Q: How to obtain the motor start capacitor for the ARGO Oscar air conditioner?

To identify the exact part: Check the technical label attached to your ARGO Oscar air conditioner (usually at the back or on the side) which indicates the full model number and the manufacturing date. The start capacitor is a small cylindrical component located near the compressor (inside the unit). To obtain it: Contact ARGO's customer service directly with the model "Oscar" and the serial number - they will provide the exact part code. Consult an electronic spare parts distributor (Spareka, Fixpart or local dealers specialized in air conditioning). Consider having a certified technician intervene if you are not comfortable with replacing it yourself, as it is a critical electrical part for starting the motor.

Q: What are the dimensions of the hot air exhaust hose of the ARGO Oscar air conditioner?

The ARGO Oscar air conditioner comes with a retractable flexible hose with terminal connector for hot air exhaust. However, the technical manual does not specify the exact dimensions (diameter, length) of the hose in detail. What you need to know: The flexible hose should be handled carefully during installation - avoid bending or folding it too much to not compromise the airflow The unit comes with all necessary accessories including the terminal connector and a window kit for installation on glass To find out the precise dimensions of the hose (especially the diameter), we recommend that you: Check the rating plate on your unit Consult the original packaging documents Contact ARGO customer service if the hose needs to be replaced

Q: How to start and use the ARGO Oscar air conditioner?

Initial startup: Place the unit near a window or opening. Unfold the flexible tube and securely attach it to the back of the air conditioner. Pass the tube outside through the window or an opening. Plug the unit into a 220-240 V grounded outlet. Press the power button (A) to turn on the air conditioner. Cooling mode: Press the (B) cooling button. The (E) indicator lights up. Select the fan speed using the (C) button (high or low speed). The (F) indicator lights up for high speed. Adjust the desired temperature using the electronic thermostat (D) . The unit will cool effectively when the ambient temperature is above 15°C. Dehumidification mode: Remove the flexible tube (moisture collects in the internal tank instead of being expelled). Press the (B) button until the (H) indicator lights up. This mode works if the ambient temperature is above 10°C. Empty the tank when the indicator flashes (capacity of about 6 hours). Maintenance: Clean the filter every 15 days by vacuuming or with lukewarm soapy water. Clean the casing with a damp soft cloth (avoid solvents and hot water). Important: The compressor automatically protects itself in case of overload and will restart after 3 minutes.

Question 1

Does the ARGO Oscar air conditioner have a secondary tank?

Accepted Answer

Yes, the ARGO Oscar air conditioner is equipped with a secondary tank. In addition to the main tank, the unit has a secondary tank that must be drained during certain maintenance operations.

To access and drain the secondary tank, refer to the drainage tube located inside the unit's electrical cable compartment. It is important to also drain this secondary tank during seasonal storage or when moving the unit.

The secondary tank serves a safety and efficiency function for the unit's condensation system. Be sure to regularly check its condition and drain it if necessary to ensure the proper functioning of the air conditioner.

Question 2

The ARGO Oscar air conditioner is not cooling and is not producing condensation: what should I do?

Accepted Answer

The simultaneous absence of cooling and condensation generally indicates that the compressor is not operating. Here’s how to diagnose:

1. Basic electrical checks

Ensure that the air conditioner is properly plugged into a functioning power outlet (220-240V ~50Hz)
Check that the recommended 20A circuit breaker or 10A delayed fuse has not tripped
Press the Power button to turn on the unit - the 24h timer display should appear
Ensure you are in cooling mode (not in fan-only mode)

2. Compressor restart delay

The compressor of the Oscar air conditioner is protected against overloads by a 3-minute automatic restart delay. If you have recently turned the unit off and back on, wait at least 3 minutes before cooling resumes.

3. Insufficient ambient temperature

The air conditioner can only operate if the ambient temperature exceeds 15°C in cooling mode (dry sensor). If your room is colder than this, the compressor will not start automatically for safety reasons.

