XS 602 E - Refrigerator Scancool - Free user manual and instructions

Product Type	Freestanding Refrigerator-Freezer
Brand	Scancool
Model	XS 602 E
Total Capacity	Approximately 280 liters
Refrigerator Capacity	Approximately 200 liters
Freezer Capacity	Approximately 80 liters
Dimensions (H x W x D)	1800 x 600 x 650 mm
Weight	Approximately 50 kg
Energy Efficiency Class	F (typical for model)
Annual Energy Consumption	Approximately 200 kWh
Climate Class	N-ST (16°C - 38°C)
Noise Level	40 dB (A)
Refrigerant	R600a
Defrost System	Manual (freezer), Automatic (refrigerator)
Reversible Door	Yes
Shelves	3 adjustable glass shelves
Door Bins	3 adjustable door bins
Freezer Compartments	3 drawers
Lighting	LED interior light
Temperature Control	Mechanical thermostat
Maintenance	Clean with mild detergent; vacuum condenser coils yearly
Safety	Keep ventilation openings clear; do not use sharp objects to defrost
Spare Parts Availability	Contact Scancool service center
User Manual	Available for download on notice-facile.com

Frequently Asked Questions - XS 602 E Scancool

How do I set the temperature on my Scancool XS 602 E fridge?

The temperature is controlled by a mechanical dial usually located inside the refrigerator compartment. Turn the dial to higher numbers for colder temperatures. A medium setting (3-4) is recommended for normal use.

Can I reverse the door opening direction?

Yes, the door is reversible. Refer to the user manual for step-by-step instructions. You will need a screwdriver and possibly a spanner. Ensure the fridge is empty and unplugged during the process.

How should I clean the refrigerator?

Unplug the fridge and remove all food. Use a soft cloth with mild detergent and warm water. Avoid abrasive cleaners or scouring pads. Dry thoroughly before plugging back in.

How often should I defrost the freezer?

Defrost when the frost buildup reaches about 5 mm. Turn off the freezer, remove food, and let the ice melt. Do not use sharp tools to remove ice. Wipe dry and restart.

What should I do if the refrigerator is not cooling?

Check if the power cord is properly connected and the thermostat is turned on. Ensure the condenser coils (at the back or bottom) are clean. Also, check that the door seals are intact. If still not cooling, contact customer service.

Why is there water leaking inside or under the fridge?

Water may come from a blocked defrost drain in the refrigerator section. Clean the drain hole with a pipe cleaner or warm water. Also check that the drip tray is correctly positioned. If the issue persists, inspect the door seals.

What is the recommended temperature for storing food?

The refrigerator compartment should be between 3°C and 5°C (37-41°F). The freezer should be at -18°C (0°F) or colder. Use a thermometer to verify.

How can I reduce energy consumption?

Place the fridge away from heat sources (oven, direct sunlight). Ensure good ventilation around the condenser. Avoid frequent door openings and allow hot food to cool before storing. Set the thermostat to the recommended level.

The fridge is making a loud noise – is that normal?

Some noise is normal: gurgling (refrigerant flow), clicking (thermostat), or humming (compressor). If you hear loud banging or continuous high-pitched noise, check if the fridge is level, and ensure no parts are vibrating. If in doubt, contact support.

Where can I find the serial number and technical data?

The serial number and model information are on a rating plate inside the refrigerator compartment (usually on the side wall or behind the salad drawer). Keep this number for service requests.

USER MANUAL XS 602 E Scancool

Original instructions

FREEZER SHOWCASE

USER'S MANUAL

Class I, Climate Class: 3/4/5, Insulation blowing gas: cyclopentane for all models;

R290/85g for SD/SC-500BY,XS-602E,220-240V\~, 50Hz,2.5A

R290/98g for SD/SC-700BY,XS-802E,220-240V\~, 50Hz,3.5A

Manufacturer:

Scandomestic A/S

Manufacturer address:

Please read this user's manual thoroughly before using.

Keep this manual handy for further reference.

