CT-2300 - Receiver Classé - Free user manual and instructions
Find the device manual for free CT-2300 Classé in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Stereo Receiver |
| Brand | Classé |
| Model | CT-2300 |
| Dimensions (W x H x D) | 17.5 x 6.5 x 18.5 inches (44.5 x 16.5 x 47 cm) |
| Weight | 55 lbs (25 kg) |
| Power Output | 200W per channel into 8 ohms, 20-20kHz, both channels driven |
| Frequency Response | 20Hz - 20kHz ±0.25dB |
| Total Harmonic Distortion | <0.02% @ rated power |
| Input Sensitivity | 1.0V (RCA), 2.0V (XLR) |
| Inputs | 6 RCA line-level, 2 XLR balanced, 1 Phono (MM), 1 Tape loop |
| Outputs | Preamp out (RCA), Subwoofer out, Speaker binding posts (2 pairs) |
| Tuner Type | FM/AM with RDS |
| Amplifier Class | Class A/B |
| Remote Control | Included (IR) |
| Power Consumption | 500W (max), <1W standby |
| Voltage | 120V/240V, 50/60Hz (selectable) |
| Cleaning Instructions | Use a soft, dry cloth. Avoid liquids and abrasives. |
| Safety Features | Overcurrent, overvoltage, short-circuit, and thermal protection |
| Spare Parts Availability | Contact authorized Classé service centers for replacement parts. |
| Warranty | 3 years (limited) |
Frequently Asked Questions - CT-2300 Classé
How do I connect my CT-2300 to speakers?
Use high-quality speaker cables with banana plugs or bare wire. Connect to the binding posts, ensuring positive-to-positive and negative-to-negative for each channel. Tighten securely.
What is the recommended impedance for speakers?
The CT-2300 is designed for speakers with an impedance of 4 to 8 ohms. For optimal performance, use 8-ohm speakers.
Can I connect a turntable to this receiver?
Yes, the CT-2300 has a dedicated phono input for moving magnet (MM) cartridges. Connect your turntable's ground wire to reduce hum.
How do I perform a factory reset?
With the unit on, press and hold the 'Menu' button for 5 seconds until 'Reset' appears on the display. Confirm with the 'Enter' button. All settings will return to defaults.
Why is there no sound coming from my speakers?
Check that the speaker wires are properly connected, the input source is selected, and the volume is turned up. Also ensure the receiver is not in 'Mute' mode.
How do I clean the front panel?
Turn off the unit and unplug it. Use a soft microfiber cloth slightly dampened with water. Do not use chemical cleaners or abrasive pads.
What type of remote control does the CT-2300 use?
It comes with an infrared (IR) remote control, model R-2300. Batteries are included. Point the remote directly at the front panel sensor.
Can I use the CT-2300 in a multi-room system?
Yes, it has a preamp output that can be connected to external amplifiers for additional zones. You can also use the subwoofer output for a powered subwoofer.
What is the power consumption in standby mode?
Less than 1 watt. For maximum energy savings, turn off the unit completely when not in use.
Where can I find the serial number?
The serial number is on a label on the back panel of the unit. Keep it handy for warranty service or support inquiries.
User questions about CT-2300 Classé
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual CT-2300 - Classé and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. CT-2300 by Classé.