4. Incorrectly set thermostat

The thermostat of the Oscar air conditioner is a continuous electronic selection knob (not a numeric scale 1-5). Turn it fully to the right to force maximum cooling and check that the compressor starts.

5. Clogged filter

A dirty filter drastically reduces cooling performance. Clean the main filter as well as the removable deodorizing purification filter every 2 weeks with a vacuum cleaner or warm soapy water. If the filter is very dark, use the replacement slider provided with the air conditioner as a reference.

6. Clogged drainage system

At high fan speed, the air conditioner automatically expels condensation outside via the retractable flexible tube with terminal connection. At low speed, water accumulates in the internal tank (autonomy ~6 hours). Check that:

The drainage tube is not bent, crushed, or blocked
The tube is not removed or poorly connected to the drainage terminal
The internal tank is not overflowing (empty it if necessary)

Note on condensation: If the unit cools but does not produce visible condensation, this is normal at high speed - all water is then automatically expelled outside. You will only see condensation if you switch to low speed.

If after these checks the compressor still does not start and no operating noise is audible, contact ARGO support - the air conditioner may require a refrigerant recharge or compressor repair.

Question 3

How to obtain the motor start capacitor for the ARGO Oscar air conditioner?

Accepted Answer

To identify the exact part:

Check the technical label attached to your ARGO Oscar air conditioner (usually at the back or on the side) which indicates the full model number and the manufacturing date.
The start capacitor is a small cylindrical component located near the compressor (inside the unit).

To obtain it:

Contact ARGO's customer service directly with the model "Oscar" and the serial number - they will provide the exact part code.
Consult an electronic spare parts distributor (Spareka, Fixpart or local dealers specialized in air conditioning).
Consider having a certified technician intervene if you are not comfortable with replacing it yourself, as it is a critical electrical part for starting the motor.

Question 4

Why does the ARGO Oscar air conditioner turn off automatically shortly after being turned on?

Accepted Answer

The Oscar air conditioner turns off automatically for several safety or normal operating reasons:

Full condensation tank

The most common cause is that the condensation tank is full. When the internal tank is saturated, the air conditioner automatically stops and the 'full tank' indicator starts to blink. The tank provides about 6 hours of operation before it needs to be emptied.

Solution: Check if the tank indicator is blinking on the control panel. If so, empty the condensation tank by following the instructions in the manual.

Compressor protection (3-minute delay)

The air conditioner has overload protection with a 3-minute restart delay. This safety feature prevents the compressor from restarting immediately after a shutdown, which could damage it.

Solution: If the air conditioner turns off and then back on a few seconds later, wait at least 3 minutes before restarting it.

Ambient temperature too low

The air conditioner only operates within certain temperature ranges:

Cooling mode: The ambient temperature must exceed 15°C
Dehumidification mode: The ambient temperature must exceed 10°C

If the temperature drops below these thresholds, the compressor automatically stops.

Fan speed

At low fan speed, condensation water is collected in the tank. At high speed, the air conditioner automatically removes the condensation. If you are using a low speed and the tank fills up, the automatic shutdown is triggered.

Solution: Try increasing the fan speed to allow for automatic removal of the condensation.

Question 5

What is the BTU power of the ARGO Oscar air conditioner?

Accepted Answer

The technical manual of the ARGO Oscar air conditioner does not specify the cooling power in BTU/h. However, the manual indicates the following characteristics:

Power supply: 220-240V ~ 50Hz, protected by a 20A circuit breaker (10A time-delay fuse)
Operating modes: cooling, dehumidification, and ventilation
Compressor: protected against overloads with a 3-minute restart delay
Minimum conditions: 15°C in cooling mode (dry temperature)
Condensate tank autonomy: approximately 6 hours

To find out the power in BTU/h or kW of your ARGO Oscar model, we recommend checking the technical nameplate of the device (usually on the back or side) or contacting ARGO customer service with your serial number.

Question 6

Does the thermostat of the ARGO Oscar air conditioner have a numerical scale from 1 to 5?