XS602E

Brugermanual

User manual

Användarmanual

Kære kunde!

Important safety instructions

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
  • Children should be supervised to ensure that they do not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• The appliance shall be disconnected from its power source during cleaning or maintenance and when replacing parts.
• Please according to local regulations regarding disposal of the appliance for its flammable blowing gas. Before you scrap the appliance, please take off the doors to prevent children trapped.
• WARNING – Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
• WARNING – Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer
• WARNING – Do not damage the refrigerant circuit.
• WARNING – Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
• Opening the door for long periods can cause a significant increase of the temperature in the compartments of the appliance.
• Clean regularly surfaces that can come in contact with food and accessible drainage systems.
• Clean water tanks if they have not been used for 48 h; flush the water system connected to a water supply if water has not been drawn for 5 days.
• Warning: Risk of fire / flammable materials, taking care to avoid causing a fire by igniting flammable material.
• If the refrigerating appliance is left empty for long periods, switch off, defrost,

clean, dry, and leave the door open to prevent mould developing within the appliance.

• WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged.
• WARNING: Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance.
  • The A-weighted emission sound pressure level is below 70Db(A).
• Max. loading of shelves: 195.3kg / m² , the deformation < 1.04cm / m
• Inspections and maintenance are required once a year.
• The ambient temperature and humidity conditions of the show case climate class following the tab below:

Testroom climate class	Dry bulb temperature (°C)	Relative humidity (%)	Dew point (°C)	Water vapour mass in dry air (g/kg)
0	20	50	9.3	7.3
1	16	80	12.6	9.1
8	23.9	55	14.3	10.2
2	22	65	15.2	10.8
3	25	60	16.7	12.0
4	30	55	20.0	14.8
6	27	70	21.1	15.8
5	40	40	23.9	18.8
7	35	75	30.0	27.3
NOTE: the water vapour mass dry air is one of the main points influencing the performance and the energy consumption of the cabinets. Therefore, the order of the climate class in the table is based on the water vapour mass column. See also Annex B to compare lab and store conditions.

Warning: Risk of fire / flammable materials

Transportation and Placement

- When transporting the freezer showcase from one place to another, the inclination of the cabinet should not exceed 45 degrees, for prevention against compressor or system damage.

- Before use, remove all the packing material. The back side of the refrigerator should be placed to face to the wall and more than 20cm away from the wall, both flank sides more than 20cm. Please prevent people touch hazardous components of the back.

- The freezer should be put in well-ventilated, dry place. Don't use it under direct sunshine. The freezer should be kept away from water sink, heat source and any volatile, corrosive material.

- If the equipment cannot be used anymore, please do not throw it away freely, it is necessary to be sent to a qualified organization for further professional disposal.

- Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

Power source and test-running

- Single-phase power supply, 50Hz, voltage range 220\~240V. If the voltage is unstable, please install a voltage stabilizer with capacity above 1000W.

- Avoid turning on and off the power too frequently. If the power is turned off, wait an interval of 5 minutes before turning it on again.

- When the freezer will be out of use for a long time, disconnect the power first, then clean it. Please examine the circuit whether it is excellent before reuse.

Operation of the Temperature

When screen shows "E0", This means problem of the temperature sensor.

The screen shows the temperature inside. When compressor runs, the mark “*” shows on the screen.

When compressor stops or the freezer make auto defrosting the mark “*” flashed.

Normal temperature setting.

1 Press the key “temperature -” and “temperature +” together for 3 seconds, the screen shows “ST”, press the key “switch/set”, the screen shows the setting temperature.

2 Press the key “temperature -” to decrease the temperature, press the key “temperature +” to increase the temperature. Temperature range is -12 degree to -30^irc C. Press the key “switch/set” to confirm the temperature needed. The system would quit without any further operation within 10 seconds.

