PSP6 - Subwoofer Metra - Free user manual and instructions

Product Type	Subwoofer
Brand	Metra
Model	PSP6
Size	12 inches (30.5 cm)
Impedance	4 ohms
Power Handling (RMS)	200 Watts
Power Handling (Peak)	400 Watts
Frequency Response	20 Hz - 200 Hz
Sensitivity	90 dB
Weight	8 kg (17.6 lbs)
Mounting Depth	6 inches (152 mm)
Cutout Diameter	11.1 inches (282 mm)
Cone Material	Polypropylene
Surround Material	Rubber
Magnet Weight	40 oz (1134 g)
Recommended Enclosure	Sealed or Ported
Warranty	1 Year
Cleaning	Wipe with dry cloth
Safety	Do not expose to moisture; ensure proper ventilation
Spare Parts Availability	Contact Metra customer support

Frequently Asked Questions - PSP6 Metra

What is the power handling of the Metra PSP6 subwoofer?

The Metra PSP6 handles 200 Watts RMS and 400 Watts peak power.

What is the impedance of this subwoofer?

The impedance is 4 ohms, suitable for most car audio amplifiers.

What type of enclosure is recommended?

Both sealed and ported enclosures work. A sealed box provides tighter bass, while a ported box gives more output.

What is the mounting depth?

The mounting depth is 6 inches (152 mm). Ensure your enclosure has enough depth.

What is the frequency response range?

The frequency response is 20 Hz to 200 Hz, covering deep bass to mid-bass.

How do I clean the subwoofer?

Gently wipe the cone and surround with a dry, soft cloth. Do not use liquids.

Does this subwoofer require a break-in period?

Yes, play it at moderate volume for 10-15 hours to loosen the suspension for optimal performance.

What is the sensitivity rating?

The sensitivity is 90 dB, meaning it produces moderate volume with standard power.

Can I install this subwoofer in a car?

Yes, it is designed for car audio systems. Ensure proper enclosure and amp matching.

Where can I find spare parts or support?

Contact Metra customer service or visit their official website for replacement parts or assistance.

USER MANUAL PSP6 Metra

We would like to thank you for your purchase of the Precision Port™.

The Precision Port ^™ was created for you, the audiophile, for clearer sound, greater SPL and better cosmetics.

INSTALLATION PROCESS

We recommend installation by a qualified installer if possible. If one is not available follow the instructions below.

1. Calculate length of port needed:

$$ \mathrm{Lv} = \frac {8 4 6 6 . 4 \mathrm{R} ^ {2}}{(\mathrm{Vb}) \mathrm{Fb} ^ {2}} - 1. 4 6 3 \mathrm{R} $$

Lv= port length in inches

Vb= volume of box in cubic feet

Fb= tuning frequency

R= radius of port (1/2 of port diameter)

1. Determine proper speaker & port placement before cutting any holes. The Precision Port™ can be placed as close as 1" from the inside wall of the enclosure although it is recommended to keep it as far away from the inside wall as possible.

2. Once placement has been determined cut the proper size hole.

3. Trim center tube to 5" shorter than Lv from step one.

4. The Precision Port™ should be 1" longer than Lv when assembled.

5. If you want to use screws to attach the port to the enclosure use the guide marks on the back of the outside flare. The screw holes are numbered with a 6 or 8 for the number of screws you would like to use.

6. When the length has been achieved the Precision Port™ can be glued together using ordinary ABS adhesive or similar type glue. Once pieces are assembled with ABS adhesive, pieces can not be taken apart.

Assemble the Precision Port™ in the following manner.

1. Attach connecting rings to flared ends.

2. Slide flared ends, with connecting rings attached, over tube section.

DO NOT ATTACH INSIDE FLARE UNTIL PORT HAS BEEN INSTALLED IN ENCLOSURE.

1. Insert the Precision Port ^TM into enclosure and secure with adhesive and/or screws. It is recommended to use adhesive when screwing in port.

WARRANTY

The Precision port™ is warranted, to the original purchaser, for a period of 90 days from the date of purchase. This warranty is limited to any manufacturing defects. If such a defect is found contact the place from which you purchased this product.