Accepted Answer

No, the thermostat of the ARGO Oscar air conditioner does not have a numerical scale from 1 to 5. The thermostat knob (D) is a continuous selector, not a graduated scale.

Here’s how to use it correctly:

For maximum cooling: Turn the selector to the right until you reach the maximum cooling position.
To stop the compressor: Slowly turn the selector to the left.
To maintain a temperature: Once the desired temperature is reached in your room, the thermostat automatically maintains this temperature by turning the compressor on and off as needed.

Therefore, there is no position

Question 7

How to reach the coldest temperature with the ARGO Oscar air conditioner?

Accepted Answer

To achieve the coldest temperature with the ARGO Oscar air conditioner, you need to turn the thermostat selector (D) all the way to the right to the extreme position.

Here is the complete procedure:

Press the power button (A) to start the unit
Select the cooling mode with button (B)
Choose the desired fan speed with button (C) - the high speed offers faster cooling
Turn the thermostat selector (D) all the way to the right to reach maximum cold

Important: The thermostat of this unit is a continuous selector without a numerical scale. Once the desired temperature is reached, it automatically maintains that temperature. For optimal cooling, ensure that the ambient temperature is above 15°C (dry bulb).

Question 8

Does the ARGO Oscar air conditioner need refrigerant recharging?

Accepted Answer

No, the ARGO Oscar air conditioner does not need to be recharged by the user. The refrigerant is sealed in a closed circuit inside the unit and does not get consumed during normal operation.

If your air conditioner is not cooling properly, it does not necessarily mean that it is low on refrigerant. First, check:

The filter - Clean it every 15 days or so to maintain good air circulation
The installation - Ensure that the hot air exhaust hose is properly connected to a window or door
The ambient temperature - The unit works best under normal conditions

If after these checks the cooling remains weak, a refrigerant leak is possible. In this case, contact ARGO customer service - it is the only authorized intervention on the refrigerant circuit. Do not attempt to recharge it yourself, this is not intended for this portable unit.

Question 9

What are the dimensions of the hot air exhaust hose of the ARGO Oscar air conditioner?

Accepted Answer

The ARGO Oscar air conditioner comes with a retractable flexible hose with terminal connector for hot air exhaust. However, the technical manual does not specify the exact dimensions (diameter, length) of the hose in detail.

What you need to know:

The flexible hose should be handled carefully during installation - avoid bending or folding it too much to not compromise the airflow
The unit comes with all necessary accessories including the terminal connector and a window kit for installation on glass

To find out the precise dimensions of the hose (especially the diameter), we recommend that you:

Check the rating plate on your unit
Consult the original packaging documents
Contact ARGO customer service if the hose needs to be replaced

Question 10

How to start and use the ARGO Oscar air conditioner?

Accepted Answer

Initial startup:

Place the unit near a window or opening.
Unfold the flexible tube and securely attach it to the back of the air conditioner.
Pass the tube outside through the window or an opening.
Plug the unit into a 220-240 V grounded outlet.
Press the power button (A) to turn on the air conditioner.

Cooling mode:

Press the (B) cooling button. The (E) indicator lights up.
Select the fan speed using the (C) button (high or low speed). The (F) indicator lights up for high speed.
Adjust the desired temperature using the electronic thermostat (D).
The unit will cool effectively when the ambient temperature is above 15°C.

Dehumidification mode:

Remove the flexible tube (moisture collects in the internal tank instead of being expelled).
Press the (B) button until the (H) indicator lights up.
This mode works if the ambient temperature is above 10°C.
Empty the tank when the indicator flashes (capacity of about 6 hours).

Maintenance:

Clean the filter every 15 days by vacuuming or with lukewarm soapy water.
Clean the casing with a damp soft cloth (avoid solvents and hot water).

Important: The compressor automatically protects itself in case of overload and will restart after 3 minutes.

User manual ARGO : user manuals and guides in PDF

Models ARGO most viewed

Browse manuals ARGO by appliance type

Recent questions about devices ARGO