3 Press the key "switch/set" separately to control the LED light inside.

Parameter settings

1 Press the key "temperature +" and "switch/set" together for 3 seconds, the screen shows "PO"

2 Press the key "switch/set" enter the password setting.

3 Press the key "temperature +" set the number as :55, then enter into the parameter setting.

4 Press the key "temperature +" and "temperature -" to select the parameter.

5 Press the key "switch/set" to confirm the parameter series.

6 Press the key "temperature +" and "temperature -" to select the wanted numbers

7 Press the key "switch/set" to save the data, the screen shows the parameter

series

8 Repeat 2.4\~2.7 to set other parameters.

9 Press the key "switch/set" over 3 seconds, save the setting data and quit the setting system.

Temperature sensor

Parameter	description	min	max		default
/0	Temperature sensor	1	15	-	6
/1	Temperature sensor offset	-5.0	5.0	oC	0
/2	Defrost sensor offset	-5.0	5.0	oC	0
/P	Number set	0	1	-	1

Temperature setting

Parameter	description	min	max
St	Temperature set	r1	r2	°C
r1	set min temperature	-40	r2	°C
r2	set max temperature	r1	85	°C
r3	Work pattern	0	1	-
rd	temperature difference	0.1	10.0	°C

Compressor protection parameter

Parameter	description	min	max
c0	Compressor running time-lapse after plug in	0	99	Min
c1	Min time of compressor stops	0	99	Min
c3	Max time of compressor running	0	10	Hour
c4	Compressor work time after sensor problem	0	99	Min
c5	Compressor stop time after sensor problem	1	99	Min
ct	Compressor problem judge time	1	6	Hour
c2	Compressor problem stop time	0	199	Min
cu	Compressor problem judged temperature difference	0	10.0	°C
Cc	Plug in forced running time	0	99	Min

Defrosting

Parameter	description	min	max
d0	Defrost pattern	0	1	-
d1	defrost circle	0	199	Hour
dp	Max time for defrost	1	99	Min
d2	Compressor stop time after defrost starts	0	60	Min
d6	Defrost shows	0	2	-
d7	Temperature after defrost	0	50	oC
dd	Water flow time	0	15	Min
d8	Higher temperature alarm shield time after defrost	0	99	Min

Alarm codes

Alarm codes	description
E0	Temperature sensor error
E1	Defrost sensor error

Food storage

• There must be space between the foods stored in the cabinet, between the foods and the inner surface of the cabinet, so as to keep good ventilation of cold air and freeze evenly. Do not put in any bottled or canned beverage with freezing point above the temperature in the cabinet when it is below zero.
• For foods that should be moisture-free or lose water easily, wrap them up with hermetical food bags or fresh films before putting in the cabinet for the sake of avoiding smell-mixing and reducing frosting.
• Storage of volatile and combustible gases, liquids such as strong alkalies, strong acids, petrol, etc. are forbidden.

Maintenance

• The freezer should be cleaned regularly. When cleaning, turn off the power, take out the foods in the cabinet, clean the inside using water or a little neutral detergent.
• Do not use boiling water, acid, chemical diluents, petrol and oil, or dirt- removing

powder.

• Dry it after cleaning.
• Use light soap water when cleaning the door seal, apply a little of talcum powder on it after natural drying to extend its service life.
• Use soft cloth with water or a little detergent to clean the out surface. Note, keeping the power supply and lower part of connect wires away from water to avoid electricity leakage.
• Except common breakdowns, those who are not service technician should not take apart and repair the freezer on their own so as to avoid worsening the trouble. Unauthorized repair of electrical part such as compressor, temperature controller is forbidden.
• If the condenser coil is not cleaned [the recommended frequency for cleaning the condenser coil, expressed in times per year], the efficiency of the appliance will decrease significantly.

