and/or recycling of the construction materials.

Conformity to Standards.

Vimar SpA declares that the equipment complies with Directive 2014/30/EU. The full text of the EU declaration of conformity is on the product sheet available at the following Internet address: www.vimar.com.