Q: How to use the NEW POL XF5 600 washing machine?

Before first use: Remove the 4 transport protections with screws and plug the holes. Place the washing machine on a stable surface, adjust the feet to level it, and then connect the cold water supply and drainage hoses (the drainage height must be between 60 and 90 cm). Plug into a grounded outlet. Starting: Ensure that the door is properly closed, select the washing program suitable for your textiles, and then press the on/off button or pull the timer according to your model. Cycle programming: Your NEW POL XF5 600 offers several types of programs including pre-wash, soaking, and normal wash. Choose the one that suits your laundry load. Detergent: The detergent drawer has three distinct compartments: one for pre-wash, one for the main wash, and one for fabric softener. Use a low-foaming detergent and do not mix products. Opening the door: At the end of the cycle, wait at least 3 minutes before opening the door. On electronic models, the

Q: What is imbalance (desbalance) in a NEW POL XF81408DG washing machine?

Imbalance in a washing machine, often referred to as desbalance , occurs when the load of laundry inside the drum is not evenly distributed. This means that one part of the drum is more loaded than the other, causing irregular movement during the spin cycle. Consequences of imbalance: Stop of the spin cycle: The machine may interrupt the cycle to avoid damage or excessive noise. Excessive vibrations: An unbalanced drum can lead to shaking or unusual movements of the machine. Ineffective spinning: The machine may not reach the optimal spin speed. How to avoid imbalance: Distribute the laundry evenly in the drum. Avoid overloading the machine. Mix heavy clothes with lighter clothes to balance the load. By following these tips, you ensure optimal operation of your NEW POL XF81408DG washing machine and avoid problems related to imbalance.

Question 1

How to use the NEW POL XF5 600 washing machine?

Accepted Answer

Before first use: Remove the 4 transport protections with screws and plug the holes. Place the washing machine on a stable surface, adjust the feet to level it, and then connect the cold water supply and drainage hoses (the drainage height must be between 60 and 90 cm). Plug into a grounded outlet.

Starting: Ensure that the door is properly closed, select the washing program suitable for your textiles, and then press the on/off button or pull the timer according to your model.

Cycle programming: Your NEW POL XF5 600 offers several types of programs including pre-wash, soaking, and normal wash. Choose the one that suits your laundry load.

Detergent: The detergent drawer has three distinct compartments: one for pre-wash, one for the main wash, and one for fabric softener. Use a low-foaming detergent and do not mix products.

Opening the door: At the end of the cycle, wait at least 3 minutes before opening the door. On electronic models, the

Question 2

What is imbalance (desbalance) in a NEW POL XF81408DG washing machine?

Accepted Answer

Imbalance in a washing machine, often referred to as desbalance, occurs when the load of laundry inside the drum is not evenly distributed. This means that one part of the drum is more loaded than the other, causing irregular movement during the spin cycle.

Consequences of imbalance:

Stop of the spin cycle: The machine may interrupt the cycle to avoid damage or excessive noise.
Excessive vibrations: An unbalanced drum can lead to shaking or unusual movements of the machine.
Ineffective spinning: The machine may not reach the optimal spin speed.

How to avoid imbalance:

Distribute the laundry evenly in the drum.
Avoid overloading the machine.
Mix heavy clothes with lighter clothes to balance the load.

By following these tips, you ensure optimal operation of your NEW POL XF81408DG washing machine and avoid problems related to imbalance.

Question 3

What does the click heard on my NEW POL XF81408DG washing machine mean and how can I check if the water level sensor is working properly?

Accepted Answer

The click you hear on your NEW POL XF81408DG washing machine is generally related to the operation of the water level sensor. This sensor emits a sound signal when it activates, indicating that it detects the water level in the drum.

Interpretation of the click

This click is a sign that the water level sensor is functioning at its mechanical or electronic activation level. However, hearing this click does not guarantee that the system is filling the machine with water correctly.

Checks to perform if the machine is not filling correctly

Check the pressure hose: This hose connects the drum to the sensor. Make sure it is not blocked or damaged, as a blockage can distort the water level reading.
Check the water inlet valve: Even if it has been replaced, check that it is functioning correctly, is not blocked, and is receiving the necessary electrical supply.
Examine the electrical wiring: A damaged or poorly connected wire between the sensor, the valve, and the control board can prevent proper filling.
Check the electronic board: If all the previous components are in good condition, a malfunction of the control board may prevent the valve from opening and filling.

In summary, the click is a good sign that the sensor is activating, but it is important to check the other components to ensure adequate filling of the washing machine.

Question 4

Where is the water level sensor located on the NEW POL XF81408DG washing machine?

Accepted Answer

The water level sensor, also known as a pressure switch, is an essential component of the NEW POL XF81408DG washing machine that measures the water pressure in the drum to control the filling.

Location of the water level sensor

It is generally located inside the machine, often at the back or on the side, near the drum.
The sensor is connected to a small hose (rubber tube) that transmits the water pressure to the pressure switch.

How to identify the sensor?

Look for a small electronic box with one or more electrical connections.
A thin hose runs from this box to the drum or tub.

Precautions for accessing the sensor

Always unplug the washing machine before any intervention.
It may be necessary to remove the back or top panel to access the sensor.
If you are not comfortable with these manipulations, it is advisable to call a professional.

Question 5

Why does the water inlet valve of my NEW POL XF81408DG washing machine work at first and then stop working?

Accepted Answer

If the water inlet valve of your NEW POL XF81408DG washing machine works correctly at the beginning of the cycle and then stops supplying water to the machine, several common faults may be responsible:

Clogged water inlet filter - This is the most frequent cause of this malfunction. Over time, impurities (lime scale, rust, particles) accumulate in the filter located at the inlet of the valve. This filter gradually restricts the water flow until it completely stops it. To check: turn off the main water tap, unscrew the inlet valve (two hoses are usually present), and then inspect the filter. A white or yellowish filter indicates a blockage. Clean it gently with water or replace it if necessary.

Insufficient or variable water pressure - Your XF81408DG machine requires a water pressure between 0.05 and 1 MPa. If your water flow decreases during the cycle (a common problem during peak hours), the valve stops working because it no longer detects enough pressure. Check that the supply tap is fully open and that your installation does not have any leaks.

Defective solenoid valve - The valve contains a solenoid that opens and closes electrically. After a few years of use, the solenoid may get stuck or become defective and no longer respond correctly to the closing command. It initially allows water to pass (beginning of the cycle), then gradually gets blocked.

Internal limescale buildup - In areas with very hard water, limescale accumulates inside the internal pipes of the valve, gradually reducing the flow. Use a specialized descaler for washing machines or periodic cleaning to prevent this problem.

Faulty water level sensor - The sensor indicates to the machine when the drum is full. If it malfunctions after the initial filling, the electronics may close the valve prematurely, preventing the wash from continuing properly.

We recommend first cleaning the inlet filter (a simple and free operation), and then contacting an authorized repairer if the problem persists. In hard water areas, regular descaling will prolong the life of the valve.

User manual NEW POL : user manuals and guides in PDF

Models NEW POL most viewed

Browse manuals NEW POL by appliance type

Recent questions about devices NEW POL