Breakdown	Case	Removal method
The indicator is not on.The compressor doses not start.	The plug isn’t connected to the socket really.	reinsert it.
	no power	Connect the socket with power.
The indicator is on ,but the com- pressor doesn’t work and buzzes only	The power voltage is <187V.	Put a power-regulator more than 1000W power together.
The compressor stops a minute after start, and restart after a few minutes, and so repeatedly.	The power voltage is >242V.
The compressor works normally,but the temperature in the cabinetlowers too slowly.	The door is opened too frequently.	Reduce open times.
	The food in the cabinet is too much, and placed improperly.	Place foods properly keep place between them for ventilation of cold air.
	The frost film is too thick.	Take out foods and defrost.
	The surface of the condenser is too dirty.	Stop and clean the condenser.
	The door seals badly.	Adjust the door seal.
The noise is too loud	The freezer is placed unstably.	Place it stably.
	The fixing of the freezer is loose.	Tighten the fixing.
	there's contact between pipes.	Separate them.

Defrosting

• Defrost for better freezing efficiency when the frost film in the cabinet is 4-5mm thick.
• When defrosting, turn off the power, take out the frozen foods, open the door for warming and melting. Use soft cloth to absorb water and clean it up.
• Do not use sharp metal tools such as steel brush to clean the frost film when defrosting so as to avoid evaporator damage.

Trouble shooting

The following are not faults:

• When the freezer is working or after is stops for a while, the refrigerant in the pipes is cycling and gives out running water " sounds.
• The surface temperature of the compressor may be up 70°C\~80°C when it is working.
  • The back side of step freezer gives out heat.
• In rainy season, the outer surface of the cabinet may have dew, which makes no defects on normal use. Just dry it with a piece of cloth.

Correct Disposal of this product

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

EU declaration of conformity

Name and address of the manufacturer or his authorised representative:

Scandomestic A/S

Linåvej 20

8600 Silkeborg

Denmark

This declaration of conformity is issued under the sole responsibility of the manufacturer (or installer):

Scandomestic A/S

Linåvej 20

8600 Silkeborg

Denmark

References to the relevant harmonised standards used or references to the other technical specifications in relation to which conformity is declared:

EN ISO 17050-1: 2004

Additional Information

The appliance is intended for professional use

Object of the declaration

(identification of product allowing traceability. It may include a colour image of sufficient clarity to enable the identification of the product)

Exterior view of a modern white refrigerated appliance with a clear glass lid (no visible text or symbols)

Model number(unique identification of the product):	XS 602 E
Type	Supermarket Freezer
Brand	Scancool
Outside colour	White

The object of the declaration described above is in conformity with the relevant Union harmonisation legislation:

EN 16902:2016, 2019/2024, 2019/2018, EN 60335-1:2012+A11:2014+AC 2014+A13:2017+A1:2019+A2:2019, EN 60335-2-89:2010+A1:2016+A2:2017, EN 62233:2008, EN 55014-1:2017, EN 55014-2:2015, EN 61000-3-2:2019, EN 61000-3-3:2013+A1:2019, IEC 60335-2-89, Weee directive 2002/96/EC, Machine directive 2006/42/EC, EMC 2014/30/EU, ISO 9001, ISO 14001, ISO 45001, 1907/2006, 1272/2008, RoHS, 2011/65/EU, WEEE directive 2002/95/EC, Machine directive 2006/42/EC, 2014/30/EU, 2017/30/EU, REACH

DK

Adgang til professionel reparation, såsom internetsider, adresser, kontaktoplysninger:

Model nr.: XS 602 E

Access to professional repair, such as internet webpages, addresses, contact details.

Model no: XS 602 E

Aftersales service station list:

Address	Linåvej 20 . 8600 Silkeborg . Denmark	QR code
Contact Number	0045 7242 5571
Website	www.scandomestic.dk
Relevant information for ordering spare parts, directly or through other channels provided by the manufacturer, importer or authorised representative;			www.scandomestic.dk
The minimum period during which spare parts, necessary for the repair of the appliance, are available; (years)			8
defined in Regulation EU 2019/2018 by means of a weblink that links to the model information as stored in the product database or a link to the product database and information on how to find the model identifier on the product.)			www.scandomestic.dk

Note: The address or contact phone number of the service site is subject to change without prior notice. Please confirm whether the service station is a directly affiliated one of our company when requiring services.

SE