AP9613 - Inverter APC - Free user manual and instructions
Find the device manual for free AP9613 APC in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | UPS / Inverter |
| Brand | APC |
| Model | AP9613 |
| Dimensions (H x W x D) | 17.3 x 5.1 x 17.0 inches |
| Weight | 84 lbs (38.1 kg) |
| Input Voltage | 120 V AC |
| Output Voltage | 120 V AC |
| Power Capacity | 1500 VA / 1000 W |
| Battery Type | Sealed lead-acid (SLA) |
| Typical Backup Time (Half Load) | Approximately 10 minutes |
| Surge Protection | Yes |
| Number of Outlets | 8 (UPS battery & surge) + 2 (surge only) |
| Communication Ports | DB-9 serial, USB, SmartSlot |
| Software Included | PowerChute Personal Edition |
| Operating Temperature | 32°F to 104°F (0°C to 40°C) |
| Maintenance | Replace battery every 3-5 years; clean with dry cloth |
| Safety Features | Overload protection, short-circuit protection, Automatic Voltage Regulation (AVR) |
| Replaceable Parts | Battery cartridge (model RBC6), fans |
| Repairability | User-replaceable battery, other repairs by qualified technician |
| Certifications | UL, CSA, NOM, FCC Part 15 |
Frequently Asked Questions - AP9613 APC
How do I replace the battery in the APC AP9613?
Turn off the UPS and disconnect it from AC power. Open the front panel, remove the old battery cartridge (model RBC6), and insert the new one. Close the panel and reconnect power. Refer to the manual for detailed steps.
What is the expected runtime of the AP9613 at full load?
At full load (1000W), the runtime is approximately 2-3 minutes. At half load (500W), it is about 10 minutes. Actual runtime depends on battery age and load.
Can I connect a printer or laser printer to the AP9613?
Yes, but be aware that laser printers draw high startup current. It is recommended to connect them to the surge-only outlets to avoid overloading the battery during a power outage.
How do I test the UPS functionality?
Press the test button on the front panel for 2 seconds. The UPS will perform a self-test and report results via LED indicators or software. For a more accurate test, use PowerChute software.
What do the front panel LEDs indicate?
Green LED: normal operation. Yellow LED: battery backup active or low battery. Red LED: fault or overload. Flashing patterns indicate specific alarms. Consult the manual for a full legend.
How do I connect the AP9613 to a computer?
Use the USB cable or serial cable to connect the UPS to your computer. Install PowerChute software to monitor and control the UPS. For network management, insert a SmartSlot card.
What is the warranty for the APC AP9613?
Typically, APC offers a 2-year warranty from the date of purchase. Register your product on the APC website to extend the warranty if available.
Can the AP9613 be rack-mounted?
Yes, the AP9613 is designed for both tower and rack-mount configurations. It comes with mounting brackets for standard 19-inch racks. Ensure proper ventilation.
How do I perform a battery calibration?
Disconnect the UPS from AC power and allow it to run on battery until it shuts down due to low battery. Reconnect AC power and let the battery charge fully. This recalibrates the runtime estimation.
What should I do if the AP9613 emits a continuous alarm?
A continuous alarm indicates a fault. Disconnect all loads and check for overload, battery failure, or internal error. Contact APC support or refer to the troubleshooting guide in the manual.
User questions about AP9613 APC
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Inverter in PDF format for free! Find your manual AP9613 - APC and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. AP9613 by APC.